Role of rare-earth element oxides in catalysts for the oxidative conversion of methane based on Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

It has been established that oxides of the rare-earth elements with moderate redox potentials (La₂O₃, CeO₂) increased the activity and working stability of Ni-Al₂O₃/cordierite catalysts in the reactions of deep and partial oxidation of methane. In the presence of the (NiO + La₂O₃ + Al₂O₃)/cordierite catalyst the process of carbon dioxide conversion of methane can be intensified by introduction of oxygen into the reaction gas mixture which decreases the temperature to achieve high conversion to 75–100 °C and has practically no effect on selectivity with respect to H₂. Translated from Teoreticheskaya i éksperimental'naya Khimiya, Vol. 44, No. 6, pp. 359–364, November–December, 2008.     

Direct analysis of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> powders by total reflection X-ray fluorescence spectrometry

A direct analysis procedure for the determination of trace impurities of Ca, V, Cr, Mn, Fe, Ni, Cu, Zn and Ga in Al₂O₃ ceramic powders by total reflection X-ray fluorescence spectrometry (TXRF) is described. The powders were analysed in the form of slurries containing 1–10 mg mL^–1 of powder. The use of the procedure in the case of powders with differing grain size and for different slurry concentrations was investigated. Three different quantification possibilities were compared, namely the use of Al as a matrix component, the use of Fe as a trace element contained in the sample or of Co added in concentrations of 200 g g^–1 as internal standard. The homogeneity of elemental distributions in sample layers deposited on the TXRF quartz carriers by evaporating 5 L of the 10 mg mL^–1 slurries was studied by scanning the 4- to 5-mm-diameter spots of two samples by synchrotron radiation TXRF at Hasylab. For powders with differing graininess but mainly finer than about a few 10 m, no systematic influence of the grain size on the accuracy of the determinations of Ca, V, Fe, Ni, Cu and Zn could be observed. The measurement precision, however, seemed to be limited by inhomogeneous distributions of the trace elements in the samples as testified by the synchrotron radiation TXRF scans. Detection limits of the developed TXRF procedure for Ca, V, Cr, Mn, Fe, Ni, Cu, Zn and Ga were found to be in the 0.3–7 g g^–1 range and were shown to increase slightly with the grain size of the samples. Quantification using Al (matrix) as internal standard led to systematically higher values out of the accuracy required, whereas the other two approaches in all cases led to reliable results.Dedicated to the memory of Wilhelm Fresenius     

Methane steam reforming over rhodium promoted Ni/Al2O3 catalysts

The effect of Rh addition upon catalyst characteristics and performance in methane steam reforming was investigated using Rh-promoted Ni/Al₂O₃ catalysts. The number of reduced metal atoms exposed on the surface increased for the Rh-promoted catalysts. Rh-promoted catalysts showed an increase in CH₄ reforming activity; however, constant turnover frequencies for promoted and unpromoted catalysts suggest that the increase in the number of metal surface atoms caused the activity enhancement. Rh also facilitated reduction of Ni/Al₂O₃.     

Two color up-conversion emissions of Er<Superscript>3+</Superscript>-doped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanopowders prepared by non-aqueous sol-gel method

Er³⁺-doped Al₂O₃ nanopowders have been prepared by the non-aqueous sol-gel method using the aluminum isopropoxide as precursor, acetylacetone as a chelating agent, nitric acid as a catalyzer, and hydrated erbium nitrate as a dopant under isopropanol environment. The different phase structure, including three crystalline types of (Al, Er)₂O₃ phases, α, γ, θ, and an Er–Al–O stoichiometric compound phase, Al₁₀Er₆O₂₄, was observed for the 0.01–0.5 mol% Er³⁺-doped Al₂O₃ nanopowders at the sintering temperature of 1,000 °C. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the ²H_11/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions of Er³⁺, were detected by a 978 nm semiconductor laser diodes excitation. With increasing Er³⁺ doping concentration from 0.01 to 0.1 mol%, the intensity of the green and red emissions increased with a decrease of the intensity ratio of the green to red emission. When the Er³⁺ doping concentration rose to 5 mol%, the intensity of the green and red emissions decreased with an increase of their intensity ratio. The maximum intensity of both the green and red emissions with the minimum of intensity ratio was obtained, respectively, for the 0.1 mol% Er³⁺-doped Al₂O₃ nanopowders composed of a single α-(Al,Er)₂O₃ phase. The intensity ratio of the green emission at 523 and 545 nm increased monotonously for all Er³⁺ doping concentrations. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er³⁺-doped Al₂O₃ nanopowders.     

Carbon dioxide reforming of methane on monolithic Ni/Al2O3-based catalysts

Nickel-alumina catalysts supported on cordierite monoliths of honeycomb structure surpass essentially the conventional granulated ones with respect to the output in carbon dioxide reforming of methane. Adjusting the surface acid-base properties of catalysts by introduction of alkali metal (Na, K) oxides inhibits the carbonization and as a result, improves the operational stability of these catalysts. An effect of promotion of nickel-alumina based composite doped by lanthanum oxide is found. This effect, caused by an additional route for the CO2 activation on Ni-La2O3/Al2O3/cordierite catalyst, is displayed in increase of methane conversion under conditions of an oxidant excess.     

Review of Ag/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Reductant System in the Selective Catalytic Reduction of NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>

Ag/Al₂O₃ is a promising catalyst for the selective catalytic reduction (SCR) by hydrocarbons (HC) of NO _x in both laboratory and diesel engine bench tests. New developments of the HC-SCR of NO _x over a Ag/Al₂O₃ catalyst are reviewed, including the efficiencies and sulfur tolerances of different Ag/Al₂O₃-reductant systems for the SCR of NO _x ; the low-temperature activity improvement of H₂-assisted HC-SCR of NO _x over Ag/Al₂O₃; and the application of a Ag/Al₂O₃-ethanol SCR system with a heavy-duty diesel engine. The discussions are focused on the reaction mechanisms of different Ag/Al₂O₃-reductant systems and H₂-assisted HC-SCR of NO _x over Ag/Al₂O₃. A SO₂-resistant surface structure in situ synthesized on Ag/Al₂O₃ by using ethanol as a reductant is proposed based on the study of the sulfate formation. These results provide new insight into the design of a high-efficiency NO _x reduction system. The diesel engine bench test results showed that a Ag/Al₂O₃-ethanol system is promising for catalytic cleaning of NO _x in diesel exhaust.     

Formation of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> bilayer using atomic layer deposition and its application to dynamic random access memory

To enhance film conformality together with electrical property suitable for dynamic random access memory (DRAM) capacitor dielectric, the effects of oxidant and post heat treatment were investigated on aluminum and titanium oxide (Al₂O₃–TiO₂) bilayer (ATO) thin film formed by atomic layer deposition method. For the conformal deposition of Al₂O₃ thin film, the O₃ oxidant required a higher deposition temperature, more than 450 °C, while H₂O or combined oxygen sources (H₂O+O₃) needed a wide range of deposition temperatures ranging from 250 to 450 °C. Conformal deposition of the TiO₂ thin film was achieved at around 325 °C regardless of the oxidants. The charge storage capacitance, measured from the ATO bilayer (4 nm Al₂O₃ and 2 nm TiO₂) deposited at 450 °C for Al₂O₃ and 325 °C for TiO₂ with O₃ oxidant on the phosphine-doped poly silicon trench, showed about 15% higher value than that of 5 nm Al₂O₃ single layer thin film without any increase of leakage current. To maintain the improved electrical property of the ATO bilayer for DRAM application, such as enhanced charge capacitance without increase of leakage current, upper electrode materials and post heat treatments after electrode formation must be selected carefully. Dedicated to Professor Su-Il Pyun on the occasion of his 65th birthday.     

X-ray photoelectron study of the interaction of H<Subscript>2</Subscript> and H<Subscript>2</Subscript>+O<Subscript>2</Subscript> mixtures on the Pt/MoO<Subscript>3</Subscript> model catalyst

The effects of H₂ and H₂ + O₂ gas mixtures of varying composition on the state of the surface of the Pt/MoO₃ model catalyst prepared by vacuum deposition of platinum on oxidized molybdenum foil were investigated by X-ray photoelectron spectroscopy (XPS) at room temperature and a pressure of 5–150 Torr. For samples with a large Pt/Mo ratio, the XP spectrum of large platinum particles showed that the effect of hydrogen-containing mixtures on the catalyst was accompanied by the reduction of molybdenum oxide. This effect results from the activation of molecular hydrogen due to the dissociation on platinum particles and subsequent spill-over of hydrogen atoms on the support. The effect was not observed at low platinum contents in the model catalyst (i.e., for small Pt particles). It is assumed for the catalyst that the loss of its hydrogen-activating ability is a consequence of the formation of platinum hydride. Possible participation of platinum hydride as intermediate in hydrogen oxidation to H₂O₂ is discussed.     

Laser assisted selective chemical metalization of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> films

Thick aluminum oxide films are prepared on Al plates by anodizing. On the ceramic surface thus obtained a very thin Ag film is deposited via vacuum thermal evaporation. The Ag/Al₂O₃/Al samples prepared are irradiated by Nd:YAG laser through a suitable metal mask in order to remove the top metal film in the exposed areas. Thus, a negative silver image of the copied mask is obtained. Further, the samples are processed in Ni electroless chemical bath activated by the rest of silver. All processing steps are studied by scanning electron microscopy (SEM). EDS X-ray mapping is applied to study the final distribution of Al and Ni in the processed areas. In addition, the DC conductivity of the fabricated Ni wires obtained is measured. The proposed new method for selective chemical deposition of electroconductive Ni onto laser microstructured Ag/Al₂O₃/Al samples is simple, versatile and not restricted to the metal/ceramic system studied as well as to the electroless deposited metal.     

Oscillations during partial oxidation of methane to synthesis gas over Ru/Al2O3 catalyst (Special column of methane transformation, Article)

Oscillations in temperatures of catalyst bed as well as concentrations of gas phase species at the exit of reactor were observed during the partial oxidation of methane to synthesis gas over Ru/Al₂O₃ in the temperature range of 600 to 850 °C. XRD, H₂-TPR and in situ Raman techniques was used to characterize the catalyst. Two types of ruthenium species, i.e. the ruthenium species weakly interacted with Al₂O₃ and that strongly interacted with the support, were identified by H₂-TPR experiment. These species are responsible for two types of oscillation profiles observed during the reaction. The oscillations were the result of these ruthenium species switching cyclically between the oxidized state and the reduced state under the reaction condition. These cyclic transformations, in turn, were the result of temperature variations caused by the varying levels of the strongly exothermic CH₄ combustion and the highly endothermic CH₄ reforming (with H₂O and CO₂) reactions (or the less exothermic direct partial oxidation of methane to CO and H₂), which were favored by the oxidized and the metallic sites, respectively. The major pathway of synthesis gas formation over the catalyst was via the combustion-reforming mechanism.     

Sol-coated preparation and characterization of macroporous α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> membrane support

A simple approach namely sol-coated technique has been developed for the low cost fabrication of macroporous ceramic under a far below common sintering temperature of alumina with large dimension grains. The prepared green support shows higher sinteractive than the one treated by wet impregnation method under the same sintering conditions. The support possesses great potential applications with 6.63–7.71 μm in pore size, 39% open porosity as well as >45 MPa mechanical strength at the sintering temperature range of 1350°– 1500°C. The results indicate that the nitrogen gas flux and pure water permeation value was 51 252.35 m³ m⁻² h⁻¹ bar⁻¹, 98.43 m³ m⁻² h⁻¹ bar⁻¹, respectively, which were more dependent on the pore structure and pore size distribution than open porosity.     

Hydrothermal synthesis and thermodynamic properties of 2CaO·3B<Subscript>2</Subscript>O<Subscript>3</Subscript>·H<Subscript>2</Subscript>O

2CaO·3B₂O₃·H₂O which has non-linear optical (NLO) property was synthesized under hydrothermal condition and identified by XRD, FTIR and TG as well as by chemical analysis. The molar enthalpy of solution of 2CaO·3B₂O₃·H₂O in HCl·54.572H₂O was determined. From a combination of this result with measured enthalpies of solution of H₃BO₃ in HCl·54.501H₂O and of CaO in (HCl+H₃BO₃) solution, together with the standard molar enthalpies of formation of CaO(s), H₃BO₃(s), and H₂O(l), the standard molar enthalpy of formation of −(5733.7±5.2) kJ mol⁻¹ of 2CaO·3B₂O₃·H₂O was obtained. Thermodynamic properties of this compound were also calculated by a group contribution method.     

Thermal oxide synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanowires

Fe₃O₄ nanorods and Fe₂O₃ nanowires have been synthesized through a simple thermal oxide reaction of Fe with C₂H₂O₄ solution at 200–600°C for 1 h in the air. The morphology and structure of Fe₃O₄ nanorods and Fe₂O₃ nanowires were detected with powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The influence of temperature on the morphology development was experimentally investigated. The results show that the polycrystals Fe₃O₄ nanorods with cubic structure and the average diameter of 0.5–0.8 μm grow after reaction at 200–500°C for 1 h in the air. When the temperature was 600°C, the samples completely became Fe₂O₃ nanowires with hexagonal structure. It was found that C₂H₂O₄ molecules had a significant effect on the formation of Fe₃O₄ nanorods. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ nanorods. Supported by the Fund of Weinan Teacher’s University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and the Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Preparation of novel visible-light-driven In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaIn<Subscript>2</Subscript>O<Subscript>4</Subscript> composite photocatalyst by sol–gel method

Novel visible-light-activated In₂O₃–CaIn₂O₄ photocatalysts were developed in this paper through a sol–gel method. The photocatalytic activities of In₂O₃–CaIn₂O₄ composite photocatalysts were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 400 nm). The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and UV–vis diffused reflectance spectroscopy (DRS). The results revealed that the In₂O₃–CaIn₂O₄ composite samples with different In₂O₃ and CaIn₂O₄ content can be obtained by controlling the synthesis temperature, and the composite photocatalysts extended the light absorption spectrum toward the visible region. The photocatalytic tests indicated that the composite samples demonstrated high visible-light activity for decomposition of methyl orange. The significant enhancement in the In₂O₃–CaIn₂O₄ photo-activity under visible light irradiation can be ascribed to the efficient separation of photo-generated carriers in the In₂O₃ and CaIn₂O₄ coupling semiconductors.     

Phase relations in the CoO–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system in subsolidus area

Thermal properties of Co₂FeV₃O₁₁ have been reinvestigated. It has been proved that this compound does not exhibit polymorphism. It melts incongruently at the temperature of 770±5°C and the phase with lyonsite type structure is the solid product of this melting. Phase relations in the whole subsolidus area of the CoO–V₂O₅–Fe₂O₃ system have been determined. The solidus area projection onto the component concentration triangle plane of this system has been constructed using the DTA and XRD methods. 15 subsidiary subsystems can be distinguished in this system.     

X-ray photoelectron spectroscopic study of the interaction of supported metal catalysts with NO<Subscript>x</Subscript>

The reactions of the platinum and rhodium model catalysts applied to aluminum oxide with NO_x (10 Torr NO + 10 Torr O₂) were studied by X-ray photoelectron spectroscopy. The reaction conducted at room temperature formed on the surface of the oxide support the NO _3,s ^? nitrate ions characterized by the N1s line at 407.4 eV and O1s line at 533.1 eV and the NO _2,s ^? nitrite ions characterized by the N1s line with a binding energy of 404.7 eV. At the same time, the Pt4f and Rh3d lines of the supported platinum particles are shifted toward higher binding energies by 0.5–1.0 eV and 0.7–1.2 eV, respectively. It is assumed that the binding energies increase due to changes in the chemical state of the platinum metal in which oxygen is dissolved. The reaction of NO_x with Pt/Al₂O₃ at 200°C forms platinum oxide defined by the Pt4f _7/2 line with a binding energy of 72.3 eV.     

Temperature dependence of the polarization resistance of the O<Subscript>2</Subscript>,Au/La<Subscript>0.88</Subscript>Sr<Subscript>0.12</Subscript>Ga<Subscript>0.82</Subscript>Mg<Subscript>0.18</Subscript>O<Subscript>2.85</Subscript> electrode system

The impedance of a porous gold electrode in contact with solid electrolyte La_0.88Sr_0.12Ga_0.82Mg_0.18O_2.85 and the effect of the manufacture conditions on its polarization resistance are studied at 600–800°C in air. The overall oxygen reaction rate on a gold electrode is described as the sum of two partial constituents, namely, the oxygen exchange at the gas/electrolyte interface at the gold/gas/electrolyte triple-phased boundary.Translated from Elektrokhimiya, Vol. 41, No. 2, 2005, pp. 190–197.Original Russian Text Copyright © 2005 by Shkerin, Sokolova, Khlupin, Beresnev.This revised version was published online in April 2005 with corrections to the article note and article title and cover date.     

Synthesis characterization and catalytic evaluation of Ni/ZrO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> aerogels catalysts

The Ni/ZrO₂/SiO₂ aerogels catalysts were synthesized via three different routes: (i) impregnation ZrO₂–SiO₂ composite aerogels with a aqueous solution of Ni(NO₃)₂, (ii) impregnation SiO₂ aerogels with a mixed aqueous solution of Ni(NO₃)₂ and ZrO(NO₃)₂ · 2H₂O, (iii) one-pot sol–gel procedure from precursors Ni(NO₃)₂/ZrO(NO₃)₂ · 2H₂O/Si(OC₂H₅)₄. These catalysts were characterized by X-ray diffraction (XRD), temperature-programmed reduction (TPR), ammonia temperature-programmed desorption (NH₃-TPD), N₂ adsorption–desorption isotherms and Fourier transform infrared (FT-IR). The Liquid-phase hydrogenation of maleic anhydride (MA) was performed over these catalysts. The results revealed that the different preparation routes result in a difference between the obtained samples, concerning the crystal structure and composition, surface acidity, mixed level of each component, texture, and catalytic selectivity.     

Sol–gel synthesis,characterization and photocatalytic activity of mesoporous TiO<Subscript>2</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3 </Subscript>granules

Mesoporous TiO₂/γ-Al₂O₃ composite granules were prepared by combining sol–gel/oil-drop method, using various titania solution. The product granules can be used as a photocatalyst or adsorbent in moving, fluidized bed reactors. The phase composition and pore structure of the granules can be controlled by calcination temperature and using different titania solution. In the photocatalysis of NH₃ decomposition, TiO₂/γ-Al₂O₃ granules using Degussa P25 powder treated thermally at 450 °C showed the highest catalytic ability. However, TiO₂/γ-Al₂O₃ granules using titania made by hydrothermal method had comparable performance in NH₃ decomposition.     

Electronic structure and chemical bonding in K<Subscript>2</Subscript>V<Subscript>3</Subscript>O<Subscript>8</Subscript>

The calculations of the electronic structure of layered polyvanadate K₂V₃O₈ were made employing the spin-polarized tight-binding LMTO method. Calculated magnetic moment for K₄V₆O₁₆ compound phase equals 1.97 μ_B. V-O interactions were established to be dominating in the chemical bonding generation in this polyvanadate according to the estimated crystal orbital overlap population. The covalent bonds V(2)-V(2) in V(2)₂O₇ groups and electron density localization on vanadium atoms in isolated pyramids V(1)O₅ were found.