Self-compensation characteristics of Eu ions in BaTiO3

In order to clarify whether the mixed valence of Eu²⁺/Eu³⁺ exists in a self-compensation mode in Eu-doped BaTiO₃, the site occupation and valence state of Eu ions in barium titanate were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM), electron spin resonance (ESR), Raman spectroscopy (RS), and dielectric measurements. The results indicate that Eu ions may enter both Ba- and Ti-sites as Eu³⁺, forming a self-compensation mode with the amphoteric behavior. Self-compensation characteristics of Eu ions in BaTiO₃ are reflected by an expansion in unit cell volume, evolution of the 830 cm^− 1 Raman band, strong diffusion of the dielectric peak, disappearance of the Eu²⁺ ESR broad signal, and a g = 2.004 signal independent of temperature.     

Crystal structure and photoluminescence properties of Eu-activated Ba2LiB5O10 phosphors

A novel orange-yellow-emitting Ba₂LiB₅O₁₀:Eu²⁺ phosphor has been synthesized by traditional high temperature solid state reaction. A monoclinic crystal structure of Barium lithiumborates Ba₂LiB₅O₁₀ was verified by the investigation of X-ray diffraction (XRD). The compound crystallizes in the space group of P121/m1(11) (Z = 2) with the unit cell parameters a = 4.414(1) Å, b = 14.576(2) Å, c = 6.697(2) Å and β = 104.26(2)°. Barium and lithium atoms are located in distorted octahedral and tetrahedral oxygen coordinations, respectively. Upon around 365 nm excitation, the Eu²⁺-activated Ba₂LiB₅O₁₀ phosphors exhibit a single broad emission band with the maximum at about 587 nm, due to the 4f⁶5d → 4f⁷(8S_7/2) transition of Eu²⁺. This work investigates the relationship between luminescence properties and structural characterization of the Ba₂LiB₅O₁₀: Eu²⁺. This newly developed phosphor shows high potential as a phosphor conversion for white LED applications.     

Photoluminescence and EPR studies of BaMgAl10O17:Eu phosphor with blue-emission synthesized by the solution combustion method

A blue phosphor, BaMgAl₁₀O₁₇:Eu²⁺, has been synthesized in the furnace at a temperature of 500 °C by solution combustion method. The formation of the as-prepared BaMgAl₁₀O₁₇:Eu²⁺ phosphor was confirmed by the powder X-ray diffraction technique. The EPR spectrum exhibited an intense resonance signal centered at g=4.63 at 150 mT along with a number of resonances in the vicinity of g>2.0 and g<2.0. The number of spins participating in resonance (N) and the susceptibility (c) for the resonance signal at g=4.63 have been calculated as a function of temperature. The excitation spectrum of BaMgAl₁₀O₁₇:Eu²⁺ phosphor showed a strong peak near 336 nm (4f⁷ (⁸S)→5d¹(t_2g) transition) with a staircase like structure in the region 376-400 nm owing to crystal field splitting of the Eu²⁺ d-orbital. The 336 nm excitation produced a broad blue emission at 450 nm corresponding to 4f⁶5d→4f⁷ transition. PL studies reveal the two emission centers one at 450 nm and the other at 490 nm in this phosphor.     

Novel green-emitting Na2CaPO4F:Eu phosphors for near-ultraviolet white light-emitting diodes

In this study, green-emitting Na₂CaPO₄F:Eu²⁺ phosphors were synthesized by solid-state reactions. The excitation spectra of the phosphors showed a broad hump between 250 and 450 nm; the spectra match well with the near-ultraviolet (NUV) emission spectra of light-emitting diodes (LEDs). The emission spectrum showed an intense broad emission band centered at 506 nm. White LEDs were fabricated by integrating a 390 nm NUV chip comprising blue-emitting BaMgAl₁₀O₁₇:Eu²⁺, green-emitting Na₂CaPO₄F:0.02 Eu²⁺, and red-emitting CaAlSiN₃:Eu²⁺ phosphors into a single package; the white LEDs exhibited white light with a correlated color temperature of 5540 K, a color-rendering index of 90.75, and color coordinates (0.332, 0.365) close to those of ideal white light.     

Eu-activated Ba2Mg(BO3)2 yellow-emitting phosphors for near ultraviolet-based light-emitting diodes

A series of Eu²⁺-activated Ba₂Mg(BO₃)₂ yellow phosphors were prepared by a high temperature solid-state reaction. The phosphor emits intense yellow light under near ultraviolet excitation. Large Stokes shift can be attributed to the asymmetric nature of the Eu site and the lack of rigidity in the host. The concentration self-quenching mechanism of Ba₂Mg(BO₃)₂:Eu²⁺ is d-d interaction and the critical transfer distance is calculated to be about 12.29 Å. Prototype light-emitting diodes were fabricated by coating the Ba₂Mg(BO₃)₂:0.07Eu²⁺ phosphor onto ∼370 nm-emitting InGaN chips. The LEDs exhibit intense yellow-emitting under a forward bias of 20 mA. The results indicate that Eu²⁺-activated Ba₂Mg(BO₃)₂ is a candidate as a yellow component for fabrication of near-UV white light-emitting diodes.     

Green Eu-doped Ba3Si6O12N2 phosphor for white light-emitting diodes: Synthesis, characterization and theoretical simulation

The Eu²⁺-doped Ba₃Si₆O₁₂N₂ green phosphor (Eu_xBa_3−xSi₆O₁₂N₂) was synthesized by a conventional solid state reaction method. It could be efficiently excited by UV-blue light (250-470 nm) and shows a single intense broadband emission (480-580 nm). The phosphor has a concentration quenching effect at x=0.20 and a systematic red-shift in emission wavelength with increasing Eu²⁺ concentration. High quantum efficiency and suitable excitation range make it match well with the emission of near-UV LEDs or blue LEDs. First-principles calculations indicate that Ba₃Si₆O₁₂N₂:Eu²⁺ phosphor exhibits a direct band gap, and low band energy dispersion, leading to a high luminescence intensity. The origin of the experimental absorption peaks is clearly identified based on the analysis of the density of states (DOS) and absorption spectra. The photoluminescence properties are related to the transition between 4f levels of Eu and 5d levels of both Eu and Ba atoms. The 5d energy level of Ba plays an important role in the photoluminescence of Ba₃Si₆O₁₂N₂:Eu²⁺ phosphor. The high quantum efficiency and long-wavelength excitation are mainly attributed to the existence of Ba atoms. Our results give a new explanation of photoluminescence properties and could direct future designation of novel phosphors for white light LED.     

节能灯用BaMgAl10O17:Eu2+,Mn2+荧光粉的劣化机理研究

对节能灯用BaMgAl₁₀O₁₇: Eu²⁺,Mn²⁺荧光粉的热劣化和紫外辐照劣化机理进行了对比研究. 发现热处理和紫外辐照处理均对BaMgAl₁₀O₁₇: Eu²⁺,Mn²⁺产生明显的发光劣化作用. 研究结果表明：热劣化主要涉及到Eu²⁺ 的氧化及其格位偏移, 而紫外辐照劣化与上述过程无关. 紫外辐照劣化主要源自高能紫外辐照使Eu²⁺ 处于更加不稳定的状态, 从而降低Eu²⁺ 的直接吸收和发射强度.     

Luminescent and aging characteristics of blue emitting (Ca1−x,Mgx)Al2Si2O8:Eu phosphor for PDPs application

We have evaluated thermal stability and aging property of a blue color-emitting phosphor, CaAl₂Si₂O₈:Eu²⁺ (CAS:Eu²⁺), synthesized by conventional solid-state reaction method. When both CAS:Eu²⁺ and BaMgAl₁₀O₁₉:Eu²⁺ (BAM) were baked in air at 500 °C for 20 min, the decrease of photoluminescence (PL) intensity of CAS:Eu²⁺ was lower than that of BAM. The aging property of CAS:Eu²⁺ was also better than that of BAM. Due to its rigid structure and unlimited framework of silicon-oxygen and aluminum-oxygen around Eu²⁺ ions, Eu²⁺ ions were protected from outer oxidizing atmosphere and plasma discharge. After analysis of aging property and thermal stability, the differences of these thermal stability and aging property of CAS:Eu²⁺ from those of BAM were ascribed to its crystal structure which plays a role of a shield for Eu²⁺ ions against oxidation atmosphere and Xe ion bombardment.     

Effect of Ca and Sr alkaline earth ions on luminescence properties of BaAl12O19:Eu nanophosphor

Nanosized barium aluminate materials was doped by divalent cations (Ca²⁺, Sr²⁺) and Eu²⁺ having nominal compositions Ba_1−xMxAl₁₂O₁₉:Eu (M=Ca and Sr) (x=0.1-0.5), were synthesized by the combustion method. These phosphors were characterized by XRD, scanning electron microscopy-energy-dispersive spectrometry (SEM-EDS) and photoluminescence measurement. The photoluminescence characterization showed the presence of Eu ion in divalent form which gave emission bands peaking at 444 nm for the 320 nm excitation (solid-state lighting excitation), while for 254 nm it gave the same emission wavelength of low intensity (1.5 times) compared to 320 nm excitation. It was also observed that alkaline earth metal (Ca²⁺ and Sr²⁺) dopants increase the intensity of Eu²⁺ ion in BaAl₁₂O₁₉ lattice, thus this phosphor may be useful for solid-state lighting.     

Eu red long afterglow in Y2O2S:Ti, Eu phosphor through afterglow energy transfer

Eu,Ti co-doped Y₂O₂S:0.03Ti,0.03Eu phosphors and single Eu or Ti doped Y₂O₂S phosphors were prepared and their luminescent properties were investigated in detail by photoluminescence (PL) spectra, long afterglow spectra and thermoluminescence spectra measurements. The results showed that Y₂O₂S:Ti,Eu phosphors possess orange-red afterglow color with afterglow time above 5 h. The reddish afterglow color, which corresponds to a set of linear Eu³⁺ emissions at low-energy range (540-630 nm), was demonstrated to come from the energy transfer process from yellow Ti afterglow emissions, the proposed energy transfer mechanism may well explain the Eu³⁺ afterglow emission.     

Enhanced blue emission and EPR study of LaMgAl11O19:Eu phosphors

Europium doped LaMgAl₁₁O₁₉ phosphor was prepared by the combustion method. The as-prepared and post-treated (1350 °C 10 h 5% H₂+95% N₂) phosphors were investigated by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), photoluminescence (PL) and electron paramagnetic resonance (EPR) techniques. XRD patterns show that LaMgAl₁₁O₁₉:Eu phosphors have hexagonal structure. FT-IR spectrum exhibits absorption bands corresponding to the stretching vibration of AlO₄ and AlO₆. Morphological studies reveal that this phosphor has faceted plates of varying sizes and shapes. The as-prepared LaMgAl₁₁O₁₉:Eu phosphor consists of both Eu³⁺ and Eu²⁺ ions. The phosphor exhibits a bright blue emission at 450 nm (4f⁶5d→4f⁷ transition of Eu²⁺). On post-treating the phosphor we are able to enhance the blue emission efficiency by 330%. The process was detected from the evolution of excitation, emission and EPR spectra and the results are discussed.     

Eu/Tb ions co-doped white light luminescence Y2O3 phosphors

Y₂O₃:Eu³⁺, Tb³⁺ phosphors with white emission are prepared with different doping concentration of Eu³⁺ and Tb³⁺ ions and synthesizing temperatures from 750 to 950 °C by the co-precipitation method. The resulted phosphors were characterized by X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy. The results of XRD indicate that the crystallinity of the synthesized samples increases with enhancing the firing temperature. The photoluminescence spectra indicate the Eu³⁺ and Tb³⁺ co-doped Y₂O₃ phosphors show five main emission peaks: three at 590, 611 and 629 nm originate from Eu³⁺ and two at 481 and 541 nm originate from Tb³⁺, under excitation of 250-320 nm irradition. The white light luminescence color could be changed by varying the excitation wavelength. Different concentrations of Eu³⁺ and Tb³⁺ ions were induced into the Y₂O₃ lattice and the energy transfer from Tb³⁺→Eu³⁺ ions in these phosphors was found. The Commission International de l’Eclairage (CIE) chromaticity shows that the Y₂O₃:Eu³⁺, Tb³⁺ phosphors can obtain an intense white emission.     

Characterization of the VUV excitation spectrum of BaZr(BO3)2:Eu

The excitation spectra of M (M=Si⁴⁺, Ti⁴⁺) and Eu³⁺ co-doped BaZr(BO₃)₂, BaZrO₃:Eu and La₂Zr₂O₇:Eu in the vacuum ultraviolet (VUV) regions of 110-300 nm are investigated and the host-lattice absorption are characterized. The result indicated that BaZr(BO₃)₂:Eu³⁺ phosphor has a strong absorption under the VUV excitation, and in the host-lattice excitation, the strong band at 130-160 nm could be due to the BO₃ atomic groups; the band at 160-180 nm is related to the excitation of Ba-O; 180-200 nm corresponds to the charge transfer (CT) transition of Zr-O. The band at 200-235 nm due to the CT band of Eu³⁺-O²⁻ and a bond valence study explained the observed weak CT band of Eu³⁺-O²⁻ in the excitation spectra of BaZr(BO₃)₂:Eu³⁺. The emission results show that Si⁴⁺ can sensitize luminescence in the host of BaZr(BO₃)₂:Eu but Ti⁴⁺ has no improvement effect on luminescence.     

Color improvement of white-light through Mn-enhancing yellow-green emission of SrSi2O2N2:Eu phosphor for white light emitting diodes

Photoluminescence (PL) enhancement of SrSi₂O₂N₂:Eu and the resultant color improvement of white-light were investigated via co-doping Mn with Eu. We observed that a unique absorption of host lattice of SrSi₂O₂N₂ and its visible band emission peaked at around ∼550 nm for SrSi₂O₂N₂:Mn²⁺ in the wavelength range of 450-600 nm. This highly eye-sensitive ∼550 nm-peaked band emission of SrSi₂O₂N₂ doped with Mn²⁺ happens to overlap the 535 nm-peaked band emission of SrSi₂O₂N₂ doped with Eu²⁺, resulting in an intensified photoluminescence in a maximum by 355%. By combining this as-prepared Mn intensified SrSi₂O₂N₂:Eu phosphor with blue InGaN chip, the quality of white-light was improved to 93.3% for color rendering index and 3584 K for correlated color temperature.     

Origin of PL intensity increase of CaMgSi2O6:Eu phosphor after baking process for PDPs application

We have synthesized blue-emitting CaMgSi₂O₆:Eu²⁺ (CMS) and evaluated its thermal stability after baking process. To evaluate its thermal stability, CMS was baked in air at 500 and 600 °C for 20 min, respectively, and compared with BaMgAl₁₀O₁₇:Eu²⁺ (BAM) treated in the same condition. After baking process, CMS showed somewhat increased photoluminescence (PL) intensity with baking temperature. To investigate the reasons behind the increase of PL intensity after baking process, vacuum ultraviolet (VUV)/PL, electron spin resonance (ESR), X-ray photoelectron spectroscopy (XPS) techniques were applied. From the ESR and the XPS analyses, it is noted that spectral intensity of Eu²⁺ ion somewhat increased. It was believed that due to charge balance Eu³⁺ ions reduced to Eu²⁺ ions during the baking process in air. It is clear that the concentration of Eu²⁺ increased after the baking process in air and it leads to slight increase of the VUV/PL intensity of CMS phosphor.     

Photoluminescence in MgxSr1−xAl2O4:Eu, Ndand electron-vibrational interaction in the Eu 5d states

Green phosphor compositions Mg_xSr_1−xAl₂O₄:Eu, Nd (with x=0.05-0.25) were prepared by solid state reaction method. The effect of Mg substitution on photoluminescence characteristics was investigated. The photoluminescence show intense green emission for MgSrAl₂O₄:Eu²⁺, Nd³⁺ with long persistence. This green emission corresponds to transitions from 4f⁶5d¹ to 4f⁷ of Eu²⁺ ion. Comparative analysis of the excitation and emission spectra were used to evaluate the crystal field splitting of the 5d states of Eu²⁺ and the parameters of electron-vibrational interaction, such as Huang-Rhys factor, effective phonon energy, and zero-phonon line position.     

Photoluminescence and phosphorescence properties of MAl2O4:Eu, Dy (M=Ca, Ba, Sr) phosphors prepared at an initiating combustion temperature of 500 °C

Eu²⁺ and Dy³⁺ co-doped calcium aluminate, barium aluminate and strontium aluminate phosphors were synthesized at an initiating combustion temperature of 500 °C using urea as an organic fuel. The crystallinity of the phosphors was investigated by using X-ray diffraction (XRD) and the morphology was determined by a scanning electron microscope (SEM). The low temperature monoclinic structure for both CaAl₂O₄ and SrAl₂O₄ and the hexagonal structure of BaAl₂O₄ were observed. The effect of the host materials on the photoluminescence (PL) and phosphorescence properties were investigated by using a He-Cd Laser and a Cary Eclipse fluorescence spectrophotometer, respectively. The broad band emission spectra observed at 449 nm for CaAl₂O₄:Eu²⁺, Dy³⁺, 450 nm (with a shoulder-peak at 500 nm) for BaAl₂O₄:Eu²⁺, Dy³⁺ and 528 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ are attributed to the 4f⁶5d¹ to 4f⁷ transition in the Eu²⁺ ion in the different hosts.     

Optical properties of (ZnO)0.5(P2O5)0.5 glasses doped with Gd2O3:Eu nanoparticles and Eu2O3

Binary (ZnO)_0.5(P₂O₅)_0.5 glasses doped with Eu₂O₃ and nanoparticles of Gd₂O₃:Eu were prepared by conventional melt-quench method and their luminescence properties were compared. Undoped (ZnO)_0.5(P₂O₅)_0.5 glass is characterized by a luminescent defect centre (similar to L-centre present in Na₂O-SiO₂ glasses) with emission around 324 nm and having an excited state lifetime of 18 ns. Such defect centres can transfer the energy to Eu³⁺ ions leading to improved Eu³⁺ luminescence from such glasses. Based on the decay curves corresponding to the ⁵D₀ level of Eu³⁺ ions in both Gd₂O₃:Eu nanoparticles incorporated as well as Eu₂O₃ incorporated glasses, a significant clustering of Eu³⁺ ions taking place with the latter sample is confirmed. From the lifetime studies of the excited state of L-centre emission from (ZnO)_0.5(P₂O₅)_0.5 glass doped with Gd₂O₃:Eu nanoparticles, it is established that there exists weak energy transfer from L-centres to Eu³⁺ ions. Poor energy transfer from the defect centres to Eu³⁺ ions in Gd₂O₃:Eu nanoparticles doped (ZnO)_0.5(P₂O₅)_0.5 glass has been attributed to effective shielding of Eu³⁺ ions from the luminescence centre by Gd-O-P type of linkages, leading to an increased distance between luminescent centre and Eu³⁺ ions.     

Luminescence of KCaSO4Cl:X, Y (X=Eu or Ce; Y=Dy or Mn) halosulfate material

Polycrystalline KCaSO₄Cl:Eu, Dy, KCaSO₄Cl:Ce, Dy and KCaSO₄Cl:Ce, Mn phosphors prepared by a solid state diffusion method have been studied for its photoluminescence (PL) characteristics. The presence of two overlapping bands at around 400 and 450 nm in the PL emission spectra of the phosphor suggests the presence of Eu²⁺ in the host compound occupying two different lattice sites. The effects of co-doping on the photoluminescence (PL) characteristics of KCaSO₄Cl:Eu or Ce phosphors have been studied. The decrease in peak intensity of the phosphor on co-doping it with Dy gives an insight into the emission mechanism of the phosphors, which involves energy transfer from Eu²⁺→Dy³⁺, Ce³⁺→Dy³⁺ and Ce³⁺→Mn²⁺.     

Synthesis of Y2Si2O7:Eu nanocrystal and its optical properties

Nanocrystalline Y₂Si₂O₇:Eu phosphor with an average size about 60 nm is easily prepared using silica aerogel as raw material under ultrasonic irradiation and annealing temperature at 300-600 °C and this nanocrystalline decomposes into Y₂O₃:Eu and silica by heat treatment at 700-900 °C. The excitation broad band centered at 283 and 254 nm results from Eu³⁺ substituting for Y³⁺ in Y₂Si₂O₇ and Y₂O₃/SiO₂, respectively. Compared with Y₂O₃:Eu/SiO₂ crystalline, the PL excitation and emission peaks of Y₂Si₂O₇:Eu nanocrystalline red-shift and lead to the enhance of its luminescence intensity due to the different chemical surroundings of Eu³⁺ in above nanocrystallines. The decrease of PL intensity may be ascribed to quenching effect resulting from more defects in Y₂O₃:Eu/SiO₂ crystalline.