Isolation and purification of lignans from Magnolia biondii Pamp by isocratic reversed-phase two-dimensional liquid chromatography following microwave-assisted extraction

The dried flower buds of Magnolia biondii Pamp are one of the most widely used medicinal plants officially listed in the Chinese Pharmacopoeia. A 2-D column-switching system without sample loop trapping, where two columns were switched directly via a six-port two-position switching valve, was successfully applied for the first time to the isolation and purification of five lignans including pinoresinol dimethyl ether, magnolin, epi-magnolin A, fargesin, and demethoxyaschantin from M. biondii Pamp after microwave-assisted extraction. The introduction of the six-port switching valve instead of sample loop assured 100% recovery from the first dimension to the second, and the injection volumes of the second dimension could reach 12 mL. In this mode of operation, the solvent consumption of the 2-D approach was less than 30% that of conventional gradient methods with even larger sample size. The simultaneous operations of the two dimensions allowed the cycle time to be less than 16 min, compared to 90 min in the gradient elution single-dimension mode of operation. All of the five lignans were isolated at high purities of over 99% with approximately 95% recoveries.     

Theoretical advantages and drawbacks of on-line,multidimensional liquid chromatography using multiple columns operated in parallel

The theoretical advantages and drawbacks of using a multiple-, parallel column approach in on-line multidimensional liquid chromatography systems were investigated. Much time or peak capacity can be gained with the use of multiple parallel columns at the second-dimension while the aggregate time of separation increases only by the increment of the gradient time of the second-dimension. Multidimensional chromatographic systems are now used to perform many tasks ranging from routine, fast analyses to specialized, arduous separations. In this work, we focus on the advantages of a multiple, parallel columns approach to on-line multidimensional liquid chromatography systems. Calculations of the achievable peak capacities were made as functions of the number of columns operated in parallel. Increasing the number of second-dimension columns from one to two or three causes the largest increase in peak capacity with only a slight increase of aggregate time. We also present some practical aspects to consider when attempting multidimensional separations with multiple columns operated in parallel.     

Isolation and purification of isoflavonoids from Rhizoma Belamcandae by two‐dimensional preparative high‐performance liquid chromatography with column switch technology

A two‐dimensional column‐switching system without sample loop trapping, where two columns were operated via a six‐port switching valve, was employed in the isolation and purification of five isoflavonoids from Rhizoma Belamcandae: tectoridin, iridin, tectorigenin, irigenin and irisflorentin. The introduction of the six‐port switching value, instead of a sample loop, assured 100% recovery from the first dimension to the second, and the injection volumes of the second dimension were not restricted. Two configurations were tested in this study. In the first mode, only one column was used in the second dimension and two ‘heart‐cutting’ fractions were transported to the same second‐dimensional column. In the second mode, two parallel columns were used in the second dimension and two fractions were transported to the two columns. Between the two configurations, the one with two second dimensional columns had double sample size, better resolution and one more purified compound. Both two‐dimensional configurations consumed less solvent with even greater efficiency and shorter cycle time compared with conventional gradient methods. All of the isoflavonoids were isolated at high purities of greater than 95% with yields of above 82%. Copyright © 2009 John Wiley & Sons, Ltd.     

Probing the kinetic performance limits for ion chromatography. II. Gradient conditions for small ions

A gradient kinetic plot method is used for theoretical characterisation of the performance of polymeric particulate anion exchange columns for gradient separations of small inorganic anions. The method employed requires only information obtained from a series of isocratic column performance measurements and in silico predictions of retention time and peak width under gradient conditions. Results obtained under practically constrained conditions provide parameters for the generation of high peak capacities and rapid peak production for fast analysis to be determined. Using this prediction method, a maximum theoretical peak capacity of 84 could be used to achieve separation of 26 components using a 120 min gradient (R_s > 1). This approach provides a highly convenient tool for development of both mono- and multidimensional ion chromatography (IC) methodologies as it yields comprehensive understanding of the influence of gradient slope, analysis time, column length and temperature upon kinetically optimised gradient performance.     

Comparison between adsorption isotherm determination techniques and overloaded band profiles on four batches of monolithic columns

The adsorption isotherms of 4-tert.-butyl phenol were measured on four different monolithic columns, using three different techniques, classical frontal analysis (FA), the perturbation on a plateau method (PP) and the recently introduced numerical procedure known as the inverse numerical method (IN). This last approach requires only the recording of a few overloaded profiles and has the potential advantage of affording a dramatic decrease of the amounts of compounds, solvent, and time needed to determine accurate estimates of the coefficients of the isotherm. The reproducibility of the adsorption data measured on the four columns is discussed with reference to the specific techniques used for obtaining these data and to the most suitable equation used for modeling them. The data obtained for the different columns were highly consistent. The inverse numerical approach was confirmed to provide a powerful, accurate, and economic method for measuring single component adsorption data.     

Application of displacement chromatography for the proteome analysis of a human plasma protein fraction

It was the aim of this study to compare the performance of displacement chromatography with gradient elution chromatography both applied as the cation-exchange separation step for a proteome analysis in a bottom-up approach using multidimensional chromatography for the separation of tryptic peptides prior to their mass spectrometric analysis. The tryptic digest of the human Cohn fraction IV-4 served as a sample. For both chromatography modes commonly used operating parameters were chosen thus ensuring optimal separation results of equal sample amounts for each mode. All resulting fractions were analyzed with an HPLC-chip–LC–MS system. The eluate of the HPLC-chip column was ionized by electrospray ionization (ESI) and analyzed with an ion-trap mass spectrometer. For guaranteeing high confidence concerning the identity of the peptides, the mass spectrometric data were processed by different bioinformatic tools applying stringent criteria. By the displacement approach the total amount of identified proteins (78) was significantly higher than in the gradient mode (58). The results showed that displacement chromatography is a well suited alternative in comparison to gradient elution separation for analysis of proteomes via the bottom-up approach applying multidimensional chromatography, especially in those cases when larger quantities of proteins are available.     

氨基己酸为配基的新型弱阳离子交换/疏水双功能色谱固定相对蛋白质的分离纯化

以硅胶为基质、氨基己酸为配基制备了一种新型弱阳离子交换/疏水（WCX/HIC）双功能混合模式色谱固定相。该固定相配基具有一定的疏水性且含有羧基,在高盐浓度下表现为HIC的性质,可作为HIC固定相使用;在低盐浓度条件下表现为离子交换的性质,可作为WCX固定相使用。分别考察了该介质在WCX和HIC两种模式下对标准蛋白质的分离性能,并与商品柱进行比较。结果表明,所合成的WCX/HIC双功能固定相在WCX和HIC两种模式下对蛋白质均有较高的分离度和选择性,且分离能力与商品柱相当,两种模式下标准蛋白质的质量和活性回收率均大于93%,表明该柱具有“一柱二用”的功能,适于生物大分子的分离纯化。基于此双功能色谱柱构建的在线单柱二维液相色谱（2DLC-1C）可在60 min内实现8种蛋白质的快速分离。在70 min内完成了对蛋清中溶菌酶的二维纯化,纯度可达到98.3%。该技术中一根色谱柱可当作两根色谱柱使用,对蛋白质组学研究和重组蛋白药物的生产具有重要的应用价值。     

Two-dimensional ion chromatography using tandem ion-exchange columns with gradient-pulse column switching

A two-dimensional ion chromatography (2D-IC) approach has been developed which provides greater resolution of complex samples than is possible currently using a single column. Two columns containing different stationary phases are connected via a tee-piece, which enables an additional eluent flow and independent control of eluent concentration on each column. The resultant mixed eluent flow at the tee-piece can be varied to produce a different eluent concentration on the second column. This allows analytes strongly retained on the first column to be separated rapidly on the second column, whilst maintaining a highly efficient, well resolved separation of analytes retained weakly on the first column. A group of 18 inorganic anions has been separated to demonstrate the utility of this approach and the proposed 2D-IC method provided separation of this mixture with resolution of all analytes greater than 1.3. Careful optimisation of the eluent profiles on both columns resulted in run times of less than 28 min, including re-equilibration. Separations were performed using isocratic or gradient elution on the first column, with an isocratic separation being used on the second column. Switching of the analytes onto the second column was performed using a gradient pulse of concentrated eluent to quickly elute strongly retained analytes from the first column onto the second column. The separations were highly repeatable (RSD of 0.01–0.12% for retention times and 0.08–2.9% for peak areas) and efficient (typically 8000–260,000 plates). Detection limits were 3–80 ppb.     

High Performance Liquid Chromatographic Analysis of Pharmaceuticals Using Oil-In-Water Microemulsion Eluent and Monolithic Column

Novel and efficient separations of pharmaceutical substances were achieved using oil-in-water microemulsion eluent and a conventional C18 packing with a flow rate of 1 mL/min⁻¹. Attempts to decrease analysis time was limited due to the high viscosity of the microemulsion which generated relatively high back-pressures. Monolithic columns gave 3-fold lower back-pressures and allowed flow rates of 4 mL/min⁻¹. with the same microemulsion mobile phase which permitted rapid separations to be achieved. Separation of a test-mix of paraben preservatives was achieved in both isocratic and gradient mode in less than 1 min. The monolith-microemulsion combination was applied to rapidly quantitatively analyse two formulated products with excellent linearity, accuracy and repeatability. Quantitative analysis times were under 90 seconds. Successful quantitation of both nicotine lozenges and naprosyn tablets was performed using this approach.     

Evaluation of multidimensional (ion-exchange/reversed-phase) protein separations using linear and step gradients in the first dimension

The performance characteristics of multidimensional liquid chromatographic protein separations were evaluated using on-line electrospray mass detection, and a novel workflow for automated LC/MS data processing. Two-dimensional ion exchange/reversed-phase LC separations of Escherichia coli cytosol were conducted using either a continuous linear or discontinuous step gradient in the first dimension. Chromatographic profiles of the top 100 most abundant components were characterized to assess overall separation reproducibility within each mode, and to characterize differences in component distribution between the two modes of operation. Analysis of the resulting data indicates that multidimensional separations of complex protein mixtures can be done reproducibly. Furthermore, under the conditions employed within this study, a linear first dimension gradient was more effective at fractionating the protein mixture, distributing fewer major components to multiple second dimension cycles than an equivalent step gradient. The application of on line mass spectrometry, and automated processing of the resulting data, proved valuable for producing component level analysis of multidimensional protein separations.     

Simultaneous analysis of amino acid and biogenic polyamines by high-performance liquid chromatography after pre-column derivatization with N-(9-fluorenylmethoxycarbonyloxy)succinimide

A high-performance liquid chromatography method for the simultaneous analysis of amino acids and biogenic polyamines, using a new procedure for pre-column derivatization of amino groups with N-(9-fluorenylmethoxycarbonyloxy)succinimide is described. The separation of 20 amino acids and 4 biogenic polyamines was achieved within 32 min on a sequence of three short (50 mm) reversed-phase C18, 5 microm columns by elution buffers based on dibutylamine phosphate. The method linearity, calculated for each amino acid and polyamine, has a correlation coefficient higher than 0.991, in concentrations ranging from 0.2 to 50 microM, except for spermine and methionine, where the correlation coefficients were r = 0.984 and r = 0.979, respectively. The stability of derivatives in acidified samples at 4 degrees C and room temperature was demonstrated. The limit of quantitation was estimated to be around 50 pM in 50 microl sample injection. The repeatability of the method, expressed as R.S.D., ranged from 1.1 to 6.7%. The presented method was applied for the quantitation of amino acid and polyamine contents in beer, wine, and cell culture samples, using 2-aminoheptanoic acid or 1,7-diaminoheptane as internal standard.     

Selective displacement chromatography in multimodal cation exchange systems

A library of displacer analogues with varying degrees of electrostatic, hydrophobic and hydrogen bonding moieties was evaluated for their ability to enhance the selectivity of multimodal (MM) chromatography under high loading conditions. The library was screened for displacement of model proteins using a robotic liquid handling system and selective batch separations were achieved for proteins that were inseparable with linear gradient chromatography. Trends in protein displacement were identified and displacers with higher hydrophobicity and net charge exhibited improved protein displacements. Proteins that interacted with the resins primarily via electrostatic interactions were more readily displaced than those that possessed a significant hydrophobic contribution to their binding. In addition, multimodal displacers were found to be more selective than single mode electrostatic displacers. Column chromatography studies were also carried out and baseline separations were achieved for model protein pairs using selective displacement. Finally, operation of these columns in the desorption mode resulted in baseline separation of model proteins which were not separable by selective displacement chromatography. This study indicates that the inherent selectivity of MM resins can be augmented by the selectivity of the displacer under non-linear competitive binding conditions, creating new opportunities for protein separations not possible using traditional gradient operations.     

Tandem LC columns for the simultaneous retention of polar and nonpolar molecules in comprehensive metabolomics analysis

The tandem use of hydrophilic interaction LC columns with RP columns in series configuration has resulted in the retention of both polar and nonpolar components in complex biological samples (mouse serum) in a single analysis. This approach successfully coupled various columns with orthogonal separation characteristics, employed a single solvent gradient program compatible with the two columns and used ESI coupled to a TOF mass spectrometer for detection. Ion suppression, a common problem in ESI, was virtually eliminated for components eluting with apparent capacity factors >0.7. Retention time reproducibility with the tandem columns performed over three days with over 100 injections was comparable to that observed for single columns alone. This method was applied to the analysis of a pooled mouse serum sample and afforded highly reproducible data for up to 3000 mass spectral features. This approach was implemented with a conventional LC–MS system and should find broad applicability in the comprehensive analysis of complex mixtures containing a wide range of compound polarities.     

Separation of pectin methylesterase isoenzymes from tomato fruits using short monolithic columns

One of the main forms of tomato pectin methylesterase (PME; EC 3.1.1.1.1) that is applicable to the food industry was isolated from fresh tomato fruit. The extraction of the PME isoenzymes involved washing the fresh tomato flesh with water in order to remove sugars and than solubilizing the enzymes with a diluted HCl solution at pH 1.6. The extract was then neutralized to pH 7.4 using buffer solution. After filtration, the solution was directly fractioned using Convective Interaction Media (CIM) short monolithic disk column bearing sulfonyl (SO3) groups and using a linear gradient from 0 to 700 mM NaCl. The injection volume was 3 ml and the diameter of the column was 12 mm and length 3 mm. The isolated fractions were monitored for protein content and PME activity. The fraction with the targeted enzyme, which showed NaCl independent activity, was further purified and concentrated by ultrafiltration and finally purified by a second semi-preparative cation-exchange chromatography step using a CIM carboxymethyl (CM) disk monolithic column consisting of two disks and applying a step gradient. From 1 kg of fresh tomato fruits, 7.5 mg of purified PME with molecular mass estimated to be 26 000 by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) was obtained. A fraction with mixed PME and polygalacturonase activity was also obtained. Compared to the published procedures for the isolation and purification of PME from plant materials, this new procedure is much faster and more efficient. The potential application of CIM disk short monolithic columns in the analysis and semi-preparative extraction and isolation of the PME isoenzyme is presented.     

Peak capacity in gradient reversed-phase liquid chromatography of biopolymers. Theoretical and practical implications for the separation of oligonucleotides

Reversed-phase ultra-performance liquid chromatography was used for biopolymer separations in isocratic and gradient mode. The gradient elution mode was employed to estimate the optimal mobile phase flow rate to obtain the best column efficiency and the peak capacity for three classes of analytes: peptides, oligonucleotides and proteins. The results indicate that the flow rate of the Van Deemter optimum for 2.1 mm I.D. columns packed with a porous 1.7 microm C18 sorbent is below 0.2 mL/min for our analytes. However, the maximum peak capacity is achieved at flow rates between 0.15 and 1.0 mL/min, depending on the molecular weight of the analyte. The isocratic separation mode was utilized to measure the dependence of the retention factor on the mobile phase composition. Constants derived from isocratic experiments were utilized in a mathematical model based on gradient theory. Column peak capacity was predicted as a function of flow rate, gradient slope and column length. Predicted peak capacity trends were compared to experimental results.     

Application of multidimensional switching to the analysis of volatiles

A multidimensional switching system with two packed columns has been used for the analysis of volatiles. Use of a high-boiling solvent and the backflush mode permitted total resolution of the mixture discussed in a short analysis time.     

High-performance liquid chromatography of seized drugs at elevated pressure with 1.7 microm hybrid C18 stationary phase columns

High-performance liquid chromatography (HPLC) separation of drugs at elevated pressure with 1.7 microm hybrid C18 stationary phase columns was investigated. This technique, which uses instrumentation engineered to handle the narrow peaks and high back pressures generated by 1.7 microm particle columns, provided significantly better resolution and/or faster analysis than conventional HPLC and capillary electrophoresis (CE). The use of 2mm internal diameter (i.d.) columns of 3-10 cm length has been evaluated for the separation of basic and neutral drugs, drug profiling, and general screening (including acidic drugs). For these applications, compared to conventional HPLC and CE, it provided up to 12x and 3x faster analyses, respectively. Precision was excellent for both isocratic and gradient analyses. For retention time and peak area, RSDs of < or =0.1% were obtainable. Fifteen anabolic steroids and esters were well separated in a 2.5 min gradient. For drug profiling, compared to HPLC and CE, approximately twice as many peaks were resolved. HPLC at elevated pressure is also well suited as a general screening technique. Twenty-four solutes of varying drug classes including narcotic analgesics, stimulants, depressants, hallucinogens, and anabolic steroids were fully separated in a 13.5 min gradient.     

Automated signature peptide approach for proteomics

This paper addresses the issue of automating the multidimensional chromatographic, signature peptide approach to proteomics. Peptides were automatically reduced and alkylated in the autosampler of the instrument. Trypsin digestion of all proteins in the sample was then executed on an immobilized enzyme column and the digest directly transferred to an affinity chromatography column. Although a wide variety of affinity columns may be used, the specific column used in this case was a Ga(III) loaded immobilized metal affinity chromatography (IMAC) column. Ga(III)-IMAC is known to select phosphorylated peptides. Phosphorylated peptides selected by the affinity column from tryptic digests of milk were automatically transferred to a reversed-phase liquid chromatography (RPLC) column. Further fractionation of tryptic peptides on the RPLC column was achieved with linear solvent gradient elution. Effluent from the RPLC column was electrosprayed into a time-of-flight mass spectrometer. The entire process was controlled by software in the liquid chromatograph. With slight modification, it is possible to add multiple columns in parallel at any of the single column positions to further increase throughput. Total analysis time in the tandem column mode of operation was under 2 h.     

Preparation of a weak anion exchange/hydrophobic interaction dual‐function mixed‐mode chromatography stationary phase for protein separation using click chemistry

In this study, 3‐diethylamino‐1‐propyne was covalently bonded to the azide‐silica by a click reaction to obtain a novel dual‐function mixed‐mode chromatography stationary phase for protein separation with a ligand containing tertiary amine and two ethyl groups capable of electrostatic and hydrophobic interaction functionalities, which can display hydrophobic interaction chromatography character in a high‐salt‐concentration mobile phase and weak anion exchange character in a low‐salt‐concentration mobile phase employed for protein separation. As a result, it can be employed to separate proteins with weak anion exchange and hydrophobic interaction modes, respectively. The resolution and selectivity of the stationary phase were evaluated in both hydrophobic interaction and ion exchange modes with standard proteins, respectively, which can be comparable to that of conventional weak anion exchange and hydrophobic interaction chromatography columns. Therefore, the synthesized weak anion exchange/hydrophobic interaction dual‐function mixed‐mode chromatography column can be used to replace two corresponding conventional weak anion exchange and hydrophobic interaction chromatography columns to separate proteins. Based on this mixed‐mode chromatography stationary phase, a new off‐line two‐dimensional liquid chromatography technology using only a single dual‐function mixed‐mode chromatography column was developed. Nine kinds of tested proteins can be separated completely using the developed method within 2.0 h.     

Potential of long capillary monolithic columns for the analysis of protein digests

The gain in separation efficiency for protein digests using long monolithic columns has been evaluated for a LC‐MS system with capillary monolithic columns of different lengths (150 and 750 mm). A mixture of BSA, α‐casein and β‐casein tryptic digests was used as a test sample. Peak capacity and productivity (peak capacity per unit time) were determined from base peak chromatograms and MS/MS data were used for protein identification by MASCOT database searching. Peak capacity and protein identification scores were higher for the long column. Analyses with similar gradient slope for the two columns produced ratios of the peak capacities that were slightly higher than the expected value of the square root of the column length ratio. Peak capacity ratios varied from 2.7 to 4.0 for four different gradient slopes, while protein identification scores were 2–4 times higher for the long column. Similar values were obtained for the productivity of both columns and the highest productivity was obtained at gradient times of 45 and 75 min for the short and long column, respectively. The use of long monolithic columns improves peptide separation and increases reliability of protein identification for complex digests, especially if longer gradients are chosen.