Transport of water in polyvinyl alcohol films: Effect of thermal treatment and chemical crosslinking

Data on sorption and transport of water in polyvinyl alcohol films, modified by thermal treatment above T_g, or by chemical crosslinking with glutaraldehyde at different crosslinking degrees, are presented. Equilibrium swelling is constrained by both treatments, except for low degrees of crosslinking where the said reduction is counterbalanced by the partial loss of crystallinity. Analysis of the resulting water uptake kinetics indicates that viscous relaxation effects are, at least partly, responsible for the observed non-Fickian kinetic behavior. Thermodynamic diffusion coefficients of water, D_W, and relaxation frequencies of the swelling polymer, β_W, are determined by application of a theoretical model accounting for relaxation-dependent sorption kinetics in glassy polymers. The results indicate that the effect of both heat-treatment and chemical crosslinking is more intense on the macromolecular relaxation process than on the diffusion coefficient of water. Comparison of the release kinetics of a model drug from as-prepared, non-crosslinked and from crosslinked matrices indicate that the retardation of macromolecular relaxations process induced by crosslinking results in a more uniform release rate.     

Release properties of chemical and enzymatic crosslinked gelatin-gum Arabic microparticles containing a fluorescent probe plus vetiver essential oil

Oil-containing gelatin-gum Arabic microparticles were prepared by complex coacervation followed by crosslinking with glutaraldehyde or transglutaminase. A fluorescent mixture, khusimyl dansylate (KD) as the fluorescent compound mixed to the vetiver essential oil, was used as oil model. The effect of the type of crosslinking of the coacervated gelatin-gum Arabic membrane, the physical state of microparticles, wet or freeze-dried and the type of release media, aqueous with surfactants, Sodium Dodecyl Sulphate (sds) or Tween 80 (tw) and anhydrous ethanol as organic media on the release rate of the KD from the microparticles, was experimentally investigated.It was shown that the oil was dispersed uniformly throughout the microparticles and the chemical crosslinked microparticles were more resistant to swelling, presenting smaller sizes after hydration. Also the crosslinking effect, transglutaminase or glutaraldehyde, could be confirmed by the integrity of the crosslinked gelatin-gum Arabic microparticles after incubation in the aqueous sds media, compared to complete dissolution of the uncrosslinked microparticles in this media.The cumulative fluorescent KD release from the gelatin-gum Arabic microparticles decreased in the following order of dissolution media: anhydrous ethanol > tw > sds and the wet microparticles have shown a faster KD release than freeze-dried ones. A mathematical model was used to estimate the diffusion coefficient (D). The chemically crosslinked gelatin-gum Arabic microparticles ensured a pronounced retard effect in the KD diffusion, presenting a D varying from 0.02 to 0.6 × 10⁻¹¹ cm²/s, mainly in an aqueous media, against D varying from 1.05 to 13.9 × 10⁻¹¹ cm²/s from the enzymatic crosslinked microparticles.     

The swelling interface number as a criterion for prediction of diffusional solute release mechanisms in swellable polymers

When a glassy polymer containing a uniformly dispersed solute is brought in contact with a penetrant, solute diffusion will be associated with the transport mechanism and penetration velocity of the penetrant in the polymer. Analysis and prediction of mechanisms of diffusional solute release may be obtained through a new dimensionless number, the swelling interface number, Sw, which compares the relative mobilities of the penetrant and the solute in the presence of macromolecular relaxations in the polymer. It is shown that a sufficient and necessary criterion for time-independent diffusional solute release rates from these swellable systems is that the Sw be smaller than 10^?2. The swelling interface number Sw may be related to easily determined structural and thermodynamic parameters of the solute/polymer/penetrant system. Preliminary experimental results of dynamic water swelling of poly(2-hydroxyethyl methacrylate-co-methyl methacrylate) and diffusional release of theophylline from initially glassy copolymers show that decreasing values of Sw are related to increased pseudo-case-II transport kinetics of the solute.     

Understanding the effect of skin formation on the removal of solvents from semicrystalline polymers

The effect of glassy skin formation on the drying of semicrystalline polymers was investigated with a comprehensive mathematical model developed for multicomponent systems. Polymers with high glass‐transition temperatures can become rubbery at room temperature under the influence of solvents. As the solvents are removed from the polymer, a glassy skin can form and continue to develop. The model takes into account the effects of diffusion‐induced polymer crystallization as well as glassy–rubbery transitions on the overall solvent content and polymer crystallinity. A Vrentas–Duda free‐volume‐based diffusion scheme and crystallization kinetics were used in our model. The polymer–solvent system chosen was a poly(vinyl alcohol) (PVA)–water–methanol system. The drying kinetics of PVA films were obtained by gravimetric methods with swollen films with known water/methanol concentrations. The overall drying behaviors of the polymer system determined by our model and experimental methods were compared and found to match well. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3191–3204, 2005     

Adhesion of high polymers. I. Influence of diffusion,adsorption, and physical state on polymer adhesion

It is possible to identify three distinct types of polymer adhesion on the basis of the physical state of adhesive and adherend: (1) rubbery polymer–rubbery polymer (R–R adhesion); (2) rubbery polymer–glassy polymer (R–G adhesion); (3) rubbery polymer–nonpolymer (R–S adhesion). Limitations of the diffusion and adsorption theories and their conflicting results are discussed within the framework of the proposed classification. By defining the physical state of the polymer as an adhesive or as an adherend, it is possible to eliminate many of the discrepancies commonly noted in attempted application of the diffusion and adsorption theories. As predicted by the Bueche-Cashin-Debye equation, the diffusion of a polymer into another should be greatly reduced as it changes from the rubbery to the glassy state. For this reason, diffusion, which depends to a great extent on the physical state of the polymer, is actually a limited, selective process. Assuming a 10¹³ poise bulk viscosity at glass temperature, self-diffusion constants of forty polymers were calculated to be 10^?21cm.²/sec. or 10^?5A.²/sec. This slow rate of diffusion is unmeasurable and insignificant. Adsorption, which is less dependent on the physical state of the polymer, is more frequently encountered.     

The controlled release behavior and pH‐ and thermo‐sensitivity of alginate/poly(vinyl alcohol) blended hydrogels

Poly(vinyl alcohol) (PVA) was blended with sodium alginate (Alg) in various ratios and crosslinked with calcium chloride and made into hydrogel membranes. The dependence of the swelling behavior of these Alg‐Ca/PVA hydrogels on pH was investigated. The temperature‐dependent swelling behavior of the semi‐interpenetrating network (semi‐IPN) hydrogels was examined at temperatures from 2 to 45°C and the enthalpy of mixing (ΔH_mix) was determined at various temperatures. The molecular structure of the hydrogels was studied by infrared spectroscopy and their water structure in the semi‐IPN hydrogels was measured by differential scanning calorimetry (DSC). The influence of Ca²⁺ content on the network structure of Alg‐Ca/PVA hydrogels was investigated in terms of the compressive elastic modulus, effective crosslinking density, and the polymer–solvent interaction parameter based on the Flory theory. The loading of alizarin red S (ARS) followed the Langmuir isotherm mechanism and the release kinetics of ARS from the Alg‐Ca/PVA hydrogels followed the Fickian diffusion mechanism. Copyright © 2008 John Wiley & Sons, Ltd.     

Radiation-induced crosslinking of polyvinyltrimethylsilane in the presence of ethylene glycol dimethacrylate and allyl methacrylate

Radiation-induced crosslinking of homogeneous glassy polyvinyltrimethylsilane was carried out either by the γ-irradiation of the polymeric films containing 3–20 wt% of ethylene glycol dimethacrylate or by the radiation-induced grafting of allyl methacrylate from vapour phase onto films made of pure polymer. The dependence of grafting value on the absorbed γ-irradiation dose and film thickness was investigated. The modified films were analyzed for the sol/gel content and the dependence of gel fraction yield of crosslinked polymer on absorbed dose, concentration of the crosslinking agents and film thickness.The radiation-chemical yields of crosslinking and degradation as well as gelation doses were calculated. The permeability of oxygen and nitrogen through the crosslinked films was determined.     

Dynamics of cyclodimerization and viscoelasticity of photo‐crosslinkable PVA

We investigated the interfacial properties of poly(vinyl alcohol) carrying UV‐crosslinkable pendant quaternized stilbazole (styrylpyridinium), PVA‐SbQ. The extent and dynamics of PVA‐SbQ cyclodimerization reactions and crosslinking induced by UV irradiation were monitored in situ and in real time by quartz crystal microgravimetry (QCM). Sensograms reflecting time‐dependent changes in density and viscoelasticity of crosslinking films followed a Boltzmann sigmoidal model, depending on precursor film composition and irradiation power. The shifts in QCM frequency and energy dissipation upon PVA‐SbQ cyclodimerization correlated with three photo‐crosslinking phases involving soft‐to‐rigid transitions, namely, induction (initiation), main crosslinking (interaction), and termination. PVA‐SbQ films crosslinked to different degree were used as protein carriers and a slower release profile was determined for the films that underwent more extensive crosslinking. Overall, this study demonstrates for the first time the dynamics of PVA‐SbQ crosslinking and its impact in system viscoelasticity and protein release. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 345–355     

Immobilized Laccase on Activated Poly(Vinyl Alcohol) Microspheres For Enzyme Thermistor Application

Poly(vinyl alcohol) (PVA) microspheres were prepared by inverse suspension crosslinked method, with glutaraldehyde as a crosslinking agent. PVA microspheres activated with aldehyde groups were employed for Trametes versicolor laccase immobilization. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy were used to characterize the activated PVA microspheres and PVA microspheres with immobilized laccase (Lac/PVA microspheres), which show that laccase was successfully immobilized on the PVA microspheres. The optimum pH and temperature coupling conditions for the immobilized laccase were determined to be 3.3 and 30 °C, respectively. Residual activity was also investigated by soaking the immobilized laccase in organic solvents at different concentrations, proving it chemically stable. Immobilized laccase exhibited good storage stability at 4 °C. The enzyme biosensor showed good performance in 2,2-azinobis(3-ethylthiazoline-6-sulfonate) and bisphenol A, with concentration ranges of 2 to 8 mM and 0.05 to 0.25 mM, respectively. Therefore, PVA microspheres may have high potential as support for enzyme thermistor applications.     

Measurement of the infinite dilution diffusion coefficients of small molecule solvents in silicone rubber by inverse gas chromatography

The infinite dilution diffusion coefficients of n-hexane, n-heptane and n-decane in crosslinked silicone rubber with different crosslinking agent concentrations were measured in the temperature range of 348.15 K-368.15 K by inverse gas chromatography. The crosslinked silicone rubber was obtained by dissolving PDMS prepolymer, crosslinking agent and catalyst in n-heptane solvent and characterized by FTIR spectra. The Van Deemter equation was used to determine diffusion coefficients from the variation in chromatographic peak width with carrier gas flow rate. The good linear relation indicated the Van Deemter equation used in this work was reliable. The influences of small molecule solvent, crosslinking agent concentration and temperature on the infinite dilution diffusion coefficient were investigated. The results showed that the infinite dilution diffusion coefficient decreased with an increasing number of CH₂ group in the alkane series. The increase in crosslinking agent concentration resulted in decrease of the infinite dilution diffusion coefficient. The infinite dilution diffusion coefficient increased with the rising of temperature. The interdependence on the infinite dilution diffusion coefficient and temperature accorded with Arrhenius equation well. Diffusion constant and activation energy obtained from the Arrhenius equation provided straight lines with the specific critical volume and crosslinking agent concentration.     

Crosslinking of hyaluronic acid with glutaraldehyde

Hyaluronic acid (HA) was chemically crosslinked with glutaraldehyde (GA) to produce water-insoluble films having low water contents when brought into contact with water. The crosslinking reaction was performed using uncrosslinked HA films in acetone–water mixtures. This method could produce water-insoluble HA films with water contents as low as 60 wt % when subjected to swelling with phosphate-buffered saline of pH 7.4 at 37°C. This 60 wt % water content was lower than any values for HA ever reported. There was an optimal HCl concentration around 0.01N for the HA crosslinking with GA in acetone—water mixtures. To get information on the crosslinking mechanism, alginic acid, which possesses hydroxyl and carboxyl groups in one molecule, similar to HA, and poly(vinyl alcohol) (PVA) and amylopectin, which possess only hydroxyl groups, were subjected to crosslinking with GA. PVA and amylopectin were also found to become water-insoluble after reaction with GA. On the basis of the infrared spectra of these crosslinked films, it was concluded that intermolecular formation of hemiacetal bonds with GA between the hydroxyl groups belonging to different HA molecules led to crosslinking. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3553–3559, 1997     

Effect of Crosslinking Agent on Neem (Azadirachta Indica A. Juss.) Seed Oil (NSO) Encapsulated Microcapsules of κ -Carrageenan and Chitosan Polyelectrolyte Complex

Microencapsulation of neem (Azadirachta Indica A. Juss.) seed oil (NSO) was carried out by polyelectrolyte complexation of κ -carrageenan and chitosan. The microcapsules were crosslinked by using three different crosslinking agents - glutaraldehyde, genipin and tannic acid. The lowest and highest water uptake capacities were exhibited by glutaraldehyde and tannic acid crosslinked matrices, respectively. The release behavior of NSO from encapsulated crosslinked microcapsules followed the order: tannic acid > genipin > glutaraldehyde. Polyelectrolyte complex formation and its interaction with crosslinker was studied. Crosslinking improved thermal stability without affecting crystallinity. Roughness appeared on microcapsule's surface indicated interaction between microcapsules and crosslinker.     

Pervaporation separation of water-acetic acid mixtures through poly(vinyl alcohol) membranes crosslinked with glutaraldehyde

Poly(vinyl alcohol) (PVA) membranes crosslinked with glutaraldehyde (GA) were prepared by a solution method for the pervaporation separation of acetic acid-water mixtures. In the solution method, dry PVA films were crosslinked by immersion for 2 days at 40°C in reaction solutions which contained different contents of GA, acetone and a catalyst, HCl. In order to fabricate the crosslinked PVA membranes which were stable in aqueous solutions, acetone was used as reaction medium in stead of aqueous inorganic salt solutions which have been commonly used in reaction solution for PVA crosslinking reaction. The crosslinking reaction between the hydroxyl group of PVA and the aldehyde group of GA was characterized by IR spectroscopy. Swelling measurements were carried out in both water and acetic acid to investigate the swelling behavior of the membranes. The swelling behaviour of a membrane fabricated at different GA content in a reaction solution was dependent on crosslinking density and chemical functional groups created as a result of the reaction between PVA and GA, such as the acetal group, ether linkage and unreacted pendent aldehydes in PVA. The pervaporation separation of acetic acid-water mixtures was performed over a range of 70–90 wt% acetic acid in the feed at temperatures varying from 35 to 50°C to examine the separation performances of the PVA membranes. Permeation behaviour through the membranes was analyzed by using pervaporation activation energies which had been calculated from the Arrhenius plots of permeation rates.     

Dynamic mechanical analysis

Using dynamic mechanical analysis (DMA) we have studied thermal degradation for a system containing a diglycidyl ether of bisphenol A (DGEBA) and 1,3-bisaminomethylcylohexane (1,3-BAC). The changes of dynamic mechanical properties during thermal degradation indicated a shift of the glass transition temperature (T _g) to higher temperatures and a decrease in the peak value of the dynamic loss factor (tan δ) with an increasing of aging time. The value of dynamic storage modulus (E′) at the rubbery state showed an increase with aging time, whiteE′ at the glassy state only underwent a moderate change with increased thermal degradation. From these results it can be argued that thermal degradation during the stage prior to the onset of the severe degradation involves structural changes in the epoxy system, as further crosslinking and loss of dangling chains in the crosslinked network.     

A Water-Soluble Epoxy-Based Green Crosslinking System for Stabilizing PVA Nanofibers

With the ever-growing concern about environmental conservation, green production and water-based nanofibers have attracted more and more interest from both academic and industrial fields; nevertheless, the stabilization process of water-based nanofibers is primarily relying on the application of organic solvent-based crosslinking agents. In this work, we develop a green approach to fabricate water-resistant polyvinyl alcohol (PVA) nanofibers by using a water-based epoxy compound, N¹, N⁶-bis(oxiran-2-ylmethyl) hexane-1,6-diamine (EH), as the crosslinker. This EH/sodium carbonate/sodium bicarbonate (CBS) solution system can break down large aggregates of PVA molecules into small ones and promote the uniform distribution of EH in the solution, resulting in the improved stability of crosslinked PVA nanofibers. We firstly report that the uniform dispersion of crosslinking agents in the electrospinning solution plays a vital role in improving the stability of spinning solutions and the water resistance of crosslinked PVA nanofibers by comparing crosslinking performances between water-based epoxy and conventional water-based blocked isocyanate (BI). This work could open up a novel strategy and green approach for the stabilization of water-based nanofibers.     

Swellable molecularly imprinted polyN-(N-propyl)acrylamide particles for detection of emerging organic contaminants using surface plasmon resonance spectroscopy

Lightly crosslinked theophylline imprinted polyN-(N-propyl)acrylamide particles (ca. 300 nm in diameter) that are designed to swell and shrink as a function of analyte concentration in aqueous media were spin coated onto a gold surface. The nanospheres responded selectively to the targeted analyte due to molecular imprinting. Chemical sensing was based on changes in the refractive index of the imprinted particles that accompanied swelling due to binding of the targeted analyte, which was detected using surface plasmon resonance (SPR) spectroscopy. Because swelling leads to an increase in the percentage of water in the polymer, the refractive index of the polymer nanospheres decreased as the particles swelled. In the presence of aqueous theophylline at concentrations as low as 10⁻⁶ M, particle swelling is both pronounced and readily detectable. The full scale response of the imprinted particles to template occurs in less than 10 min. Swelling is also reversible and independent of the ionic strength of the solution in contact with the polymer. Replicate precision is less than 10⁻⁴ RI units. By comparison, there is no response to caffeine which is similar in structure to theophylline at concentrations as high as 1 × 10⁻² M. Changes in the refractive index of the imprinted polymer particles, as low as 10⁻⁴ RI units could be readily detected. A unique aspect of the prepared particles is the use of light crosslinking rather than heavy crosslinking. This is a significant development as it indicates that heavy crosslinking is not entirely necessary for selectivity in molecular imprinting with polyacrylamides.     

High-resolution solid-state 19F-NMR spectroscopy of the sorption and diffusion of fluorine-containing aromatic molecules in polymeric media

High-resolution ¹⁹F solid-state NMR spectroscopy was employed to study the sorption properties of hexafluorobenzene (HFB) and 3,5-bis (trifluoromethyl) aniline (TFMA) in polystyrene (PS) and butyl rubber (BR). The NMR spectra indicate that the penetrants undergo dual-mode sorption in the glassy polymer (PS), but are highly mobile in the rubbery polymer (BR). In addition, the NMR method was utilized in the experimental determination of diffusion coefficients for the HFB/PS, TFMA/PS, and HFB/BR systems through desorption studies. The diffusion results for the TFMA/PS case agree very well with those previously obtained via resonance nuclear reaction analysis. © 1993 John Wiley & Sons, Inc.     

Stabilization of electrospun poly(vinyl alcohol) nanofibrous mats in aqueous solutions

<正>The stability ofpoly(vinyl alcohol)(PVA) nanofibrous mats in water media was improved by post-electrospinning treatments.Bifunctional glutaraldehyde(GA) in methanol was used as a crosslinking agent to stabilize PVA nanofiber,but fiber twinning was observed frequently,and the highly porous structure of PVA nanofibrous mats was destroyed when the crosslinked fiber was soaked in water.To overcome this shortcoming,chitosan(CS) was introduced into the PVA spinning solution to prepare PVA/CS composite nanofibers.Their treatment in GA/methanol solution could retain the fiber morphology of PVA/CS nanofibers and porous structure of PVA/CS nanofibrous mats even if they were soaked in aqueous solutions for 1 month.Scanning electron microscopy(SEM),X-ray diffraction(XRD),thermal gravimetric analysis(TGA) and differential scanning calorimetry(DSC) were applied to characterize the physicochemical structure and thermal properties of PVA nanofibers.It was found that the water resistance of PVA nanofibrous mats was enhanced because of the improvement of the degree of crosslinking and crystallinity in the electrospun PVA fibers after soaking in GA/methanol solution.     

Effect of DMSO on the sensitivity and diffusion of FPGX gel dosimeter

A stable hydrogel 3D dosimeter was prepared by using Fricke solution, poly (vinyl alcohol) (PVA) and glutaraldehyde (GA). A linear relationship between the dose and the UV absorbency was obtained by determining the color change of the dosimeter in the range of 0–2.5 Gy. Dimethyl sulfoxide (DMSO) was used as a free radical scavenger to analyze the thermo-stability and diffusion of FPGX gel dosimeter systems. The results showed that increasing the DMSO concentration could slow down the color change and the Fe³⁺ diffusion rate in a certain range. With the addition of DMSO, the FPGX gel dosimeter was stable in the storage time before exposure to radiation.     

Solute diffusion in swollen membranes VII. Diffusion in semicrystalline networks

A model is developed to express the solute diffusion coefficient through semicrystalline polymeric networks. The crystallites create impermeable diffusional barriers around the amorphous regions. Solute diffusion is determined by applying a transport model to the amorphous phase and incorporating the crosslinked polymer structure characteristics. This model is tested with theophylline and vitamin B₁₂ permeation experiments through semicrystalline poly(vinyl alcohol) membranes prepared by annealing of amorphous PVA membranes. The degree of crystallinity varies between 23.1 % and 40.5 % on a dry basis. The solute diffusion coefficients correlate well with various parameters of the model.