电感耦合等离子体质谱测试硫化物中的微量元素

采用多种酸组合消解方法消解硫化物样品,最终选取A:HNO3密闭消解法;B:HCI+HF与HNO3两步消解法对硫化物标准物质GBW07267(黄铁矿)、GBW07268(黄铜矿),GBW07270(闪锌矿)及硫化物标准物质WMS-1a(块状硫化物)样品进行消解,采用ICP-MS测试了39种微量元素.结果表明,HNO3密闭...     

落叶松与白桦树中微量及稀土元素的ICP-MS检测方法研究

利用微波消解法处理植物灰分样品,讨论了混合酸组成、混酸配比、固液比和微波消解时间对样品制备结果的影响.优选微波消解方案:微波压力(MPa)0.5、1.0、1.5、2.0,消解时间(min)4、3、3、10的微波程序,混合酸体系HNO3-HCl-HF-HClO4(体积比为6 ∶ 2 ∶ 1 ∶ 1).在此条件下, 进行了方法准确度实验和测量结果重复性实验, 该方法经植物国家标准物质(GBW07603)验证,微量元素测试结果的相对误差为1.06% ～5.60%,相对标准偏差为0.87% ～5.25%;稀土元素测试结果的相对误差为1.82% ～10.2%,相对标准偏差为2.14% ～8.00%.应用电感耦合等离子体质谱法(ICP-MS)同时测定植物灰分中21种微量元素和15种稀土元素.结果表明, 微波消解法处理植物灰分样品, 具有快速、简便、节省试剂、消解完全等特点, 测定结果的准确度和精密度令人满意.     

微波消解-电感耦合等离子体质谱法检测土壤中16种稀土元素

建立了微波消解-电感耦合等离子体质谱法(ICP-MS)测定土壤样品中16种稀土元素的分析方法。样品经硝酸-过氧化氢-氢氟酸消解,直接用ICP-MS测定试液中16种稀土元素。研究了ng/mL水平的Ba氧化物及轻稀土氧化物对重稀土元素的干扰程度,其中Ba和Pr的氧化物干扰较严重,不过此类干扰可通过Method编辑干扰方程得以校正。测定土壤标准物质GBW07446及GBW07451,结果与标准物质证书值一致。     

微波消解-电感耦合等离子体质谱(ICP-MS)法同时测定紫菜中16种稀土元素

以农贸市场和超市的紫菜为样品,经过微波消解,利用电感耦合等离子体质谱(ICP-MS)法对紫菜中16种稀土元素进行同时测定。通过在线引入内标溶液,在0~2.00μg/L范围内检测信号(CPS)与稀土元素含量之间呈现良好的线性关系,相关系数R2均大于0.999 9,相对标准偏差(RSD)小于3.3%。用来测定国家标准物质GBW10052(GSB-30)和GBW10045中的稀土元素,所得结果与标准值基本一致,从而建立了一种快速、准确测定紫菜中痕量稀土元素的方法。     

微波消解样品-电感耦合等离子体质谱法测定植物灰分中微量元素

应用电感耦合等离子体质谱法(ICP-MS)同时测定植物灰分中21种微量元素和15种稀土元素.用微波消解样品,对微波消解植物灰分样品的条件进行了试验.其优选微波消解条件为:微波压力为2 MPa,消解时间为10 min,以硝酸、盐酸、氢氟酸、高氯酸(体积比为6比2比1比1)的混合酸消解样品,对0.100 0 g植物标准物质(GBW 07603)进行10次平行测定,微量元素测定结果的相对标准偏差(n=10)在0.87%～5.96%之间,稀土元素测定结果的相对标准偏差(n=10)在2.14%～8.00%之间.     

电感耦合等离子体质谱法测定花生中稀土元素

本文建立了微波消解-八极杆碰撞/反应池(ORS)电感耦合等离子体质谱法(ICP-MS)同时测定花生仁中的La、Ce、Pr、Nd、Sm、Eu、Gd、Tb、Dy、Ho、Er、Tm、Yb、Lu 14种稀土元素的分析方法。样品经微波消解后,在线加入103 Rh内标元素有效消除了非质谱干扰,选用八极杆碰撞/反应池技术有效地消除了质谱干扰。氦碰撞反应气流速为4.5mL/min时背景等效浓度(BEC)最低。结果表明,选择体积比4∶1的HNO3-H2O2体系微波消解充分,14种稀土元素的检出限小于0.0011ng/mL,相对标准偏差(RSD)低于2.60%。该方法具有简单、快速、准确的特点,可作为花生中稀土元素同时测定的可靠方法。     

微波消解-电感耦合等离子体质谱法测定人面果树中的重金属元素

建立了微波消解-电感耦合等离子体质谱(ICP-MS)法测定人面果树中As,Cr,Cd,Pb,Ni,Se,Hg 7种重金属元素含量的方法。样品采用HNO3-H2O2消解体系,避免了赶酸的操作,经微波消解后,用电感耦合等离子体质谱(ICP-MS)测定样品中As,Cr,Cd,Pb,Ni,Se,Hg 7种重金属元素的含量。方法对7种元素的校准曲线的相关系数r>0.9997,检出限在0.0098～0.0874μg/L之间,回收率在93%～115%之间,RSD在0.41%～4.9%。     

一体化碰撞反应(iCRC)-电感耦合等离子体质谱(ICP-MS)法测定地质样品中痕量稀土元素

钡以及轻稀土元素氧化物对中、重稀土元素的干扰一直是质谱测试中存在的问题。建立了石墨粉垫底碳酸钠-硼酸混合熔剂熔融前处理样品,以103 Rh为内标校正,一体化碰撞反应-电感耦合等离子体质谱(ICP-MS)法测定地质样品中稀土元素含量的方法。探讨了碳酸钠-硼酸混合熔剂熔融前处理样品注意事项、碰撞模式下碰撞气流量和离子透镜的参数优化、干扰校正实验等问题,采用国家标准物质GBW07403、GBW07405、GBW07427、GBW07429验证,实验结果表明,各元素线性关系良好,相关系数均大于0.999,方法检出限在0.01～0.03mg/kg,相对误差为0.13%～7.1%,相对标准偏差为0.79%～6.6%,测定结果与标准值相吻合。对实际样品分析,得到平滑的球粒陨石归一化的稀土元素配分曲线,证明测定结果是合理可信的。方法熔剂用量少,过程空白低,对器皿的侵蚀小,直接加热浸取,简化了操作过程,适用于大批量地质样品中稀土元素的测定。     

微波/电热板组合消解-电感耦合等离子体质谱(ICP-MS)法测定土壤中重金属元素

为提高土壤检测的重金属得率,采用了微波消解/电热板组合预处理-电感耦合等离子体质谱法(ICP-MS)测定土壤重金属含量。分析了硝酸(HNO3)、氢氟酸(HF)、高氯酸(HClO4)和盐酸(HCl)组合消解液及赶酸温度对土壤预处理影响。结果显示：在硝酸和盐酸混合消解液中,硝酸占比越高,铬(Cr)、钴(Co)、铜(Cu)、镉(Cd)得率更高;消解液体系中加入氢氟酸可使消解更加彻底,提高铬与铜的得率。最优预处理消解条件为硝酸 6ml+ 氢氟酸 2ml消解液组合进行微波消解,1ml 高氯酸于155℃电热板上赶酸。经土壤标准样品GBW07401(GSS-1)和GBW07452(GSS-23)实际应用,预处理条件优化后测试准确度和稳定性均显著提高。此外使用元素铑(Rh)作为内标物时,其方法稳定性和准确性高于内标物钪(Sc)和锗(Ge)。可为相关国家土壤重金属测定标准的修制订提供方法学参考。     

微波消解-电感耦合等离子体质谱法同时测定铝土矿中11种金属元素

建立了微波消解-电感耦合等离子体质谱法(ICP-MS)同时测定铝土矿中锂、铬、铜、铁、钛、钾、钠、钙、镁、铅、锌等11种金属元素含量的方法。将铝土矿粉碎、研磨和干燥后,取0.1 g样品,加入3 mL硫酸、1 mL硝酸、2 mL氢氟酸和3 mL盐酸,按升温程序微波消解样品,加40 g·L~(-1)硼酸溶液10 mL,继续在120℃下消解10 min,使消解液变澄清。冷却后取出,180℃加热至近干,用1%(体积分数)硝酸溶液稀释,按照ICP-MS条件测定。通过用10 g·L~(-1)铝基体溶液配制混合标准溶液系列并加入内标元素Sc、Ge、Bi的方法来消除基体干扰,选择合适的待测元素同位素的方法来消除谱线重叠干扰。结果显示:11种元素的质量浓度均在一定范围内与其对应的响应值与内标元素响应值的比值呈线性关系,检出限(3s)为0.011～1.400 mg·kg~(-1)。对实际样品进行加标回收试验,测定值为0.13～72.21 mg·L~(-1),测定值的相对标准偏差(n=6)为0.69%～2.6%,回收率为94.0%～106%;此方法用于分析3种铝土矿成分分析标准物质GBW 07177、GBW 07179、GBW 07180,所得测定值均在认定值要求的范围内。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.     

Knoevenagel condensation catalyzed by novel Nmm-based ionic liquids in water

A series of novel N-methyl morpholine (Nmm) based ionic liquids with 1,2-propanediol group were synthesized and used as catalysts for Knoevenagel condensation at room temperature in water. Under the effect of the catalyst, various aldehydes or aliphatic ketones could react with a wide range of activated methylene compounds well, including malononitrile, alkyl cyanoacetate, cyanoacetamide, β-diketone, barbituric acid, 2-arylacetonitrile and thiazolidinedione. Furthermore, most of the products could be separated just by filtrating and washing with water. Additionally, the catalyst is recyclable and applicable for the large-scale synthesis.     

Construction of polyheterocyclic spirotetrahydrothiophene derivatives via sulfa-Michael/aldol cascade reaction

A series of polyheterocyclic spirotetrahydrothiophene derivatives were obtained in moderate to excellent yields via a catalyst-free sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 under mild conditions. We also present the first asymmetric sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 with moderate to good enantioselectivities catalyzed by readily available chiral phase-transfer catalysts (PTCs).     

Suzuki-Miyaura reactions of the soluble guanylate cyclase inhibitor NS2028: a non-product specific route to C-8 substituted analogues

Both soluble guanylate cyclase (sGC) inhibitors ODQ 1 and NS2028 2 are synthesized via improved protocols. In the former case treating 3,4-dihydroquinoxalin-2(1H)-one oxime 8, which can be prepared in two steps from 1,2-benzenediamine, with 1,1′-carbonyldiimidazole (CDI) gives the dihydro-ODQ 10 that in the presence of KMnO₄ oxidises to give ODQ 1 in an overall yield of 46% starting from 1,2-benzenediamine. In the latter case, the synthesis affords NS2028 2 from 2-amino-4-bromophenol 3 in three steps with an overall yield of 85% and avoids the need for chromatography. Furthermore, Suzuki-Miyaura reaction conditions are described that enable the preparation of 8-aryl and 8-heteroaryl derivatives of NS2028 directly from NS2028 2. Finally, demethylation of the 8-(methoxyphenyl) substituted analogues afforded the 8-(hydroxyphenyl) derivatives 40-42. All new products are fully characterised.