石墨上纳米尺度金岛的形成

用扫描隧道显微镜研究了真空蒸镀在高定向热解石墨上金岛的形成和形状．随着蒸镀量的增加及时间的推移，金原子在表面通过扩散而逐渐合并成越来越大的原子团，以至岛，甚至岛群．虽然几个纳米大小的原子团仍十分可动，但在蒸镀量大于20单层时的岛或岛群已十分稳定．研究发现，同一蒸镀量下，各个金岛具有非常接近的宽度和高度，用薄膜成核的圆柱状模型计算岛的宽度与高度之比表明，金岛非常接近热力学平衡状态．这些形状各异的通过生长而自组装形成的纳米尺度金岛可用来进行介观物理的研究 关键词：     

Al(111)表面单个Al原子的操纵── W针尖与Al原子的相互作用

为了较清楚地阐明扫描隧道显微镜针尖在样品表面原子操纵中的具体作用，根据第一性原理的离散变分理论计算，采用“团簇模型”研究了在无外加电场下，W针尖与样品Al(111)表面Al原子的相互作用．结果表明：随着W针尖与样品表面接近到一定程度（针尖与样品表面的距离S≤10a.u.(0.53nm))时，由于针尖原子与样品表面原子的相互作用，使位于针尖正下方的表面Al原子在脱离表面时感受到一稳定的势阱，即在无外场的情况下，当W针尖与样品Al(111)表面接近到一定程度时，由于针尖的吸引作用，将使针尖正下方的Al原子自动离开样品表面而移向W针尖，实现Al(111)表面单个Al原子的操纵． 关键词：     

电场下用扫描隧道显微镜对针尖原子扩散的观察

用扫描隧道显微镜（STM）研究了在金针尖和金样品间施加大偏压时所发生的各种不同的现象．在缓变大偏压的作用下，观察到针尖原子会发生场致扩散，导致针尖形状发生变化，并且还观察到了场发射和共振隧穿现象．提出了针尖原子的场致扩散是偏压电场使针尖表面极化引起的这一机理，并且指出了这种场致扩散在用大脉冲偏压作表面加工中起着重要的作用 关键词：     

偏压在隧道效应中的作用

从隧道扫描势垒模型出发。用量子力学导出隧道电流与针尖间的偏压、间距及它们的逸出功之间的关系,并从能带模型的角度导出样品与针尖的间距不变时,隧道电流与偏压成正比关系．指出偏压的作用主要是提高针尖上电子的能量,使针尖上的电子比样品上的电子更容易穿过势垒,从而形成隧道电流．     

用扫描隧道显微镜测量局域功函数

用扫描隧道显微镜在Cu（111）-Au和Pt（111）-Ag表面上对局域功函数进行了测量．在扫描的同时通过测量隧道电流对针尖样品间距离变化的响应，可以在得到扫描隧道显微镜（STM）图的同时得到功函数图．用这种方法，成功地观察到Au，Ag覆盖层与Cu，Pt衬底间的功函数的差别．结果表明：Au覆盖层的功函数介于Cu（111）和Au（111）的功函数之间，这与其它方法的结果一致．在Pt（111）-Ag表面观察到了局域功函数随覆盖层厚度的变化．本工作表明：扫描隧道显微镜在研究功函数与表面结构的关系方面是十分有用的；用测量局域功函数的方法还可以区分表面不同种的物质 关键词：     

外电场下STM钨针尖电子结构的理论研究

采用离散变分局域密度泛函方法，研究了外电场对钨(111)面针尖电子结构的影响.详细计算和分析了在不同偏压和距离条件下，钨针尖的隧道激活轨道和电荷分布.研究结果表明：隧道激活轨道中针尖原子的成分对外偏压的极性、大小以及针尖与样品之间的距离都较敏感.与过去理论计算结果不同，钨针尖原子的5d_z²轨道对隧道激活轨道有一定贡献，但并不是最主要的.在加正偏压时对隧道激活轨道贡献最大的为5d_xz和5d_yz轨道，而在加负偏压时则为包括 关键词：     

STM针尖和外电场在Si(111)-7×7表面单原子操纵中的作用

利用第一性原理的离散变分局域密度泛函方法,采用团簇模型（Si₃₄H₃₆-W₁₁)来模拟STM操纵Si(111)-7×7表面顶角吸附原子的过程．通过分析在进行原子操纵过程中体系的能量与电子云密度分布来研究针尖和外电场的作用．结果表明,当针尖与样品间距离较近时,利用两者间有较强的相互作用,能有效地降低脱出能的能垒高度．外电场对体系脱出能的影响与其大小及极性有关,当样品上所加正偏压增强时,脱出能曲线高度单调下降,而外电场极性为负时,反而稍有增高．仅考虑针尖和样品之间的静态电子相互作用及静电场的作用,尚不能使被操纵原子脱离样品表面．最后讨论了在Si(111)-7×7表面上进行原子操纵的其他机理.     

Au表面等离子体激元激发的扫描探针电子能谱

结合扫描隧道显微镜（STM）与电子能谱仪是实现表面微区元素分析的途径之一．我们将环形电子能量分析器和三维扫描探针系统相结合,建立了一台扫描探针电子能谱仪(SPEES)．通过测量针尖近场发射束流激发的Au表面能量损失谱,我们用研究了Au原子的等离子体激元激发现象．进一步通过改变针尖－样品距离,我们研究了Au等离子体激元峰与弹性散射峰的强度比随针尖－样品距离变化的关系．研究结果发现该强度比与针尖－样品距离的关系并不是单调变化,而是在一个特定位置存在极大．     

扫描隧道显微镜功能化针尖对分子能级的选择成像

文章提出了一种通过修饰STM针尖使其功能化，调节扫描隧道显微镜（STM）的扫描偏压范围，实现对分子能级的选择性成像的方法．二萘嵌苯分子在Ag（110）表面上自组织形成的有序单层膜主要是通过分子的π电子态成像，而被二萘嵌苯分子修饰的STM针尖的能级失配于基底上吸附的分子的能级，从而只对分子的部分能级成像．这个结果为有机界面电子输运测量提供了一种更好的能级选择方法．     

室温下单个甘氨酸分子在Cu(111)表面的操纵研究

先用低能电子衍射(LEED)证明了甘氨酸(NH₂-CH₂-COOH)能在室温下在Cu单晶表面产生比较稳定的吸附，然后用扫描隧道显微镜(STM)进一步研究了其吸附情况，看到单个甘氨酸分子在Cu(111)面上吸附稳定并至少有三种吸附状态.分子操纵研究结果表明，甘氨酸分子是被针尖“推着”移动的，它在Cu(111)面有固定的吸附位，并且移动时其吸附状态可以不变.研究结果表明，甘氨酸适合做室温下小分子的可控操纵研究，并且也说明室温下小分子的可控操纵是可能的. 关键词：     

Electrical behavior of the Au/MoS2 interface studied by light emission induced by scanning tunneling microscopy

Light emitted in the tunneling junction of a scanning tunneling microscope has been used to establish the electrical characteristics of nanojunctions made of Au islands deposited on flat MoS₂ surfaces. It is shown that these characteristics are those of rectifying contacts when the gold islands are isolated and that they evolve toward those of ohmic contacts when the island density increases. It is observed that the rectifying behavior also evolves over time as on infinite metal/semiconductor contacts. Using the STM tip, single gold islands can be manipulated on the MoS₂ surface so that their electrical behavior can be changed depending on their position with regard to the other islands.     

LOCAL ELECTROCHEMICAL DEPOSITION OF METAL ISLANDS MECHANICALLY INDUCED WITH THE TIP OF AN ATOMIC FORCE MICROSCOPE

The investigation of electrochemical processes on the nanometer scale is of great scientific as well as technological interest. Here we study the electrodeposition of copper on a polycrystalline gold surface, and demonstrate that copper deposition can be locally induced by mechanical activation with the tip of an atomic force microscope (AFM). Whereas at higher values of the deposition voltage (>100mV), a solid copper film can grow on the gold surface without tip activation, at lower voltages (approx. 30-60mV), copper deposition only occurs at the position where the surface is activated by the AFM tip due to scanning in mechanical contact with the sample. With this mechano-electrochemical "writing" process, which can be performed at ambient conditions, the controlled local deposition of metallic islands is possible, at applied force loads of the order of 10nN. Both the size-dependence of the locally induced structures on the deposition time and the reversibility of the local deposition process are studied. Depending on the deposition parameters, individual copper islands between 50nm and 200nm in size were deposited at predefined locations on the gold surface. The investigations open perspectives for the controlled mechano-electrochemical writing of more complex nanostructures with the AFM tip.     

Simultaneous observation of the triangular and honeycomb structures on highly oriented pyrolytic graphite at room temperature: An STM study

Scanning tunneling microscopy (STM) was used to study the surface structures of dry-prepared and di-chloroethane-treated HOPG samples. Both triangular and honeycomb structures were simultaneously observed with the same tip at room temperature around a strand (grain boundary) on the HOPG surface. This observation did not support the tip effect in STM imaging explanation for HOPG in literature. A general layer-sliding model was utilized to explain the experimental results: sliding of the HOPG topmost layer was used to explain the origins of the triangular and honeycomb structures, and molecule intercalation into inter-layer spacing between the first and second layers of HOPG induced inhomogeneous deformation of the HOPG topmost layer that accordingly generated the Moiré patterns of the HOPG sample in di-chloroethane.     

Adsorption and manipulation of carbon onions on highly oriented pyrolytic graphite studied with atomic force microscopy

Carbon onions produced by DC arc discharge method were deposited on highly oriented pyrolytic graphite (HOPG) surface and their adsorption and manipulation was studied using an atomic force microscopy (AFM). Well-dispersed adsorption of carbon onions on HOPG surface was obtained and aggregations of onions were not observed. The van der Waals interaction between the onion and HOPG surface and that between two onions, were calculated and discussed using Hamaker's theory. The manipulation of adsorbed onions on HOPG surface was realized using the AFM in both the raster mode and the vector mode. The controllability and precision of two manipulation modes were compared and the vector mode manipulation was found superior, and is a useful technique for the construction of nano-scale devices based on carbon onions.     

Elaboration of self-organized magnetic nanoparticles by selective cobalt silicidation

Self-organized magnetic nanoparticles are obtained through selective silicidation of cobalt using a silicon substrate pre-structured with tri-dimensional gold islands as template. On the step bunches array of a vicinal Si(1 1 1) surface, gold deposition results in the formation of nanodroplets aligned along the step bunches. A subsequent cobalt deposition is performed onto this gold islands-covered Si surface, with two silicidation processes investigated: reactive deposition (RD) and solid phase reaction (SPR). The cobalt is converted into a non-magnetic silicide film except where the surface is locally masked by the gold islands, giving rise to cobalt nanomagnets which can be capped by a gold layer. A scanning tunneling microscopy comparative study of RD and SPR processes demonstrates that the former induces strong surface morphology changes while the latter preserves the pristine islands. Magnetic measurements performed with alternating gradient force magnetometry at room temperature are used to demonstrate the presence of ferromagnetic cobalt nanoparticles on SPR-processed samples. These nanomagnets show a clear in-plane anisotropy behavior.     

Effect of multiple tips on light emission induced by STM from gold nanostructures

Light emission induced by scanning tunneling microscope on gold islands grown on MoS₂ surfaces has been investigated. Surface geometry and roughness show that different apexes of the same tip can modify the energy of photons emitted in the tunneling junction. Comparisons of topography and photon map are used to locate islands imaged twice and to represent approximately the tip shape used. Light emission spectroscopy on the same island with two apexes of the multiple tip reveals variations of emission properties according to the apex used, showing the importance of tip geometry in the emission process induced by tip induced plasmon modes.     

MANIPULATION OF ATOMS, MOLECULES AND CLUSTERS FOR CONSTRUCTION OF NANOSYSTEMS

Controlled manipulations with the scanning tunneling microscope (STM) down to the scale of small molecules and single atoms allow to built molecular and atomic nanosystems, leading to the fascinating possibility of creating manmade structures on atomic scale. Here we present a short review on atomic scale manipulation investigations. Upon soft lateral manipulation of adsorbed species, in which only tip/particle forces are used, three different manipulation modes (pushing, pulling, sliding) can be discerned. We show that even the manipulation of highly coordinated native substrate atoms is possible and we demonstrate how this can be applied as local analytic and synthetic chemistry tools, with important consequences on surface structure research. Vertical manipulation of Xe and CO is demonstrated, leading to improved imaging with functionalized tips. With CO deliberately transferred to the tip, we have also succeeded to perform vibrational spectroscopy on single molecules. Furthermore, we describe how we have reproduced a full chemical reaction with single molecules, whereby all basic steps, namely preparation of the reactants, diffusion and association, are induced with the STM tip. Finally, we have extended the manipulation techniques to large specially designed molecules by performing lateral manipulation in constant height and realizing the principle of a conformational molecular switch.     

用扫描隧道显微术进行单原子操纵的机理研究

本文简要综述利用扫描隧道显微镜（ＳＴＭ）进行单原子操纵的物理机制。主要介绍了场增强的扩散、在表面上拖动（ｐｕｌｉｎｇ）推动（ｐｕｓｈｉｎｇ）原子、原子在针尖表面间接触和近接触转移、场致蒸发／脱附、隧道电子非弹性射激发和电子迁移的“电子风力”等过程。同时介绍了一些理论处理方法和对一些实验结果的解释。