Birefringent azopolymer long period fiber gratings induced by 532 nm polarized laser

Based on the photoinduced birefringence in azo materials, the model of the birefringent long period fiber gratings (BLPFGs) has been proposed and the transmission of such birefringent fiber gratings was further simulated by the coupled mode theory. In order to obtain the optimum condition for making birefringent azopolymer optical fiber (APOF) gratings the photoinduced birefringence of azo dye and methyl methacrylate (MMA) copolymers was systematically studied. After photosensitivity study of azo samples, using Teflon technique, azo dye containing single mode polymer optical fiber (POF) was fabricated. Finally, BLPFGs can be fabricated in azopolymer fiber using polarized 532 nm laser. A 120 μm LPFG with a 50% duty cycle has been successfully written within the core of the fiber with 532 nm laser by an amplitude mask method. Under polarized microphotography, the grating was observed when the optical axis was set at 45° with the direction of the first polarizing lens of the polarization microscope.     

非均匀微结构光纤中双折射现象的研究

报道了利用飞秒脉冲激光与非均匀微结构光纤相互作用中产生超连续光谱后在非均匀微结构光纤传输中双折射拍频现象的研究.利用35?fs的飞秒激光脉冲在高双折射微结构光纤中的传输过程中直接观察到了拍频现象.并利用有限元方法对该光纤进行了模拟计算分析，计算得出在600?nm处拍频长度为毫米量级.所得结果与实验一致. 关键词： 双折射效应 微结构光纤 超连续光谱 有限元法     

Continuous-wave solid-state dye laser

We report the first realization of a cw solid-state dye laser. The laser medium consists of a laser dye (Rhodamine 6G) dissolved in a photopolymer. The UV-cured solution is sandwiched between two DVD substrates. The resonator design was derived from a conventional liquid solvent dye laser geometry. The laser radiation can be tuned from 565 to 615 nm by using a birefringent filter. A pump power of 2 W leads to a cw output power of more than 20 mW.     

用于定向红外对抗的中波红外激光器技术

针对定向红外对抗系统对中波红外激光器在激光波段、激光功率、激光束散角、激光重复频率以及调制波形等方面的具体要求,通过对光泵半导体激光器、量子级联激光器和基于光学参量振荡的固体以及光纤激光器的技术特点与发展现状的分析比较,和对双折射相位匹配与准相位匹配的特点和最新发展动态的梳理,提出用高功率高光束质量的1 064 nm固体激光器或光纤激光器泵浦基于掺氧化镁的周期极化铌酸锂晶体（PPMgLN）的光学参量振荡器的中波红外激光器方案,其波段转换效率可达到16%以上。     

Efficient single mode operation of a CW ring dye laser with a Mach-Zehnder interferometer

Stable single mode operation of a ring dye laser is obtained with the combination of a Mach-Zehnder interferometer (MZI), three plate birefringent filter, a single thin etalon and a unidirectional diode. The MZI eliminates the fractional insertion loss due to beam walk-off and distortion which an intracavity etalon must introduce in order to select single frequency operation. We experimentally demonstrate the low insertion loss, single mode stability and frequency tuning of a ring dye laser using a specially designed, compact MZI. Finally, we propose MZIs with no coatings, which should permit extremely low loss broadband operation.     

微流芯片中消逝波激励的荧光辐射特性研究

将石英裸光纤植入聚二甲基硅氧烷基片的微流道中,采用沿光纤轴向光抽运、消逝场激励染料分子的方式,在基片微流道中获得均匀的荧光辐射.实验发现,荧光辐射的强度随光纤轴向距离的增加而衰减,光纤包层溶液折射率越大,荧光沿光纤轴向的衰减越突出;包层溶液中染料浓度越大,荧光沿光纤轴向的衰减也越突出;通过选择适当的包层溶液折射率以及染料浓度可以获得沿光纤轴向接近均匀的荧光辐射.用消逝波激励荧光的辐射理论计算了荧光光强沿光纤轴向的变化,计算结果与实验符合较好.在此基础上,设计并制作了一种具有三个通道的聚二甲基硅氧烷基片,通过在三个微流道中分别注入染料浓度均为0.1 mmol的罗丹明640、罗丹明B及罗丹明6 G的乙醇染料溶液,采用沿光纤轴向消逝波光激励方式,在一块聚二甲基硅氧烷基片上同时实现了三个不同波段的荧光辐射.     

Near infrared,tunable, oxazine 750 perchlorate,synchronously-pumped picosecond ring dye laser

We report the operation and performance of a near-infrared, synchronously-pumped mode locked dye laser, pumped with the 647.1 nm line of a mode locked krypton ion laser. The output pulses are as short as 3.2 ps in duration, and can be tuned from 750 to 910 nm with an intercavity three plate birefringent filter.     

Small-stokes-shift frequency conversion in single-mode birefringent fibers

We report experimental observation of nondegenerate four-photon mixing (FPM) via a new phase-matched process in birefringent fibers. This phase-matching process is characterized by relatively long coherence lengths, and by small pump-to-Stokes frequency shifts (of the order of 100 cm^-1 in high birefringence fibers) that are directly proportional to the fiber birefringence. Pump-to-Stokes energy conversion efficiencies of over 40 percent have been obtained with moderate pump powers (≈1 kW) from a visible cw mode-locked dye laser coupled into single-mode polarization-preserving high-birefringence fibers of a few meters length. In addition, we report the first observation of a totally non-degenerate phase-matched four-photon process in a fiber; this invokes mixing of the original FPM Stokes component with the pump and stimulated Raman radiation.     

Efficient violet upconversion signal from a fluoride fiber doped with erbium

When an erbium-doped fluoride fiber was pumped with a red dye laser beam that resonantly excites the (4)F(9/2) state, we detected efficient violet upconversion emission from the (2)P(3/2) state that is much stronger than the green upconversion emission from the (4)S(3/2) state. Such unusual violet emission was found to be due to a three-photon excitation process.     

Theoretical and experimental investigations of nanosecond 177.3 nm deep-ultraviolet light by second harmonic generation in KBBF

We have presented theoretical and experimental investigations of nanosecond (ns) deep-ultraviolet (DUV) 177.3 nm radiation by means of second harmonic generation (SHG) from a frequency-tripled Nd:YAG laser (355 nm, 49 ns and 10 kHz) in KBe₂BO₃F₂ (KBBF) nonlinear crystal for the first time. A DUV KBBF-SHG numerical model, accounting for linear absorption, pump depletion, beam spatial birefringent walk-off and diffraction, is performed in the Gaussian approximation of spatial and temporal profiles. In the experiment, a maximum average output power of 14.1 mW at 177.3 nm was obtained. The dependence of 177.3 nm output power on the 355 nm pump power was simulated. The calculated results are in good agreement with the measured data. We used the model further to investigate the optical conversion efficiency, pulse width, beam spatial intensity profile and beam quality factor of the generated 177.3 nm light, in particular the effect of beam birefringent walk-off.     

消逝波激励的双波段光纤回音壁模式激光辐射

将石英光纤浸入低折射率的染料溶液中后构成圆柱形微腔.采用轴向光抽运消逝波激励激光增益的方式,使增益区域局限在圆柱形微腔回音壁模式的模场区域内,由此显著地提高了抽运效率,增加了沿光纤轴向的增益长度.在一根石英光纤的轴向分段填入浓度同为2×10^-3mol/L的罗丹明6G和罗丹明B乙醇溶液,在567—576nm 和592—600nm的两个波长范围内同时获得回音壁模式的激光辐射;分段填入浓度为8×10^-4和8×10^-3mol/L的罗丹明B乙醇溶液, 关键词： 消逝波激励 圆柱形微腔 回音壁模式 双波段激光辐射     

Compact sub-nanosecond wideband laser source for biological applications

We report on the experimental demonstration of a supercontinuum generation in a highly birefringent nonlinear microstructured optical fiber by use of a sub-nanosecond passively Q-switched Yb-doped double-clad fiber laser. The powerful, low-cost sub-nanosecond pulses produced by the fiber laser source permit one to generate a flat supercontinuum between 1064 and 1600 nm and a more structured spectral broadening down to 400 nm is also initiated. PACS 42.65.Wi; 42.55.Wd     

Dual-wavelength high-power Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating

We report a high-power dual-wavelength Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating (FMFBG). The FMFBG was fabricated by using a piece of fiber in a length of fiber with a cutoff wavelength of 1225 nm, which supported two modes at 1060 nm. The laser was pumped by a fiber pigtailed laser diode working at 915 nm. Single-wavelength, dual-wavelength and triple-wavelength laser oscillations were observed when the fiber laser operated under different low pump powers. However, stable dual-wavelength operation was achieved at higher pump power of 3.9 W and remained unchanged until the output power reached 5.67 W under the maximum available pump power of 10.7 W. The laser wavelengths were centered at 1059.12 and 1060.80 nm with a full-width at half-maximum of 37 and 43 pm, respectively. The signal-to-noise-ratio was greater than 50 dB and the beam quality factor (M²) was about 1.9.     

First observation of a resonance ionization signal on242mAm fission isomers

The feasibility of a hyperfine spectroscopy on^242mAm fission isomers has been demonstrated at the low target production rate of 10/s. The experimental method employed is based on resonance ionization spectroscopy in a buffer gas cell with detection of the ionization process by means of the fission decay of the isomers. The resonance ionization has been performed in two steps, utilizing an excimer dye laser combination with a repetition rate of 300 Hz. The first resonant step proceeds through theJ=7/2 term at 21440.35 cm⁻¹, which has been excited with the tuncable dye laser beam of a wavelength of 466.28 nm, the second non-resonant step is achieved with the 351 nm radiation of the excimer laser itself, running with XeF. The frequency scan of the tuneable dye laser exhibits a broad resonance ionization signal, the width of which is most likely explained by the magnetic hyperfine interaction.     

Fabrication of a quartz optical fiber tip for dental treatment with Nd:YAG laser—Proposal of a new process with TiO2 powder

In dental treatment with Nd:YAG laser beam, a quartz optical fiber is generally used to transmit the laser beam, which is irradiated to the hard and soft tissues for a caries treatment and a periodontal tissue excision. Since a normal optical fiber, which the laser beam comes out from the tip of the fiber, has difficulty irradiating to a narrow space and an inner root canal uniformly, it is effective to use a processed optical fiber tip from which is obtained a diffused and circumferential laser beam. In this paper, a new process to obtain these laser beams with TiO₂ powder is proposed, and the characteristics and the performances of the processed optical fiber were investigated. An experimental instrument was developed to measure the energy partition radiated from the processed fiber tip, and the ratio of a straight beam, a sideways beam and heat generated by the absorption of the laser beam was measured in each condition. As a result, the ratio of an energy partition was controllable by changing the incidence parameter to process the fiber tip, and the processed fiber tip corresponding to the clinical purpose could be obtained. The parameters which affected the processability of the fiber tip were processing time and incidence laser energy. The prepared cavity with processed fiber on the enamel was influenced by a straight beam, and the removal of enamel to the depth direction was controllable by using the processed fiber.     

用大芯径石英玻璃光纤传输兆瓦级高能激光脉冲及其在双波长LA-LIBS技术中的应用

为了解决单脉冲激光诱导击穿光谱(LIBS)技术在元素分析时空间分辨本领与分析灵敏度之间的矛盾,本文利用一台双波长输出的Nd∶YAG激光器开展了双波长激光剥离-激光诱导击穿光谱(LA-LIBS)技术的研究。其中532 nm的二倍频激光用于剥离样品;1 064 nm的基频激光通过大芯径石英玻璃光纤传输并实现一定的延时后用于击穿被剥离的样品。两束激光采用正交几何配置以实现高空间分辨高灵敏的元素分析。实验研究了1 064 nm激光到光纤的耦合、光纤输出后的准直以及再聚焦时的一些关键技术问题。研究并得出了四种不同光纤对激光能量的传输能力。选择利用芯径为800 μm,数值孔径为0.39、长50 m的石英玻璃光纤成功传输了15 mJ的调Q激光脉冲并实现了250 ns的延时。并在此基础上开展了铜合金样品的双波长LA-LIBS分析,实验验证了基于一台Nd∶YAG激光器开展双波长LA-LIBS研究的可行性。该技术只需要一台激光器就可以完成相应的光谱分析,具有系统结构简单,便于小型化等优点,适合对不同样品开展原位的高空间分辨高灵敏的元素显微分析。     

用不同强度皮秒脉冲相关技术测量甲酚紫吸收恢复时间

以Ar+离子锁模激光器同步泵浦R6G染料激光器作光源,用不同强度皮秒脉冲相关的泵涌—探测技术测得甲酚紫甲醇溶液的吸收恢复时间为162±3.5ps.并且用三能级模型对这一动力学过程进行了理论分析.     

Self-grown fiber fabrication by two-photon photopolymerization

We demonstrate a new fiber growth mechanism in a photocurable resin by ultrafast laser illumination. A high-repetition rate (∼1 MHz) ultrafast laser beam at the wavelength of ∼523 nm was focused into an ultraviolet photocurable resin to trigger two-photon photopolymerization process. Time-resolved shadowgraphs and scattered light imaging revealed that the curing commenced in the neighborhood of the geometric focal point of the laser beam and that the fiber growth progressed mostly towards the laser source. The cured fiber was thinner and longer than the profile of the focused laser beam, facilitated by nonlinear propagation and absorption of the ultra-fast laser beam. The achieved aspect ratio of the fiber was higher than 180 with ∼10 μm mean diameter, and the average growth rate was up to ∼2 mm/s.     

高功率光纤激光的时间部分相干性对相干合成的影响

 将多个光纤激光器的输出光束进行相干合成是获得高功率、高光束质量激光的有效途径。利用准部分相干光(PPCB)模型,计算了高功率光纤激光器阵列发出的部分相干光在远场的能量分布,分析了激光的时间部分相干性对相干合成的影响。计算结果表明,随着单根激光器输出光束线宽的增大,远场光斑的图样基本保持不变,但峰值功率和Strehl比随之减小。对于采用的算例,要保证远场光斑的Strehl比大于0.8,单根光纤激光器的线宽不能超过5 nm。     

Fiber ring laser employing an all-polarization-maintaining loop periodic filter

A novel erbium-doped fiber ring laser employing an all-polarization-maintaining fiber birefringent loop as a periodic filter is proposed and demonstrated. The laser using 1 nm interval filter generates four wavelengths with equal frequency spacing without using any techniques to overcome the homogeneous line broadening of the gain medium at room temperature. Room-temperature operation of dual-wavelengths with 0.56 nm spacing has also been realized.