氧化锌薄膜光电功能材料研究的关键问题

氧化锌薄膜光电功能材料是近年来新发展起来的研究课题,由于它在短波长光电信息功能材料方面具有潜在的应用前景而备受关注.为了开发ZnO结型光电器件,目前首先需要解决高质量ZnO单晶薄膜的外延及p型掺杂等关键问题.综合国内外的研究结果,结合我们的工作,叙述了利用多晶格匹配原理通过过渡层在Si衬底上异质外延高质量ZnO薄膜,介绍了用SiC作过渡层生长ZnO薄膜的有关问题.对ZnO的p型掺杂,分析了制备p型ZnO的困难和利用Ⅲ-Ⅴ族共掺杂方法生长p型ZnO的作用和优点.     

非晶硅太阳电池光照J-V特性的AMPS模拟

运用AMPS(Analysis of Microelectronic and Photonic Structures)模拟分析了TCO/p_a_SiC:H/i_a_Si:H/n_a_Si:H/metal结构的异质结非晶硅太阳电池中的p/i界面的价带失配以及TCO/p,n/metal界面接触势垒对电池光电特性的影响.分析总结了非晶硅基薄膜太阳电池中J-V曲线异常拐弯现象的种类和可能原因.     

氮等离子体辅助脉冲激光沉积生长p型ZnO:N薄膜的光学和电学性质

通过氮气等离子体辅助脉冲激光沉积(PLD)技术制备了氮掺杂氧化锌(ZnO:N)薄膜.经过低温快速热退火(RTA)处理后,ZnO:N薄膜呈现p型导电特性.利用X射线光电子能谱(XPS)、光致发光(PL)和霍尔测量对ZnO:N薄膜中N的化学状态及其光学和电学性质进行了系列的研究.结果表明:所制得的p型ZnO:N薄膜为高度补...     

衬底温度和硼掺杂对p型氢化微晶硅薄膜结构和电学特性的影响

以B₂H₆为掺杂剂,采用射频等离子体增强化学气相沉积技术在玻璃衬底上制备p型氢化微晶硅薄膜.研究了衬底温度和硼烷掺杂比对薄膜的微结构和暗电导率的影响.结果表明：在较高的衬底温度下很低的硼烷掺杂比即可导致薄膜非晶化;在实验范围内,随着衬底温度升高薄膜的晶化率单调下降,暗电导率先缓慢增加然后迅速下降,变化趋势与硼烷掺杂比的影响极为相似.最后着重讨论了p型氢化微晶硅薄膜的生长机理. 关键词： p型氢化微晶硅薄膜 衬底温度 晶化率 电导率     

n型窗口层材料及其在高速沉积微晶硅太阳电池中的应用研究

采用常规的射频等离子体增强化学气相沉积技术制备了可以用于微晶硅薄膜太阳电池的n型的掺杂窗口层材料.通过掺杂窗口层材料在电池中的应用发现：微晶硅薄膜太阳电池由于其电子和空穴的迁移率相差比较小而显示出磷掺杂的n型的微晶硅材料也可以像硼掺杂的p型的微晶硅材料一样,可作为微晶硅薄膜太阳电池的窗口层材料;两种窗口层制备电池的效率差别不大,而且量子效率（QE）测试结果显示两种电池的n/i和p/i界面没有明显的区别;电池的双面不同波长拉曼光谱的测试结果给出：不论是n/i/p还是p/i/n型的电池,在起始生长本征层阶段均 关键词： n型的掺杂窗口层 p型的掺杂窗口层 微晶硅薄膜太阳电池     

p型ZnO薄膜的制备及特性

采用射频磁控溅射在Si片上制备ZnO薄膜，通过离子注入对样品进行N掺杂，在不同温度下进行退火并实现了p型转变.用扫描电子显微镜、X射线衍射和Hall测量对薄膜进行了表征，结果表明薄膜具有良好的表面形貌和高度c轴择优取向，退火后p型ZnO薄膜的最高载流子浓度和最低电阻率分别为1.68×10¹⁶cm^-3和41.5Ω·cm.讨论并分析了退火温度和时间对ZnO薄膜p型转变的影响.     

离子束增强沉积制备p型氧化锌薄膜及其机理研究

采用离子束增强沉积方法在Si和SiO₂/Si衬底上制备In-N共掺杂ZnO薄膜(INZO)，溅射靶是用ZnO和2 atm% In₂O₃粉体均匀混合并压制而成，在氩离子溅射ZnO靶的同时，氮、氩混合离子束垂直注入沉积的薄膜.实验结果显示INZO薄膜具有(002)的择优取向，并且为p型导电，电阻率最低为0.9Ωcm.薄膜在氮气、氧气气氛下退火，对薄膜的结构和电学特性与成膜和退火条件的关系进行了分析. 关键词： 氧化锌薄膜 p型掺杂 离子束增强沉积     

Ag掺杂p型ZnO薄膜及其光电性能研究

采用超声喷雾热分解法在石英衬底上以醋酸锌水溶液为前驱体,以硝酸银水溶液为Ag掺杂源生长了Ag掺杂ZnO(ZnO：Ag)薄膜.研究了衬底温度对所得ZnO：Ag薄膜的晶体结构、电学和光学性质的影响规律.所得ZnO：Ag薄膜结构良好,在室温光致发光谱中检测到很强的近带边紫外发光峰,透射光谱中观测到非常陡峭的紫外吸收截止边和较高的可见光区透过率,表明薄膜具有较高的晶体质量与较好的光学特性.霍尔效应测试表明,在500℃下获得了p型导电的ZnO：Ag薄膜,载流子浓度为5.30×10¹⁵cm关键词： ZnO：Ag薄膜 p型掺杂 超声喷雾热分解 霍尔效应     

一种具有减反射性能的Cu2ZnSnS4太阳能电池透明导电氧化物薄膜

通过研究一种新型透明导电氧化物薄膜(transparent conductive oxide, TCO)的减反射作用,探索增加入射光进入Cu₂ZnSnS₄ (CZTS)太阳能电池从而提高太阳能电池效率的新途径.在AM1.5光照条件下,设计了一种在宽波长范围内具有更好的减反射性能的TCO薄膜,即SiO₂/ZnO减反射TCO薄膜(antireflective transparent conductive oxide, ATCO).为了衡量300—800 nm波长范围内的减反射效果,引入了有效平均反射率方法 (effective average reflectance, EAR)进行测算.为充分考虑折射率色散的影响以及TCO, ATCO薄膜与有源层的耦合,本文采用多维光学传输矩阵对各关键材料层的耦合及膜厚进行了优化,以准确衡量最优的减反射效果.最后,通过比较常规CZTSSC和ATCO-CZTSSC的减反射性能,得到了新型ATCO膜,可以有效地减少光损耗并提高光电转换效率的结论.     

牺牲Ni退火对硅衬底GaN基发光二极管p型接触影响的研究

本文通过在硅衬底发光二极管(LED)薄膜p-GaN表面蒸发不同厚度的Ni覆盖层,将其在N₂ ∶O₂=4 ∶1的气氛中、400℃—750℃的温度范围内进行退火,在去掉薄膜表面Ni覆盖层之后制备Pt/p-GaN欧姆接触层.实验结果表明:退火温度和Ni覆盖层厚度均对硅衬底GaN基LED薄膜p型欧姆接触有重要影响,Ni覆盖退火能够显著降低p型层中Mg受主的激活温度.经牺牲Ni退火后,p型比接触电阻率随退火温度的升高呈先变小后变大的规律,随Ni覆盖层厚度的增加呈先变小后变 关键词： 氮化镓 发光二极管 牺牲Ni退火 p型接触     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.