自动顶空衍生化固相微萃取法测定啤酒中的老化醛类化合物

采用邻-五氟苯甲基羟胺(PFBOA)衍生,顶空固相微萃取(HS-SPME)和气相色谱质谱(GC-MS)测定啤酒中2-甲基丁醛、3-甲基丁醛、反-2-壬烯醛等8种老化醛类化合物.顶空固相微萃取采用65 μm PDMS/DVB纤维,先用纤维吸附PFBOA溶液,再将纤维插入装有2 mL啤酒的20 mL顶空进样瓶的顶空中在60 ℃萃取60 min,衍生和萃取都在自动进样器中进行.采用GC-MS检测,特征离子为m/z 181.8种羰基化合物在0.2～500 μg/L范围内线性关系良好,相关系数在0.990以上.检测样品的相对标准偏差为1.0%～15.7%,回收率为88%～103%.同时研究并讨论了萃取纤维、萃取温度、萃取时间、样品体积等因素对醛类萃取量的影响.该方法可用于啤酒保鲜期研究和产品质量控制.     

原位乙酰化-顶空固相微萃取测定水中酚类化合物

建立了原位乙酰化-顶空固相微萃取-气相色谱/质谱联用测定水中酚类及氯酚类化合物的方法,考察了对衍生化以及萃取过程有影响的相关因素.结果表明,采用65 μm PDMS/DVB涂层纤维效果最好.在10 mL样品中,搅拌速率600 r/min、100 μL乙酸酐、0.10 g Na2HPO4、4.0 g NaCl、60 ℃时各被测组分检出限在0 014～0 044 μg/L之间,相对标准偏差(RSD)≤13.7%,在考察的浓度范围(0.02～25 μg/L)内均呈线性变化.实际废水样品测定结果表明,相对标准偏差(9.24%)和回收率(86.4%)符合环境水体中痕量酚类化合物监测的质控要求.     

酱油中3-氯-1,2-丙二醇检测能力验证

为了解国内实验室在3-氯-1,2一丙二醇检测领域的能力,中国国家认证认可监督管理委员会(CNCA)组织了酱油中3一氯一1,2-丙二醇检测能力验证活动,有19个省、市、自治区的34个实验室参加.测试结果满意的实验室占73.5%.     

固相萃取-气相色谱-质谱法测定酱油中3-氯-1,2-丙二醇

建立了酱油中3-氯-1,2-丙二醇(3-MCPD)残留量的同相萃取-气相色谱-质谱(GC/MS)分析方法.利用SampliQ OPT固相萃取柱净化样品,考察了乙醇、丙酮、乙醚、乙醚-正已烷(9:1,V/V)4种洗脱液对3-MCPD回收效果的影响.洗脱液在室温下经氮气吹干后用双(三甲基硅烷基)三氟乙酰胺-三甲基氯硅烷(B...     

顶空固相微萃取-气相色谱-质谱法快速测定酱油中的挥发性风味成分

建立了一种快速简便地测定酱油中挥发性风味成分的顶空固相微萃取（HS-SPME）-气相色谱-质谱法(GC-MS)。以2-辛醇为内标,考察了萃取头、萃取时间、离子强度、萃取温度对酱油样品中挥发性风味物质萃取的影响。该方法对酱油中常见挥发性风味成分的测定有良好的重复性和回收率,对常见挥发性物质的定量比较准确。优化的HS-SPME条件为：涂层厚度为85 μm聚丙烯酸酯(PA)萃取纤维头,于45 ℃、NaCl质量浓度为250 g/L下对酱油样品顶空吸附40 min,于250 ℃下解吸2 min后进行GC-MS分离鉴定。酱油样品的分析结果表明,其挥发性风味物质中含量较高的是醇、酸、酯和酚类,此外还有一些羰基化合物和杂环化合物。     

顶空固相微萃取-气相色谱法测定饮用水中氯酚

提出了应用气相色谱法与顶空固相微萃取样品预处理技术相结合的方法测定饮用水中2,4,6-三氯酚(TCP)和五氯酚(PCP)。选用20mL顶空瓶,其中预置0.1mol·L~(-1)盐酸溶液0.5mL及氯化钠4.0g,加入水样10.0mL,立即封盖。插入85μm聚丙烯酸酯萃取头,在500r·min~(-1)转速振荡条件下于60℃萃取40 min,随之进入色谱仪解吸并测定。测定中采用HP-5毛细管柱和程序升温(40℃～280℃)条件,并用载气流量为3mL·min~(-1)。测得2,4,6-TCP及PCP的线性范围依次为55μg·L~(-1)和12μg·L~(-1)以内,其检出限(3S/N)依次为0.15μg·L~(-1)和0.13μg·L~(-1),加入3个浓度水平的标准溶液对方法的回收率及精密度作了试验,测得回收率在90.0%～112.8%之间,相对标准偏差(n=6)在3.0%～4.9%之间。     

固相萃取-气相色谱/负化学电离-质谱法测定酸水解植物蛋白及酱油中的3-氯-1,2-丙二醇

建立了酸水解植物蛋白及酱油中3-氯-1,2-丙二醇(3-MCPD)的固相萃取-气相色谱/质谱测定方法。样品经Aoisa-HBL固相萃取柱萃取,正己烷-乙酸乙酯净化提取,七氟丁酰咪唑衍生,衍生物经气相色谱/负化学电离-质谱（GC/NCI-MS）选择离子模式(SIM)检测,外标法定量。3-MCPD的定量检测限为0.5 μg/kg,平均回收率为92.2%～97.4%,相对标准偏差为3.6%～10.9%。该方法检测灵敏度高,定性定量准确。     

酱油中3-氯-1，2-丙二醇检测实验室间比对分析

介绍了由中国计量科学研究院化学所负责实施的酱油中3-氯-1,2-丙二醇检测实验室间比对情况,并针对该项目的检测方法、标准物质选择、前处理方法等进行了技术分析。21家参加比对实验室对样品l检测结果满意率85．7％,样品2结果满意率100％。建议实验人员在检测中可通过空白加标或应用质控样品等手段提高检测结果的准确度。     

顶空-固相微萃取-气相色谱法测定水蜜桃中有机氯农药

应用顶空-固相微萃取分离、富集,气相色谱法测定了水蜜桃中11种有机氯农药。称取匀浆后的果浆样品5.000g,加水15mL稀释。取此样品溶液2.00mL置于12mL安瓿瓶中,加入氯化钠1.0g,放入搅拌子后将瓶盖紧,置于70℃水浴中。将聚二甲基硅氧烷萃取头插入瓶中,置于离试样液面1.0cm的顶空处,在600r·min-1搅拌速率下萃取30min。萃取完成后,将萃取头从瓶中抽出并直接插入色谱仪的进样口,热解吸5min。被测组分随载气进入SE-54石英毛细管柱进行分离,用电子捕获检测器检测。11种有机氯农药在一定浓度范围内与相应峰面积呈线性关系,检出限(3S/N)在1.33~42.3ng·kg-1之间。对方法的回收率和重复性进行试验,测得回收率在90.6%~112%之间,测定值的相对标准偏差(n=5)均小于10%。     

用GC-M S-SI M法测定酱油中的3-氯-1,2丙二醇

利用气相色谱 -质谱联用离子选择检测法 (GC -MS-SIM)测定酱油中3 -氯 -1,2 -丙二醇(3_CPD),样品用苯硼酸衍生化处理 ,正己烷抽提 ,用HP-112m×0.2mm毛细管色谱柱分离 ,选择基峰离子m/z147进行测定 ,检出限0.001×10-6。该法操作简单 ,快捷 ,灵敏度高。     

Determination of 1,3-dichloro-2-propanol and 3-chloro-1,2-propandiol in soy sauce by headspace derivatization solid-phase microextraction combined with gas chromatography-mass spectrometry

This study proposes a method for identifying 1,3-dichloro-2-propanol and 3-chloro-1,2-propandiol in aqueous matrices by using headspace on-fiber derivatization following solid-phase microextraction combined with gas chromatography-mass spectrometry. The optimized SPME experimental procedures for extracting 1,3-dichloro-2-propanol and 3-chloro-1,2-propandiol in aqueous solutions involved a 85 μm polyacrylate-coated fiber at pH 6, a sodium chloride concentration of 0.36 g mL⁻¹, extraction at 50 °C for 15 min and desorption of analytes at 260 °C for 3 min. Headspace derivatization was conducted in a laboratory-made design with N-methyl-N-(trimethylsilyl)-trifluoroacetamide vapor following solid-phase microextraction by using 3 μL N-methyl-N-(trimethylsilyl)-trifluoroacetamide at an oil bath temperature of 230 °C for 40 s. This method had good repeatability (R.S.D.s ≤ 19%, n = 8) and good linearity (r² ≥ 0.9972) for ultrapure water and soy sauce samples that were spiked with two analytes. Detection limits were obtained at the ng mL⁻¹. The result demonstrated that headspace on-fiber derivatization following solid-phase microextraction was a simple, fast and accurate technique for identifying trace 1,3-dichloro-2-propanol and 3-chloro-1,2-propandiol in soy sauce.     

顶空固相微萃取-气相色谱-质谱联用分析纺织品中挥发性有机物

建立了顶空固相微萃取（HSSPME）-气相色谱（GC）-质谱（MS）联用测定纺织品中甲苯、4-乙烯基环己烯、苯乙烯、萘和1-苯基环己烯5种挥发性有机物（VOCs）的分析方法。选择聚二甲基硅氧烷（PDMS）作为萃取涂层,优化了SPME的萃取条件,包括平衡时间、萃取时间、萃取温度、顶空体积、离子强度、搅拌速度、解吸温度和时间以及GC—MS仪器条件。对于甲苯、4-乙烯基环己烯、苯乙烯、萘和1-苯基环己烯方法线性范围分别为0．087～870、3．32～3320、2．28～2280、0．015～150和0．050～50．0ng／g;检出限分别为0．005、0．042、0．670、0．008和0．011ng／g。实际样品加标回收率在80．1％～122％之间,RSD在0．8％～8．6％之间。方法符合纺织品中痕量VOCs的快速分析要求。     

Extraction and analysis of different Cannabis samples by headspace solid-phase microextraction combined with gas chromatography-mass spectrometry

A headspace solid-phase microextraction combined with GC-MS method was developed for the extraction and analysis of cannabinoids from Cannabis samples. Different commercially available fibres were evaluated; polydimethylsiloxane 100 microm was selected as the most efficient one. In order to enhance sensitivity and reduce analysis time, the sampling temperature was studied and it showed that extraction should be performed at a high temperature (150 degrees C). In relation with the high lipophilicity of cannabinoids, a relatively long desorption time (3 min) was necessary to ensure a total transfer from the fibre into the injection port of the gas chromatograph. The method was finally applied to the extraction of Swiss marijuana samples from different regions. Data treatment by principal component analysis and hierarchical cluster analysis allowed a discrimination of the different batches.     

Analysis of organic compounds in environmental samples by headspace solid phase microextraction

The analysis of samples contaminated by organic compounds is an important aspect of environmental monitoring. Because of the complex nature of these samples, isolating target organic compounds from their matrices is a major challenge. A new isolation technique, solid phase microextraction, or SPME, has recently been developed in our laboratory. This technique combines the extraction and concentration processes into one step; a fused silica fiber coated with a polymer is used to extract analytes and transfer them into a GC injector for thermal desorption and analysis. It is simple, rapid, inexpensive, completely solvent-free, and easily automated. To minimize matrix interferences in environmental samples, SPME can be used to extract analytes from the headspace above the sample. The combination of headspace sampling with SPME separates volatile and semi-volatile analytes from non-volatile compounds, thus greatly reducing the interferences from non-target compounds. This paper reports the use of headspace SPME to isolate volatile organic compounds from various matrices such as water, sand, clay, and sludge. By use of the technique, benzene, toluene, ethyl-benzene, and xylene isomers (commonly known as BTEX), and volatile chlorinated compounds can be efficiently isolated from various matrices with good precision and low limits of detection. This study has found that the sensitivity of the method can be greatly improved by the addition of salt to water samples, water to soil samples, or by heating. Headspace SPME can also be used to sample semi-volatile compounds, such as PAHs, from complex matrices.     

Volatile flavour constituent patterns of Terras Madeirenses red wines extracted by dynamic headspace solid-phase microextraction

A suitable analytical procedure based on static headspace solid-phase microextraction (SPME) followed by thermal desorption gas chromatography-ion trap mass spectrometry detection (GC-(ITD)MS), was developed and applied for the qualitative and semi-quantitative analysis of volatile components of Portuguese Terras Madeirenses red wines. The headspace SPME method was optimised in terms of fibre coating, extraction time, and extraction temperature. The performance of three commercially available SPME fibres, viz. 100 mum polydimethylsiloxane; 85 mum polyacrylate, PA; and 50/30 mum divinylbenzene/carboxen on polydimethylsiloxane, was evaluated and compared. The highest amounts extracted, in terms of the maximum signal recorded for the total volatile composition, were obtained with a PA coating fibre at 30 degrees C during an extraction time of 60 min with a constant stirring at 750 rpm, after saturation of the sample with NaCl (30%, w/v). More than sixty volatile compounds, belonging to different biosynthetic pathways, have been identified, including fatty acid ethyl esters, higher alcohols, fatty acids, higher alcohol acetates, isoamyl esters, carbonyl compounds, and monoterpenols/C(13)-norisoprenoids.     

顶空固相微萃取与气相色谱-火焰热离子检测器联用测定白酒中吡嗪类化合物

应用顶空固相微萃取(HS-SPME)与气相色谱-火焰热离子检测器(GC-FTD)联用技术,建立了快速检测白酒中吡嗪类化合物的方法。本实验对吸附温度、时间及离子强度对萃取效果的影响进行了优化;在优化条件下,吡嗪类化合物在所测范围内具有良好的线性关系(R2>0.99),酒样重复测定的相对标准偏差小于13.6%,检测限小于0.20μg/L,回收率大于80.2%。用该方法测定了茅台酒、郎酒中的吡嗪类化合物。     

Determination of phenols in environmental water samples by ionic liquid-based headspace liquid-phase microextraction coupled with high-performance liquid chromatography

Headspace liquid-phase microextraction (HS-LPME) has been applied to efficient enrichment of phenols such as 2-nitrophenol, 4-chlorophenol, 2,4-dichlorophenol, and 2-naphthol from water samples based on 1-butyl-3-methylimidazolium hexafluorophosphate ([C4MIM][PF6]) as an extractant. Some parameters that may influence HS-LPME were investigated. The linear range was in the range of 0.5-100 microg/L, and the enrichment factors and repeatability (RSD, n = 6) of the proposed method were in the range of 17.2-160.7 and 5.4-8.9%, respectively. The detection limit for each analyte ranged from 0.3 to 0.5 microg/L. Complex matrices of environmental water samples had a small effect on the enrichment, and this problem could be resolved by the addition of sodium ethylene diamine tetraacetate (EDTA) into the samples. The spiked recoveries were in the range of 89.4-114.2%. All these facts demonstrated that the proposed method, with merits of low cost, simplicity, and easy operation, would be a competitive alternative procedure for the determination of such compounds at trace level.     

Analysis of polychlorinated biphenyls in aqueous samples by microwave-assisted headspace solid-phase microextraction

The hyphenated technique namely microwave-assisted headspace solid-phase microextraction (MA-HS-SPME) was developed and studied for the simultaneous extraction/enrichment of polychlorinated biphenyls (PCBs) in aqueous samples prior to the quantification by gas chromatography (GC). The PCBs in aqueous media are extracted onto a solid-phase micro fibre via the headspace with the aid of microwave irradiation. The optimum conditions for obtaining extraction efficiency, such as the extraction time, addition of salts, addition of methanol, ratio of sample to headspace volume, and the desorption parameters were investigated. Experimental results indicated that the proposed MA-HS-SPME method attained the best extraction efficiency under the optimized conditions, i.e., irradiation of extraction solution (20 ml aqueous sample in 40 ml headspace vial with no additions of salt and methanol) under 30 W microwave power for 15 cycles (1 min power on and 3 min power off of each cycle). Desorption at 270 degrees C for 3 min provided the best detection results. The detection limit obtained were between 0.27 and 1.34 ng/l. The correlation coefficient for the linear dynamic range from 1 to 80 ng/l exceeded 0.99 for 18 PCBs.     

Determination of benzene, toluene, ethylbenzene and xylenes in soils by multiple headspace solid-phase microextraction

Multiple headspace-solid phase microextraction (MHS-SPME) is a recently developed technique for the quantification of analytes in solid samples that avoids the matrix effect. This method implies several consecutive extractions from the same sample. In this way, the total area corresponding to complete extraction can be directly calculated as the sum of the areas of each individual extraction when the extraction is exhaustive, or through a mathematical equation when it is not exhaustive. In this paper, the quantitative determination of benzene, toluene, ethylbenzene and xylene isomers (BTEX) in a certified soil (RTC-CRM304, LGC Promochem) and in a contaminated soil by multiple HS-SPME coupled to a gas chromatography-flame ionisation detector (GC-FID) is presented. BTEX extraction was carried out using soil suspensions in water at 30 degrees C with a 75 microm carboxen-polydimethylsiloxane (CAR-PDMS) fibre and calibration was carried out using aqueous BTEX solutions at 30 degrees C for 30 min with the same fibre. BTEX concentration was calculated by interpolating the total peak area found for the soils in the calibration graphs obtained from aqueous solutions. The toluene, ethylbenzene, o-xylene and m,p-xylene concentrations obtained were statistically equal to the certified values.