Raman Spectroscopic Study of the Conformation and Melting of Poly(dG) · Poly(dC) and Poly(dG-dC) · Poly(dG-dC) in Aqueous Solution

Raman spectroscopic measurements on aqueous solutions of poly(dG) · poly(dC)indicate that the conformation of the polynucleotides in this double helicalcomplex are distributed between the A and B types at room temperature, the Aform being predominant at –15°C and decreasing progressively upon raising thetemperature to 65°C. A reversible pretransition has been found in this complexnear 70°C. Modifications in the spectra at this temperature indicate no majorconformational changes, but rather suggest altered base pairing and hydration ofthe carbonyl groups, accompanied by a slight distortion of the double helix,resulting in a slightly reduced stacking of the cytosine bases. Measurements inself-pressurized solutions of the complex at high temperature show that it meltsat 103°C in 0.1M NaCl solution (107°C in 0.5M NaCl). These values are somewhatlower than those we have determined in the same manner for the complexpoly(dG-dC) · poly(dG-dC): 117°C in 0.1M MgCl₂ and 113°C or higher in 0.1MNaCl solution.     

Soil and Microbial Degradation Study of Poly(ϵ-caprolactone) – Poly(vinyl butyral) Blends

Biodegradation of blends of poly(ϵ-caprolactone) [PCL] with poly(vinyl butyral) [PVB] was studied in the soil and by bacterial strains of Bacillus subtilis and Escherichia Coli isolated from the soil. Miscibility of the blends was also analyzed using FT-IR and optical microscopy at room temperature. Biodegradation of the blends was followed by weight loss, visual observations and scanning electron microscopy [SEM]. Blends with low polyester concentration, i.e., 30 wt% PCL and less, were clear and transparent and no spherulite formation was observed. Above 30 wt% PCL spherulites appeared, the size of which increased with increasing PCL concentration. Infra-red studies of the blends with less than 30 wt% PCL showed that only the amorphous phase of PCL was present. Above 30 wt% PCL indicated the presence of both crystalline and blended PCL. The second derivative of the carbonyl peak of PCL also supported the presence of two phases in blends with more than 30 wt% PCL and only one peak for blends with 30 wt% or less PCL. Weight loss was observed in all the blends. PCL rich blends showed more degradation, which was faster in the natural environment than in the laboratory. Physical appearance and microscopic examination showed the films deteriorated in soil. Blends in the Bacillus subtilis strain showed more degradation as compared to the E. Coli. strain.     

Study on the Mechanism of the Radiation-Induced Chain Oxidation of N,N,N,N-Tetramethyl-4,4′-diaminodiphenylmethane by Tetrabromomethane in Poly(vinyl chloride) Films

Kinetics and mechanism of the radiation-induced chain oxidation of N,N,N,N-tetramethyl-4,4-diaminodiphenylmethane (Am) by tetrabromomethane in poly(vinyl chloride) (PVC) films were studied by ESR and optical spectroscopy. The quantitative analysis of the ESR spectra of PVC films containing Am and CBr₄ irradiated with -rays at 77 K was performed. The nature of radical species involved in the chain process was established. It was shown that the heating of the films after their irradiation at 77 K resulted in the formation of free radicals Am^·, which initiated the chain oxidation of amine with a chain length of 100. The kinetic features of the chain oxidation–reduction reactions occurring in vacuum and in the presence of oxygen were compared.     

Adsorptive Stripping Voltammetric Study of the Enhancement of Copper(Ⅱ) by Poly(vinyl alcohol), Starch and Polyallylamine

l.IntroductionAsalatelydeveloPedsensihveandsimPleelectroanalghcalmethod,adsorptivedrippingvoltanUneto'(AdSV)receivesincreasingattenhonIl,2a].lnorgamcionscanbedetetrinedincomPlexformb}'AdSV,andmoStligandsusedaresmal1orgtricmoleculeswhichcanbeadsoIbedonthesdriceofelectrodereadily[2b]fforinStance,beryllonIIIisfitforthedetenTiltalonofboron[31.AJthoughwater-solublePOlyInerssuchasPOly(vinylalcohol)WVA)areusedasenhancingreagentSinvoltaInInetryformetalcomPlexesofotherligands[4],therearenor…     

Cure Kinetics of Poly(acrylonitrile-butadiene-styrene) Modified Epoxy–Amine System

The cure kinetics of epoxy based on the diglycidyl ether of bisphenol A (DGEBA) modified with different amounts of poly(acrylonitrile-butadiene-styrene) (ABS) and cured with 4,4′-diaminodiphenylsulfone (DDS) was investigated by employing differential scanning calorimetry (DSC). The curing reaction was followed by using an isothermal approach over the temperature range 150–180°C. The amount of ABS in the blends was 3.6, 6.9, 10 and 12.9 wt%. Blending of ABS in the epoxy monomer did not change the reaction mechanism of the epoxy network formation, but the reaction rate seems to be decreased with the addition of the thermoplastic. A phenomenological kinetic model was used for kinetic analysis. Activation energies and kinetic parameters were determined by fitting the kinetic model with experimental data. Diffusion control was incorporated to describe the cure in the latter stages, predicting the cure kinetics over the whole range of conversion. The reaction rates for the epoxy blends were found to be lower than that of the neat epoxy. The reaction rates decreased when the ABS contents was increased, due to the dilution effect caused by the ABS on the epoxy/amine reaction mixture.     

Chemical–physical behavior of hydrogels of poly(vinyl alcohol) and poly(ethylene glycol)

New hydrogels based on polyethylene glycol (PEG) and poly(vinyl alcohol) (PVA) of different degrees of hydrolysis were synthesized. To form the network the PEG was modified at their ends with acyl chloride groups to be used as the crosslinking agent. The compositions of the hydrogels were between 50% and 90% by weight of PEG and PVA of various degrees of hydrolysis were used. It was found that the degree of hydrolysis of the PVA and the PEG content influence the equilibrium water content of the hydrogel. The process of swelling of all the hydrogels prepared followed a second-order kinetics.     

Structural defects in poly(vinyl chloride)—IV. Thermal degradation of vinyl chloride/acetylene copolymers

Vinyl chloride/acetylene copolymers have been prepared under subsaturation conditions. Copolymerization rates and molecular weights of the copolymers decrease with increasing concentration of acetylene in the monomer feed, indicating that acetylene is a retarder in vinyl chloride polymerization. The concentration of internal double bonds in the copolymers determined by ozonolysis increases with increasing amount of acetylene in the feed. Thermal degradation has been performed at 110 with solid samples and at 170° in solution under inert atmosphere. The extent of HCl loss as a function of time shows a rapid initial phase followed by a slower steady rate The initial dehydrochlorination rates are higher for copolymer samples containing higher concentrations of internal double bonds. Quantitative analysis of the u.v. and visible spectra of degraded copolymers shows that the sum of the concentration of polyenes with 4–12 conjugated double bonds increases rapidly in the first phase of degradation, but then decreases slowly, due to secondary reactions of polyene sequences.     

Synergetic effect of poly(vinyl butyral) and calcium carbonate on thermal stability of poly(vinyl chloride) nanocomposites investigated by TG–FTIR–MS

In order to improve poly(vinyl chloride) (PVC) thermal stability, poly(vinyl butyral) (PVB) matrix and calcium carbonate nanoparticles were incorporated in plasticized PVC. Thermal properties of these composites were investigated by thermogravimetry analysis coupled with mass spectrometry and Fourier transform infrared spectroscopy (FTIR). This approach highlighted the efficiency of both PVB and CaCO₃ as HCl scavengers by postponing both the onset degradation temperature and the HCl release. Moreover, a synergetic effect was evidenced regarding the HCl release. Finally, kinetic parameters of the PVC first degradation stage, determined using the Flynn–Wall–Ozawa’s method, revealed a significant increase of the activation energy by incorporation of CaCO₃ in the presence or not of PVB.     

Structural defects in poly(vinyl chloride)—V. Thermal and photodegradation of copolymers of vinyl chloride with various acetylene derivatives

Vinyl chloride has been copolymerized with various acetylene derivatives in bulk at 50. It has been shown by ozonolysis that these copolymers contain a significantly increased amount of internal double bonds. A comparison of the thermal and photodegradation behaviours of the copolymers has been made. The built-in double bonds show an effect on the reactivity of the adjacent allylic chlorine depending on the electron-withdrawing or repelling nature of the substituent. Among the comonomers investigated, copolymers containing 3-chloropropine have the least reactive defect sites, because of the electron-withdrawing chloromethyl substituent. On the contrary, the electron-repelling n-butyl group, built-in by using hexine-1 as comonomer, results in enhanced reactivity of the allylic chlorines.     

IR Spectroscopic Study of Alkane Interaction with the Brønsted Acid Sites of Hydrogen-Exchanged Zeolites

Diffuse-reflectance IR spectroscopy is used to study the interaction of C₃ and C₆ alkanes (propane, n-hexane, 3-methylpentane, and cyclohexane) with the Brønsted acid sites of hydrogen-exchanged mordenite, ferrierite, ZSM-5, and faujasite. It is found that a shift of the absorption band of the stretching vibrations of acidic Si(OH)Al groups toward lower frequencies (OH) due to the formation of a hydrogen bond with adsorbed alkanes increases in the following series: OH(propane) < OH(n-hexane) = OH(3-methylpentane). The accessibility of Si(OH)Al groups to alkane molecules is determined by the dimension of rings through which molecules enter zeolite channels and cavities. It follows from the measured OH values that the strength of Brønsted acid sites decreases in the following series: HZSM-5 > H-mordenite H-ferrierite HY. The difference between the three high-silica zeolites is not great. The results obtained are compared with the published IR data on Si(OH)Al groups of zeolites with adsorbed alkanes and other weak bases.     

Relaxation Processes in Poly(vinyl alcohol)–Iodine–Potassium Iodide Supramolecular Structure

Colloid Journal - The dissipative α-relaxation process in poly(vinyl alcohol) (PVA) films and in a supramolecular composite structure resulting from the formation of ordered regions in a...     

Spectroscopic Study of Cobalt(III) β-Aminoethylate Complexes

Aqueous solutions of fac- and mer-isomers of [Co(NH₂C₂H₄O)₃] · 3H₂O were investigated by the ¹³C NMR spectroscopy method. The spectrum of the fac-isomer exhibited only two signals with 47.08 (C_N) and 63.87 (C_O) ppm, which points to a high symmetry of the compound and to the presence of a complex in the solution (unlike the crystal) with one type of polyhedron (probably, of a trigonal-prismatic type). The spectrum of the mer-isomer solution is more complicated: the C_Nand C_Osignals are split into three components with 48.81, 47.18, and 46.11 ppm and 64.70, 64.45, and 64.23 ppm, respectively. This fact confirms deterioration of the symmetry of the coordination polyhedron due to nonequivalence of -aminoethylate ions bound to the central atom. The successive protonation of the complexes does not affect either the symmetry of the coordination sphere of the fac-isomer or the asymmetry of the coordination sphere of the mer-isomer. The ¹H, ¹³C, ⁵⁹Co NMR and IR spectroscopy data made it possible to suggest that both fac-[Co(NH₂C₂H₄O)₃] fragments in the binuclear fac-[H₃(Co(NH₂C₂H₄O)₃)₂](NO₃)₃complex are linked together by three symmetrical hydrogen bridges.     

Nonenzymatic glucose sensing at ruthenium dioxide–poly(vinyl chloride)–Nafion composite electrode

Development of nonenzymatic glucose sensors with high reproducibility and stability is an urgent need to reduce cost of regular diabetic monitoring. Here, we have fabricated ruthenium dioxide–poly(vinyl chloride)–Nafion (RuO₂–PVC–Nafion) composite for direct glucose sensing in sodium hydroxide and phosphate buffer nonenzymatically for the first time. The restricted activity of the RuO₂–PVC film electrode in alkaline pH is extended to neutral pH using Nafion as an outer membrane, which reduces the distance between Ru active sites by bridging effect and improves the electrode stability. The catalytic rate, measured in terms of change of RuO₂ resistance, is similar irrespective of the medium for the high temperature annealed RuO₂ (700 °C), whereas the low temperature annealed RuO₂ (300 °C) is highly sensitive for the change in the pH of the solution. This is revealed by observing large Michaelis–Menten kinetic constant K _M for the RuO₂ (700 °C) than the low temperature annealed RuO₂ (300 °C) due to effective increase in the catalytic active sites similar to oxygen evolution reaction. Contrast to this, the buffer solution does not influence significantly the apparent K _M observed for RuO₂ (300 °C) and has greater impact on the high temperature 500 and 700 °C annealed RuO₂ samples. Cyclic voltammetry, chrono amperommetry, and electrochemical impedance spectroscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction techniques are used for characterization of the sensor behavior. The RuO₂–PVC–Nafion senses glucose selectively in the presence of potential interferences like fructose, galactose, mannose, sucrose, starch, uric acid, ascorbic acid, dopamine, and catechol in NaOH and phosphate buffer. Glucose sensing in the blood serum of the diabetic and nondiabetic patients is made. The results suggest that the RuO₂–PVC–Nafion is a promising candidate for the development of nonenzymatic glucose sensors.     

Study of simultaneous solubility of salts in the ammonium nitrate–ammonium chloride–water system

Ternary eutectic of the NH₄NO₃–NH₄Cl–H₂O system at–23.6°С has been found using a set of theoretical and experimental methods. According to the data of visual-polythermal and differential thermal analyses data, crystallization surface of the system has been plotted at–23.6 to 100°С.     

Spectroscopic and Structural Study of the 1:2 Aluminium(III) Complex of Quercetin

Quercetin (3, 3’, 4’, 5, 7-pentahydroxyflavone) is one of the most common flavonols present in nature. The complexation of Al(III) by various flavonoids has been suggested to reduce the overload of aluminum in the diet, a metal which has been implicated…     

MÖSsbauer Spectroscopic Study of Fecl3 Complexes of Poly(N-Methyl-2,5-Pyrrolylene), Poly(2,5-Thienylene), and Poly(3-Methyl-2,5-Thienylene) Prepared by Ni-Catalyzed Polycondensation

Reaction of FeCl₃ with poly(N-methyl-2,5-pyrrolylene) (PNMPy), poly(2,5-thienylene) (PTh), and poly(3-methyl-2,5-thienylene) (P3MeTh) caused reduction of FeCl₃ to afford Fe²⁺ species. Variable temperature Mössbauer spectra of the reaction systems indicated formation of FeCl₂ and FeCl^? ₄. The latter is regarded as a counter-anion for the cation delocalized along the π-conjugated polymer chain.     

Changes During Storage of Electrically Conductive Blends Polyaniline–Poly(Ethylene‐co‐vinyl Acetate)

Abstract

The electrical conductivity behavior of polyaniline–poly(ethylene‐co‐vinyl acetate) (PANI–EVA) blends was variable and dynamic during their storage. It was shown that the apparent concentration of the intrinsically conductive polymer at which a conductivity jump of the blends occurs (Φ _c ) is not a constant value over time. The electrical conductivity of the films of low PANI content (below 2.5 wt.%) increased by several (ca. 5) orders of magnitude. It was found that the PANI phase undergoes a flocculation process subsequently resulting in the formation of conductive pathways and a continuous network. Besides, the shape of percolation curves was found to change during storage of the films. Decreased conductivity deviations were registered for blends of low PANI content (<2.5 wt.%), indicating that an improvement (or decreasing number of defects) of the conductive pathways took place within the bulk of the insulating EVA matrix. These results and observed phenomena are discussed by means of the interfacial model for electrically conductive polymer blends. They supported the dispersion/flocculation phase transition within similar composite materials. The phase separation and conductivity jump are attributed to the interfacial interactions between the polymeric constituents. It was shown that the microstructure of the blends consists of highly ordered PANI paths embedded in the insulating EVA matrix. Long fibrils of PANI and interconnected fractal‐like networks were observed. It was found that the sizes of the PANI domains also varied during storage of the films. Due to the spontaneous flocculation of the primary PANI particles, conductive pathways are formed at extremely low percolation threshold (Φ _c , loading level ca. 5 × 10^?3 wt. fraction). Thus, an important property of the conductive constituent, namely its solid‐state rearrangement, was proved. This PANI self‐organization is also interpreted according to the interfacial model of polymer composites. On the other hand, the competition between self‐organization of the complex of PANI with dodecylbenzenesulfonic acid and crystallization of EVA matrix has resulted in structural changes and formation of continuous conductive networks within the blends, responsible for their significantly increased conductivity.     

Thermoreversible Gelation of Poly(vinylidene fluoride) – Camphor System

Poly (vinylidene fluoride) (PVF₂) produces thermoreversible gel in camphor when quenched to 25°C from the melt under sealed condition. The SEM micrograph of dried PVF₂/camphor gel (Wequation/tex2gif-inf-3.gif= 0.25) indicates presence of fibrillar network structure and the gels at different composition shows reversible first order phase transition. The phase diagram of the gel suggest the formation of a polymer- solvent complex. The melting enthalpy gives a stoichiometric composition of the complex at Wequation/tex2gif-inf-5.gif= 0.25. This corresponds to a molar ratio of PVF₂ monomer/camphor ≈ 4/5. Temperature-dependent synchroton experiments further support the conclusions derived from the phase diagram.