制备方法对ZnO-ZrO2催化剂上乙醇转化制异丁烯反应的影响

采用恒p H值共沉淀法和非恒p H值共沉淀法制备了Zn O-Zr O2混合氧化物催化剂,考察了制备方法对乙醇转化制异丁烯反应的影响,并用低温N2吸附、X射线衍射、扫描电子显微镜、透射电子显微镜、X射线光电子能谱、拉曼光谱、紫外-可见漫反射光谱、NH3程序升温脱附和CO2程序升温脱附对催化剂进行了表征。研究结果表明,相比于非恒p H值共沉淀法制备的Zn O-Zr O2,恒p H值共沉淀法制备的Zn O-Zr O2具有较高的比表面积,更多的酸量和碱量,从而表现出更好的乙醇转化制异丁烯催化性能。在450℃和乙醇质量空速0.2 h-1的反应条件下,两种催化剂的乙醇转化率均为100%,恒p H值共沉淀法制备的催化剂的异丁烯得率为54.9%,明显高于非恒p H值共沉淀法制备的催化剂(45.7%),并且稳定性也是前者明显高于后者。     

pH值对共沉淀法制备钼基多金属氧化物催化异丁烯选择氧化制甲基丙烯醛性能的影响

研究了共沉淀法制备Mo-Bi-Fe-Co-Mn 五组分催化剂过程中溶液的pH值对催化剂中物种存在状态的影响. 并考察其异丁烯选择氧化制备甲基丙烯醛(MAL)的反应性能. 结合粉末X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、X射线光电子能谱(XPS)、氮气吸附-脱附和H₂程序升温还原(H₂-TPR)等表征手段对催化剂的结构进行了详细的研究. 结果表明, 溶液的pH值对催化剂结构和组成有明显的影响. 催化剂中某种特定物相MX随沉淀的pH值的提高而增加, 当pH=7时,催化剂中MX相的量达最大值. 此时,异丁烯的转化率和甲基丙烯醛的选择性分别为99.9%和95.6%. 进一步提高沉淀的pH值, 催化剂中MX相的量减少, 异丁烯的转化率和甲基丙烯醛的选择性也相应降低. 研究表明,催化剂上各组分间存在一定的相互作用, 催化剂中的特定物相MX是影响反应活性的关键因素之一.     

制备方法对Al2O3掺杂Pt/WO3-ZrO2催化剂上正庚烷异构化反应的影响

采用恒pH法和非恒pH法制备了Al₂O₃掺杂的Pt/WO₃/ZrO₂催化剂,并用N₂吸附-脱附、X射线衍射、紫外-可见漫反射、CO化学吸附、X射线光电子能谱、²⁷Al魔角旋转核磁共振和吡啶吸附红外等技术对催化剂进行了表征.结果表明,相比于非恒pH法制备的催化剂,恒pH法制备的催化剂具有较高的比表面积和Pt分散度,在H₂气氛中产生更多的B酸位,从而表现出更高的催化正庚烷临氢异构化反应活性; 在200℃和质量空速0.9h^-1的反应条件下,正庚烷转化率达70.0%,明显高于非恒pH法制备的催化剂(43.5%).     

制备方法对Co-MOR催化剂CH4选择还原NO性能的影响

采用离子交换法、浸渍法制备一系列的Co-MOR 催化剂, 并将其用于CH₄选择性催化还原 NO_x(CH₄-SCR)反应. 运用X 射线衍射(XRD)、X 射线荧光光谱(XRF)、扫描电子显微镜(SEM)、紫外-拉曼(UVRaman)光谱、X射线光电子能谱(XPS)、NO程序升温脱附(NO-TPD)等手段对催化剂进行了表征. 结果表明, 浸渍法制备的催化剂, Co以Co₃O₄形式存在; 而离子交换法制备的催化剂, Co以离子形式进入丝光沸石(MOR)骨架之中, 在催化剂上形成更多的Co²⁺和[Co-O-Co]²⁺, 形成更均匀NO吸附中心和CH₄-SCR反应活性中心. 催化剂活性评价表明离子交换法制备的催化剂具有更宽的活性温度区间, Co(0.30)-MOR 催化剂在327-450℃温度范围内NO转化率大于50%.     

陈化体系组成对Ce0.65Zr0.35O2储氧材料性能的影响

采用共沉淀法制备了Ce_0.65Zr_0.35O₂(CZ)储氧材料, 在传统的水陈化体系中引入了乙醇, 研究了乙醇的加入对CZ储氧材料性能的影响. 对所制备样品进行了傅里叶变换红外(FTIR)光谱、X射线光电子能谱(XPS)、粉末X射线衍射(XRD)、扫描电镜(SEM)、N₂吸附-脱附、储氧量(OSC)和H₂程序升温还原(H₂-TPR)的表征, 并考察了以CZ储氧材料为载体制备的单钯催化剂的三效性能. 结果表明, 乙醇引入陈化体系对样品的结构和性能有显著影响. 以醇水共存体系陈化制备的CZ储氧材料颗粒小、堆积松散、孔径分布宽、孔容大, 具有优异的储氧性能和热稳定性, 经1000 °C焙烧后, 比表面积为29.3 m²·g^-1, 储氧量仍高达520 μmol·g^-1. 以此为载体制备的单钯催化剂, 空燃比操作窗口宽, 对C₃H₈、CO、NO的转化明显优于水陈化体系制备的储氧材料所制备的催化剂.     

Ni-Ti-O混合氧化物的制备、表征及其富氧选择性催化还原NO

采用均匀共沉淀法制备了不同Ni/Ti摩尔比的Ni-Ti-O混合氧化物,考察了它们在富氧条件下丙烯选择性催化还原NO反应中的催化性能,并运用X射线衍射,N₂吸附-脱附、吡啶吸附、程序升温脱附和原位红外光谱对催化剂进行了表征.结果表明,Ni/Ti摩尔比为1的催化剂表现出最佳催化活性,430℃时NO_x转化率达68%.该催化剂具有锐钛矿结构,比表面积较高(149m²/g),有利于提高催化活性;其表面Lewis酸性位有利于硝酸盐物种的吸附,而硝酸盐物种是该反应的重要中间体.     

浸渍/共沉淀法对BaO改性单Pd催化剂净化甲醇汽油车尾气性能的影响

采用浸渍和共沉淀两种方法分别制备了BaO改性的Pd/CeO₂-ZrO₂-La₂O₃-Al₂O₃催化剂.运用N₂吸附-脱附,X射线衍射(XRD),H₂程序升温还原(H₂-TPR),NH₃程序升温脱附(NH₃-TPD),透射电子显微镜(TEM)和X射线光电子能谱(XPS)对催化剂进行表征,并考察其对甲醇,CO, C₃H₈ 和 NO的催化性能.活性测试结果表明,BaO的引入可明显改善Pd催化剂对甲醇,CO, C₃H₈和NO的催化活性,且浸渍法最佳,起燃温度(T₅₀)分别降低了43,31,45和35 ℃.XRD,H₂-TPR及XPS结果表明,浸渍法引入BaO主要通过表面改性方式,强化Pd-Ce界面间的相互作用,改善催化剂的还原性能,进而提高催化剂的低温活性;而共沉淀法则是通过结构改性方式增加CeO₂晶格缺陷,加速活性氧物种的流动,Ce³⁺浓度的增加是促使CO氧化活性显著提高的主要原因.     

Ce0.5+xZr0.4-xLa0.1O2-Al2O3催化剂催化燃烧柴油车碳烟

采用共沉淀法制备了系列Ce_0.5+xZr_0.4-xLa_0.1O₂-Al₂O₃催化剂, 其中0≤x≤0.4且Ce_0.5+xZr_0.4-xLa_0.1O₂与Al₂O₃的质量比为1:1. 考察了该系列催化剂对柴油车排放碳烟的催化燃烧性能, 并用低温N2吸附-脱附、X射线衍射(XRD)、X射线光电子能谱(XPS)、氢气程序升温还原(H₂-TPR)和氧气程序升温脱附(O₂-TPD)等手段对催化剂进行了表征. 研究结果表明该系列催化剂均形成了具有立方萤石结构的固溶体. 当x=0.2时, Ce³⁺离子在催化剂表面有一定的富集, 此时催化剂具有最大的β氧脱附峰和最好的表面还原性能, 同时具有良好的催化碳烟氧化活性, 碳烟在该催化剂的起燃温度为360 °C, 具有较好的应用前景.     

不同pH值制备的TiO2和TiO2/SiO2催化剂结构、表面性质及光催化活性

以TiOSO₄和SiO₂溶胶为原料, 采用沉淀法用氨水调节pH值制备TiO₂和TiO₂/SiO₂催化剂. 制备的催化剂用X射线衍射(XRD), 扫描电镜(SEM), N₂吸附(BET), 紫外-可见(UV-Vis)漫反射光谱, 程序升温脱附(NH₃-TPD), 傅里叶变换红外(FT-IR)光谱技术分析. XRD谱图显示纯TiO₂中锐钛型和金红石相共存, 且金红石相含量随pH值升高而增加. 但是, TiO₂/SiO₂催化剂只有锐钛型. 扫描电镜发现制备的催化剂呈类球形, 颗粒间相互交叠, 粒径在10-25 nm之间. TiO₂和TiO₂/SiO₂光催化剂的比表面积随pH值升高略有增大. SiO₂的添加会增大催化剂的比表面积. 程序升温脱附实验结果说明催化剂的表面酸量随pH值升高而增加. TiO₂/SiO₂的表面酸量比相同pH值制备的TiO₂大. 红外光谱分析说明Si掺杂和高pH值有利于催化剂表面生成更多的羟基. TiO₂和TiO₂/SiO₂光催化剂的催化活性随pH值升高而明显增强. TiO₂/SiO₂的光催化活性优于TiO₂. TiO₂/SiO₂催化剂具有较好的耐久性.     

表面助剂改性对Cu/ZnO/Al2O3甲醇合成催化剂性能的影响

采用共沉淀-后浸渍方法制备了表面助剂改性的Cu/ZnO/Al₂O₃ (CZA)甲醇合成催化剂, 在固定床反应器上以合成气为原料分别考察了三种助剂(Zr、Ba和Mn)对CZA催化剂性能的影响; 以Zr为助剂时反应温度的影响; 并进行了催化稳定性试验. 利用粉末X射线衍射(XRD)、低温氮气吸脱附(N₂-sorption)、氧化亚氮(N₂O)反应吸附技术、X射线光电子能谱(XPS)、氢气程序升温吸脱附(H₂-TPD)、扫描电子显微镜(SEM)和高分辨透射电子显微镜(HR-TEM)技术对催化剂进行了表征.结果显示: 以Zr或Ba作为助剂能够明显提高CZA催化剂耐热前后的甲醇时空收率(STY); Mn的引入降低了CZA催化剂的耐热前活性; Zr的引入降低了CZA催化剂最高活性温度点, 增强了CZA催化剂的催化稳定性; 还原态CZA催化剂表面Cu⁰和ZnO都能吸附活化氢气, Cu⁰与ZnO的强相互作用有利于提高催化剂的性能, 耐热后催化剂性能的降低归因于Cu晶粒的长大. 在实验和表征结果基础上,提出了CZA催化剂上合成气制甲醇的“双向同步催化反应历程”.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.