Enhanced visible-light-driven photodegradation of Acid Orange 7 azo dye in aqueous solution using Fe-N co-doped TiO2

FeN -co-doped TiO₂ photocatalysts are prepared by sol–gel method using titanium tetraisopropoxide, urea and iron(II) acetylacetonate as precursors of titania, nitrogen and iron, respectively. The prepared samples are analysed from chemical-physical point of view by X-ray diffraction (XRD), Raman spectroscopy, UV–Vis diffuse reflectance spectroscopy (UV–Vis DRS), specific surface area measurements and scanning electron microscopy (FESEM). UV–Vis DRS spectra evidence that the co-doping of TiO₂ with N and Fe leads to the narrowing of the band gap value (2.7 eV) with respect to Fe-doped TiO₂ (2.8 eV) and N-doped TiO₂ (2.9–3 eV). XRD patterns show that photocatalysts are mainly in anatase phase and Fe and N ions are successfully incorporated into the TiO₂ lattice. The average crystallite size of Fe-N co-doped TiO₂ is slightly lower than the other samples and equal to about 7 nm and the specific surface area of the co-doped sample results to be 117 m² g⁻¹. Photocatalytic performances of all prepared samples are evaluated by analysing the degradation of Acid Orange 7 azo dye under visible light irradiation. Photocatalytic efficiency obtained using FeN co-doped TiO₂ strongly increases compared to undoped TiO₂, N-doped TiO₂ and Fe-doped TiO₂ photocatalysts. In detail, using the co-doped photocatalyst, dye discoloration and mineralization result equal to about 90 and 83% after 60 min of LEDs visible light irradiation, underlining the best performances of the FeN co-doped TiO₂ photocatalyst both in terms of treatment time and electric energy consumption.     

Synthesis and photocatalytic activity of nanocrystalline TiO2 co-doped with nitrogen and cobalt(II)

Nitrogen-modified cobalt-doped TiO₂ materials were successfully prepared via a modified sol–gel method. The structure and properties of the catalysts were characterized via X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution TEM, ultraviolet–visible light diffuse reflectance spectra (UV–Vis DRS), N₂ adsorption–desorption isotherms, and energy-dispersive X-ray spectroscopy. The XRD patterns of the pure and co-doped TiO₂ samples indicate that the predominant phase was anatase. The average grain size obtained from TEM was approximately 10 nm. The Brunauer–Emmett–Teller analysis results indicate that the specific surface area was 77.7 m² g^?1. The UV–Vis DRS results for the co-doped sample reveal an absorption edge that had been red-shifted to 500 nm. The photocatalytic activities of the samples were evaluated through photodegradation of papermaking wastewater under UV and visible light irradiation. Compared with the cobalt-doped TiO₂ sample and Degussa P25, the 3 mol% N-doped mesoporous N/Co-TiO₂ photocatalyst exhibited the highest photocatalytic activity, which can be ascribed to the synergistic effect of the N and Co co-doping.     

Cooperation among N,F and Fe in tri-doped TiO<Subscript>2</Subscript> photocatalyst

TiO₂ photocatalysts tri-doped with N, F and Fe were synthesized by a sol–gel method. The cooperation of N, F and Fe in tri-doped TiO₂ was verified by monitoring NH₃ decomposition, X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet–visible (UV–Vis) absorption spectroscopy, and by the simulation based on the density functional theory (DFT). The results from NH₃ decomposition revealed that the cooperation of N, F and Fe broadened the optical response of TiO₂ to the visible light range and also enhanced the photocatalytic activity of TiO₂ under UV light. The reusability of the tri-doped TiO₂ sample after three cycles under UV and visible light irradiation was very good. XRD patterns and SEM and HRTEM images indicated that the tri-doped sample was nanometric anatase with a small amount of rutile with an average particle size of 18 nm. Tri-doping with N, F and Fe suppressed the phase transition from anatase to rutile and also resulted in some more lattice defects. XPS analysis showed that the N, F and Fe atoms were doped into the TiO₂ lattice. UV–Vis absorption spectra of the tri-doped TiO₂ showed that its optical absorption edge was moved up to 640 nm and its UV absorption was also enhanced. The DFT results confirmed that the cooperation of Fe 3d and N 2p orbits narrowed the band gap of TiO₂ and the F 2p orbit broadened the upper valence bands. The synergistic electron density around N, F and Fe in tri-doped TiO₂ was capable of enhancing the photochemical stability and reusability of TiO₂.     

Mesoporous titania photocatalyst: effect of relative humidity and aging on the preparation of mesoporous titania and on its photocatalytic activity performance

Mesoporous TiO₂ has been synthesized by the sol–gel method, using a nonionic triblock copolymer P123 as surfactant template under acidic conditions. The as-prepared samples were characterized by thermogravimetry–differential thermal analysis (TG–DTA), nitrogen absorption–desorption (BET), field emission scanning electron microscopy, and transmission electron microscopy. The photocatalytic activity of the mesoporous TiO₂ was evaluated by degradation of methylene blue under high-intensity UV light irradiation; the amount of methylene blue was measured by UV–visible spectroscopy. TG–DTA analysis revealed that the surfactant had been removed partly in as-synthesized samples. BET analysis proved that all the samples retained mesoporosity with a narrow pore-size distribution (4.5–6.3 nm) and high surface area (103–200 m²/g). All calcined mesoporous TiO₂ had high photocatalytic activity in the photodegradation of methylene blue.     

Preparation and photocatalytic activity of B,Ce Co-doped TiO2 hollow fibers photocatalyst

A series of B, Ce co-doped TiO₂ (B, Ce-TiO₂) photocatalytic materials with a hollow fiber structure were successfully prepared by template method using boric acid, ammonium ceric nitrate and tetrabutyltitanate as precursors and cotton fibers as template, followed by calcination at 500°C in an N₂ atmosphere for 2 h. Scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption-desorption measurements, and UV-visible spectroscopy (UV-Vis) were employed to characterize the morphology, crystal structure, surface structure, and optical absorption properties of the samples. The photocatalytic performance of the samples was studied by photodegradation phenol in water under UV light irradiation. The results showed that the TiO₂ fiber materials have hollow structures, and the fiber structure materials showed better photocatalytic properties for the degradation of phenol than pure TiO₂ under UV light. In the experiment condition, the photocatalytic activity of B, Ce co-doped TiO₂ fibers was optimal of all the prepared samples. In addition, the possibility of cyclic usage of B, Ce co-doped TiO₂ fiber photocatalyst was also confirmed, the photocatalytic activity of TiO₂ fibers remained above 90% of that of the fresh sample after being used four times. The material was easily removed by centrifugal separation from the medium. It can therefore be potentially applied for the treatment of water contaminated by organic pollutants.     

Synthesis of visible light-driven Eu, N co-doped TiO2 and the mechanism of the degradation of salicylic acid

Europium and nitrogen co-doped TiO₂ was successfully synthesized by the precipitation–peptization method. The structure and properties of the catalysts were characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, and UV–vis diffuse reflectance spectra. The photocatalytic efficiency was evaluated by monitoring the photocatalytic degradation of salicylic acid under visible light irradiation. It was verified that TiO₂ co-doped with nitrogen and 1% europium showed the highest photocatalytic activity. The adsorption isotherms were obtained by measuring the salicylic acid concentration before and after the dark adsorption at different original solution concentrations. The results illustrated that the doping of Eu was beneficial to the adsorption of salicylic acid. The probable degradation mechanism of salicylic acid was examined by the addition of NaF, Na₂S₂O₃, and K₂S₂O₈ as the probe molecules. It was verified that salicylic acid was first adsorbed on the surface of the catalysts, followed by the degradation by the photogenerated holes (h _vb ⁺ ).     

太阳光下高光催化活性Pr-N-P三元掺杂锐钛矿TiO2纳米片

利用溶胶-凝胶和溶剂热联合技术制备了Pr-N-P三元掺杂锐钛矿TiO₂（PrNPTO）纳米片,并采用X射线衍射、透射电镜、N₂吸附、X射线光电子能谱、UV-vis吸收谱和光致荧光光谱分析技术对其进行了表征.当Pr掺杂量为1.75wt%,焙烧温度为550℃时,制得的PrNPTO在可见和紫外光下光催化降解亚甲基蓝（MB）活性最佳.在模拟太阳光照射下,PrNPTO也表现出优越的光催化降解4-氯酚性能（k_app=3.90×10^-2min^-1）,优于未掺杂、单掺杂和双掺杂TiO₂样品,其光活性是P25TiO₂的3.33倍（k_app=1.17×10^-2min^-1）.PrNPTO光活性的提高归因于Pr-N-P三元掺杂增强了紫外和可见光吸收,降低了光生载流子复合,增加了表面羟基以及改善了表面织构特性.在模拟太阳光照射下,PrNPTO光催化效率高且光催化性能稳定,适合于环境净化领域的实际应用.     

High temperature stability and photocatalytic activity of nanocrystalline anatase powders with Zr and Si co-dopants

TiO₂ nanopowders doped by Si and Zr were prepared by sol–gel method. The effects of Si and Zr doping on the structural, optical, and photo-catalytic properties of titania nanopowders have been studied by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy, and UV–Vis absorption spectroscopy. XRD results suggest that adding impurities has a significant effect on anatase phase stability, crystallinity, and particle size of TiO₂. Titania rutile phase formation in ternary system (Ti–Si–Zr) was inhibited by Zr⁴⁺ and Si⁴⁺ co-doped TiO₂ in high temperatures (500–900 °C) and 36 mol% anatase composition is retained even after calcination at 1,000 °C. The photocatalyst activity was evaluated by photocatalytic degradation kinetics of aqueous methylen orange under visible radiation. The results show that the photocatalytic activity of the 20 %Si and 15 %Zr co-doped TiO₂ nanopowders have a larger degradation efficiency than pure TiO₂ under visible light.     

Enhanced photo-catalytic activity of TiO2 nanostructured thin films under solar light by Sn and Nb co-doping

In this study, preparation of Sn and Nb co-doped TiO₂ dip-coated thin films on glazed porcelain substrates via sol–gel process have been investigated. The effects of co-doping content on the structural, optical, and photo-catalytic properties of applied thin films have been studied by X-ray diffraction (XRD), field emission SEM (FE-SEM), high resolution transmission electron microscopy (HR-TEM), and UV–Vis absorption spectroscopy. Surface chemical state of thin films was examined by atomic X-ray photoelectron spectroscopy (XPS). XRD results suggest that adding impurities has a great effect on the crystallinity and particle size of TiO₂. Titania Rutile phase formation in thin film was promoted by Sn⁴⁺ addition but was inhibited by Nb⁵⁺ doping. The prepared co-doped TiO₂ photo-catalyst films showed optical absorption edge in the visible light area and exhibited excellent photo-catalytic ability for degradation of methylene blue (MB) solution under solar irradiation. Comparison with undoped and Sn or Nb-doped TiO₂, codoped TiO₂ shows an obviously higher catalytic activity under solar irradiation.     

Synthesis of iron-containing nitrogen-doped titania by hydrothermal method and its photocatalytic activity

By a hydrothermal method, iron and nitrogen co-doped TiO₂ and iron oxide impregnated nitrogen-doped TiO₂ were prepared. The obtained Fe and N co-doped TiO₂ showed mixed anatase, rutile, and brookite phases, and high specific surface areas above 160 m²/g. The Fe co-doping was proved to be effective to enhance the visible light absorption ability; however, the photocatalytic activity in deNO _x experiment decreased due to the increase in the amount of lattice vacancy. On the other hand, the photocatalytic activity of N-doped TiO₂ was improved by the impregnation of iron oxide.     

Preparation,Characterization and Photocatalytic Activity of Fe,La Co-doped Nanometer Titanium Dioxide Photocatalysts

A series of photocatalysts of un-doped, single-doped and co-doped nanometer titanium diox-ide (TiO₂) have been successfully prepared by template method using Fe(NO₃)₃·9H₂O, La(NO₃)₃·6H₂O, and tetrabutyl titanate as precursors and glucan as template. Scanning electron microscopy, X-ray diffraction, and N₂ adsorption-desorption measurement were em-ployed to characterize the morphology, crystal structure and surface structure of the samples. The photo-absorbance of the obtained catalysts was measured by UV-Vis absorption spec-troscopy, and the photocatalytic activities of the prepared samples under UV and visible light were estimated by measuring the degradation rate of methyl orange in an aqueous solu-tion. The characterizations indicated that the prepared photocatalysts consisted of anatase phase and possessed high surface area of ca. 163-176 m²/g. It was shown that the Fe and La co-doped nano-TiO₂ could be activated by visible light and could thus be used as an effective catalyst in photo-oxidation reactions. The synergistic effect of Fe and La co-doping played an important role in improving the photocatalytic activity. In addition, the possibil-ity of cyclic usage of co-doped nano-TiO₂ was also confirmed, the photocatalytic activity of codoped nano-TiO₂ remained above 89.6% of the fresh sample after being used four times.     

Plasma-Assisted Synthesis of TiO2 Nanorods by Gliding Arc Discharge Processing at Atmospheric Pressure for Photocatalytic Applications

The present study explores a new method of synthesis of TiO₂ nano-particles in an aqueous medium from TiCl₃ precursor by non-thermal plasma in humid air as feeding gas obtained at atmospheric pressure. The precursor solution, TiCl₃ is oxidized by strongly reactive species generated by gliding arc plasma (HO^· = 2.85 V/SHE) to produce titanium oxide powders. The synthesized powder was characterised by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy, FTIR spectroscopy, nitrogen physisorption, and UV–Vis spectroscopy. The results obtained showed that the material consists of rod-shaped nanoparticles of rutile and anatase phases. The presence of TiO₂ phases was confirmed by FTIR spectrum and textural analyses showed that the material is mesoporous with specific surface area of 158 m² g^?1. UV–Visible spectrum of the plasma-synthesized TiO₂ sample showed that it absorbs in the UV–A region leading to effective use as a photocatalyst under visible light.     

Sol–gel preparation and characterization of Ag and Mg co-doped nano TiO<Subscript>2</Subscript>: efficient photocatalytic degradation of C.I. Acid Red 27

In this study, we successfully prepared pure, mono-doped, and Ag, Mg co-doped TiO₂ nanoparticles using the sol–gel method, with titanium tetraisopropoxide as the Ti source. The prepared samples were characterized by X-ray powder diffraction (XRD), specific surface area and porosity (BET and BJH) measurement, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, photoluminescence, and energy dispersive X-ray spectroscopy techniques. The XRD data showed that the prepared nanoparticles had the same crystals structures as the pure TiO₂. Also, DRS results indicated that the band gap of co-doped photocatalyst was smaller than that of the monometallic and undoped TiO₂ and that there was a shift in the absorption band towards the visible light region. Furthermore, the photocatalytic activity of the prepared catalysts was evaluated by the degradation of C.I. Acid Red 27 in aqueous solution under visible light irradiation. The results showed that Ag (0.08 mol%), Mg (0.2 mol%) co-doped TiO₂ had the highest photoactivity among all samples under visible light. It was concluded that co-doping of the Ag and Mg can significantly improve the photocatalytic activity of the prepared photocatalysts, due to the efficient inhibition of the recombination of photogenerated electron–hole pairs. The optimum calcination temperature and time were 450 °C and 3 h, respectively.     

具有高可见光催化活性的Ti3+和碳共掺杂改性的TiO2光催化剂

以乙醇为碳源,采用操作简单的真空活化法一步实现对TiO₂的Ti³⁺与C的共掺杂改性,TiO₂用X衍线衍射、紫外-可见光谱、顺磁共振、X射线光电子能谱和红外光谱等手段表征了催化剂的结构、组成、光学性质. 结果表明, 经Ti³⁺与C共掺杂改性后的催化剂表现出高的可见光降解甲基橙活性. 复合在催化剂表面的石墨可以增强催化剂对可见光的响应范围,而Ti³⁺与氧缺陷形成的掺杂能级则可以提高光生电子的迁移效率. 实验表明,两者之间的协同作用促进了其可见光催化活性的提高.     

Synthesis of anatase TiO2 in a vinyl-containing ionic liquid and its enhanced photocatalytic activity

TiO₂ microspheres were synthesized by the sol–gel method using the ionic liquid (IL) 1-vinyl-3-propylimidazolium iodide (VPIM⁺I^?) as a reaction medium, then calcined at 500 °C. The samples were characterized by X-ray diffraction, scanning electron microscopy, and ultraviolet–visible (UV–Vis) diffuse reflectance spectroscopy. The phase of TiO₂ microspheres is anatase, and VPIM⁺I^? is able to favor the growth of anatase phase and prevents the collapse of small pores. The photocatalytic activity of TiO₂-IL was tested by degradation of 2-nitrophenol under UV light illumination. The photocatalytic activity of TiO₂-IL was higher than that of samples prepared in the reaction medium without VPIM⁺I^?.     

Enhanced photoinduced super-hydrophilicity in sol–gel TiO2 thin films with co-doped Sn/Nb

In this work, Sn and Nb co-doped TiO₂ were coated on glazed porcelain substrates via sol–gel dip coating method. Field emission-scanning electron microscopy, transmission electron microscopy, and UV–vis spectrophotometer were used to evaluate thickness and optical properties of the thin films. Surface chemical state of thin films was examined by atomic X-ray photoelectron spectroscopy. Water contact angle on the film surfaces was measured by a contact angle analyzer under solar light irradiation. The optical results indicated that Sn/Nb dopant in TiO₂ thin film changed the absorption edge from ultraviolet to visible light and exhibited excellent photo-catalytic ability for degradation of methylene blue solution under solar irradiation. Wettability results indicated that Sn and Nb dopant ions had significant effect on the hydrophilicity property of thin films.     

Synthesis and photocatalytic activity of co-doped mesoporous TiO2 on Brij98/CTAB composite surfactant template

Using composite surfactant templates, polyoxyethylene (20) oleyl ether (Brij98) and cetyl trimethyl ammonium bromide (CTAB), as structure-directing agents, N and La co-doped mesoporous TiO₂ complex photocatalysts were synthesized successfully. The micromorphology of co-doped mesoporous TiO₂ samples was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transformed infrared spectroscopy (FT-IR), energy-dispersive X-ray spectrometer (EDS) and N₂ adsorption-desorption measurements. The results indicated that the complex photocatalyst prepared with a molar ratio of Brij98:CTAB=1:1 showed a uniform pore size of ca. 7 nm and a high specific surface area (S_BET) of 279.0 m² g⁻¹, and exhibited the highest photocatalytic activity for degradation of papermaking wastewater under ultra-violet light irradiation. The chemical oxygen demand (CODc_r) percent degradation was about 73% in 12 h and chroma percent degradation was 100% in 8 h.     

Synthesis,characterization and photocatalytic performance of W,N, S-tri-doped TiO2 under visible light irradiation

W–S–N-tri-doped TiO₂ photocatalysts (WSNTiO₂) were prepared by a simple sol–gel method. Tungstic acid, sodium sulfate and urea were used as tungsten, sulfur and nitrogen sources, respectively. The morphology and microstructure characteristics of the photocatalysts were evidenced by means of XRD, BET, TEM, SEM and UV–vis DRS techniques. The XRD results show that the main crystal phase of samples is anatase. It was also found that the tri-doping of TiO₂ increases its BET specific surface area from 95 to 121 m²·g⁻¹. Besides, it was shown that tri-doping narrows the band gap of TiO₂ effectively, which has greatly improved the photocatalytic activity in the visible light region. The photocatalytic activity of tri-doped TiO₂ powders was compared to that of bi-doped ones through the degradation of Congo Red (CR) under visible irradiation. Thus, the prepared 0.5% W–N–S–TiO₂ heat treated at 450 °C showed the best photocatalytic activity compared to the prepared pure TiO₂, Degussa P25, and co-doped samples (WNTiO₂ and WSTiO₂). In particular, a Congo Red degradation rate of approximately 99% was reached after only 35 min of visible light irradiation in the presence of 0.5% of WNSTiO₂. Total organic carbon (TOC) removal of CR was up to 72% and confirmed its significant mineralization in the presence of 0.5% of WNSTiO₂ photocatalyst.     

Metal–metal charge transfer and interfacial charge transfer mechanism for the visible light photocatalytic activity of cerium and nitrogen co-doped TiO2

Nanosized cerium and nitrogen co-doped TiO₂ (Ce–TiO_2?xN_x) was synthesized by sol gel method and characterized by powder X-ray diffraction (PXRD), X-ray photoelectron spectroscopy (XPS), FESEM, Fourier transform infrared, N₂ adsorption and desorption methods, photoluminescence and ultraviolet–visible (UV–vis) DRS techniques. PXRD analysis shows the dopant decreases the crystallite sizes and slows the crystallization of the titania matrix. XPS confirm the existence of cerium ion in +3 or +4 state, and nitrogen in ?3 state in Ce–TiO_2?xN_x. The modified surface of TiO₂ provides highly active sites for the dyes at the periphery of the Ce–O–Ti interface and also inhibits Ce particles from sintering. UV–visible DRS studies show that the metal–metal charge transfer (MMCT) of Ti/Ce assembly (Ti⁴⁺/Ce³⁺ → Ti³⁺/Ce⁴⁺) is responsible for the visible light photocatalytic activity. Photoluminescence was used to determine the effect of cerium ion on the electron–hole pair separation between the two interfaces Ce–TiO_2?xN_x and Ce₂O₃. This separation increases with the increase of cerium and nitrogen ion concentrations of doped samples. The degradation kinetics of methylene blue and methyl violet dyes in the presence of sol gel TiO₂, Ce–TiO_2?xN_x and commercial Degussa P25 was determined. The higher visible light activity of Ce–TiO_2?xN_x was due to the participation of MMCT and interfacial charge transfer mechanism.     

Enhancement of visible-light photocatalytic activity of Cu-doped TiO<Subscript>2</Subscript> nanoparticles

Bare TiO₂ and Cu-doped TiO₂ nanoparticles with different nominal doping amounts of Cu ranging from of 0.5 to 5.0 mol% were synthesized using the modified sol–gel method. The samples were physically characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer–Emmett–Teller-specific surface area, UV–Vis diffuse reflectance spectroscopy, zeta potential, X-ray photoelectron spectroscopy, inductively coupled plasma, and photoluminescence techniques. The Cu-doped TiO₂ exhibited good photocatalytic activity in mineralization of oxalic acid and formic acid under visible light irradiation. Photomineralization of oxalic and formic acids under visible light irradiation revealed greatly enhanced photoactivity exhibited by the 2.0 mol% Cu-doped TiO₂ photocatalyst compared to bare TiO₂ . The enhanced photocatalytic performance arises from copper ion doping in the TiO₂ structure, leading to an extended photoresponsive range, enhanced photogenerated charge separation, and transportation efficiency.