Ion-exchange chromatography separation of the detergent and the solvent from immunoglobulins after solvent-detergent treatment.

For inactivation of lipid-enveloped viruses during the immunoglobulin production, the solvent-detergent (S/D) method was applied. Tri-n-butyl phosphate (solvent) and Triton X-100 (detergent) were removed from S/D treated immunoglobulins by ion-exchange chromatography on Q-Sepharose Fast Flow (FF). During the chromatographic procedure immunoglobulins remained bound on a Q-Sepharose FF, whereas solvent and detergent were eluted by washing with starting buffer. Elution of immunoglobulins was achieved by increasing the ionic strength of the starting buffer. The final immunoglobulin preparation contained less than 10 microg/ml of Triton X-100 and less than 2 microg/ml tri-n-butyl phosphate. It was confirmed that the S/D procedure did not cause a significant change in polymers and specific antibodies content. Immunoglobulin classes were also not affected by the same procedure.     

Protein separation with surfactant-coated polystyrene involving Cibacron Blue 3GA-conjugated triton X-100

Through mixing of porous polystyrene particles (Amberlite XAD-4), non-ionic surfactants, and surfactant-conjugated substrates (affinity ligand) in an aqueous solution led to the formation of a novel medium (affinity admicelle) for protein separation. The ligand (CB-Triton) was synthesized by mixing a triazine dye (Cibacron Blue 3GA (CB)) and a polyoxyethylene-type non-ionic surfactant (Triton X-100) in weakly alkaline solutions. Triton X-100 and CB-Triton were competitively sorbed onto XAD-4. Albumin (bovine serum), alcohol dehydrogenase (yeast), and lysozyme (chicken egg) having specific interaction to CB were collected onto the affinity admicelle. On the other hand, the collection of ovalubmin (chicken egg white), having no binding ability to CB, was negligibly small. Lysozyme in 100 microl of chicken egg white, diluted with 900 microl of 10 mM Tris-HCl (pH 7.4), was successfully collected on 18 mg of CB-Triton admicelles and, then, it was eluted with 1 ml of aqueous solution of 100 mM phosphate (pH 7.4). The recovery based on the activity for the lysis of micrococcus and the concentration factor were 60% and 40 (n = 3), respectively.     

Determination of 1,4-dioxane impurity levels in Triton X-100 raw material by gas chromatography with mass spectrometric detection

Triton X-100 (octoxynol 9) is a commercially available surfactant used as a solvent detergent in numerous pharmaceutical applications including virus inactivation. A byproduct formed during its synthesis is 1,4-dioxane, the cyclic dimer of ethylene oxide and a possible carcinogen to humans. The United States Pharmacopoeia (USP) contains a labor-intensive 1,4-dioxane test for Triton X-100. The method couples vacuum distillation to extract the 1,4-dioxane from the Triton X-100 matrix followed by gas chromatography (GC) using a packed column with flame-ionization detection. In order to provide a more automated and specific test methodology, a headspace GC-mass spectrometry (MS) method has been developed for this application. Analyte quantitation is accomplished by the method of standard additions. The automated sample preparation, coupled with the specificity inherent in high-efficiency capillary column separations together with single-ion MS detection, results in an assay that is more efficient, accurate, and precise than the USP procedure. Performance characteristics of the headspace GC-MS method are contrasted with those characteristics of the USP methodology.     

Spectrophotometric determination of manganese with 1-(2-pyridylazo)-2-naphthol and a non-ionic surfactant

A spectrophotometric method for the determination of trace amounts of manganese with 1-(2-pyridylazo)-2-naphthol (PAN) is described. The method is based on the measurement of absorbance of the manganese—PAN chelate solubilized with a non-ionic surfactant, Triton X-100. No extraction procedure is required in the method proposed. High concentrations of calcium, aluminium and magnesium do not interfere. The presence of up to 10 ppm of lead can be tolerated. Iron, cadmium, zinc, cobalt and nickel can be effectively masked with potassium cyanide. Beer's law is obeyed up to 2 ppm of manganese. The molar absorptivity of the manganese—PAN chelate found was 4.4 × 10⁴ l. mole ⁻¹. cm⁻¹ at 562 nm. The overall stability constant of Mn(PAN)₂ in 0.4% Triton X-100 medium is 10^16.8.     

Application of tandem column solid phase extraction and flame atomic absorption spectrometry for the determination of inorganic and organically bound forms of iron in wine

A tandem column solid phase extraction (SPE) procedure has been devised to examine the fractionation of Fe in wine. Wine was filtered through a 0.45 μm filter and then, the filtrate was driven through an adsorbing Amberlite XAD-7HP column followed by a cation exchange Dowex 50W-x8-200 column. Three different Fe groupings are discriminated and assessed, including hydrophobic species of Fe bound to phenolic substances and related species (phenolic fraction), cationic species comprising simple Fe ions and labile Fe forms (cationic fraction), in addition to anionic and/or neutral Fe complexes with organic acids (residual fraction). The suitability of the procedure has been evaluated analyzing four bottled red wines. The results obtained were verified using another tandem column assemblage in which an adsorbing Amberlite XAD-16 column was exchanged by the Amberlite XAD-7HP column. The fractionation pattern ascertained for Fe in analyzed wines is discussed in reference to previously published works. In addition, a conditioning treatment and preparation of Amberlite XAD resins have been revised.     

Self-aggregation and supramolecular structure investigations of Triton X-100 and SDP2S by NOESY and diffusion ordered NMR spectroscopy

The self-aggregation and supramolecular micellar structure of two surfactants in aqueous solution, the anionic surfactant SDP2S (sodium dodecyl dioxyethylene-2 sulfate) and the nonionic surfactant Triton X-100 (octylphenol-polyoxyethylene ether with 9.5 ethoxy groups), were investigated by NMR spectroscopy. The critical micellar concentration (CMC), the size, and shape of the aggregates were determined by diffusion ordered NMR spectroscopy (DOSY), while 2D NOESY NMR spectra were used to study the mutual spatial arrangement of surfactant molecules in the aggregated state. A nonlinear increase of the micellar hydrodynamic radius, indicating possible sphere-to-rod shape transition, was found for SDP2S at higher surfactant concentrations. Triton X-100 micelles were found to be almost spherical at low surfactant concentrations, but formation of ellipsoid shaped particles and/or micellar aggregation was observed at higher concentrations. The NOESY data show that at low concentration Triton X-100 forms a two-layer spherical structure in the micelles, with partially overlapping internal and external layers of Triton X-100 molecules and no distinct hydrophilic-hydrophobic boundary.     

Anodic-stripping voltammetry of heavy metals in the presence of organic surfactants

The efficacy of fumed silica for removal of sorption interferences by organic surfactants in the anodic-stripping voltammetry of heavy metals is demonstrated. Appropriate addition of silica to the sample solution rapidly "purifies" it from interfering surfactants during the nitrogen purge step. Up to at least 6 ppm of gelatin, Triton X-100, albumin or Liqui-Nox then does not affect the stripping response of cadmium, lead and zinc at the hanging mercury drop electrode. A relative standard deviation of 5.5% is obtained for 20 successive measurements of 1 x 10(-7)M lead in the presence of 2 ppm Triton X-100. Analogous improvements are observed at the mercury film electrode (in the presence of up to 60 ppm of these surfactants). The use of silica thus possesses the advantages of speed, efficiency, simplicity and low cost compared to other schemes for dealing with surfactant interferences in anodic-stripping voltammetry.     

Effects of Triton X-100 on Properties of Hemoglobin and Controlled Release of Drug in Hemoglobin/Ribavirin/H2O System

Effects of Triton X-100 on the properties of hemoglobin (Hb) and on the controlled release of ribavirin were studied using the methods of UV-Vis spectrum, fluorescence spectrum, zeta potential, conductivity, high-performance liquid chromatographic (HPLC), and image morphology in Hb/ribavirin/H₂O system. With the increase of concentration of Triton X-100 in the system, the intrinsic fluorescence intensity, synchronous fluorescence intensity, fluorescence polarization, zeta potential, and morphology of Hb all changed gradually, and the ribavirin located on the Hb surface was dissociated and released out. When the concentration of Triton X-100 was higher than 1×10⁻⁵ mol·L⁻¹, the stronger interaction of Triton X-100 with Hb was predominant. Hb was unfolded and denaturized. A little Triton X-100 can protect Hb from the effects of ribavirin.     

On-line preconcentration system for bismuth determination in urine by flow injection hydride generation inductively coupled plasma atomic emission spectrometry

An on-line bismuth preconcentration and determination system implemented with hydride generation inductively coupled plasma atomic emission spectrometry (HG-ICP-AES) associated to flow injection (FI) was studied. Quinolin-8-ol and Amberlite XAD-7 were used for the retention of bismuth, at pH 4.5. The bismuth complex was removed from the micro-column with nitric acid. The detection limit value for the preconcentration of 100 ml of aqueous solution was 0.02 ng ml(-1) with a relative standard deviation (R.S.D.) of 3.5%, calculated from the peak heights obtained. The calibration graph using the preconcentration system for bismuth was linear with a correlation coefficient of 0.999 at levels near the detection limits up to at least 100 ng ml(-1). The method was successfully applied to the determination of bismuth in human urine samples.     

Preconcentration and determination of Ce, La and Pr by X-ray fluorescence analysis, using Amberlite XAD resins loaded with 8-Quinolinol and 2-(2-(5 chloropyridylazo)-5-dimethylamino)-phenol

8-Quinolinol (oxine) and 2-(2-(5 chloropyridylazo)-5-dimethylamino)-phenol (5ClDMPAP) were immobilized on the non ionic sorbents Amberlite XAD-4 and XAD-7. These loaded resins were used for the preconcentration of Ce, La and Pr. High preconcentration factors were obtained in each case. After the retention of these rare earths, the resins were measured as thin films by x-ray fluorescence spectrometry. Up to 50 ppm of REEs can be retained on these thin films.     

Sensitive high-performance anion-exchange chromatographic determination of paeoniflorin and albiflorin by pulsed amperometric detection after solid-phase extraction

We developed a method to simultaneously determine paeoniflorin and albiflorin levels using high-performance anion-exchange liquid chromatography with pulsed amperometric detection (HPAEC-PAD). The main principle of our method includes solid-phase extraction step using Amberlite XAD-2 sorbent to remove sugars and to selectively determine glycosides by PAD. Under these conditions, the linear dynamic range was 0.01–100 μg/mL, and the albiflorin and paeoniflorin detection limits (S/N = 3) were 5 and 10 pg, respectively. The intra- and inter-day precisions (RSDs) were <5.07%, and the average recoveries from Paeoniae Radix and Si-ni-san ranged from 97.12 to 101.15%. Our method showed high selectivity, high sensitivity, and good repeatability for analyzing albiflorin and paeoniflorin in oriental medicinal preparation.     

非离子表面活性剂对流动注射电化学发光的增敏作用

研究了非离子表面活性剂聚乙二醇辛基苯基醚(Triton X-100)对流动注射电化学发光的影响。结果发现,Triton X-100对检测低浓度三联吡啶钌(Ru(bpy)23+)有增强作用,而且Triton X-100的引入可以改变流动注射电化学发光分析系统中Ru(bpy)23+-三正丙胺(TPA)反应电极电位。在检测电位1.35V,进样量100μL,进样速度50μL/s条件下,对Ru(bpy)23+进行检测,检出限(S/N=3)达1.0×10-10 mol/L,较添加Triton X-100前灵敏度提高50倍。     

Cloud point extraction equilibrium of lanthanum(III), europium(III) and lutetium(III) using di(2-ethylhexyl)phosphoric acid and Triton X-100

The cloud point extraction behaviors of lanthanoids(III) (Ln(III) = La(III), Eu(III) and Lu(III)) with and without di(2-ethylhexyl)phosphoric acid (HDEHP) using Triton X-100 were investigated. It was suggested that the extraction of Ln(III) into the surfactant-rich phase without added chelating agent was caused by the impurities contained in Triton X-100. The extraction percentage more than 91% for all Ln(III) metals was obtained using 3.0 × 10⁻⁵ mol dm⁻³ HDEHP and 2.0% (v/v) Triton X-100. From the equilibrium analysis, it was clarified that Ln(III) was extracted as Ln(DEHP)₃ into the surfactant-rich phase. The extraction constant of Ln(III) with HDEHP and 2.0% (v/v) Triton X-100 were also obtained.     

非离子表面活性剂层状液晶的结构与增溶作用

相行为研究表明，与ＴｒｉｔｏｎＸ－１００／Ｃ＿６Ｈ＿６／Ｈ＿２Ｏ体系相比，ＴｒｉｔｏｎＸ－１００／Ｃ＿（１０）Ｈ＿（２１）ＯＨ／Ｈ＿２Ｏ体系更易于生成层状液晶，并更为稳定，小角Ｘ－射线衍射表明；ＴｒｉｔｏｎＸ－１００／Ｃ＿（１０）Ｈ＿（２１）ＯＨ／Ｈ＿２Ｏ体系层状液晶中，Ｃ＿（１０）Ｈ＿（２１）ＯＨ与ＴｒｉｔｏｎＸ－１００交替排列于两亲双层中，Ｃ＿（１０）Ｈ＿（２１）ＯＨ／ＴｒｉｔｏｎＸ－１００重量比增加，两亲双层厚度ｄ＿０值不变。以Ｃ＿６Ｈ＿６代替Ｃ＿（１０）Ｈ＿（２１）ＯＨ后，Ｃ＿６Ｈ＿６存在于两亲双层的油层和渗入ＴｒｉｔｏｎＸ－１００分子链尾周围，使得溶剂渗透率减少，并且Ｃ＿６Ｈ＿６／ＴｒｉｔｏｎＸ－１００增加，ｄ＿０值增加。     

Triton X-100存在下镉试剂分光光度法测定痕量铊(III)

本文首次提出了在Triton X-100存在下, 以镉试剂作显色剂于水相直接分光光度法测定了痕量铊, 结果表明: 该体系具有很高的灵敏度, 是目前分光光度法测定铊的最灵敏方法之一.     

Analysis of traces of surfactants in water with anion-exchange resin and polymeric adsorbent

Summary Determination of traces of anionic and non-ionic surfactants in water has been based on the quantitative separation of sodium alkylbenzene sulphonate (LAS) from polyoxyethylenealkylphenyl ether (APE) with a weak base anion-exchange resin, and adsorption of APE in filtrate with Amberlite XAD-2 resin. LAS is adsorbed on the anionexchange resin, eluted with hydrochloric acid-methanol and determined spectrophotometrically by methylene blue or UV absorption. APE in the filtrate is adsorbed on XAD-2 resin, eluted with methanol and determined spectrophotometrically by cobalt thiocyanate or UV absorption. Recoveries of surfactants were about 90100%. As little as 0.02 ppm can be determined. In a river water sample 0.06 ppm of LAS and 0.05 ppm of APE and in another case, 0.12 ppm of LAS and 0.07 ppm of APE were found.

---

Spurenanalyse von oberflächenaktiven Substanzen in Wasser mit Hilfe eines Anionenaustauschers und eines Polymeradsorbens

Zusammenfassung Natriumalkylbenzolsulfonat (LAS) kann von Polyoxyethylenalkylphenylether (APE) getrennt werden, indem LAS an einem schwachbasischen Anionenaustauscher und im Filtrat APE an Amberlit XAD-2 adsorbiert wird. LAS wird mit Methanol-HCl eluiert und im Eluat spektralphotometrisch mit Methylenblau oder durch UV-Absorption bestimmt. APE wird mit Methanol eluiert und spektralphotometrisch mit Cobaltthiocyanat oder ebenfalls durch UV Absorption bestimmt. Bei Zusatzversuchen wurden 90–100% wiedergefunden. Bis zu 0.02 ppm können bestimmt werden. In einer Flußwasserprobe wurden 0,06 ppm LAS und 0,05 ppm APE bzw. 0,12 ppm LAS und 0,07 ppm APE gefunden.

     

表面活性离子液体溴化N-十二烷基异喹啉与非离子表面活性剂Triton X-100在水溶液中的混合胶束

用等温滴定微量热法测定表面活性离子液体溴化N-十二烷基异喹啉([C₁₂iQuin]Br)与非离子表面活性剂Triton X-100混合物在水溶液中的临界胶束浓度。并以¹H核磁共振(NMR)和二维核Overhauser效应增强谱(2D NOESY)研究[C₁₂iQuin]Br与Triton X-100在混合胶束中的作用机理。研究结果显示：混合胶束中,Triton X-100分子的苯环定位于混合胶束的内核,聚氧乙烯链卷曲在异喹啉环周围。本文还应用规则溶液理论和浊点法对比研究了十二烷基三甲基溴化铵(DTAB)-Triton X-100混合胶束体系的相关性质。     

Inhibition of Triton X-100／n-C5H11OH／H2O System on Hydrolysis of Cephanone

The hydrolysis of cephanone in Triton X-100 micelle and Triton X-100/n-C5H11OH/H2O(O/W) microemulsion were studied by means of UV-Vis absorption spectroscopy. The results show that compared with water, Triton X-100 micelle and Triton X-100/n-C5H11OH/H2O (O/W) microemulsion can inhibit the hydrolysis of cephanone. The inhibition effects of Triton X-100 micelle and Triton X-100/n-C5H11OH/H2O (O/W) microemulsion on the hydrolysis of cephanone are related to the location of cephanone in the interphases of Triton X-100 miceUes and Triton X-100/n-C5H11OH/H2O(O/W) microemulsion droplets.     

Cloud point extraction of iron(III) and vanadium(V) using 8-quinolinol derivatives and Triton X-100 and determination of 10(-7)moldm(-3) level iron(III) in riverine water reference by a graphite furnace atomic absorption spectroscopy

The cloud point extraction behavior of iron(III) and vanadium(V) using 8-quinolinol derivatives (HA) such as 8-quinolinol (HQ), 2-methyl-8-quinolinol (HMQ), 5-butyloxymethyl-8-quinolinol (HO₄Q), 5-hexyloxymethyl-8-quinolinol (HO₆Q), and 2-methyl-5-octyloxymethyl-8-quinolinol (HMO₈Q) and Triton X-100 solution was investigated. Iron(III) was extracted with HA and 4% (v/v) Triton X-100 in the pH range of 1.70-5.44. Above pH 4.0, more than 95% of iron(III) was extracted with HQ, HMQ, and HMO₈Q. Vanadium(V) was also extracted with HA and 4% (v/v) Triton X-100 in the pH range of 2.07-5.00, and the extractability increased in the following order of HMQ < HQ < HO₄Q < HO₆Q. The cloud point extraction was applied to the determination of iron(III) in the riverine water reference by a graphite furnace atomic absorption spectroscopy. When 1.25 × 10⁻³ M HMQ and 1% (v/v) Triton X-100 were used, the found values showed a good agreement with the certified ones within the 2% of the R.S.D. Moreover, the effect of an alkyl group on the solubility of 5-alkyloxymethyl-8-quinolinol and 2-methyl-5-alkyloxymethyl-8-quinolinol in 4% (v/v) Triton X-100 at 25 °C was also investigated.     

Dynamic coating for resolving rhodamine B adsorption to poly(dimethylsiloxane)/glass hybrid chip with laser-induced fluorescence detection

In this paper a method was described about dynamic coating for resolving rhodamine B (RB) adsorption on a hybrid poly(dimethylsiloxane) (PDMS)/glass chip. The results showed that when the non-ionic surfactant Triton X-100 was higher than 0.5% (v/v) into the phosphate buffer, the adsorption of RB appeared. Besides, some separation conditions for RB were investigated, including concentration of Triton X-100, concentration and pH value of running buffer, separation voltage and detection site. Through comparing electroosmotic flow, plate numbers and other parameters, an acceptable separation condition was obtained. Under optimized conditions, the precisions of RB detection (R.S.D., n = 10) were 2.62% for migration time, 4.78% for peak height respectively. Additionally, RB concentration linearity response was excellent with 0.9996 of correlation coefficient between 1 and 100 μM, and a limit of detection (S/N = 3) was 0.2 μM. Finally, we separated rhodamine B isothiocyanate and lysine deriving from the fluorescent probe, and the result displayed that the dynamic coating method was applicable by CE separations using PDMS/glass chip.