YAG晶体中Cr~（3＋）→Tm~（3＋），Er~（3＋）→Tm~（3＋）的能量

研究了加入敏化离子Ｃｒ３＋和Ｅｒ３＋的Ｔｍ：ＹＡＧ晶体的吸收谱和荧光谱，计算了Ｃｒ３＋、Ｅｒ３＋、Ｔｍ３＋离子的２Ｅ、４Ｉ１３／２、３Ｆ４能态的平均寿命及能量；转移效率、转移速率．得出Ｃｒ３＋→Ｔｍ３＋转移效率为８０％，转移速率为２．１×１０３ｓ－１．由（Ｅｒ，Ｔｍ）：ＹＡＧ的荧光谱可见存在Ｅｒ３＋→Ｔｍ３＋的有效的能量转移．讨论了Ｃｒ３＋→Ｔｍ３＋和Ｅｒ３＋→Ｔｍ３＋能量转移的不同．     

敏化离子Ce~(3 )对Er~(3 )∶YAG的1.6μm波长激光性能的影响

测定了Ｃｅ３＋,Ｅｒ３＋∶ＹＡＧ中Ｃｅ３＋离子的吸收截面．用从能级跃迁速率方程和激光传输方程推出的表达式计算了１６μｍ波长激光的阈值能量（功率）和斜率效率．表明在Ｃｅ３＋,Ｅｒ３＋∶ＹＡＧ中,Ｃｅ３＋对Ｅｒ３＋离子的激光性能影响与激活离子Ｅｒ３＋的浓度、晶棒大小有关．短晶棒或浓度低的晶体加入Ｃｅ３＋可降低Ｅｒ３＋的激光阈值,增加斜率效率．而长晶棒、或Ｅｒ３＋浓度高的晶体加入Ｃｅ３＋反而增加激光阈值,减小斜率效率．     

YAG晶体中Cr4+和Yb3+的光谱和荧光特性研究

报道了（Ｃｒ＾４＋,Ｙｂ＾３＋）：ＹＡＧ晶体的吸收光谱和荧光光谱特性。在室温下,（Ｃｒ＾４＋,Ｙｂ＾３＋）：ＹＡＧ晶体在９３７ｎｍ和９６８ｎｍ处存在两个吸收带,能与ＩｎＧａＡｓ激光二级管有效耦合：而且在１０３０ｎｍ处有一Ｃｒ＾４＋吸收峰,可以实现对Ｙｂ＾３＋的自调Ｑ激光输出。（Ｃｒ＾＋,Ｙｂ＾３＋）：ＹＡＧ 荧光光谱与Ｙｂ＾３＋：ＹＡＧ晶体一样,发光中心也是位于１０２９ｎｍ,但其强度比Ｙｂ＾３＋：     

Cr~(4+): YAG被动调Q与激发态吸收饱和

运用速率方程计算了Ｃｒ４＋ＹＡＧ晶体的基态吸收、激发态吸收与入射脉冲的能量密度和强度的关系。在测量晶体透过率的实验中，发现Ｃｒ４＋ＹＡＧ晶体的激发态吸收趋于饱和。理论计算与实验数据拟合给出了包括基态吸收截面，激发态吸收截面和寿命等参数。在用Ｃｒ４＋ＹＡＧ对脉冲式ＮｄＹＡＧ激光器被动调Ｑ的实验中，得到脉宽５ｎｓ、能量９０ｍＪ的激光脉冲，并且发现这种调Ｑ与Ｃｒ４＋ＹＡＧ的激发态吸收饱和直接相关。     

Cr^4＋：YAG调Q特性的理论和实验研究

从理论和实验两个方面研究Ｃｒ＾４＋：ＹＡＧ的调Ｑ特性，测量了Ｃｒ＾４＋：ＹＡＧ调ＱＮｄ＾３＋：ＹＡＧ激光器在不同条件下脉冲能量和脉冲宽度，并与理论结果进行比较，结果显示脉冲能量的理论结果与实验结果能较发地符合，脉冲工的理论结果与实验结果变化趋势大致相一致，文中还对Ｃｒ＾４＋：ＹＡＧ调ＱＮｄ＾３＋：ＹＡＧ激光器的其它实验现象给出定性解释。     

YAG晶体中Ce^3＋对Er^3＋的敏化作用

通过求解（Ｃｅ，Ｅｒ）：ＹＡＧ和Ｅｒ：ＹＡＧ的能级跃迁速率方程，讨论了Ｃｅ＾３＋对Ｅｒ＾３＋离子的敏化作用。表明掺Ｃｅ＾３＋可增强Ｅｒ＾３＋离子１．６６μｍ波长的激光强度，但仅改变了１．６６μｍ波长激光粒子数反转，即Ｎ２（＾４Ｉ１２／２）〉Ｎ１（＾４Ｉ１５／２）与Ｅｒ＾３＋离子浓度的关系。     

Tm∶YAG晶体的光谱及激光特性研究

测试了Ｔｍ∶ＹＡＧ晶体的室温吸收光谱和荧光光谱，计算了各吸收谱线的振子强度，并根据Ｊｕｄｄ－Ｏｆｅｌｔ理论计算了Ｔｍ∶ＹＡＧ晶体的荧光跃迁截面和荧光寿命。用红宝石激光泵浦时，获得了波长２．０１μｍ、能量４０ｍＪ的激光脉冲。     

氟磷酸锶晶体Cr4+:YAG被动调Q激光特性研究

采用氙灯泵浦,实现了掺钕氟磷酸锶晶体以Ｃｒ＾４＋：ＹＡＧ作为被动调Ｑ元件的１．０５９μｍ激光运转,测量了Ｃｒ＾４＋：ＹＡＧ 同小爱过率及不同泵浦能量上激光单脉冲的输出能量、脉冲宽度、重复率,给出了Ｎｄ：Ｓ－ＦＡＰ晶体Ｃｒ＾４＋：ＹＡＧ调Ｑ工作原理的方程组,数值求解该方程组得的理论结果与实验值相符。     

钛宝石泵浦的Yb∶YAG晶体的激光性能

测量了Ｙｂ∶ＹＡＧ晶体的光谱特性,用Ａｒ＋离子泵浦钛宝石激光器作为泵浦源泵浦Ｙｂ∶ＹＡＧ晶体,采用平平腔设计,当输出耦合镜Ｔ１．０５３μｍ＝４．２６％,泵浦功率为１４１０ｍＷ时,得到３２０ｍＷ１．０５３μｍ的高效ＣＷ激光输出,斜率效率为５４％,外推阈值功率为２０３ｍＷ     

Cr^4＋：YAG的可饱和吸收特性与被动Q开关性能研究

运用速率方程计算了Ｃｒ＾４＋：ＹＡＧ晶体的可饱和吸收特性参数，包括初始吸收系数，饱和吸收系数，饱和光强和损耗调制度，用Ｃｒ＾４＋：ＹＡＧ对脉冲和连续Ｎｄ：ＹＡＧ激光器进行了被动调Ｑ，在脉冲Ｎｄ：ＹＡＧ激光器上得到了８ｎｓ的调Ｑ激光脉冲，在连续Ｎｄ：ＹＡＧ激光器的调Ｑ中得到了间隔和幅度抖动小于５％的输出脉冲充列。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.