MOVPE生长的InGaN/GaN单量子阱的光致发光和光吸收特性

研究了用金属有机物气相外延(MOVPE)法在蓝宝石衬底上生长的In组分浓度保持不变的InGaN/GaN单量子阱结构在室温下的发光特性和光吸收特性.实验结果表明,在InGaN厚度<3nm时,随着样品InGaN势阱层宽度的增加(1nm),光致发光(PL)谱的发光峰值波长出现明显的红移33nm现象,而且发光强度下降8%,谱线半峰全宽(FWHM)展宽,通过对样品的透射、反射光谱研究发现,量子阱层窄(1.5nm)的样品在波长接近红外区时出现无吸收的现象,即R+T达到了100%,而在阱层较宽的样品中没有发现这一现象,对引起这些现象的原因进行了讨论.这些结果有助于开发和优化三族氮化物半导体光电器件的进一步研究工作.     

极化效应对InGaN/GaN多量子阱结构光电特性的影响

通过求解修正的基于k·p方法的有效质量哈密顿方程并与泊松方程进行自洽,得到在极化效应影响下InGaN/GaN多量子阱的能带结构和自发辐射谱.计算结果表明,极化效应使InGaN/GaN多量子阱结构的带边由方形势变成三角形势,使导带和价带间的带隙宽度减小导致发光峰值波长红移,并使电子和空穴的分布产生空间分离从而减小发光效率...     

InGaN/GaN量子阱垒层和阱层厚度对GaN基激光器性能的影响及机理

采用LASTIP软件研究了InGaN/GaN(In组分为15%)量子阱垒层和阱层厚度对GaN基蓝紫光激光器性能的影响及机理. 模拟计算结果表明, 当阱层太薄或太厚时, GaN基激光器的阈值电流增加、输出功率下降, 最优的阱层厚度为4.0 nm左右; 当阱层厚度太薄时, 载流子很容易泄漏, 而当阱层厚度太厚时, 极化效应导致发光效率降低, 研究还发现, 与垒层厚度为7 nm 相比, 垒层厚度为15 nm时激光器的阈值电流更低、输出功率更高, 因此适当地增加垒层厚度能显著抑制载流子泄漏, 从而改善激光器性能.     

具有超晶格应力调制结构的绿光InGaN/GaN多量子阱的发光特性

研究了具有InGaN/GaN超晶格(SL)插入结构的绿光InGaN/GaN多量子阱(MQW)的发光特性。结构测试表明,SL插入结构并没有引起MQW中平均In组份的增加,而是改变了In组份的分布,形成了高In组份的量子点和低In组份量子阱。其电致发光(EL)谱和光致发光(PL)谱均出现了双发光峰。我们认为这两个 峰分别来自于量子点和量子阱,且存在着载流子从阱向点转移的输运机制。最后变温PL积分强度的Arrhenius 拟合表明,SL插入结构并没有在MQW中引入新的缺陷,使其发光效率下降。     

垒掺In提高InGaN/GaN多量子阱发光特性

利用金属有机物化学气相淀积技术在蓝宝石衬底上生长InGaN/GaN多量子阱结构.对多量子阱垒层掺In和非掺In进行了比较研究，结果表明，垒掺In 的样品界面质量变差，但明显增加了光致发光谱的峰值强度和积分强度，带边峰与黄光峰强度之比增大，降低了表面粗糙度.利用这两种结构制备了相应的发光二极管(LED)样品.通过电荧光测量可知，垒掺In的LED比非掺In的LED有较高的发光强度和相对均匀的波长，这主要是由于垒掺In后降低了阱与垒之间晶格失配的应力，从而降低了极化电场，提高了辐射复合效率. 关键词： InGaN/GaN多量子阱 X射线双晶衍射 原子力显微镜 光致发光     

InGaN/GaN多量子阱的组分确定和晶格常数计算

采用金属有机化学气相沉积(MOCVD)技术以蓝宝石为衬底在n型GaN单晶层上生长了InGaN/GaN多量子阱结构外延薄膜，利用高分辨X射线衍射(HRXRD)，卢瑟福背散射/沟道(RBS/channeling)，以及光致发光(PL)技术对InGaN/GaN多量子阱结构薄膜分别进行了平均晶格常数计算、In原子替位率计算和In组分的定量分析.研究表明：InGaN/GaN多量子阱的水平和垂直方向平均晶格常数分别为a_epi=0.3195nm，c_epi=0.5198nm，In原子的替位率为99.3%，利用HRXRD和RBS/channeling两种分析技术计算In的组分分别是0.023和0.026，并与样品生长时设定的预期目标相符合，验证了两种实验方法的准确性；而用室温条件下的光致发光谱(PL)来计算InGaN/GaN多量子阱中In的组分是与HRXRD和RBS/channeling的实验结果相差很大，说明用PL测试In组分的方法是不适宜的. 关键词： InGaN/GaN多量子阱 高分辨X射线衍射 卢瑟福背散射/沟道 光致发光     

低温近场光学显微术对InGaN/GaN多量子阱电致发光温度特性的研究

使用实验室自制的低温近场光学显微镜研究了InGaN/GaN多量子阱发光二极管在室温和液氮 温度下的近场光学像和近场光谱，发现随着温度的降低，不仅近场光学像的光强起伏大大减 小，量子阱发光峰先蓝移后红移，而且在液氮温度下在光子能量更高的位置上出现了新的发 光峰.通过对实验结果的分析，我们将这个新出现的峰归结为p-GaN层中导带底-受主能级间 跃迁形成. 关键词： InGaN/GaN多量子阱 发光二极管 近场光学 低温     

引入n型InGaN/GaN超晶格层提高量子阱特性研究

利用金属有机物化学气相淀积技术在蓝宝石衬底上生长了InGaN/GaN量子阱结构. 研究了引入n型InGaN薄层或InGaN/GaN超晶格层的量子阱特性,结果表明通过引入n型InGaN薄层或InGaN/GaN超晶格层缓解了量子阱有源区中的应力,改善了多量子阱表面形貌,减少了V型缺陷密度,而且提高了多量子阱的光致发光强度,从而也改进了LED的发光效率. 关键词： InGaN/GaN多量子阱 原子力显微镜 X射线双晶衍射 光致发光     

喷淋头高度对InGaN/GaN量子阱生长的影响

在Aixtron 3×2近耦合喷淋式金属有机化学气相沉积反应室中,调节喷淋头与基座之间的距离,制备了7,13,18,25 mm间距的4个InGaN/GaN量子阱样品。利用原子力显微镜(AFM)、X射线衍射(XRD)对样品表面形貌及界面质量进行了表征。研究表明:随着高度的增加,量子阱的表面粗糙度减少,垒/阱界面陡峭度逐步变差,垒层和阱层厚度及阱层In组分含量减少;增加高度至一定值后,量子阱厚度及In组分趋于稳定。此外,对比垒层和阱层的厚度变化,垒层厚度的变化幅度较阱层更为明显。     

InGaN/GaN多量子阱LED载流子泄漏与温度关系研究

通过测量光电流,直接观察了InGaN/GaN量子阱中载流子的泄漏程度随温度升高的变化关系。当LED温度从300K升高到360K时,在相同的光照强度下,LED的光电流增大,说明在温度上升之后,载流子从量子阱中逃逸的数目更多,即载流子泄漏比例增大。同时,光电流的增大在激发密度较低的时候更为明显,而且光电流随温度的增加幅度与激发光子的能量有关。用量子阱-量子点复合模型能很好地解释所观察到的实验现象。实验结果直接证明,随着温度的升高,InGaN/GaN量子阱中的载流子泄漏将显著增加,而且在低激发密度下这一效应更为明显。温度升高导致的载流子泄漏增多是InGaN多量子阱LED发光效率随温度升高而降低的重要原因。     

The enhancement of light-emitting efficiency using GaN-based multiple quantum well light-emitting diodes with nanopillar arrays

The quest for higher modulation speed and lower energy consumption has inevitably promoted the rapid development of semiconductor-based solid lighting devices in recent years. GaN-based light-emitting diodes （LEDs） have emerged as promising candidates for achieving high efficiency and high intensity, and have received increasing attention among many researchers in this field. In this paper, we use a self-assembled array-patterned mask to fabricate InGaN/GaN multi- quantum well （MQW） LEDs with the intention of enhancing the light-emitting efficiency. By utilizing inductively coupled plasma etching with a self-assembled Ni cluster as the mask, nanopillar arrays are formed on the surface of the InGaN/GaN MQWs. We then observe the structure of the nanopillars and find that the V-defects on the surface of the conventional structure and the negative effects of threading dislocation are effectively reduced. Simultaneously, we make a comparison of the photoluminescence （PL） spectrum between the conventional structure and the nanopillar arrays, achieved under an experimental set-up with an excitation wavelength of 325 mm. The analysis demonstrates that MQW-LEDs with nanopillar arrays achieve a PL intensity 2.7 times that of conventional LEDs. In response to the PL spectrum, some reasons are proposed for the enhancement in the light-emitting efficiency as follows： 1） the improvement in crystal quality, namely the reduction in V-defects; 2） the roughened surface effect on the expansion of the critical angle and the attenuated total reflection; and 3） the enhancement of the light-extraction efficiency due to forward scattering by surface plasmon polariton modes in Ni particles deposited above the p-type GaN layer at the top of the nanopillars.     

ZnSe／ZnS多量子阱激子光学双稳性

用MOCVD在CaF_2衬底上生长的ZnSe/ZnS多量子阱材料,在77K下用N_2激光泵浦染料获得的宽带光脉冲进行了非线性光学测量,首次观察到ZnSe/ZnS多量子阱的激子光学双稳性,据分析这是由激子的能带增宽效应引起的增强吸收光学双稳性.     

Influence of barrier thickness on the structural and optical properties of InGaN/GaN multiple quantum wells

The structural and optical properties of InGaN/GaN multiple quantum wells(MQWs) with different barrier thicknesses are studied by means of high resolution X-ray diffraction(HRXRD), a cross-sectional transmission electron microscope(TEM), and temperature-dependent photoluminescence(PL) measurements. HRXRD and cross-sectional TEM measurements show that the interfaces between wells and barriers are abrupt and the entire MQW region has good periodicity for all three samples. As the barrier thickness is increased, the temperature of the turning point from blueshift to redshift of the S-shaped temperature-dependent PL peak energy increases monotonously, which indicates that the localization potentials due to In-rich clusters is deeper. From the Arrhenius plot of the normalized integrated PL intensity, it is found that there are two kinds of nonradiative recombination processes accounting for the thermal quenching of photoluminescence,and the corresponding activation energy(or the localization potential) increases with the increase of the barrier thickness.The dependence on barrier thickness is attributed to the redistribution of In-rich clusters during the growth of barrier layers,i.e., clusters with lower In contents aggregate into clusters with higher In contents.     

Analysis of localization effect in blue-violet light emitting InGaN/GaN multiple quantum wells with different well widths

Four blue-violet light emitting InGaN/GaN multiple quantum well(MQW) structures with different well widths are grown by metal–organic chemical vapor deposition. The carrier localization effect in these samples is investigated mainly by temperature-dependent photoluminescence measurements. It is found that the localization effect is enhanced as the well width increases from 1.8 nm to 3.6 nm in our experiments. The temperature induced PL peak blueshift and linewidth variation increase with increasing well width, implying that a greater amplitude of potential fluctuation as well as more localization states exist in wider wells. In addition, it is noted that the broadening of the PL spectra always occurs mainly on the low-energy side of the PL spectra due to the temperature-induced band-gap shrinkage, while in the case of the widest well, a large extension of the spectral curve also occurs in the high energy sides due to the existence of more shallow localized centers.     

Effect of built-in electric field on electron Raman scattering in InGaN/GaN coupled quantum wells

Electron Raman scattering (ERS) in wurtzite In_xGaN_1−x/GaN coupled quantum wells (CQWs) is investigated by effective-mass approximation and second-perturbation approach, including a strong built-in electric field (BEF) effect due to the piezoelectricity and spontaneous polarization. The dependence of differential cross-section (DCS) on structural parameters of CQWs is studied. Our results show that the strong BEF gives rise to a remarkable reduction of the DCS, which is around three orders smaller than that of the CQWs without BEF. With the presence of the BEF, the emitted photon energy decreases about 10 times as a consequence of quantum-confined Stark effect.     

GaN/In_xGa_(1-x)N型最后一个量子势垒对发光二极管内量子效率的影响

GaN/In_xGa_(1-x)N型最后一个量子势垒结构能有效提高发光二极管(LED)器件内量子效率,缓解LED效率随输入电流增大而衰减的问题.本文综述了该结构及其结构变化——In组分梯度递增以及渐变、GaN/In_xGa_(1-x)N界面极化率改变等对改善LED器件性能的影响及优势,归纳总结了不同结构的GaN/In_xGa_(1-x)N型最后一个量子垒的工作机理,阐明极化反转是该结构提高LED性能的根本原因.在综述该结构发展的基础之上,通过APSYS仿真计算,进一步探索和深入分析了该结构中In_xGa_(1-x)N层的In组分及其厚度变化对LED内量子效率的影响.结果表明:In组分的增加有助于在GaN/In_xGa_(1-x)N界面产生更多的极化负电荷,增加GaN以及电子阻挡层处导带势垒高度,减少电子泄漏,从而提高LED的内量子效率;但GaN/In_xGa_(1-x)N型最后一个量子势垒中In_xGa_(1-x)N及GaN层厚度的变化由于会同时引起势垒高度和隧穿效应的改变,因而In_xGa_(1-x)N和GaN层的厚度存在一个最佳比值以实现最大化的减小漏电子,提高内量子效率.     

In源流量与Ⅲ族流量之比对InGaN/GaN多量子阱性质的影响

利用x射线三轴晶衍射和光致发光谱研究了生长参数In源流量与Ⅲ族流量之比对InGaN/GaN多量子阱结构缺陷(如位错密度和界面粗糙度)和光致发光的影响.通过对（0002）对称和（1012）非对称联动扫描的每一个卫星峰的ω扫描，分别测量出了多量子阱的螺位错和刃位错平均密度，而界面粗糙度则由（0002）对称衍射的卫星峰半高全宽随级数的变化得出.试验发现多量子阱中的位错密度特别是刃位错密度和界面粗糙度随In源流量与Ⅲ族源流量比值的增加而增加，导致室温下光致发光性质的降低，从而也证明了刃位错在InGaN/GaN 关键词： x射线三轴晶衍射 界面粗糙度 位错 InGaN/GaN多量子阱