Liquid chromatographic determination of cetirizine in oral formulations

The development and validation of a reversed-phase liquid chromatographic (LC) method for the determination of cetirizine dihydrochloride in oral formulations are described. An isocratic LC analysis was performed on a reversed-phase C18 column (250 x 4.6 mm id, 5 microm particle size). The mobile phase was 1% orthophosphoric acid solution, pH 3.0-acetonitrile (60 + 40, v/v), pumped at a constant flow rate of 1.0 mL/min. Measurements were made at a wavelength of 232 nm. The calibration curves were linear over the range of 10-30 microg/mL (r2 = 0.9999). The relative standard deviation (RSD) values for intraday precision were 0.94 and 1.43% for tablets and compounded capsules, respectively. The RSD values for interday precision were 0.13 and 0.82% for tablets and compounded capsules, respectively. Recoveries ranged from 97.7 to 101.8% for tablets and from 98.4 to 102% for compounded capsules. No interferences from the excipients were observed. Because of its simplicity and accuracy, the method is suitable for routine quality-control analysis for cetirizine in tablets and compounded capsules.     

A collaborative study: high-pressure liquid chromatographic determination of carbadox and pyrantel tartrate in animal feeds

Carbadox (CBX), an antibacterial agent, and pyrantel tartrate (PT), an anthelmintic, are formulated either separately or together in swine feeds. The official Association of Official Analytical Chemists (AOAC) spectrophotometric methods for both drugs are long, nonspecific, and require standard addition techniques. Results by this technique are positively biased. A simple, direct, specific, high-pressure liquid chromatographic (HPLC) method to determine either one or both drugs simultaneously with apparent accuracy and precision is developed. Drugs are released from feed matrices by water, extracted with dimethylformamide (DMF), cleaned up on alumina, and quantitated by direct comparison to standards using a Whatman Partisil 10 ODS-3 column and a mobile solvent containing 23.5 +/- 1.5% DMF in phosphate buffer (pH 2.0). Fourteen laboratories participated in a collaborative study of this method for determination of CBX and PT in animal feeds.     

Liquid chromatographic determination of fenbendazole residues in pig tissues after treatment with medicated feed.

Fenbendazole (FBZ) is an anthelmintic widely used in farm animals to treat parasitic infestations. In pigs, it is administered in the food. The aim of this study was to validate an analytical method for the determination of FBZ and its metabolites in pig tissues. This method is based on oxidation of FBZ and its sulfoxide metabolite to the sulfone metabolite (FBZSO2). The limit of quantitation for this method is 20 ng FBZSO2/g for all tissues. The maximum residue limits (MRLs) established for FBZ and its metabolites in pig tissues are 50 ng/g for muscle, fat, and kidney and 500 ng/g for liver. This method is based on a liquid-liquid extraction followed by an oxidation with peracetic acid and a cleanup procedure based on 2 liquid-liquid extractions. Determination is achieved by high-performance liquid chromatography with ultraviolet detection. The present method is adjusted to the MRL established for FBZ and its metabolite residues. The analysis of the residues shows that after 72 h posttreatment, no FBZSO2 was detected in muscle, fat, and kidney and that liver levels were below the MRL.     

High-performance liquid chromatographic determination of oxantel and pyrantel pamoate

A method is described for the determination of oxantel and pyrantel pamoate in proprietary broad spectrum anthelmintic tablets. Quantitation is performed by using an octyl Spherisorb column with a mobile phase consisting of acetonitrile and water modified with butylamine. Carbaryl-(1-naphthyl methylcarbamate) is used as internal standard.     

Liquid chromatographic determination of flumetsulam in soybeans

A liquid chromatography (LC) method with UV detection is reported for the determination of the sulfonamide herbicide flumetsulam in soybeans. The ground soybean sample was partitioned between methanol and hexane. The hexane removed the lipids, and the methanol layer containing the analyte was further partitioned between dichloromethane and aqueous phosphate buffer at pH 7.0. The aqueous layer, containing the analyte, was acidified to pH 2.2 and partitioned with fresh dichloromethane. The dichloromethane layer containing the analyte was evaporated, and the residue was dissolved in the LC mobile phase for analysis. A polar embedded C18 column was used with a mobile phase of pH 2.2 aqueous phosphate buffer-acetonitrile (68 + 32), run isocratically with detection at 225 nm. The average recovery was 82% with a relative standard deviation (RSD) of 10%. A coefficient of determination of R2 = 0.9992 was achieved for the analyte calibration curve, from 0.005 to 1 microg/mL. The limit of detection, determined from 3 times the standard deviation of 7 replicate extractions of the lowest fortification level (0.01 microg/g), was 0.005 microg/g with an RSD of 22%. LC/electrospray ionization/mass spectrometry in the positive-ion mode was used for identity confirmation of flumetsulam in the fortified soybean extract. The ions at m/z 326, 348, and 129 were observed.     

Liquid chromatographic determination of nicarbazin in feeds

A new liquid chromatographic method has been developed for determination of nicarbazin in feeds. Approximately 40 g feed is extracted with 200 mL acetonitrile-water (80 + 20, v/v). An aliquot of the extract is filtered and assayed using a reversed-phase isocratic method that measures the 4,4'-dinitrocarbanilide moiety of nicarbazin at a wavelength of 340 nm. For medicated feeds, the method uses a standard linear range of 5 to 100 microg/mL. For lower levels, a linear range of 50 to 150 ng/mL can be used. The method has a limit of detection of 250 ng/g and a limit of quantitation of 500 ng/g in a 40 g feed sample. Recovery was 99.1%, with a range of 95.2 to 101.8%. In the typical U.S. dosing range of 27 to 113.5 g/ton, the precision of the method based on one analyst, one day, and 2 weighings ranged from 2.8% (113.5 g/ton) to 4.7% (27 g/ton).     

Liquid chromatographic determination of triasulfuron in soil

Two extraction methods were developed for the determination of triasulfuron in soil. Method I included extraction with methanol-phosphate buffer at pH 7 (2 + 1, v/v), liquid-liquid partition with dichloromethane, and cleanup on a liquid chromatographic Si adsorption solid-phase extraction tube. In Method II, Extrelut was added and the sample was then extracted with acetonitrile. In both cases, the extracts were analyzed by liquid chromatography (LC) with UV detection and the LC peak was confirmed by LC/mass spectrometry (MS). The 2 methods were tested on 3 soils having different physicochemical characteristics. Method I gave 83% average recovery and a determination limit of 0.4 microg/kg soil. Method II gave 67% average recovery and a determination limit of 2 microg/kg soil. Examples of application of Method I to field samples are reported.     

Liquid chromatographic determination of trimethylamine in water

A method for the selective determination of trimethylamine (TMA) in aqueous matrices by liquid chromatography is reported. The proposed procedure is based on the derivatization of the analyte with 9-fluorenylmethyl chloroformate (FMOC) in a precolumn (Hypersil C18, 30 microm, 20 mm x 2.1 mm i.d.) connected on-line to the analytical column (LiChrosphere 100 RP18, 5 microm, 125 mm x 4 mm i.d.). Gradient elution was performed with a mixture of acetonitrile-water-0.05 M borate buffer (pH 9.0). The method has been applied to the direct determination of TMA in water within the 0.25-10.0 microg/ml concentration interval, and can also be adapted to the determination of TMA over the range 0.05-1.0 microg/ml by incorporating a preconcentration stage with C18 solid-phase extraction (SPE) cartridges. Good linearity, reproducibility and accuracy was achieved within the tested concentration intervals. The limits of detection at 262 nm were 50 and 5 ng/ml for the direct method and for the method involving preconcentration, respectively. The proposed conditions allowed the selective determination of TMA in the presence of other primary and secondary short-chain aliphatic amines. The utility of the described procedure has been tested by determining TMA in different water samples.     

Validated kinetic spectrophotometric method for the determination of metoprolol tartrate in pharmaceutical formulations

A kinetic spectrophotometric method has been described for the determination of metoprolol tartrate in pharmaceutical formulations. The method is based on reaction of the drug with alkaline potassium permanganate at 25+/-1 degrees C. The reaction is followed spectrophotometrically by measuring the change in absorbance at 610 nm as a function of time. The initial rate and fixed time (at 15.0 min) methods are utilized for constructing the calibration graphs to determine the concentration of the drug. Both the calibration graphs are linear in the concentration range of 1.46 x 10(-6)-8.76 x 10(-6) M (10.0-60.0 microg per 10 ml). The calibration data resulted in the linear regression equations of log (rate)=3.634+0.999 log C and A=6.300 x 10(-4)+6.491 x 10(-2) C for initial-rate and fixed time methods, respectively. The limits of quantitation for initial rate and fixed time methods are 0.04 and 0.10 microg ml(-1), respectively. The activation parameters such as E(a), DeltaH(double dagger), DeltaS(double dagger) and DeltaG(double dagger) are also evaluated for the reaction and found to be 90.73 kJ mol(-1), 88.20 kJ mol(-1), 84.54 J K(-1) mol(-1) and 63.01 kJ mol(-1), respectively. The results are validated statistically and through recovery studies. The method has been successfully applied to the determination of metoprolol tartrate in pharmaceutical formulations. Statistical comparison of the results with the reference method shows excellent agreement and indicates no significant difference in accuracy and precision.     

Liquid chromatographic analysis of certain commercial formulations for non-opioid analgesics

A simple and sensitive method for separation and quantitative determination of non-opioid analgesics from pharmaceutical preparations has been developed and validated. Commercial formulations of three non-opioid analgesics, viz. paracetamol, ibuprofen and diclofenac, were chosen for present studies. These were extracted, isolated, purified and recrystallized and were characterized by melting point, lambda(max) and IR. Quantitative determination was carried out using HPLC and TLC supplemented with UV spectrophotometry.     

Liquid chromatographic determination of erythromycins in fermentation broth

Summary A simple and sensitive isocratic LC method is described for the determination of erythromycins in fermentation broths. A simple technique utilizing acetone-methyl ethyl ketone, 1∶1, as extraction solvent was coupled with suitable chromatographic conditions—compounds were separated on a 250 mm×4.6 mm i.d., 5 μm, reversed-phase column at 65°C with acetonitrile-0.2m K₂HPO₄ pH7.0-water, 35:5:60 (v/v), as mobile phase at a flow rate of 1.0 mL min⁻¹. UV detection was performed at 215 nm. Separation of erythromycin F from polar components of the fermentation liquid was sufficient. Erythromycins A, B, C, D, and E, andN-desmethylerythromycin A were also separated, as were known decomposition products of erythromycin A and several unknown components. The method is suitable for monitoring the progress of erythromycin fermentation.     

Liquid chromatographic determination of Alternaria toxins in carrots

A liquid chromatographic (LC) method was developed for the determination of Alternaria radicina and A. alternata toxins in carrots. Toxins were extracted from carrot with an acidified mixture of water-methanol-acetonitrile. The filtered extract was divided in 2 parts that were purified by solid-phase extraction on a C18 column for the analysis of radicinin (RAD), altertoxin-I (ATX-I), alternariol (AOH), and alternariol methyl ether (AME), and on a polymeric Oasis HLB column for tenuazonic acid (TeA). Toxins were quantified by reversed-phase LC with UV diode array detection by using 2 consecutive isocratic mixtures of acetonitrile-sodium dihydrogen phosphate solution. Mean recoveries of TeA, ATX-I, AME, RAD, and AOH from carrots spiked at levels between 0.5 and 3.0 microg/g were 69, 71, 90, 36, and 78%, with mean within-laboratory repeatability of 14, 5, 4, 6, and 18%, respectively. The mean between-laboratory reproducibilities for the determination of TeA, ATX-I, AME, and RAD in spiked samples were 25, 22, 6, and 12%, respectively. Limits of detection (signal-to-noise ratio of 3) for RAD, TeA, ATX-I, AME, and AOH were 0.006, 0.02, 0.02, 0.01, and 0.005 microg/g, respectively. RAD was detected (0.16-13.9 microg/g) in 3 out of 266 carrot samples produced under organic conditions in 3 European locations, whereas A. alternata mycotoxins were not found in any tested samples.     

Liquid chromatographic determination of nystatin in pharmaceutical preparations

A rapid, reversed-phase liquid chromatographic method was developed for the assay of nystatin in the bulk drug and a variety of dosage forms. Analysis was performed on a Symmetry C18 reversed-phase column using a mobile phase of methanol-water-dimethylformamide (DMF; 55 + 30 + 15, v/v/v), with detection by UV at 305 nm. Quantitation is based on the sum of the peak areas of the 2 major isomers of nystatin. The linearity of the assay was determined for a concentration range of 0.05 to 0.2 mg/mL (correlation coefficient > 0.999). Accuracies and precision showed good reproducibility.     

Liquid chromatographic methods for chloral hydrate determination

Liquid chromatographic methods, based on reversed-phase (RP) and anion-exchange mechanisms, have been developed for chloral hydrate determination. Both methods are preceeded by derivatization of chloral hydrate. For RP separations, different reagents [namely dansylhydrazine and o-(4-nitrobenzyl)hydroxylamine] have been studied, but the best results have been achieved using 1,2-benzenedithiol with UV detection at 220 nm. The anion-exchange method is based on derivatization with NaOH to form sodium formate that is then analyzed by anion-exchange, with suppressed conductivity detection. Derivatization conditions were optimized in order to reach the best yield of reaction. The optimization of the procedure allowed to determine chloral hydrate with detection limits as low as 0.2 μg/l with good linearity and reproducibility. The anion-exchange method was also applied for chloral hydrate determination in a drinking water sample. A preconcentration procedure has also been studied.     

Liquid chromatographic determination of nine N-methylcarbamates in drinking water

A multi-residue method for the simultaneous extraction from drinking water using solid-phase extraction on LiChrolut EN [poly(styrene-divinylbenzene), PSDVB] and determination of nine N-methylcarbamate pesticides (NMCs) (aldicarb, its metabolites i.e. aldicarb sulfone and aldicarb sulfoxide and carbaryl, carbofuran, dioxacarb, ethiofencarb, methomyl and propoxur) using reversed-phase liquid chromatography was studied. A 1000-fold pre-concentration was achieved and the method was used for determination of the nine pesticides in water, with limits of detection in the range 3-15 ng L(-1). For all compounds the recoveries determined at the 0.1 and 1 microg L(-1) level generally ranged from 85 to 104% with relative standard deviations (RSD) of 1.4-8.8%.