A sensitive resonance light scattering spectrometry of trace Hg with sulfur ion modified gold nanoparticles

A new resonance light scattering (RLS) spectrometric method for mercury ions (Hg²⁺) in aqueous solutions with sulfur ion (S²⁻) modified gold nanoparticles (Au-NPs-S) has been developed in this contribution. It was found that S²⁻ at the surface of Au-NPs resulting from the surface modification can interact with Hg²⁺ to form very stable S-Hg-S bonds when Hg²⁺ concentration is lower than that of S²⁻, resulting in the aggregation of Au-NPs-S and causing enhanced RLS signals. The enhanced RLS intensities (ΔI_RLS) characterized at 392 nm were found to be proportional to the concentration of Hg²⁺ in the range of 0.025-0.25 μmol L⁻¹ with a detection limit (3σ) of 0.013 μmol L⁻¹. Our results showed that this approach has excellent selectivity for Hg²⁺ over other substances in aqueous solutions.     

A colorimetric and surface-enhanced Raman scattering dual-signal sensor for Hg based on Bismuthiol II-capped gold nanoparticles

The addition of Bismuthiol II to the gold nanoparticles (AuNPs) solution led to the aggregation of AuNPs with a color change from red to blue. As a result, hot spots were formed and strong surface-enhanced Raman scattering (SERS) signal of Bismuthiol II was observed. However, the Bismuthiol II-induced aggregation of AuNPs could be reversed by Hg²⁺ in the system, accompanied by a remarkable color change from blue to red. As evidenced by UV–vis and SERS spectroscopy, the variation in absorption band and SERS intensity was strongly dependent on the concentration of Hg²⁺, suggesting a colorimetric and SERS dual-signal sensor for Hg²⁺. The sensor had a high sensitivity, low detection limits of 2 nM and 30 nM could be achieved by UV–vis spectroscopy and by SERS spectroscopy, respectively. Other environmentally relevant metal ions did not interfere with the detection of Hg²⁺. The method was successfully applied to detect Hg²⁺ in water samples. It was simple, rapid and cost-effective without any modifying or labeling procedure.     

Prussian Blue Modified Amperometric Hg2+ Ion Biosensor Based on Glucose Oxidase Inhibition

In this research a Hg²⁺ ion biosensor was developed by combining Prussian blue (PB) with glucose oxidase (GOx) – an enzyme that can be inhibited by Hg²⁺ ions. An application of PB in the design of Hg²⁺ ion biosensor enabled detecting changes in hydrogen peroxide reduction current at low operational potential of 0.2 vs Ag|AgCl,KCl_sat. The described Hg²⁺ ion biosensor exhibited wide linear range from 27 μM to 247 μM of Hg²⁺ and higher maximal detectable concentration of Hg²⁺ than other GOx inhibition-based biosensors, making it convenient for the analysis of samples with high concentration of Hg²⁺ ions.     

A self-assembled tetrapeptide that acts as a “turn-on” fluorescent sensor for Hg2+ ion

The tetrapeptide (Bz-$\mathrm{\Delta }$Phe(p-NPh₂)-l-DOPA(protected)-l-Phe-l-Phe-OMe was designed to incorporate seven phenyl rings so that it’s conformation, self-assembly and application in Hg²⁺ ions sensing could be studied. Peptide molecules adopted an overlapping β-turn of type III/III conformation in crystals. The peptide showed a highly selective turn-on response towards mercuric ion over other metal ions with a 10-fold enhancement in fluorescence intensity. This intensity change coupled with the selectivity of the peptide towards mercury allowed us to demonstrate simple colorimetric dip sensing of Hg²⁺ ions. The technique provides a highly selective and effective way to detect Hg²⁺ ions. The peptide also self-assembled into nanospheres with diameter ranges from 100 to 500?nm. Mercuric ion coordination enabled these peptide nanospheres to aggregate into well-defined nanoparticles. The enhanced fluorescence upon Hg²⁺ addition demonstrates that peptide scaffolds can be exploited in the development of different selective sensors.     

One-step assay for detecting influenza virus using dynamic light scattering and gold nanoparticles

Herein we detail the development of a simple, rapid, and sensitive method for quantitative detection of influenza A virus using dynamic light scattering (DLS) and gold nanoparticle (AuNP) labels. Influenza-specific antibodies are conjugated to AuNPs, and aggregation of the AuNP probes is induced upon addition of the target virus. DLS is used to measure the extent of aggregation and the mean hydrodynamic diameter is correlated to virus concentration. The effects of nanoparticle concentration and size on the analytical performance of the assay were systematically investigated. It was determined that decreasing the AuNP probe concentration improves the detection limit while the effect of changing the AuNP size is minimal. Optimization of the assay provided a detection limit of <100 TCID(50)/mL which is 1-2 orders of magnitude improved over commercial diagnostic kits without increasing the assay time or complexity. Additionally, this assay was demonstrated to perform equivalently for influenza virus prepared in different biological matrices.     

Highly selective light scattering imaging of chromium (III) in living cells with silver nanoparticles

In this contribution, we present a highly selective chromium ion (Cr³⁺)-induced aggregation of citrate-capped silver nanoparticles, which could be applied for the imaging of the distribution of Cr³⁺ in cells. It was found that selective aggregation of citrate-capped silver nanoparticles occurs at room temperature in the presence of Cr³⁺ in aqueous medium of pH 6.8, resulting in color change from yellow to pink in 10 min and enhanced localized surface plasmon resonance (LSPR) scattering signals. Tenfold of other metal ions including Al³⁺, Ca²⁺, Co²⁺, Cu²⁺, Fe²⁺, Fe³⁺, Hg²⁺, La³⁺, Mg²⁺, Ni²⁺, Pb²⁺, Tb³⁺ and Zn²⁺ had no response. Mechanism analysis showed that the aggregation is mainly dependent on the chelation of Cr³⁺ ion with the citrate ion capped on silver nanoparticles, forming crosslinking aggregates of silver nanoparticles. With the Cr³⁺-induced enhancement of LSPR scattering signals, Cr³⁺ in cytoplasm of human bone marrow neuroblastoma cells could be imaged with dark-field light scattering imaging technique.     

Probing the mechanism of the interaction between l‐cysteine‐capped‐CdTe quantum dots and Hg2+ using capillary electrophoresis with ensemble techniques

A good understanding of the mechanism of interaction between quantum dots (QDs) and heavy metal ions is essential for the design of more effective sensor systems. In this work, CE was introduced to explore how l ‐cysteine‐capped‐CdTe QDs (l ‐cys‐CdTe QDs) interacts with Hg²⁺. The change in electrophoretic mobility can synchronously reflect the change in the composition and property of QDs. The effects of the free and capping ligands on the system are discussed in detail. ESI‐MS, dynamic light scattering (DLS), zeta potential, and fluorescence (FL) were also applied as cooperative tools to study the interaction mechanism. Furthermore, the interaction mechanism, which principally depended on the concentration of Hg²⁺, was proposed reasonably. At the low concentration of Hg²⁺, the formation of a static complex between Hg²⁺ and the carboxyl and amino groups of l ‐cys‐CdTe QDs surface was responsible for the FL quenching. With the increase of Hg²⁺ concentration, the capping l ‐cys was stripped from the surface of l ‐cys‐CdTe QDs due to the high affinity of Hg²⁺ to the thiol group of l ‐cys. Our study demonstrates that CE can reveal the mechanism of the interaction between QDs and heavy metal ions, such as FL quenching.     

Selective fluorescent sensor for mercury ions in aqueous media using a 1,4-dihydropyridine derivative

Novel 1,4-dihydropyridine (DHP) derivatives containing 3 carboxylic acid units are synthesized via cyclotrimerization of N-substituted β-aminoacrylates followed by basic hydrolysis of the triester. These DHP derivatives are readily soluble in aqueous media buffered at pH 8.0 and the solutions give blue fluorescent signals with quantum yields of 7–23%. One of these compounds, bearing a p-methoxyphenyl N-substituted group, shows specific fluorescent quenching with the mercuric ion (Hg²⁺). The fluorescent signal of the DHP derivative decays over a period of minutes to hours depending on the Hg²⁺ concentration, which implies that the sensing mechanism involves chemical reaction between the Hg²⁺ ion and the DHP compound. The ¹H NMR and MS data suggest that Hg²⁺ mediates the oxidation of the DHP ring into a pyridinium ring. The event is useful for fluorescent detection of Hg²⁺ at the micromolar level within 30 min, with a detection limit of 0.2 μM in aqueous medium.     

Aptamer-modified AuRe Nanoalloy Probe for Trace Hg2+ Using Resonance Scattering as Detection Technique

The AuRe nanoalloy particles in molar ratio of 9:1 were prepared by sodium borohydride procedure, and modified by single strand DNA (ssDNA) to prepare an aptamer AuRe nanoprobe (AuRessDNA) for Hg²⁺. In the pH 7.0 Na₂HPO₄‐NaH₂PO₄ buffer solution and in the presence of NaCl, Hg²⁺ interacted with AuRessDNA to form double‐stranded T‐Hg²⁺‐T mismatched and release AuRe nanoparticles that aggregate to large AuRe nanoparticles clusters causing the resonance scattering (RS) peak red shifting and the RS intensity enhanced linearly. On those grounds, 0.067–33.3 nmol·L^?1 Hg²⁺ can be detected rapidly by the aptamer‐modified AuRe nanoparticles RS assay, with a detection limit of 0.04 nmol·L^?1 Hg²⁺. If the aggregated AuRe particles were removed by membrane filtration, the excess AuRessDNA in the filtration solution exhibits catalytic effect on the new Te particle reaction between Na₂TeO₄ and SnCl₂. As the concentration of Hg²⁺ increased, the AuRessDNA nanoparticles in the filtrate solution decreased, the RS intensity at 734 nm decreased linearly. The Hg²⁺ concentration (c) in the range of 0.00133–0.267 nmol·L^?1 was linear to the decreased RS intensity (ΔI_734nm), with a regression equation of ΔI= ?786.4c?4.4, a correlation coefficient of 0.9975, and a detection limit of 0.9 pmol·L^?1 Hg²⁺. This method was applied to the detection of Hg²⁺ in water samples, with satisfactory results.     

A highly sensitive sensor for Cu2+ with unmodified gold nanoparticles and DNAzyme by using the dynamic light scattering technique

Copper ion (Cu(2+)) plays an important role in many biological reactions, and a suitable level of Cu(2+) is necessary for the regular metabolism of life. Thus developing a sensitive and simple method for determination of Cu(2+) is essential. Here, a novel and sensitive Cu(2+) sensor was developed based on detecting the average hydrodynamic diameter of AuNPs by using dynamic light scattering (DLS). Cu(2+)-specific DNAzyme was double-strand and could not adsorb on the surface of AuNPs, accordingly AuNPs aggregation would occur with the addition of NaCl. However, Cu(2+) could cleave DNAzyme and release single-stranded DNA (ssDNA) fragments, which could adsorb on the surface of AuNPs and prevent them from aggregation. Such differences in DNA adsorption ability on AuNPs before and after the addition of Cu(2+) affected the disperse state of AuNPs directly, and then affected their average hydrodynamic diameter, which could be detected with the DLS technique. Based upon the above mentioned principle, detection of Cu(2+) could be realized over the range from 100 pM to 2.0 nM, with a linear regression equation of D = 306.73 - 89.66C (C: nM, R = 0.9953) and a detection limit of 60 pM (3δ/slope). Moreover, satisfactory results were obtained when the assay was applied in the detection of Cu(2+) in water samples.     

Novel Carboxylic Acid-Capped Silver Nanoparticles as Antimicrobial and Colorimetric Sensing Agents

The present work reports the synthesis, characterization, and antimicrobial activities of adipic acid-capped silver nanoparticles (AgNPs@AA) and their utilization for selective detection of Hg²⁺ ions in an aqueous solution. The AgNPs were synthesized by the reduction of Ag⁺ ions with NaBH₄ followed by capping with adipic acid. Characterization of as-synthesized AgNPs@AA was carried out by different techniques, including UV–Visible spectroscopy, Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), X-ray diffraction (XRD), Dynamic Light Scattering (DLS), and zeta potential (ZP). In the UV–Vis absorption spectrum, the characteristic absorption band for AgNPs was observed at 404 nm. The hydrodynamic size of as-synthesized AgNPs was found to be 30 ± 5.0 nm. ZP values (−35.5 ± 2.4 mV) showed that NPs possessed a negative charge due to carboxylate ions and were electrostatically stabilized. The AgNPs show potential antimicrobial activity against clinically isolated pathogens. These AgNPs were found to be selectively interacting with Hg²⁺ in an aqueous solution at various concentrations. A calibration curve was constructed by plotting concentration as abscissa and absorbance ratio (A_Control − A_Hg/A_Control) as ordinate. The linear range and limit of detection (LOD) of Hg²⁺ were 0.6–1.6 μM and 0.12 μM, respectively. A rapid response time of 4 min was found for the detection of Hg²⁺ by the nano-probe. The effect of pH and temperature on the detection of Hg²⁺ was also investigated. The nano-probe was successfully applied for the detection of Hg²⁺ from tap and river water     

Examples of the determination of molecular weight distributions by dynamic light scattering

Dynamic light scattering (DLS) is used to determine the molecular weight distributions of seven polystyrene samples in toluene at 20°C, applying a new procedure. This procedure makes possible-inter alia-the elimination of all effects due to concentration and intramolecular interference, known to be considerable for the scattering system in question. The seven samples possessed molecular weights in the range 2.5·10⁵ ? M_w ? 5·10⁶ and differing non-uniformities (= relative widths of the MWDs). The results so obtained agree well with those obtained by other experimental methods. Further, it is shown that the procedure also gives a simple and accurate means of determining whether any individual experimental DLS-curve is distorted, without any prior knowledge of the scattering system being necessary.     

Mechanism of mercury detection based on interaction of single-strand DNA and hybridized DNA with gold nanoparticles

Mechanisms of interaction of single-strand DNA and hybridized DNA on gold nanoparticles in the presence of Hg²⁺ was studied in this work. Recently the detection of Hg²⁺ using unmodified gold nanoparticles (AuNPs) combined with DNA is becoming a promising technique with the advantages of simplicity, cost-effectiveness and high sensitivity. However, few studies focused on the interaction of ssDNA and hybridized DNA on AuNPs to date. In the present work, we compared the interactions of different DNA probes on AuNPs using both absorption and fluorescence detection. It was found that there were only small partial dsDNA dissociated from the surface of AuNPs after hybridization in the presence of Hg²⁺. Moreover, we found that the aggregated AuNPs/DNA system tended to be dispersed again with increasing Hg²⁺ concentration up to 250 μM. Based on these results, the mechanisms of mercury detection based on interaction between DNA-conjugated gold nanoparticles were investigated. Positively charged dsDNA could bind to the surface of AuNPs and dominate the electrostatic interactions and consequently aggregation of the AuNPs/DNA system.     

Dynamic light scattering from asymmetric block copolymers in neutral good solvents: Evidence of association in the disordered state

Dynamic light scattering (DLS) has been used to explore the properties of asymmetric styrene-isoprene (SI) block copolymers in concentrated solutions. Concentrations were always well below those necessary to access the order–disorder transition in neutral good solvents. The samples include SI (10-50), SI (36-9), and SIS (10-100-10), where the numerical suffixes denote the block molecular weights in kilodaltons; experimental emphasis was placed on SI (10-50). The DLS intensity correlation functions in the neutral good solvents, THF and toluene, were dominated by a slow mode that first appeared at a concentration c⁺ ≈ 4 c*, where c* is the coil overlap concentration. The decay rate of this mode scaled approximately as the third power of the scattering wavevector, and the excess scattered intensity decreased with increased scattering angle. These results were tentatively ascribed to the onset of substantial concentration fluctuations, that exhibited cylindrical, or wormlike structures. Measurements in solvents of known selectivity, dioxane and cyclohexane, and on a copolymer of the opposite composition, SI (36-9), indicated that the intermolecular association was driven by the effectively repulsive interactions between styrene and isoprene segments, rather than by solvent selectivity. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1831–1837, 1998     

Using electrospray ionization mass spectrometry to explore the interactions among polythymine oligonucleotides, ethidium bromide, and mercury ions

We have used electrospray ionization mass spectrometry (ESI-MS) and fluorescence and circular dichroism (CD) spectroscopy to explore the binding of ethidium bromide (EthBr) to non-self-complementary polythymine (polyT) strands in the absence and presence of Hg²⁺ ions. In the gas phase, ESI-MS revealed that Hg²⁺ ions have greater affinity, through T-Hg²⁺-T coordination, toward polyT strands than do other metal ions. These findings are consistent with our fluorescence and CD results obtained in solution; they revealed that more T₃₃-EthBr-Hg²⁺ complexes existed upon increasing the concentrations of Hg²⁺ ions (from 0 to 50 μM). Surprisingly, the ESI-MS data indicated that the Hg²⁺ concentration dependence of the interaction between T₃₃ and EthBr is biphasic. Our ESI-MS data revealed that the T₃₃-EthBr-Hg²⁺ complexes formed with various stoichiometries depending on their relative concentrations of the components and the length of the DNA strand. When the concentrations of T₃₃/EthBr/Hg²⁺ were 5/5/2. 5 μM and 5/10/7. 5 μM, 1:1:1 and 1:1:2 T₃₃-EthBr-Hg²⁺ complexes were predominantly formed, respectively. Thus, Hg²⁺-induced DNA conformational changes clearly affect the interactions between DNA and EthBr.     

A dual-wavelength resonance light scattering ratiometry of biopolymer by its electrostatic interaction with surfactant

A dual-wavelength resonance lighting scattering (DW-RLS) ratiometry is developed to detect anion biopolymer based on their bindings with cation surfactant. Using the interaction of Hyamine 1622 (HM) with fish sperm DNA (fsDNA) as an example, a dual-wavelength resonance light scattering (DW-RLS) ratiometric method of DNA was constructed. In Britton-Robinson buffer controlled medium, fish sperm DNA (fsDNA) could interact with Hyamine 1622 (HM), displaying significantly enhanced RLS signals. By measuring the RLS signals characterized at 300.0 nm (I_300.0) and the RLS intensity ratio (I_276.0/I_294.0), respectively, fsDNA over a wide dynamic range of content could be detected. Typically, when HM concentration is kept at 6.0 × 10⁻⁵ mol l⁻¹, using I_300.0 could detect fsDNA over the range of 50-2000 ng ml⁻¹ with the limit of 3.0 ng ml⁻¹, while using I_276.0/I_294.0 could detect fsDNA over the range of 0.5-2500 ng ml⁻¹ with the limit of 0.05 ng ml⁻¹. Thus the latter so-called DW-RLS ratiometry is obviously superior to the former one. Based on the measurements of I_300.0 and I_276.0/I_294.0 data, a Scatchard plot concerning the interaction between HM and fsDNA could be constructed and thus the binding number (n) and binding constant (K) could be available with the values of 13.5 and 1.35 × 10⁵ mol⁻¹ l, and 11.9 and 1.65 × 10⁵ mol⁻¹ l, respectively.     

High-sensitivity detection of polysaccharide using phosphodiesters quaternary ammonium salt as probe by decreased resonance light scattering

Phosphodiesters quaternary ammonium salt (PQAS) displayed quite intense light scattering in aqueous solution under the optimum condition. In addition, the resonance light scattering (RLS) signal of PQAS was remarkably decreased after adding trace amount polysaccharide with the maximum peak located at 391 nm. It was found that the decreased RLS intensity of the PQAS − PPGL system (ΔI_RLS) was in proportion to PPGL concentration in the range of 0.1-30 ng mL⁻¹, with a lower detection limit of 0.05 ng mL⁻¹. Based on this rare decreased RLS phenomenon, the novel method of the determination of purified polysaccharide of Gracilaria Lemaneiformis (PPGL) at nanogram level was proposed in this contribution. The proposed approach was used to determine purified polysaccharide extracted from Gracilaria Lemaneiformis with satisfactory results. Compared with the reported polysaccharide assays, this proposed method has good selectivity, high sensitivity and is especially simple and convenient. Moreover, the mechanism of the reaction between PQAS and polysaccharide was investigated by RLS, fluorescence, and fluorescence lifetime spectra.     

A simple pyridine-based colorimetric chemosensor for highly sensitive and selective mercury(II) detection with the naked eye

Two easily-prepared pyridine-based derivatives of (Z)-2-(4-amino-phenyl)-3-(pyridine-4-yl)acrylonitrile (I)and (Z)-2-phenyl-3-(pyridin-4-yl)acrylonitrile (II) were designed, synthesised and characterised. Due to the formation of a complex with Hg²⁺, hence leading to an enhanced ICT effect, I exhibits a visible colour change from light yellow to orange, rendering it suitable for use as a naked-eye sensor for rapid detection of Hg²⁺ in an aqueous ethanol solution. When mixed with Hg²+, I interacts with Hg²⁺ in a2:1 (Y1-Hg²⁺) stoichiometry via a coordination bond with an association constant of 7.7 &#x00D7; 10⁸ M^&#x2212;2 (R² = 0.96). The present probe I exhibits excellent reproducibility, reversibility, sensitivity and selectivity with the presence of low concentration of Hg²⁺ (1.74 &#x00D7; 10^&#x2212;10 M).     

Hydrogen-bonding recognition-induced aggregation of gold nanoparticles for the determination of the migration of melamine monomers using dynamic light scattering

The migration of melamine monomers from food contact materials has aroused particular attention since the 2008 melamine-tainted milk scandal in China. However, the determination of melamine monomer’s migratory quantity (MMMQ) has remained an open question because of the complex sample pretreatment and the low sensitivity. Based on the hydrogen bonding interaction between DNA thymine and melamine, this paper described a simple and rapid method focusing on the measurement of MMMQ from melamine tableware by gold nanoparticles (GNPs) and dynamic light scattering (DLS). With the presence of probe DNA (p-DNA), the GNPs were stable in NaCl solution (0.06 M), whereas they became aggregated when the p-DNA hybridized with melamine. The change in the hydrodynamic diameter of GNPs could be detected by DLS technology. Under the optimal conditions, the average diameter increased linearly with the concentration of melamine over the range from 5.0 to 320.0 μg L⁻¹, and showed a detection limit of 2.0 μg  L⁻¹ (3σ/slope). The MMMQ was investigated within a range from 6.00 × 10⁻⁴ to 2.58 × 10⁻¹ mg dm⁻² (n ≥ 3) in four different food simulants at different temperatures and time points. The results suggest that the DLS method has great potential in the analysis of the migration of melamine monomers.     

A ratiometric electrochemical biosensor for sensitive detection of Hg based on thymine–Hg–thymine structure

In this paper, a simple, selective and reusable electrochemical biosensor for the sensitive detection of mercury ions (Hg²⁺) has been developed based on thymine (T)-rich stem–loop (hairpin) DNA probe and a dual-signaling electrochemical ratiometric strategy. The assay strategy includes both “signal-on” and “signal-off” elements. The thiolated methylene blue (MB)-modified T-rich hairpin DNA capture probe (MB-P) firstly self-assembled on the gold electrode surface via Au–S bond. In the presence of Hg²⁺, the ferrocene (Fc)-labeled T-rich DNA probe (Fc-P) hybridized with MB-P via the Hg²⁺-mediated coordination of T–Hg²⁺–T base pairs. As a result, the hairpin MB-P was opened, the MB tags were away from the gold electrode surface and the Fc tags closed to the gold electrode surface. These conformation changes led to the decrease of the oxidation peak current of MB (I_MB), accompanied with the increase of that of Fc (I_Fc). The logarithmic value of I_Fc/I_MB is linear with the logarithm of Hg²⁺ concentration in the range from 0.5 nM to 5000 nM, and the detection limit of 0.08 nM is much lower than 10 nM (the US Environmental Protection Agency (EPA) limit of Hg²⁺ in drinking water). What is more, the developed DNA-based electrochemical biosensor could be regenerated by adding cysteine and Mg²⁺. This strategy provides a simple and rapid approach for the detection of Hg²⁺, and has promising application in the detection of Hg²⁺ in real environmental samples.