亚硝酸根在纳米金修饰玻碳电极上的电催化氧化行为及其测定

采用直接电化学沉积法制备出纳米金修饰玻碳电极,研究了其对亚硝酸根的电催化氧化作用。结果表明,亚硝酸根在该修饰电极上于0.8 V处出现了一个良好的氧化峰。在最优实验条件下,亚硝酸根的峰电流与其浓度在2×10-6～2×10-3mol/L范围内呈一定的线性关系,检出限为6.0×10-7(S/N=3),提出了用循环伏安法测定亚硝酸根的方法。纳米金修饰电极用于东莞自来水水样中亚硝酸根的测定,回收率在98.1%～101.4%之间。对比本方法,用分光光度法对东莞自来水样中亚硝酸根进行了测定,结果满意。     

Iron nanoparticles decorated graphene-multiwalled carbon nanotubes nanocomposite-modified glassy carbon electrode for the sensitive determination of nitrite

In the present work, we described the preparation of iron nanoparticles decorated graphene-multiwalled carbon nanotubes nanocomposite (GR-MWCNTs/FeNPs) modified glassy carbon electrode (GCE) and its application for the sensitive determination of nitrite. First, GR-MWCNTs/FeNPs nanocomposite has been prepared by a simple solution-based approach via chemical reduction and then it was characterized. Afterwards, GR-MWCNTs/FeNPs/GCE was prepared and employed for the electrocatalysis of nitrite. Electrocatalytic oxidation of nitrite at the GR-MWCNTs/FeNPs/GCE has been significantly improved in terms of both reduction in overpotential and increase in peak current. Therefore, the modified electrode was employed for amperometric determination of nitrite which exhibited excellent analytical parameters with wide linear range of 1?×?10^?7 M to 1.68?×?10^?3 M and very low detection limit of 75.6 (±1.3)?nM. The proposed sensor selectively detects nitrite even in the presence of high concentration of common ions and biological interferrants. Good recoveries achieved for the determination of nitrite in various water samples reveal the promising practicality of the sensor. In addition, the sensor displays an acceptable repeatability and reproducibility along with appreciable storage and excellent operational stabilities.

A glassy carbon electrode modified with FeS nanosheets as a highly sensitive amperometric sensor for hydrogen peroxide

Iron sulfides with different atomic ratios were synthesized by a hydrothermal method and used to modify a glassy carbon electrode. The various sulfides were compared to each other for their amperometric response to H₂O₂. It is found that FeS is the most adequate material. Operated in 0.1 M NaOH solution at 0.4 V (vs. Ag/AgCl), the sensor based on FeS displays a linear response that extends from 0.50 μM to 20.5 mM of H₂O₂, with a sensitivity of 36.4 μA mM^?1 cm^?2 and a detection limit of 0.15 μM (at an S/N ratio of 3). The sensor is selective, stable and reproducible.

Open image in new window

Graphical abstract Schematic of the synthesis of pomegranate flower-like FeS by a hydrothermal route using ferric chloride and thiourea (SC(NH₂)₂) as the precursors, and ethanolamine (EA) as the structure-guiding auxiliary agent. A glassy carbon electrode (GCE) modified with this material allows for amperometric sensing of hydrogen peroxide in 0.1 M NaOH solution with a 0.15 μM detection limit. 

     

A glassy carbon electrode modified with poly(3,4-ethylenedioxythiophene) doped with nano-sized hydroxyapatite for amperometric determination of nitrite

A conducting polymer composite was prepared from nano-sized hydroxyaptite (nHAp) doped into poly(3,4-ethylenedioxythiophene) (PEDOT) and then electrodeposited on a glassy carbon electrode (GCE). The nHAp carries carboxy groups and therefore is negatively charged at moderate pH value. When doped into PEDOT (PEDOT-nHAp), it forms a uniform and stable film that exhibits low electrochemical impedance, a large specific surface, and high activity toward the electrochemical oxidation of nitrite. Under optimized conditions and at a relatively low working potential of 0.78 V (vs. SCE), the modified GCE exhibited a linear amperometric response in the 0.25 μM to 1.05 mM nitrite concentration range, and the limit of detection is as low as 83 nM.

Open image in new window

Graphical abstract A highly sensitive nitrite sensor was developed based on conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) doped with carboxyl group functionalized hydroxyapatite nanoparticles, which exhibited a large surface area and good conductivity and stability.

     

Electrochemical determination of nitrite in water samples using a glassy carbon electrode modified with didodecyldimethylammonium bromide

Multiwalled carbon nanotubes were used as solid phase extraction (SPE) adsorbent for the determination of four chloroacetanilide herbicides (alachlor, acetochlor, metolachlor and butachlor) in water. The primary factors that influence the efficiency of the SPE performance, such as the amount of the adsorbent, the eluent solvent, the pH and the sample volume, were investigated and optimized. Under optimized conditions, the recoveries of the four herbicides at three spike levels were in the range 76.7–104.4%, and the RSDs ranged from 2.5–12.7%. Good linearity was obtained for the pesticides in the concentration range 0.0025–2.5 mg L^?1, and the detection limits were 0.01–0.03 μg L^?1 at signal-to-noise ratios of 3:1. The method was successfully applied to the determination of these analytes in tap water and river water.     

A sensitive and selective nitrite sensor based on a glassy carbon electrode modified with gold nanoparticles and sulfonated graphene

We describe a highly sensitive and selective amperometric sensor for the determination of nitrite. A glassy carbon electrode was modified with a composite made from gold nanoparticles (AuNPs) and sulfonated graphene (SG). The modified electrode displays excellent electrocatalytic activity in terms of nitrite oxidation by giving much higher peak currents (at even lower oxidation overpotential) than those found for the bare electrode, the AuNPs-modified electrode, and the SG-modified electrode. The sensor has a linear response in the 10 μM to 3.96 mM concentration range, a very good detection sensitivity (45.44 μA mM^?1), and a lower detection limit of 0.2 μM of nitrite. Most common ions and many environmental organic pollutants do not interfere. The sensor was successfully applied to the determination of nitrite in water samples, and the results were found to be consistent with the values obtained by spectrophotometry.

A glassy carbon electrode modified with poly(eriochrome black T) for sensitive determination of adenine and guanine

A thin film of poly(eriochrome black T) was deposited on the surface of glassy carbon electrode by cyclic voltammetry, and this system is shown to enable the sensitive determination of adenine (A) and guanine (G). Scanning electron microscopy, Fourier transform infrared spectroscopy and electrochemical impedance spectroscopy were carried out to characterize the film which exhibits excellent electrocatalytic activity toward the oxidation of A and G in 0.1 M phosphate buffer solution (pH 4.0). Square wave voltammetry reveals an oxidation peak at 1084 mV whose current is linearly related to the concentration of A in the range from 0.05 to 1.00 μM. The oxidation peak for G occurs at 788 mV, and its current is linearly related to the concentration of G in the range from 0.025 to 1.00 μM. The detection limits are 0.017 μM for A and 0.008 μM for G (at S/N?=?3), respectively. The modified electrode displays good reproducibility and selectivity for the determination of A and G. The sensor was applied to quantify A and G in fish sperm DNA with satisfactory results.

石墨烯修饰玻碳电极伏安法测定酪氨酸

制备了石墨烯修饰玻碳电极,研究了酪氨酸在修饰电极上的电化学行为.优化了包括支持电解质、溶液pH、修饰剂用量、富集电位及时间等测定条件.在0.1 mol·L-1pH 7.0的磷酸盐缓冲溶液中,峰电流与酪氨酸的浓度在3×10-6～1.2×10-4mol·L-1的范围内呈良好的线性关系,检出限为2 × 10-7 mol·L-...     

A glassy carbon electrode modified with a polyaniline doped with silicotungstic acid and carbon nanotubes for the sensitive amperometric determination of ascorbic acid

We report on an electrochemical sensor for the sensitive amperometric determination of ascorbic acid (AA). Aniline containing suspended silicotungstic acid and carbon nanotubes was electropolymerized on the surface of a glassy carbon electrode in a single step which provides a simple and controllable method and greatly improves the electrocatalytic oxidation of AA. The effects of scan rate, solution pH and working potential were studied. A linear relationship exists between the current measured and the concentration of AA in the range from 1 μM to 10 μM and 0.01 mM to 9 mM, with a limit of detection as low as 0.51 μM (S/N?=?3). The sensor is selective, stable and satisfyingly reliable in real sample experiments. In our eyes, it has a large potential for practical applications.

Determination of nitrite with a nano-gold modified glassy carbon electrode by cyclic voltammetry

Abstract

Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) was employed to determine the concentration of rare earth elements (REEs) in plants and soils. Sample preparation and analytical conditions were investigated to set up a simple routine procedure for measuring rare earth elements. For prompt sample decomposition, a microwave digestion technique was successfully used with an acid mixture of HCl+HNO₃+HF. Detection limits, reproducibility, accuracy and possible interference were also studied. ICP-MS provided extremely low detection limits for REEs (0.6–6ng/l). Precision was typically better than 6% RSD (relative standard deviation) for soil and 10% for plant. The potential of the method was evaluated by analysis of standard reference materials of soils and plants. A good agreement between the experimental results and certified values was observed. The spectroscopic interference of Ba with Eu and light REEs(LREEs, La-Eu) with heavy REEs(HREEs, Gd-Lu) were eliminated by the algebra correction.

The results suggested that REEs in soil samples existed mainly as light REEs, and the same concentration distribution patterns of Oddo-Hakins law were observed, showing negative gradient from La to Lu concentrations. The REE contents in plants were very low, less than 20μg/g and varied with plant species. Apart from rape leaf(Brassica juncea), the REE distribution patterns in other plant leaves were consistent with soils, indicating that these plants generally absorbed REEs from soil without selectivity. Rape leaf showed selective absorption for LREEs, especially for La. The REE concentration distribution in parts of hot pepper(Capsicum annuum) was characteriaed by root>leaf>stem>fruit. The REEs absorbed by hot pepper concentrated mainly in roots and leaves, very little migrated into fruit. Transfer factors(TFs) of REEs in plants were very low. Although the contents of LREEs were relatively more than those of HREEs, no distinct difference of TFs between LREEs and HREEs was observed, meaning that LREEs and HREEs have the same abilities of transportation. However, for rape leaf, the TFs of LREEs were one or two orders of magnitude higher than those of HREEs.     

A glassy carbon electrode modified with gold nanoparticle-encapsulated graphene oxide hollow microspheres for voltammetric sensing of nitrite

Reduced graphene oxide hollow microspheres (rGO HMS) were encapsulated with gold nanoparticles (AuNPs) by spray drying. Scanning electron microscopy, transmission electron microscopy, X-ray diffraction and Raman spectroscopy were used to characterize the AuNP/rGO HMS. When placed on a glassy carbon electrode (GCE), it exhibits excellent electrochemical catalytic properties towards the oxidation of nitrite. The electrocatalytic properties were studied using various electrochemical techniques. Compared to AuNP-decorated graphene sheet based electrodes documented in the literature, the one presented here provides a larger surface area. This enhances the catalytic activity towards nitrite. The electrode, typically operated at a working potential of 0.82 V (vs. SCE), has a linear response in the 5.0 μM to 2.6 mM nitrate concentration range, and a detection limit as low as 0.5 μM (at an S/N ratio of 3).

Open image in new window

Graphical abstract Schematic presentation of the synthesis of graphene hollow microspheres encapsulated with of gold nanoparticles (AuNP/rGO HMS) through a spray drying technique. The material was applied to the electrochemical determination of nitrite.

     

A glassy carbon electrode modified with carbon dots and gold nanoparticles for enhanced electrocatalytic oxidation and detection of nitrite

The authors describe a method for the fabrication of a nanohybrid composed of carbon dots (C-dots) and gold nanoparticles (AuNPs) by in-situ reduction of C-dots and hydroauric acid under alkaline conditions. The process does not require the presence of surfactant, stabilizing agent, or reducing agent. The hybrid material was deposited in a glassy carbon electrode (GCE), and the modified GCE exhibited good electrocatalytic activity toward the oxidation of nitrite due to the synergistic effects between carbon dots and AuNPs. The findings were used to develop an amperometric sensor for nitrite. The sensor shows a linear response in the concentration range from 0.1 μmol?L^-1 to 2 mmol?L^-1 and a low detection limit of 0.06 μmol?L^-1 at the signal-to-noise ratio of 3.

Open image in new window

Graphical abstract Fabrication, characterization and electrochemical behavior of a glassy carbon electrode modifid with carbon dots and gold nanoparticles for sensing nitrite in lake water.

     

Electrochemical behavior of methyl parathion and its sensitive determination at a glassy carbon electrode modified with ordered mesoporous carbon

Ordered mesoporous carbon (OMC) was synthesized and used to modify the surface of a glassy carbon (GC) electrode. Due to the unique properties of OMC, a decrease in the overvoltage of the reduction potential of methyl parathion (MP) (to ca. 219 mV) and a 76-fold increase in the peak current are observed (compared with a bare GC electrode). The absorption capacity of the surface of the electrode for MP was determined by chronocoulometry. The results show that the Г value of the modified electrode (2.34?×?10^–9 mol cm^–2) is 9.5 times as large as that of the GC electrode (2.47?×?10^–10 mol cm^–2). The new electrode exhibits synergistic electrocatalytic and accumulative effects on MP. MP can be determined by linear sweep voltammetry (LSV) which displays a linear relationship between peak current and MP concentration in the range from 0.09 to 61 μM, with a detection limit as low as 7.6 nM (at an S/N of 3) and after an accumulation at 0 V for 5 min. The electrode was successfully applied to the determination of MP in spiked lake water samples.

Electrocatalytic reduction of nitrite at polypyrrole nanowire-platinum nanocluster modified glassy carbon electrode

Pt nanoclusters were deposited in polypyrrole (PPy) nanowires by cyclic voltammetry method, fabricating a PPy-Pt nanocomposite on glassy carbon electrode (PPy-Pt/GCE). The electrocatalytic reduction of nitrite at PPy-Pt/GCE has been investigated using 0.5 M H₂SO₄ solution. The sensor exhibited excellent electrocatalytic activity toward nitrite reduction. In acidic medium, the cyclic voltammetry at 20 mV s^− 1 gave a nitrite reduction peak at − 0.124 V with 0.566 μA μM^− 1 current sensitivity in the range of 5.0 × 10^− 7-1.0 × 10^− 3 M. The detection limit was 1.5 × 10^− 7 M (s/n = 3). The proposed method was successfully applied in the detection of nitrite in real water samples and obtained satisfactory results. The PPy-Pt composite modified electrode had good storage stability, reproducibility and anti-interference ability.     

Electrochemical determination of lead using bismuth modified glassy carbon electrode

Electrochemical application of bismuth film modified glassy carbon electrode was studied with the objective of lead detection. Bismuth film on glassy carbon substrate was formed in a plating solution of 2 mmol/L Bi(NO₃)₃, in 1 mol/L HCl at ?1.1 V (vs. Ag/AgCl) for 300 s. Lead was detected by differential pulse anodic voltammetry in acetate buffer of pH 5.0 in the concentration range of 7.5 nmol/L to 12.5 μmol/L. Factors influencing the anodic stripping performance, including deposition time, solution pH, Bi(III) concentration, potential, pulse amplitude, pulse width, have been optimized. Three linear calibration plots in the range 7.5 nmol/L to 0.1 μmol/L, 0.25 to 1 μmol/L, 2.5 to 12.5 μmol/L with regression coefficients of 0.991, 0.986 and 0.978 respectively were obtained. The theoretical detection limit equivalent to three times standard deviation for 7.5 nmol/L lead (n = 5) was calculated to be 5.25 nmol/L utilizing a 5 min deposition time and sensitivity 83.97 A L/mol. The sensitivity and detection limit of the method was compared with reported voltammetric methods for detection of lead and the result obtained was found to be promising for determination of lead.     

聚精氨酸修饰玻碳电极上多巴胺的电化学特性及其检测

用循环伏安法制备了聚精氨酸修饰玻碳电极,研究了神经递质多巴胺在该聚合物薄膜修饰电极上的电化学行为及其检测。在pH7.0的磷酸盐缓冲溶液中,多巴胺在聚精氨酸修饰电极上于0.19V和0.16V处出现一对灵敏、可逆的氧化还原峰。在最佳测试条件下,氧化峰电流与多巴胺的浓度在3.0×10-7~8.0×10-4mol/L范围内呈良好的线性关系,线性回归方程为Ipa(μA)=86.063C(mmol/L) 20.183,相关系数r=0.9993,最低检测限(3σ)5.0×10-8mol/L。用于多巴胺针剂含量的测定,结果满意。