Simultaneous determination of inorganic cations and anions in capillary zone electrophoresis (CZE) with indirect fluorescence detection

Summary An instrumental configuration for the simultaneous determination of inorganic cations and anions in capillary zone electrophoresis (CZE) is described. The sample is injected into the central part of the capillary by hydrostatic injection. Indirect fluorescence detection is used. The electrolyte system consists of 2,5-dihydrobenzoate as fluorescent anion and cerium(III) as fluorescent cation. This method allows the analysis of both cations and anions without changing the electrolyte system in less than five minutes.     

Enhancement of detection sensitivity for indirect photometric detection of anions and cations in capillary electrophoresis

This review focuses on the indirect photometric detection of anions and cations by capillary electrophoresis. Special emphasis has been placed on the sensitivity of the technique and approaches taken to enhance detection limits. Theoretical considerations and requirements have been discussed, including buffering, detection sensitivity, separation of cations, and detector linearity. A series of tables detailing highly absorbing probes and the conditions of their use for indirect photometric detection are included.     

Light-emitting diode-induced fluorescence detection of native proteins in capillary electrophoresis

A continuous-wave 280 nm light-emitting diode (LED) was used as the excitation source for native fluorescence detection of proteins in CE. The operating current and temperature of the LED were optimized in order to achieve high luminescence power. It was found that a forward current of 30 mA and a temperature of approximately 5 degrees C gave the best S/N. By using a set of two ball lenses to focus light from the LED, we achieved a spot of approximately 200 mum with a power of 0.1-0.2 mW on the detection window. Fluorescence was collected with a ball lens at 90 degrees angle through a bandpass filter onto a photomultiplier tube. In CZE an LOD of 20 nM for conalbumin was reached. In capillary gel electrophoresis all eight proteins from a commercial standard kit were detected with high S/N. For a 10 microg/mL total protein mixture, S/N was better than 3 for all proteins in solution. Further improvement in LOD should be possible on utilization of an LED with higher luminescence power.     

Determination of anions with capillary electrophoresis and indirect ultraviolet detection

A method is validated for the determination of anions with capillary electrophoresis (CE) in combination with indirect UV detection. The method described here is used for the analysis of eight of the most common anions (fluoride, chloride, bromide, sulphate, nitrate, nitrite, thiosulphate and phosphate). Next, the method is compared with a another buffer system for the determination of anions with CE and indirect UV detection. Typical limits of detection are obtained between 1 and 3 mg/l for the above-mentioned compounds. The repeatability and reproducibility of the system differs per compound and is, with the exception of fluoride and phosphate, between 4 and 6% and 5–10%, respectively. Linearity was observed between 1 and 10 mg/l. The method is applied for the determination of anions in drinking water, serum and urine.     

Separation and determination of inorganic cations in beverages by capillary electrophoresis with indirect UV detection

A rapid, simple and reliable capillary electrophoresis method for the separation and quantitation of inorganic cations with indirect UV detection at 214 nm was developed. The electrolyte was: 12 mM imidazole as background absorbance provider; 5 mM malic acid and 1.0 mM 18-crown-6 ether as complexing agents; and 20% D₂O (v/v) to improve ion mobility. The pH was 4.25. The applied voltage was 22 kV at 22°C. Nine ions were completely separated and determined with correlation coefficients of 0.9979-0.9992. The relative standard deviations (RSD) were less than 0.5% for migration time and less than 5.2% for peak area (n=8). The detection limits (S/N=3) were from 0.08 mg L⁻¹ (for Na⁺) to 0.51 mg L⁻¹ (for Cu²⁺). To assess the reliability atomic absorption (AA) was also used to determine the same samples. Satisfactory results were obtained for real samples of jasmine tea drink and coconut milk.      

Simultaneous determination of selenium and antimony compounds by capillary electrophoresis with indirect fluorescence detection

Capillary electrophoresis (CE) with indirect fluorescence detection was used to analyze selenium (selenite, selenate, selenomethionine, and selenocystine) and antimony (antimonite and antimonate) compounds. The separation was achieved by CE in 6 min with a 1.2 mM fluorescein solution at pH 9.5. Fluorescein also functioned as a background fluorophore for the indirect detection of these nonfluorescent species. Linearity of more than two orders of magnitude was generally obtained. Precision of migration times and peak areas was less than 1.0% and 7.2%, respectively. The concentration limits of detection (CLODs) was in the microM range. The detection sensitivity was generally dependent upon the transfer ratio (TR, defined as the number of moles of fluorescein ions displaced by one mole of analyte ions) of each species.     

A novel method for analysis of explosives residue by simultaneous detection of anions and cations via capillary zone electrophoresis

A novel electrolyte has been developed for the simultaneous separation of cations and anions in low explosive residue by capillary electrophoresis. This electrolyte contains 15 mM α-hydroxyisobutyric acid (HIBA) as the buffer, 6 mM imidazole as the cation chromophore, 3 mM 1,3,6-naphthalenetrisulfonic acid (NTS) as the anion chromophore, 4 mM 18-crown-6 ether as a cation selectivity modifier, and 5% (v/v) acetonitrile as an organic modifier. The pH was adjusted to 6.5 using tetramethylammonium hydroxide (TMAOH), an electroosmotic flow modifier. The method was optimized by varying the concentrations of α-HIBA, imidazole, and 1,3,6-NTS at three different pH values. The results provided a simultaneous indirect photometric analysis of both anions and cations with detection limits ranging from 0.5 to 5 ppm for anions and from 10 to 15 ppm for cations with a total run time of under 7 min. The method was then applied to the analysis of Pyrodex^® RS and black powder, as well as several smokeless powders. The results obtained were consistent with previously reported results for separate anion and cation analysis and provide a faster, more complete analysis of each sample in a single chromatographic run.     

Light-emitting diode-compatible probes for indirect detection of anions in CE

A range of compounds were evaluated as probes for the indirect detection of inorganic ions using CE and light-emitting diodes (LEDs) as the light source. Emphasis was placed on examining probes likely to absorb strongly in the UV-Vis region near 350-430 nm as compounds, which absorb at longer wavelengths tend to be bulkier and adsorb onto the capillary wall. These probes should act as a replacement for the very effective but carcinogenic probe chromate. Two probes were identified and evaluated: p-nitrophenol and 4-hydroxy-3,5-dinitrobenzoic acid. The former showed the most potential with low-mobility anions, while the later had a moderate electrophoretic mobility and was more suitable for a wider mobility range of analytes. However, neither could match the efficiencies and LOD of chromate for the separation of the fast inorganic ions such as chloride, nitrate and sulphate. Nevertheless, application of the 4-hydroxy-3,5-dinitrobenzoic acid system to the determination of oxalate in Bayer liquors showed excellent sensitivity and selectivity.     

New preconditioning strategy for the determination of inorganic anions with capillary zone electrophoresis using indirect UV detection

It is widely accepted that preconditioning procedures are indispensable in capillary electrophoresis in order to achieve reproducibility of migration times and peak areas. Several preconditioning strategies have been employed for electrophoretic determinations of inorganic anions using indirect UV detection including simple flushing with buffer or alkaline or acid pre-rinsing followed by flushing with electrolyte. We investigated the influence of various preconditioning strategies on the reproducibility of migration times and peak areas of inorganic anions. The electrolyte systems for indirect UV detection were based on pyromellitic acid and chromic acid respectively as UV absorbing probes and hexamethonium hydroxide as electroosmatic flow modifier. Preconditioning agents under investigation were electrolyte buffer, NaOH, HCl and the free acids of the UV absorbing probes. Investigations showed that reproducibility of migration times and peak areas can be significantly improved by acid pre-rinsing using the corresponding acid of the UV absorbing probes compared to preconditioning by flushing the capillary with buffer. In contrast to acid pre-rinsing using hydrochloric acid no interfering signals within the migration time window of inorganic anions under investigation can be observed. The optimized preconditioning procedure yields relative standard deviations of migration times less than 0.25% (n=10). Relative standard deviations of corrected peak areas were below 5% applying acid preconditioning using pyromellitic acid.     

Method development for the determination of coumarin compounds by capillary electrophoresis with indirect laser-induced fluorescence detection

A capillary zone electrophoresis (CZE) with indirect laser-induced fluorescence detection (ILIFD) method is described for the simultaneous determination of esculin, esculetin, isofraxidin, genistein, naringin and sophoricoside. The baseline separation was achieved within 5 min with running buffer (pH 9.4) composed of 5mM borate, 20% methanol (v/v) as organic modifier, 10(-7)M fluorescein sodium as background fluorophore and 20 kV of applied voltage at 30 degrees C of cartridge temperature. Good linearity relationships (correlation coefficients >0.9900) between the second-order derivative peak-heights (RFU) and concentrations of the analytes (mol L(-1)) were obtained. The detection limits for all analytes in second-order derivative electrophoregrams were in the range of 3.8-15 microM. The RSD data of intra-day for migration times and second-order derivative peak-height were less than 0.95 and 5.02%, respectively. This developed method was applied to the analysis of the courmin compounds in herb plants with recoveries in the range of 94.7-102.1%. In this work, although the detection sensitivity was lower than that of direct LIF, yet the method would extend the application range of LIF detection.     

Application of a contactless conductometric detector for the simultaneous determination of small anions and cations by capillary electrophoresis with dual-opposite end injection

A contactless conductometric detection (CCD) system for capillary electrophoresis (CE) with a flexible detection cell was applied for the simultaneous determination of small anions and/or cations in rain, surface and drainage water samples. The applied frequency, the amplitude of the input signal, the electrolyte conductivity and electrode distance were found to be the most significant factors affecting the detection sensitivity. 2-(N-Morpholino)ethanesulfonic acid/histidine-based (MES/His) electrolytes were used for direct conductivity detection of anions and cations, while ammonium acetate was selected for indirect conductivity determination of alkylammonium salts. For the simultaneous separation procedure, involving dual-opposite end injection, an electrolyte consisting of 20 mM MES/His, 1.5 mM 18-crown-6 and 20 microM cetyltrimethylammonium bromide provided baseline separation of 13 anions and cations in less than 6 min. The detection limits achieved were 7-30 micrograms/l for direct conductometric detection of various common inorganic cations and anions, excluding F- (62 micrograms/l) and H2PO4- (250 micrograms/l), and 35-178 micrograms/l for indirect conductometric detection of alkyl ammonium cations. The developed electrophoretic method with conductometric detection was compared to ion chromatography.     

Indirect photometric detection of anions in nonaqueous capillary electrophoresis employing Orange G as probe and a light-emitting diode-based detector

A method based on indirect photometric detection (IPD) in CE employing a blue LED (473 nm) as a light source and the highly absorbing (478 nm) anionic dye, Orange G, as the probe ion was developed for the sensitive analysis of inorganic and organic anions. The use of nonaqueous solvents was examined as a simple way to reduce the adsorption of the dye onto the capillary wall and to thereby improve the baseline stability. The benefits of this approach were confirmed by experiments using BGEs in methanol (MeOH) and DMSO in which superior baselines were obtained relative to those achieved using aqueous electrolyte systems. A range of commercial LEDs was tested to improve the detection performance, with a difference of 25% in sensitivity being observed between the best and worst performing LED. The final system (4 mM Orange G, 0.05% w/v hydroxypropylcellulose (HPC), 20 mM triethanolamine (TEA) in pure MeOH) exhibited stable baselines and very low LODs (0.10-0.18 microM) for a test mixture comprising nine inorganic and organic anions. These values represent a two- to six-fold improvement over previous studies and the proposed method provides the most sensitive IPD method for the determination of anions using CE published to date. RSDs for ten replicates were in the ranges of 0.42-0.62% for migration time, 1.41-3.46% for peak area and 3.20-5.78% for peak height.     

Determination and prediction of transfer ratios for anions in capillary zone electrophoresis with indirect UV detection

Transfer ratios (i.e. the number of moles of the UV-absorbing probe anion displaced by one mole of analyte anion) were determined for the separation of inorganic and organic anions by capillary zone electrophoresis using indirect UV absorbance detection. When the electrolyte was buffered and contained only the probe anion and a single counter-cation, transfer ratios calculated from Kohlrausch theory were found to agree well with values obtained experimentally from accurately determined mobility data. However, these electrolyte systems gave long analysis times and were therefore considered impractical. More useful electrolytes were obtained by the addition of surfactants to suppress or reverse the electroosmotic flow but the co-anion introduced with the surfactant can reduce the value of the measured transfer ratio and hence adversely affect sensitivity. This problem was overcome by the use of a surfactant in the hydroxide from such as cetyltrimethylammonium hydroxide combined with a suitable buffering counter-cation such as protonated 1,3-bis[tris(hydroxymethyl)-methylamino]-propane or tris(hydroxymethyl)aminoethane. Four buffered electrolytes consisting of chromate, benzoate, phthalate, or trimellitate as probes and a suitable surfactant were used to determine transfer ratios. These systems were shown to give transfer ratios that were close to those calculated from Kohlrausch theory, thereby enabling prediction of experimental conditions giving maximum transfer ratios.     

Method development and validation for the determination of various sulfur-containing anions and other anions in the corrosion process by capillary ion electrophoresis with indirect detection

A method of capillary ion electrophoresis with indirect detection is developed for the simultaneous determination of the sulfur-containing anions S2O4(2-), S2O3(2-), SO4(2-), SO3(2-), and S2- and other anions (Cl-, Br-, NO2-, NO3-, (COO)2(2-), F-, and PO4(3-)) in the corrosion process. The effects of pH, tetradecyltrimethylammonium hydroxide, chromate, 2-[n-cyclohexylamino]-ethane sulfonate, calcium gluconate, and acetonitrile on the migration and resolution of the anions and the stability of sulfur-containing anions are systematically investigated. The detection limits, repeatability, and linearity for the anions are comparatively studied at 374, 274, and 254 nm, and the results show that 374 nm is the optimal length. The simultaneous multiwavelength detection at 374, 254, 214, and 195 nm can assist in confirming the identification of UV-absorbing anions.     

Analysis of inorganic cations in honey by capillary zone electrophoresis with indirect UV detection

An indirect UV detection method based on capillary electrophoresis was developed to separate eleven metal cations completely, including alkali, alkaline earth and transition metal, which are related to evaluate the quality of honey. The background electrolyte contains 15 mmol/L chromophore imidazole, and acetic acid (pH = 3.7), which functioned as pH adjustor and complexing reagent. The selected cations can be completely separated within 8 min under hydrodynamic mode injection with a running voltage of 20 kV at 25°C. Limit of detection, linearity, reproducibility relative standard deviation of migration time and recoveries are in the range of 0.01-0.21 mg/L, 0.06-60.0 mg/L, 2.1-3.4% and 95.4-104.1%, respectively. The applicability of the method is shown by the analysis of honey samples, including a comparison with results of pretreatment and unpretreatment of eight samples. The results demonstrate that the developed method can conveniently be used in routine analysis of honey.     

Analysis of glycosaminoglycan monosaccharides by capillary electrophoresis using indirect laser-induced fluorescence detection

Two methods for monosaccharide analysis by capillary electrophoresis (CE) using counterelectroosmotic and coelectroosmotic modes with indirect laser-induced fluorescence detection were optimised and compared. A mixture of seven glycosaminoglycan-derived hexoses was separated in alkaline fluorescein-based electrolytes and detected in both counterelectroosmotic and coelectroosmotic conditions. The fluorescein concentration and pH of the background electrolyte, and the influence of the reversal of electroosmotic flow by addition of hexadimethrine bromide on the separation were studied. Coelectroosmotic CE conditions provided better resolution and limits of detection. A 10(-6) M fluorescein solution at pH 12.25 containing 0.0005% (w/v) hexadimethrine bromide was used as background electrolyte. Quality parameters such as run-to-run, day-to-day precision and limits of detection were calculated, and better figures of merit were obtained for the coelectrooosmotic conditions than for the counterelectroosmotic mode. The coelectroosmotic method was applied to the quantitation of the hexosamine contents in glycosaminoglycans after acid hydrolysis. The method proved to be suitable for the determination of dermatan sulfate in heparin down to 2% (w/w).     

Simultaneous determination of inorganic anions and organic acids in amine solutions for sour gas treatment by capillary electrophoresis with indirect UV detection

A new CE method has been developed for the simultaneous determination of selected inorganic anions (bromide, chloride, thiosulfate, nitrite, nitrate, sulfate, thiocyanate, fluoride and phosphate) and organic acids (oxalic, malonic, formic, tartric, acetic, glycolic, propionic, butyric and cyclohexanoic) in amine solutions from sour gas treatment units. An electrolyte composed of 10 mM trimellitic acid, 200 mM Tris (pH 9.0), 0.1% polyvinyl alcohol provides a satisfactory separation of all analytes of interest. The electroosmotic flow is reversed by using hexadimethrine bromide as a semi-permanent positively charged coating, making the electrolyte free of additive. Indirect UV detection at 240 nm is used because of the weak absorbing properties of most of analytes. The addition of 1% diethanolamine in standard mixtures permits to better preserve them, inhibiting potential degradation processes, especially for thiosulfate. The quantification is performed using internal standardization, by which molybdate is used as internal standard. Moreover, the use of relative migration times and the excellent repeatabilities obtained allow unambiguous identification of analytes in real samples by comparison with standard mixture. It has been shown that no significant matrix effect came from the presence of 30% diethanolamine in amine solution samples and the developed method was characterized in terms of calibration linearity and accuracy using recovery tests. In short, the developed method allows the simultaneous and rapid determination, in difficult matrices, of numerous inorganic anions and organic acids characterized by a large range of electrophoretic mobilities.     

Peak parking technique for the simultaneous determination of anions and cations

An ion chromatography method is described for the simultaneous determination of anions (Cl^–, NO₃^–, and SO₄^2–) and cations (Na⁺, NH₄⁺, K⁺, Mg²⁺, and Ca²⁺) using a single pump, a single eluent and a single detector. An anion-exchange column modified with chondroitin sulfate C facilitated the elution of the above three anions using 5 mM tartaric acid as the eluent in isocratic mode, whereas the same eluent facilitated the separation of the above five cations on a commercially-available cation-exchange column. The separation columns were connected in series via two six-port switching valves, so the required cation-exchange or anion-exchange separation could be carried out by selecting the appropriate positions for the switching valves. The separations were completed in 30 min.     

Simultaneous separation of inorganic anions and cations by capillary zone electrophoresis

A new capillary electrophoretic approach for simultaneous separation of fast anions and cations is demonstrated. Indirect UV detection at 214 nm in conjunction with electromigration sampling from both ends of the capillary was developed. Two electrolyte systems based on imidazole-nitrate and copper(II)-ethylenediamine-nitrate were investigated for the simultaneous separation of chloride, sulphate, hydrocarbonate, potassium, ammonium, calcium, sodium and magnesium ions. Experimental parameters that were evaluated included a nature of UV chromophore, pH of electrolyte, a nature of complexing agent. The method permits the excellent separation of three anions and five cations in only 4 min using electrolyte system containing 2.5 mmol l⁻¹ Cu(NO₃)₂, 5 mmol l⁻¹ ethylenediamine and 1 mmol l⁻¹ fumaric acid at pH 8.5 adjusted with tetraethylammonium hydroxide.