Synthesis and electroluminescent properties of a carbozole-functionalized europium(III) complex

A novel europium(III) complex, tris(dibenzoylmethanate){1-[9-hexyl-9H-carbazole]-2-(2-pyridyl)-benzimidazole}europium(III) [Eu(DBM)₃(CAR-PyBM)] functionalized by a carbozole fragment, was synthesized and used as emitting material in organic electroluminescent (EL) devices. Compared with the device based on an unfunctional Eu(III) complex, [Eu(DBM)₃HPyBM] (HPyBM=2-(2-pyridyl)benzimidazole), the EL performances of the device using [Eu(DBM)₃(CAR-PyBM)] as an emitter was significantly enhanced due to the improvement of hole-transporting ability. The maximum efficiency and luminance of red emission achieved from the device with the configuration of ITO/N,N′-diphenyl-N,N′-bis(3-methylphenyl)-1,1′-biphenyl-4,4′diamine (TPD, 50 nm)/ [Eu(DBM)₃(CAR-PyBM)] (30 nm)/1,3,5-tirs-(N-phenylbenzimidazol-2-yl)benzene (TPBI, 20 nm)/LiF (1.5 nm)/Al were 4.2 cd/A and 200 cd/m², respectively.     

A terbium (III) complex with triphenylamine-functionalized ligand for organic electroluminescent device

A novel ligand, 4-diphenylamino-benzoic acid (HDPAB), and the corresponding Tb (III) complex, Tb (DPAB)₃ which can be dissolved easily in organic solvents were synthesized and characterized. Organic electroluminescent (EL) device with a structure of indium tin oxide (ITO)/poly(N-vinylcarbazole) (PVK): Tb (DPAB)₃ (50 wt%, 80 nm)/1,3,5-tris-(N-phenylbenzimidazol-2-yl)benzene (TPBI) (30 nm)/tri(8-hydroxyquinoline)aluminum (AlQ) (20 nm)/LiF (1 nm)/Al (150 nm) in which Tb (DPAB)₃ acted as an emitter were fabricated. The maximum luminance of 230 cd m⁻² at 20 V and the maximum efficiency of 0.62 cd A⁻¹ were obtained due to the introduction of hole-transporting group, representing the best result to date among Tb (III) carboxylate complexes based EL devices. These results indicate that modifications of rare earth complexes are a promising way to improve the properties of EL devices.     

Highly efficient greenish blue-emitting organic diodes based on pyrene derivatives

We report the synthesis of pyrene derivatives as the light emissive layer for highly efficient organic electroluminescence (EL) diodes. Multilayer devices were fabricated with pyrene derivatives (ITO/NPB (50 nm)/blue material (30 nm)/BCP (10 nm)/Alq₃ (30 nm)/LiF (1 nm)/Al). By using 1,1′-dipyrene (DP) and 1,4-dipyrenyl benzene (DPB), the devices produced the blue EL emissions with 1931 Commission International de L’Eclairage coordinates of (x=0.21, y=0.35) and (x=0.19, y=0.25), respectively. The device with DPB shows a maximum brightness of 42,445 cd/m² at 400 mA/cm² and the luminance efficiency of 8.57 cd/A and 5.18 lm/W at 20 mA/cm².     

NaCl/Ca/Al as an efficient cathode in organic light-emitting devices

An efficient cathode NaCl/Ca/Al used to improve the performance of organic light-emitting devices (OLEDs) was reported. Standard N,N′-bis(1-naphthyl)-N,N′-diphenyl-1,1′ biphenyl 4,4′-dimaine (NPB)/tris-(8-hydroxyquinoline) aluminum (Alq₃) devices with NaCl/Ca/Al cathode showed dramatically enhanced electroluminescent (EL) efficiency. A power efficiency of 4.6 lm/W was obtained for OLEDs with 2 nm of NaCl and 10 nm of Ca, which is much higher than 2.0 lm/W, 3.1 lm/W, 2.1 lm/W and 3.6 lm/W in devices using, respectively, the LiF (1 nm)/Al, LiF (1 nm)/Ca (10 nm)/Al, Ca (10 nm)/Al and NaCl (2 nm)/Al cathodes. The investigation of the electron injection in electron-only devices indicates that the utilization of the NaCl/Ca/Al cathode substantially enhances the electron injection current, which in case of OLEDs leads to the improvement of the brightness and efficiency.     

Structure and luminescence studies of tris(nitrato-O,O′)bis(2,2′-bipyridyl-N,N′)dysprosium(III) complex

The title compound, [Dy(NO₃)₃(bipy)₂], is isostructural with the La, Pr, Nd, Eu and Lu analogues where bipy=2, 2′-bipyridyl. The Dy complex was crystallized in orthorhombic with space group Pbcn. The Dy(III) ion was coordinated with the two bipy ligands and three nitrate anions giving a ten coordination number. Measurements of the molar conductance in ethanol and water solutions indicate that the complex is non-electrolyte. A comparative study of the emission of [Dy(NO₃)₃(bipy)₂] complex with those of the adduct mixture of bipy and Dy at a 1:1 ratio, has been investigated. In the solid state, photoluminescence (PL) spectrum of the complex had sharp emission bands corresponding to the ⁴F_9/2→⁶H_15/2 (476.5 and 482 nm), ⁴F_9/2→⁶H_13/2(572.6 and 573.8 nm), ⁴F_9/2→⁶H_11/2 (661.6 nm) and ⁴H_3/2→⁶H_15/2 (961.0 nm) transitions. The hypersensitive peak of the complex has the yellow emission stronger than the blue emission in the solid state as well as in the solution. The complex has a good thermal stability due to the role of π-π interactions stacking.     

Efficient bright white organic light-emitting diode based on non-doped ultrathin 5,6,11,12-tetraphenylnaphthacene layer

High-performance undoped white organic light-emitting diode (OLED) has been fabricated using an ultrathin yellow-emitting layer of 5,6,11,12-tetraphenylnaphthacene (rubrene) inserted at two sides of interface between two N,N′-bis-(1-naphthyl)-N,N′- biphenyl-1,1′-biphenyl-4,4′- diamine (NPB) layers as a hole transporting and blue emissive layer, respectively. The results showed that a maximum luminance of the device reached to as high as 21,500 cd/m² at 15 V. The power efficiencies of 2.5 and 1.6 lm/W at a luminance of 1000 and 10000 cd/m², respectively, were obtained. The peaks of electroluminescent (EL) spectra locate at 429 and 560 nm corresponding to the Commissions Internationale De L’Eclairage (CIE) coordinates of (0.32, 0.33), which is independent of bias voltage. The performance enhancement of the device may result from direct charge carrier trapping in rubrene. Energy transfer mechanism was also found in the EL process.     

Synthesis and photophysical properties of novel polymeric Eu(III) complex with bicoordination ligand

A novel complex of Eu(III) with bicoordination ligand: 4,4′-bis[2-(2′-pyridyl) benzimidazol-yl]-biphenyl (Bmbp) has been synthesized. The structure of the ligand was characterized by ¹H NMR, FT-IR and UV-vis; Eu(III) complex was characterized by FT-IR, UV-vis, elemental analysis, conductivity measurements and gel-permeation chromatography (GPC). The luminescence properties were investigated by UV-vis and fluorescence spectra. The experimental results show that the complex contain more than one Eu(III) ion, the emission at 614 nm from the ⁵D₀→⁷F₂ electronic dipole transition is large enhanced, and the complex is excellent energy transfer from ligand to Eu³⁺in the solid state. Thermal property measurement and analysis show that it has a good thermal stability.     

White organic electroluminescence from fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc doped with phosphorescent material

Efficient white electroluminescence has been obtained by using an electroluminescent layer comprising of a blue fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc [Zn(hpb)₂] doped with red phosphorescent bis (2-(2′-benzothienyl) pyridinato-N,C^3′)iridium(acetylacetonate) [Ir(btp)₂acac] molecules. The color coordinates of the white emission spectrum was controlled by optimizing the concentration of red dopant in the blue fluorescent emissive layer. Organic light-emitting diodes were fabricated in the configuration ITO/α-NPD/Zn(hpb)₂:0.01 wt%Ir(btp)₂acac/BCP/Alq₃/LiF/Al. The J-V-L characteristic of the device shows a turn on voltage of 5 V. The electroluminescence (EL) spectra of the device cover a wide range of visible region of the electromagnetic spectrum with three peaks around 450, 485 and 610 nm. A maximum white luminance of 3500 cd/m² with CIE coordinates of (x, y=0.34, 0.27) at 15 V has been achieved. The maximum current efficiency and power efficiency of the device was 5.2 cd/A and 1.43 lm/W respectively at 11.5 V.     

Direct observation of the D′ 2g(P2)-A′ Π(2u) system for Cl2 by laser induced fluorescence spectroscopy: Determination of the absolute position of the A′ state

In a discharged supersonic jet of Cl₂, transitions of the D′ 2_g(³P₂)-A′ ³Π(2_u) system for ³⁵Cl₂ were observed directly by laser induced fluorescence spectroscopy. By a discharge in Cl₂, the Cl₂ molecules were populated into the A′ state, which is a metastable and optically forbidden state, from the state. An ultraviolet laser radiation excites the molecules to the D′ ion-pair state. A set of Dunham parameters for the A′ state is determined from a global least-squares fitting for 59 vibronic bands with v″ = 0-7. In the fitting, the previously reported data, T(v) and B(v) for the v = 14 and 15 bands of the A′ state [T. Ishiwata, A. Ishiguro, K. Obi, J. Mol. Spectrosc. 147 (1991) 300-320], were included. Y₀₀ = 57295.723(5) cm⁻¹ of the D′ state [J.-H. Si, T. Ishiwata, K. Obi, J. Mol. Spectrosc. 147 (1991) 334-345] was also included in the global fitting in order to determine the absolute position of the A′ state. The determined parameters of the A′ state are Y₀₀ = 17171.506(14), Y₁₀ = 255.915(85), Y₂₀ = −4.465(70), Y₃₀ = −8.7(23) × 10⁻², Y₄₀ = 6.3(35) × 10⁻³, Y₅₀ = −4.9(26) × 10⁻⁴, Y₆₀ = 1.43(69) × 10⁻⁵, Y₀₁ = 0.16282(15), Y₁₁ = −2.363(68) × 10⁻³, Y₂₁ = −5.01(93) × 10⁻⁵, and Y₃₁ = −3.01(36) × 10⁻⁶ (in cm⁻¹ and one standard deviations of the fit in parentheses). The absolute position of the A′ state is determined with good accuracy.     

Degradation of organic light-emitting diodes based on different-ligand complexes of terbium (III) salicylate and 2-phenoxybenzoate

Degradation (D) of organic light-emitting diodes (OLEDs) based on new different-ligand complexes of terbium salicylate (Tb(Sal)₃(TPPO)₂) and 2-phenoxybenzoate (Tb(pobz)₃(TPPO)₂) with triphenyl phosphinoxide (TPPO) was studied. Initial reversible D is associated with charge carrier trap filling. A temperature increase, applied stress relief, and short-term irradiation with UV light lead to trapped charge carrier release and electroluminescence (EL) intensity recovery. During strong heating, irreversible D is observed after the recovery; this D requires in addition an electric field (EF). Intense UV light causes D without EF. The use of ac bias voltage eliminates reversible D, and sealing retards irreversible long-term D.     

An organic electroluminescent device made from a gadolinium complex

A gadolinium ternary complex, tris(1-phenyl-3-methyl-4-isobutyryl-5-pyrazolone) (phenanthroline) gadolinium [Gd(PMIP)₃(Phen)] was synthesized and used as a light emitting material in the organic electroluminescent (EL) devices. The triple layer device with a structure of indium tin oxide (ITO)/N,N′-diphenyl-N,N′-bis(3-methylphenyl)-1,1′-biphenyl-4,4′-diamine (TPD) (20 nm)/Gd(PMIP)₃(Phen) (80 nm)/2, 9-dimethyl-4, 7-diphenyl-1, 10-phenanthroline (bathocuproine or BCP) (20 nm)/Mg: Ag(200 nm)/Ag(100 nm) exhibited green emission peaking at 535 nm. A maximum luminance of 230 cd/m² at 17 V and a peak power efficiency of 0.02 lm/w at 9 V were obtained.     

A luminescent dinuclear Eu(III) complex based on 2,8-bis(4′,4′,4′,-trifluoro-1′,3′-dioxobutyl)-dibenzothiophene for light-emitting diodes

A dinuclear Eu (III) complex Eu₂(dbt)₃·4H₂O was synthesized, where H₂dbt was 2,8-bis(4′,4′,4′,-trifluoro-1′,3′-dioxobutyl)-dibenzothiophene. The complex emits the characteristic red luminescence of Eu³⁺ ion due to the ⁵D₀→⁷F_J(J=0-4) transitions under 395 nm-light excitation with a luminescent quantum efficiency of 17%. The complex is thermally stable up to 280 °C. It was found that the complex can be effectively excited by a 395 nm-emitting InGaN chip. Bright red light was obtained using the complex as light color-conversion material.     

Analysis of guanosine-5′-monophosphate at nM level based on the co-luminescence effect of Tb-Gd-GMP system

This paper first found the co-luminescence effect of guanosine-5′-monophosphate (GMP) system. Experiment showed that La³⁺, Gd³⁺, Sc³⁺ and Y³⁺ all could enhance the luminescence of Tb-GMP system, among which Gd³⁺ has the greatest enhancement. Under the optimum conditions, the enhanced intensity of the system is in proportion to the concentration of GMP in the range from 3×10⁻⁸ to 3×10⁻⁵ mol/l. The detection limit is 3.9×10⁻⁹ mol/l. In the study of mechanism, we propose that both Tb and Gd complexes can form bigger netlike compound by the link of the oxygen bridge, through which the energy absorbed by Gd complex may transfer to Tb³⁺ in Tb complex.     

Efficient red organic light-emitting diode sensitized by a phosphorescent Ir compound

The efficiencies of red organic light-emitting diode (OLED) using tris-(8-hydroxy-quinoline)aluminum (Alq₃) as host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) as dopant were greatly increased by adding a small amount (0.3 wt%) of Ir compound, iridium(III) bis(3-(2-benzothiazolyl)-7-(diethylamino)-2H-1-benzopyran-2-onato-N′,C⁴) (acetyl acetonate) (Ir(C6)₂(acac)), as a sensitizer. The device has a sandwiched structure of indium tin oxide (ITO)/4,4′,4″-tris(N-(2-naphthyl)-N-phenyl-amino)triphenylamine (T-NATA) (40 nm)/N,N′-bis(1-naphthyl)-N,N′-diphenyl-1,1′-biphenyl-4,4′ diamine (NPB) (40 nm)/Alq₃:DCJTB (0.7 wt%):Ir(C6)₂(acac) (0.3 wt%) (40 nm)/Alq₃ (40 nm)/LiF (1 nm)/Al (120 nm). It can be seen that the current efficiencies of this device remained almost (13.8±1) cd/A from 0.1 to 20,000 cd/m² and the Commission International d’Eclairage (CIE) coordinates at (0.60, 0.37) in the range of wide brightness. The significant improvement was attributed to the sensitization effect of the doped Ir(C6)₂(acac), thus the energy of singlet and triplet excitons is simultaneously transferred to the DCJTB.     

Improved performance and stability by an Al/Ni bilayer cathode in organic light-emitting diodes

Al/Ni bilayer cathode was used to improve the electroluminescent (EL) efficiency and stability in N,N′-bis(1-naphthyl)-N,N′-diphenyl-1,1′ biphenyl 4,4′-dimaine (NPB)/tris-(8-hydroxyquinoline) aluminum (Alq₃)-based organic light-emitting diodes. The device with LiF/Al/Ni cathode achieved a maximum power efficiency of 2.8 lm/W at current density of 1.2 mA/cm², which is 1.4 times the efficiency of device with the state-of-the-art LiF/Al cathode. Importantly, the device stability was significantly enhanced due to the utilization of LiF/Al/Ni cathode. The lifetime at 30% decay in luminance for LiF/Al/Ni cathode was extrapolated to 400 h at an initial luminance of 100 cd/m², which is 10 times better than the LiF/Al cathode.     

Exciplex or electroplex emissions from the interface between aromatic diamine and 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline?

Organic light-emitting diodes (OLEDs) have been fabricated which consist of N,N′-diphenyl-N,N′-bis(3-methylphenyl)-1,1′-biphenyl-4,4′-diamine) (TPD), 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP), and tris(8-hydroxyquinoline) aluminum (Alq₃). Four emission peaks located at about 401 nm, 425 nm, 452 nm and 480 nm have been obtained in the electroluminescence (EL) spectra of these devices. The former two emissions originate from the exciton emission of TPD molecular. The last two emissions could be attributed to local (LOC) exiplex emission and charge transfer (CT) exiplex emission at the interface between TPD and BCP layers, respectively.     

Red electroluminescent process excited by hot holes in SrGa2S4:Ce, Mn thin film

This paper reports the first observation of red electroluminescence (EL) in SrGa₂S₄:Ce, Mn thin film. The EL spectrum consists of single broad emission band having a peak wavelength of 665 nm. The dominant EL decay time was 31 μs. The relationship between the applied voltage and the EL waveform was measured in single insulating thin film electroluminescent (TFEL) devices. An asymmetric EL waveform was observed in SrGa₂S₄:Ce, Mn TFEL devices under a rectangular applied voltage. The polarity of the EL waveform in these devices was different from the waveform in manganese-activated zinc sulfide ZnS:Mn devices. This indicates that hot holes excite the Mn²⁺ ions to cause the red EL.     

Photoluminescence and electroluminescence of a novel green-yellow emitting material-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl]-pyrazine-2,3-dicarbonitrile

A new compound with intramolecular charge transfer (ICT) property—5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl]-pyrazine-2,3-dicarbonitrile(BNPPDC) was synthesized. The new compound was strongly fluorescent in non-polar and moderately polar solvents, as well as in thin solid film. The absorption and emission maxima shifted to longer wavelength with increasing solvent polarity. The fluorescence quantum yield also increased with increasing solvent polarity from non-polar to moderately polar solvents, then decreased with further increase of solvent polarity. This indicates both “positive” and “negative” solvatokinetic effects co-existed. Using this material as hole-transporting emitter and host emitter, we fabricated two electroluminescent (EL) devices with structures of A (ITO/BNPPDC (45 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm) and B (ITO/N,N′-diphenyl-N,N′-bis-(3-methylphenyl) (1,1′-diphenyl)4,4′-diamine (TPD) (50 nm)/BNPPDC (20 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm). The devices showed green-yellow EL emission with good efficiency and high brightness. For example, the device A exhibited a high brightness of 17400 cd/m² at a driving voltage of 11 V and a very low turn-on voltage (2.9 V), as well as a maximum luminous efficiency 3.61 cd/A. The device B showed a similar performance with a high brightness of 12650 cd/m² at a driving voltage of 13 V and a maximum luminous efficiency 3.62 cd/A. In addition, the EL devices using BNPPDC as a host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) as a dopant (configuration: ITO/TPD (60 nm)/BNPPDC:DCJTB (2%) (30 nm)/TPBI (35 nm)/Mg:Ag (200 nm)) showed a good performance with a brightness of 150 cd/m² at 4.5 V, a maximum brightness of 12600 cd/m² at 11.5 V, and a maximum luminous efficiency of 3.30 cd/A.     

Multiple roles of bathocuproine employed as a buffer-layer in organic light-emitting diodes

Efficiency and brightness and carriers injection have been obviously improved by using bathocuproine (BCP) as a buffer-layer in organic light-emitting diodes. Compared with the bufferless device, the quantum efficiency of device ITO/NPB (10 nm)/Alq₃ (10 nm)/BCP (2.4 nm)/Al has increased four times at the same current density (32 mA/cm²). Moreover, the buffer layer has changed the current-voltage properties and the turn-on voltage has obviously decreased. Considering BCP and Al³⁺ can react conveniently under room temperature, we suggest that a complex cathode structure of BCP/[(Al)_x(BCP)_y]^3x+/Al has formed under electric field and the new cation [(Al)_x(BCP)_y]^3x+ at the BCP/Al interface has improved the internal electric field and then enhanced the electrons injection. we conclude that: for a very thin (<1 nm) BCP buffer layer, improving electron injection will principally responsible to the improvement of the performance of the OLEDs; for a thicker BCP layer, there will be a synthetic function of BCP: improving electron injection, hole-blocking and electron-transporting.     

Improved performance of organic light-emitting devices with plasma treated ITO surface and plasma polymerized methyl methacrylate buffer layer

Transparent indium-tin-oxide (ITO) anode surface was modified using O₃ plasma and organic ultra-thin buffer layers were deposited on the ITO surface using 13.56 MHz rf plasma polymerization technique. A plasma polymerized methyl methacrylate (ppMMA) ultra-thin buffer layer was deposited between the ITO anode and hole transporting layer (HTL). The plasma polymerization of the buffer layer was carried out at a homemade capacitively coupled plasma (CCP) equipment. N,N′-Diphenyl-N,N′-bis(3-methylphenyl)-1,1′-diphenyl-4,4′-diamine (TPD) as HTL, Tris(8-hydroxy-quinolinato)aluminum (Alq₃) as both emitting layer (EML)/electron transporting layer (ETL), and aluminum layer as cathode were deposited using thermal evaporation technique. Electroluminescence (EL) efficiency, operating voltage and stability of the organic light-emitting devices (OLEDs) were investigated in order to study the effect of the plasma surface treatment of the ITO anode and role of plasma polymerized methyl methacrylate as an organic ultra-thin buffer layer.