Liquid chromatographic isolation of coplanar PCB congeners on an activated carbon stationary phase

A rapid and uncomplicated method for the fractionation of PCBs leading to an isolation of the highly toxic non-ortho substituted PCBs is described. The liquid chromatographic separation was achieved on a stationary phase consisting of activated carbon and Celite 545. Using eluents with different polarity, isolation of the non-ortho substituted PCBs in a single fraction was achieved. The fractions were analysed by GC/MS. The method was tested by the determination of non-ortho substituted PCBs in technical mixtures (Aroclor 1254 and Aroclor 1242). The results were compared with those obtained by using an HPLC fractionation on a porous graphitic carbon column. Finally, the micro-column fractionation was used for the determination of non-ortho substituted PCBs in native soil samples.     

Isolation and determination of toxic congeners of polychlorinated biphenyls in environmental samples

A Method has been developed for the separation and enrichemen of there non-ortho, eight mono-ortho, and di-ortho substituted polychlorinated biphenyls (PCBs) from Aroclor formulations and environmental samples. The fractionation is accomplished using high performance liquid chromatography (HPLC) with a 2-(1-pyrenyl)ethyldimethylsilysily silca column. GC-MSD with an optimized temperature program was used for quantitation, Hexane, pentane, cyclohexane, iso-octane, and 2-propanol were tested as a mobile phase for the isolation of the thirteen target PCBs in a Aroclor 1242, 1254, and 1260 (1:1:1) misture, Pentane at room temperature with a slow rate of 0.7 ml/min is the condition of choice. The average recovery of thirteen target PCBs spiked in the Aroclor mixture is 99.5% with an average relative standard deviation of 4.5%. The average method detection limit is 8pg/μl. Targer PCBs in the reference solis, incinarator ash, and sediment samples were measured.     

Congener-specific method for the determination of ortho and non-ortho polychlorinated biphenyls, polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans in foods by carbon-column fractionation and gas chromatography-isotope dilution mass spectrometry

 The chromatographic behavior of ortho and non-ortho polychlorinated biphenyls (PCBs) on supported carbon columns has been investigated and the structure-affinity relationship of activated carbon towards PCB molecules established. Optimisation of the parameters controlling the elution of PCB congeners through the carbon column led to the development of a solvent scheme for the efficient separation of (i) ortho substituted PCBs, (ii) non-ortho substituted PCBs and (iii) polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in three separate fractions. A method for the extraction, clean-up, fractionation and determination of ortho and non-ortho substituted PCBs by GC-isotope dilution MS was developed and validated by analysis of a certified reference material. Possible losses of PCBs during freeze-drying and interferences of aliphatic hydrocarbons during mass spectrometric determination of ortho substituted PCBs are also discussed. Received: 23 June 1995/Revised: 9 May 1996/Accepted: 25 May 1996     

Development of a high-performance liquid chromatography carbon column based method for the fractionation of dioxin-like polychlorinated biphenyls

A method to separate polychlorinated biphenyls (PCBs) by using high-performance liquid chromatography (HPLC) was developed. The HPLC column was packed with Amoco PX-21 activated carbon dispersed on octadecylsilane (ODS). The separation was carried out by gradient elution with n-hexane-dichloromethane and toluene in the forward direction followed by reversed elution with toluene. The results show that this HPLC method is useful for the separation of PCBs according to the number of substituted ortho chlorine atoms attached to the biphenyl structure. Average recoveries for a number of individual di-ortho PCBs, mono-ortho PCBs, and non-ortho PCBs in three selected elution windows were 97, 92, and 96%, respectively. Clophen A50, a herring sample, and a cod liver oil sample were fractionated on the column and the analytical results are compared with data from the literature. The method presented here is useful for quantitative separations of mono-ortho PCBs as well as non-ortho PCBs which have been assigned toxic equivalency factors by the World Health Organisation.     

Determination of polychlorinated biphenyls in human blood plasma by on-line and off-line liquid chromatography–gas chromatography

A method for the determination of non-, mono- and di-ortho substituted polychlorinated biphenyls in human blood plasma is presented. The non-ortho CBs are isolated from the bulk of PCBs by HPLC on a dinitroanilino-propyl silica column and collected as a heart-cut fraction that is transferred on-line to GC-MS utilizing concurrent solvent evaporation technique. The on-line coupling serves to lower the limit of determination and to partly automate the sample clean-up. The di- and mono-ortho CBs are analyzed by off-line GC-ECD using two different columns. Sample pre-treatment is performed by extraction with organic solvents and fractionation on silica gel. A high reproducibility and an absolute over-all recovery of approximately 70 % is demonstrated. The method is applied to samples of blood from 5 individuals. All the samples demonstrated a similar relative concentration profile. It was also shown that three CB congeners (CB 126, CB 156 and CB 170) contributed to the major part of the toxic equivalent quantity of the PCB content in the blood.     

Separation of polychlorinated dibenzo-p-dioxins/furans,non-ortho/mono/di/tri/tetra-ortho-polychlorinated biphenyls,and polybrominated diphenyl ethers groups of compounds prior to their determination with large volume injection gas chromatography—Quadrupole ion storage tandem mass spectrometry

Polychlorinated dibenzo-p-dioxins/furans (PCDD/Fs), polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) are important environmental contaminants. Their maximum legally allowable levels in food and environment are in the low pg g⁻¹ range. Therefore some highly selective and sensitive analytical methods must be used to determine them. Prior to final determination by GC/MS the cleaned-up samples have to be split into some fractions in view of large differences in concentrations of various analytes and existence of numerous chromatographic co-elutions (which in any case cannot be fully avoided). The aim of this study was to: (i) develop a robust, time-saving analytical method to isolate, clean-up and fractionate PCBs, PBDEs and PCDD/Fs prior to their determination with gas chromatography/ion trap mass spectrometry; (ii) assess method performance using laboratory validation data and some certified reference materials; (iii) use the developed method to assess PCB/PBDE/PCDD/F levels in samples of commercially available food. A combination of alumina, florisil, modified silica gel and two carbon columns were used for sample cleanup and fractionation. Separate fractions containing dioxins/furans, PBDE, non-ortho, mono-ortho and di-/tri-/tetra-ortho PCBs were obtained. The method statistical parameters were compatible with 1883/2006 EC Regulation (80–120%, RSD below 15%). The method performance was successfully used to evaluation of some real life food samples.     

Method for the determination of three toxic non-ortho chlorine substituted coplanar PCBs in environmental samples at part-per-trillion levels

A method has been devised combining alkali digestion, carbon chromatography and high-resolution gas chromatography for the determination of 3,3',4,4'-tetra, 3,3',4,4',5-penta, and 3,3',4,4',5,5'-hexachlorobiphenyl, the biologically active congeners of PCBs and approximate isostereomers of 2,3,7,8-TCDD. This method permits determinations of parts-per-trillion levels of these toxic residues in biological samples. Interference both from biogenic and from xenobiotic substances was reduced to extremely low levels. Using this method, 13.5 ng of 3,3'4,4'-tetrachlorobiphenyl/g, 0.89 ng of 3,3'4,4',5-pentachlorobiphenyl/g and 0.64 ng of 3,3',4,4'5,5'-hexachlorobiphenyl/g were detected on wet weight basis in the blubber of a finless porpoise. To our knowledge this is the first report on the three toxic non-ortho chlorine substituted PCB residues detected in a higher mammal in the wilderness.     

Ratios of PCB 138, PCB 163, and PCB 164 in aroclor mixtures

The gas chromatographic separation of PCB 138, PCB 163, and PCB 164 in Aroclor mixtures can be achieved by application of a CP-Select for PCBs stationary phase. In technical PCB mixtures with a degree of chlorination exceeding 40% (Aroclor 1242, 1254, 1260, and 1262) these three hexa-chlorobiphenyls were present. The highest concentrations of the PCBs under investigation were found in Aroclor 1260. The ratio PCB 163: PCB 138 increased with an increasing degree of chlorination of technical PCB mixtures.     

Comparison of two extraction methods for determination of PCBs and PCTs in mussels from Galicia

We compared two extraction methods for use in GC-ECD determination of polychlorinated bi- and terphenyl contaminants (PCBs and PCTs respectively) in mussels (Mytilus galloprovincialis). Mussels spiked with standard PCB and PCT mixtures Aroclor 1260 and Aroclor 5460 were extracted with cold acetonitrile, or with 1:1 n-hexane/ dichloromethane in a Soxhlet extractor, which gave the better mean recoveries of 99.0 +/- 2.5% and 59.5 +/- 8.3% for PCBs and PCTs respectively.     

Application of a novel large-volume injection method using a stomach-shaped inlet liner in capillary gas chromatographic trace analysis of dioxins in human milk and plasma.

A newly developed large-volume injection (LVI) technique that employs a unique stomach-shaped inlet liner (SSIL) inside of a programmable temperature vaporizer was used for the determination of trace amounts of dioxins in human milk and plasma. The initial temperature and the initial dwelling time of the inlet and the kind of solvent used were found to be critical in determining the analytical sensitivity of dioxins due to the loss of these relatively volatile compounds during solvent vaporization. Human milk and plasma were purified and fractionated by pre-packed multi-layered silica-gel chromatography and activated carbon silica-gel column chromatography. A 20-microL aliquot of the fraction collected from the chromatography with toluene was directly applied to the LVI system in high-resolution gas chromatography/high-resolution mass spectrometry. Excellent correlation (r > 0.97) between the values obtained by the LVI method using the SSIL device and those by the conventional regular-volume splitless injection method was obtained for PCDDs, PCDFs and non-ortho PCBs in human milk and plasma samples.     

Polychlorinated biphenyls,dibenzo-p-dioxins and dibenzofurans in soil samples from airport areas of Croatia

Levels and patterns of polychlorinated biphenyls (PCBs) were studied in surface soil samples collected in the coastal part of Croatia within and surrounding four different airports and in the vicinity of two partially devastated electrical transformer stations. The compounds accumulated from air-dried soil samples by multiple ultrasonic extraction with an n-hexane?:?acetone 1?:?1 mixture were analysed by capillary gas chromatography with electron capture and ion-trap detection. PCBs were quantified against a standard Aroclor 1242/Aroclor 1260 mixture and a standard mixture of 17 individual PCB congeners (IUPAC No.: 28, 52, 60, 74, 101, 105, 114, 118, 123, 138, 153, 156, 157, 167, 170, 180, and 189). The mass fractions of total PCBs in 18 soil samples collected within the airport premises ranged from 3 to 41?327?µg/kg dry weight (dw) (median: 533?µg/kg?dw), and those in 21 samples collected at a distance ranging from several metres to 5?km away from the airport fence, from <1 to 39?µg/kg?dw (median: 5?µg/kg?dw). The highest PCB levels were determined in soils along the airport aprons where the aircrafts were serviced and refuelled. The PCB pattern was very similar to technical Aroclor 1260 in all airport soils. The PCB pattern in 22 soils collected in the vicinity of electrical transformer stations was dominated by congeners contained in Aroclor 1242. These soils contained 7 to >400?µg/kg?dw of total PCBs. One highly PCB-contaminated airport soil sample was analysed for polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). With an international toxic equivalent (I-TEQ) of 9.7?ng/kg?dw, the airport soil contamination was within values typical for urban and rural areas, and the congener patterns gave no clear indication for PCBs as the only source of PCDDs/PCDFs.     

Evaluation of automated direct sample introduction with comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry for the screening analysis of dioxins in fish oil

An automated direct sample introduction technique coupled to comprehensive two-dimensional gas chromatography-time of flight mass spectrometry (DSI-GC x GC/TOF-MS) was applied for the development of a relatively fast and easy analytical screening method for 17 polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) and 4 non-ortho polychlorinated biphenyls (PCBs) in fish oil. Comparison of instrumental performance between DSI-GC x GC/TOF-MS and the traditional gas chromatographic high resolution mass spectrometric (GC-HRMS) method showed good agreement of results for standard solutions analyzed in blind fashion. Relatively high tolerance of the DSI technique for lipids in the final extracts enabled a streamlined sample preparation procedure that only required gel permeation chromatography (GPC) and solid-phase extraction (SPE) cleanup with graphitized carbon black. The sample size for the method was 2g of cod liver oil, which achieved limits of quantitation (LOQs) of 0.019-7.8 pg/g toxic equivalent quotients for the individual PCDD/Fs. Lower detection limits can be achieved by using larger sample size and scaling up the sample preparation procedure, but this adds to the labor, time, solvent consumption, and expense of the approach. However, the streamlined method yielded 0.94 pg/g and 2.3 pg/g LOQs for 2,3,7,8-tetrachloro dibenzofuran (TCDF) and 3,3',4,4',5-pentachloro biphenyl (CB126), which were sufficiently low for regulatory monitoring of 2g samples. Therefore, instead of congener specific analysis, this streamlined analytical screening method for TCDF and CB126 has the potential to monitor fish oil contaminated with dioxin and dioxin-like PCBs at or above current food safety limits. Acceptable recoveries for nearly all analytes at three different spiking levels in fish oil samples were achieved with good repeatability.     

Potentiometric stripping determination of heavy metals using a graphite-reinforcement carbon vibrating electrode

Potentiometric stripping determination of Cd, Cu and Zn using a vibrating electrode (VE) is presented. A simple VE was constructed by using a piezoelectric bimorph oscillator and an inexpensive graphite-reinforcement carbon (GRC) rod (a mechanical pencil). Experimental results obtained with the simple VE follow the equation valid for quantitative application of potentiometric stripping analysis (PSA) in large solutions. It was found that the GRC vibrating electrode is suitable for multielement trace analysis of small samples of 0.05 mL. The relative standard deviations for divalent metals are better than 2%. Received: 3 February 1997 / Revised: 2 June 1997 / Accepted: 7 June 1997     

Fractionation of chlorinated and brominated persistent organic pollutants in several food samples by pyrenyl-silica liquid chromatography prior to GC-MS determination

A high-performance liquid chromatography (HPLC) method using a column of 2-(1-pyrenyl) ethyldimethylsilylated silica was developed in this work in order to achieve satisfactory and reproducible fractionation of polychlorinated biphenyls (PCBs) from brominated flame retardants (BFRs) (polybrominated diphenylethers, PBDEs; and polybrominated biphenyls, PBBs). After the study of different chromatographic parameters (mobile phase composition and separation temperature were the most important) an isocratic elution with isooctane:toluene (98:2, v/v) at a flow-rate of 1 mL/min, a temperature of 45 °C, and UV-detection at 225 nm was selected for fractionation of PCBs (time region, 4.0-5.8 min) from PBDEs (5.8-9.0 min) and from PBBs (5.8-11.0 min). The applicability of this method to food samples was demonstrated by fractionating PCBs from PBDEs in three food samples (cheese, milk, and fish). Interferences from PCBs (present in real samples at much higher concentrations than PBDEs) were removed in this way. In addition, by analysing these samples by gas chromatography-mass spectrometry (GC-MS) with and without previous fractionation we were able to observe an improvement in detection sensitivity for PBDEs after HPLC fractionation.     

Quantitative determination of toxic mono- and non-ortho polychlorinated biphenyls in cod liver oil after selective liquid chromatographic separation

Summary By application of chromatographic column filled with Supelclean ENVI-Carb/Celite and elution with three solvents of different polarity three PCB fractions were obtained. Fraction A contained poly-ortho PCBs, Fraction B mono-ortho PCBs, and Fraction C non-ortho PCBs. The Supelclean ENVI-Carb/Celite column was used in combination with a sample preparation procedure for pre-cleaning of acid-stable chlorinated hydrocarbons such as DDT and its metabolites, HCH isomers, and regulation-relevant PCB congeners. The method was optimized using standard solutions of 55 PCB congeners, 8 chlorinated pesticides and contaminated cod liver oil samples. The influence of traces of remaining matrix on the elution profile of the organochlorine compounds on Supelclean ENVI-Carb/Celite was observed. Quantitation was carried out by GC-ECD with fused silica capillary columns of different polarity.     

Temperature effect on HPLC retention of PCBs on porous graphitic carbon

Summary The effect of column temperature on solute retention was investigated for 10 PCBs with different degrees of planarity (degree of ortho position substitution). The variation of retention values (lnk) with temperature was measured using two solvents, n-hexane and dichloromethane, as mobile phase: retention decreases as temperature increases. The relationship between lnk values and temperature (1/T) exhibits a good linearity. The ΔH ⁰ values calculated are in the −2 to −5 kcal mole^{− 1} range: they are very similar for compounds with the same degree of ortho-substitution and are significantly higher for non-ortho substituted congeners. High temperature significantly improves separation efficiency (plate number significantly increases): this effect is the dominant factor controlling chromatographic resolution, which improves with increasing temperature. Operating at 40 °C, an efficient separation of planar PCBs was obtained with low solvent consumption.     

Determination of 26 polychlorinated biphenyls congeners in soil samples using microwave-assisted extraction with open vessel and gas chromatography

A procedure focused on microwave-assisted extraction in open vessel (MAE-OV) and gas chromatography with electron capture detection (GC-ECD) was used for the determination of 26 congeners of polychlorinated biphenyls (PCBs) in soil samples. The limit of detection (LOD) and limit of quantification (LOQ) were evaluated for commercial PCBs mixture Aroclor1260. LOD and LOQ were calculated for each PCB congener, in the ranges (0.03–0.27?ng?g^?1) and (0.11–0.70?ng?g^?1), respectively. After optimization, 26 PCBs congeners were successfully extracted from soil samples with recovery amounts ranging between 84.7% and 117.3% for all PCBs congeners. The evaluated method of MAE-OV showed good separation and extraction of all PCBs congeners from soil samples. Extraction parameters such as solvent choice, power and extraction time were investigated. This study indicated that MAE-OV could be an interesting alternative method to extract PCBs from soils, since it is economical, easy, fast and requires low amounts of solvents.     

Optimization and application of high-resolution gas chromatography with ion trap tandem mass spectrometry to the determination of polychlorinated biphenyls in atmospheric aerosols

Optimization of the Finnigan GCQ ion trap mass spectrometry (ITMS) system and a clean-up procedure were carried out in order to apply high-resolution gas chromatography-tandem mass spectrometry for the analysis of polychlorinated biphenyls (PCBs) in aerosols. Six ITMS operating parameters, including isolation time, excitation voltage, excitation time, "q" value, ion source temperature and electron energy were adjusted in order to optimize the instrument analytical performance. The adjustment of all parameters substantially increased the sensitivity of ITMS in the MS-MS mode. Changes in isolation time did not particularly affect ITMS sensitivity while ion source temperature had the strongest influence. After optimization, a limit of detection of 600 fg/microl with S/N varying from 8 up to 91 was achieved. The application of the optimized ITMS parameters conjointly with the developed clean-up procedure resulted in method detection limits of 10-20 fg/m3 for the determination of PCBs, in the particulate and gas phase of the atmospheric aerosol of background areas in the Eastern Mediterranean and Sweden.     

Method development for the analysis of polybrominated diphenyl ethers, polychlorinated biphenyls, polychlorinated dibenzo-p-dioxins and dibenzo-furans in single extract of sediment samples

A comprehensive method was developed for quantitative analysis of polybrominated diphenyl ethers (PBDEs), polychlorinated biphenyls (PCBs) and polychlorinated dibenzo-p-dioxins and dibenzo-furans (PCDD/Fs) in one single extract of environmental samples. The sample preparation procedure included two fractionation steps using silver nitrate silica chromatography to separate PBDEs from PCBs and PCDD/Fs and florisil column to separate PCBs from PCDD/Fs. Acidic silica, acidic alumina and gel permeation chromatography (GPC, for PCBs) or activated carbon column (for PCDD/Fs) were used for further clean-up. The sample extracts were analyzed by using high-resolution gas chromatography/high-resolution mass spectrometry. The entire method was validated from the analysis of mixed standards of PBDEs, PCBs and PCDD/Fs (n = 3); the analysis of certified reference biota (WMF-01). The method was applied for the analysis of 10 sediment samples collected from Haihe River and Dagu Drainage River in Tianjin City. No significant PBDEs pollution was found in the areas.     

分散固相萃取-气相色谱-质谱法测定茶叶中18种多氯联苯

建立了以羧基化多壁碳纳米管（MWCNTs-COOH）和N-丙基乙二胺（PSA）为分散固相萃取吸附剂的前处理净化技术,结合气相色谱-质谱（GC-MS）同时检测茶叶中18种多氯联苯（PCBs）的方法。茶叶样品经正己烷-丙酮（1：1,v/v）超声提取后,通过甲苯溶剂置换,以MWCNTs-COOH和PSA混合吸附剂净化,采用电子轰击离子源、选择离子监测模式测定,以保留时间和特征离子丰度比定性,基质匹配标准溶液外标法定量。考察了提取溶剂及吸附剂种类和用量、提取时间和净化时间对分析结果的影响,优化了气相色谱-质谱条件,并评估了优化实验条件下的方法性能。在最优实验条件下,18种PCBs在5~500 μg/kg范围内线性关系良好,相关系数（r）不低于0.9998;当加标水平为5、10和100 μg/kg时,3种茶叶基质中18种PCBs的平均回收率为90.7%~115.2%,相对标准偏差（n=5）为0.3%~10.9%;方法的检出限为0.3~1.7 μg/kg,定量限均为5 μg/kg。该方法操作简单、快速,准确可靠、灵敏度高,样品净化效果好,可用于不同种类茶叶基质中18种PCBs的测定。