基于金纳米粒子/Fe-MIL-88-NH2的比率型C反应蛋白免疫传感器

以金纳米粒子(Au nanoparticles, AuNPs)功能化的金属有机骨架材料(Fe-MOFs, Fe-MIL-88-NH₂)为基质材料,构建了双信号比率型免疫传感器,用于C-反应蛋白(C-reactive protein,CRP)的检测。八面体结构的Fe-MOFs不仅提供了较大的有效表面积,可增加固定生物分子的量,促进电子和离子的传输,而且表现出良好的导电性。将AuNPs修饰到Fe-MOFs上可以进一步增加比表面积,以捕获大量抗体以及提高电子转移能力。随CRP浓度的增加,K₃Fe(CN)₆/K₄Fe(CN)₆的氧化峰电流减小,而Fe-MOFs的氧化峰电流相对恒定。采用K₃Fe(CN)₆/K₄Fe(CN)₆响应电流与Fe-MOFs的响应电流比值作为定量测定CRP的响应信号。以K₃Fe(CN)₆/K₄Fe(CN)     

氮掺杂石墨烯的制备及氧还原电催化性能

采用两步热解法, 用尿素掺杂氧化石墨烯(GO)得到N掺杂的还原氧化石墨烯(N-RGO), 通过控制反应温度, 制备了具有不同电催化活性的N掺杂的还原氧化石墨烯. 透射电子显微镜(TEM)和扫描电子显微镜(SEM)结果显示, 制得的氮掺杂石墨烯(nG)表面褶皱和重叠增加. X射线光电子能谱(XPS)证明, 氮元素以吡啶N、 吡咯N和石墨化的N 3种形式掺杂在石墨烯中, 最高摩尔分数为6.6%. 通过循环伏安(CV)和旋转圆盘电极(RDE)测试了nG的电化学性能, 结果表明, 在酸性电解质中对氧还原(ORR)有较高的催化活性, 起始电位在0.1 V左右, 电催化还原氧气时主要为四电子反应, 且相对商用的Pt/C催化剂有更好的电化学稳定性, 其中第一步热解温度为200℃制得的nG催化性能最好.     

[Fe(CN)6]4-在溴碘化银T-颗粒乳剂中的掺杂

本文研究了K₄[Fe(CN)₆]掺杂对溴碘化银T-颗粒乳剂感光性能的影响.结果表明,掺杂剂的掺杂量以及掺杂位置对乳剂的感光性能都有影响.K₄[Fe(CN)₆]的掺杂量在每克乳剂31×10^-9-31×10^-11mol之间时,乳剂感光度都有提高.最佳掺杂量为每克乳剂31×10-10mol.掺杂位置接近表面时效果相对较好,表明K₄[Fe(CN)₆]是浅电子陷阱掺杂剂.当掺杂剂的掺杂量大于每克乳剂31×10^-8mol,且掺杂位置在乳剂颗粒较深内部时,乳剂的感光度反而下降.     

不同氮掺杂石墨烯氧还原反应活性的密度泛函理论研究

N掺杂石墨烯作为一种具有较高活性和稳定性的氧还原反应(ORR)催化剂,受到人们的广泛关注。然而不同的N掺杂类型对氧还原活性的影响一直存在争议。本文通过密度泛函理论分别对石墨型和吡啶型两种N掺杂石墨烯的ORR活性进行比较研究。能带结构分析表明,石墨氮掺杂石墨烯(GNG)的导电性随掺N量的增加而降低;吡啶氮掺杂石墨烯(PNG)的导电性则随掺N量的增加先提高后降低。当N掺杂浓度达到4.2%(原子分数)时,PNG具有最优导电性。且当N掺杂浓度大于1.4%时,PNG的导电率总是高于GNG。氧还原自由能阶梯曲线发现O₂的质子化是整个氧还原过程的潜在控制步骤。在同等氮掺杂浓度下,O₂的质子化自由能能变在GNG上低于在PNG上,意味着若在同等电子传输能力的情况下,GNG具有比PNG更优异的催化活性。进一步分析发现：当N掺杂浓度在低于2.8%时,GNG和PNG导电性差异小,其催化ORR活性由O₂质子化反应难易程度决定,GNG的催化活性优于PNG;当N掺杂浓度高于2.8%时,氮掺杂石墨烯的电子传输性能(导电性)成为决定催化剂ORR活性的主要因素,因此PNG表现出较GNG更高的活性。     

碱性电解液中K3[Fe(CN)6]在锌阳极上的自发还原和吸附延长锌镍电池的循环寿命

采用K₃[Fe(CN)₆]作为锌镍电池的电解液添加剂,克服了锌阳极的变形。此外,通过一系列实验设计和表征,探索了电解液中金属锌与K₃[Fe(CN)₆]的反应机理。通过XRD (X-ray diffraction)和XPS (X-ray photo-electron spectroscopy)测试,我们发现金属锌在KOH水溶液中能够与K₃[Fe(CN)₆]反应,将[Fe(CN)₆]^3–还原为[Fe(CN)₆]⁴⁻。添加K₃[Fe(CN)₆]的锌镍电池实现了更长的循环寿命,比不添加K₃[Fe(CN)₆]的锌镍电池长3倍以上。在相同循环次数下,改性电解质中锌阳极循环不仅形状变化较小,而且没有出现“死”锌现象,电极添加剂和粘结剂也没有发生偏析。此外,不同于一般的有机添加剂,K₃[Fe(CN)₆]的加入不仅不会增大电极的极化,还能够提高锌镍电池的放电容量和倍率性能。因此,考虑到这一改性策略有着较高的可行性和较低的成本,K₃[Fe(CN)₆]添加剂在锌镍电池的实际应用中具有极大的推广潜力。     

辣根过氧化物酶的电化学固定化及其对H2O2的生物电催化还原作用

利用电化学固定化方法制备了聚吡咯/辣根过氧化物酶(PP/HRP)膜电极,并研究了其电化学行为。在除氧的磷酸盐缓冲液介质中,PP/HRP电极加速H₂O₂的还原,归因于酶加成物的直接电子传递。探索HRP与电子传递体K₄Fe(CN)₆在聚吡咯(PP)膜中的同时固定化条件及其膜电极的电化学行为,实验证实,K₄Fe(CN)₆在酶膜中的存在使得H₂O₂的还原电位强烈正移,在-0.05V的工作电位下能对H₂O₂进行检测,相应的电极过程可用间接氧化还原催化机理解释。     

Co3O4/聚吡咯/石墨烯碱性溶液中电化学还原氧

燃料电池具有较高的能量密度和发电效率,以清洁能源为原料,零污染排放,是一种具有发展前景的能量储存和转化装置.阴极氧还原反应(ORR)在燃料电池中起着关键作用.ORR广泛采用贵金属铂基催化剂,但是它们价格昂贵,电子动力学转移速率慢,碱性条件下易团聚,这些亟需解决的问题阻碍了燃料电池商业化进程.近期,一些非贵金属催化剂被广泛研究,例如氮掺杂碳材料、Fe/N/C和Co/N/C材料等,它们有可能在未来替代铂基催化剂.我们的目标是合成新型高催化活性的Co/N/C及其衍生非贵金属材料,用于ORR催化反应.由于石墨烯具有独特的形貌、较大的比表面积和良好的导电性,其表面含有功能化的官能团,所以我们选择石墨烯作为碳载体.首先,用改性休克尔方法合成了氧化石墨烯(GO),为了提高其催化活性,采用聚吡咯作为氮源对其进行了氮掺杂,制备了聚吡咯/氧化石墨烯(Ppy/GO).通过ORR催化性能测试发现,GO对ORR具有一定的催化活性,它的起始电位和阴极电流电位分别为–0.31 V vs SCE和–0.38 V vs SCE;Ppy/GO的起始电位和阴极电流电位分别为–0.20 V vs SCE和–0.38 V vs SCE,氮掺杂对GO的催化活性有所提高.采用水热法沉积氧化钴合成了Co3O4/聚吡咯/氧化石墨烯(Co3O4/Ppy/GO).其形貌为Co3O4分散在氮掺杂GO表面.在KOH电解质(0.1 mol/L)中测试,Co3O4/Ppy/GO的起始电位和阴极电流电位分别为–0.20 V和–0.38 V vs SCE.经过800℃高温煅烧处理后,Co3O4/Ppy/GO-800的催化活性明显提高,起始电位和阴极电流电位分别达到–0.10 V和–0.18 V vs SCE.ORR电子转移数为3.4,接近于4电子反应途径.Co3O4/Ppy/GO对ORR的催化活性及4电子催化选择性较高,可能是由于纳米形态的Co3O4和Ppy/GO之间具有较强的表面作用力,聚吡咯掺杂的氧化石墨烯具有较强的电子储存及释放能力.综上,我们通过水热法制备了钴、氮共掺杂的GO,并研究了其对ORR的催化活性和电子转移选择性.结果表明Co3O4/Ppy/GO是一种高效的非贵金属电催化剂,在碱性电解质中具有很高的ORR催化活性,在燃料电池阴极催化剂方面很有前景.     

Fe-N共掺杂纳米碳材料的形貌对电化学还原反应的影响

众所周知,石墨烯片（GS）和碳纳米管是能源转化和储存应用中有效的催化剂. 然而,过渡金属基氮（N）掺杂的体系中经常形成GS和碳纳米管的复合物,使得该体系内的构效关系研究变得十分困难. 为了可控制备出含有理想物种的催化剂,作者尝试通过利用氮对碳纳米管生长的效应调节生成产物的形貌. 本文中,作者采用一步法制备了一系列Fe-N共掺杂的GS、GS/竹节碳纳米管(BCNTs)复合物及BCNTs催化剂. 为了评估碳形貌对催化剂性能的影响,作者采用氧气还原反应（ORR）及二氧化碳还原反应（CO₂RR）作为模型反应. 电化学测试结果表明,所有的样品当中仅含BCNTs的催化剂表现出最好的ORR活性（起始电位E_onset = 1.02 V_RHE）及CO₂RR活性（CO生成法拉第效率FE_CO = 91.1%,-0.6 V_RHE）. 进一步的研究表明,优异的活性与独特的BCNTs中存在的缺陷、较大的比表面积、高含量的吡啶N及FeN_x相关. 该工作加深了作者对形貌相关的ORR及CO₂RR过程的认识和理解.     

Co_3O_4/聚吡咯/石墨烯碱性溶液中电化学还原氧（英文）

燃料电池具有较高的能量密度和发电效率,以清洁能源为原料,零污染排放,是一种具有发展前景的能量储存和转化装置.阴极氧还原反应(ORR)在燃料电池中起着关键作用.ORR广泛采用贵金属铂基催化剂,但是它们价格昂贵,电子动力学转移速率慢,碱性条件下易团聚,这些亟需解决的问题阻碍了燃料电池商业化进程.近期,一些非贵金属催化剂被广泛研究,例如氮掺杂碳材料、Fe/N/C和Co/N/C材料等,它们有可能在未来替代铂基催化剂.我们的目标是合成新型高催化活性的Co/N/C及其衍生非贵金属材料,用于ORR催化反应.由于石墨烯具有独特的形貌、较大的比表面积和良好的导电性,其表面含有功能化的官能团,所以我们选择石墨烯作为碳载体.首先,用改性休克尔方法合成了氧化石墨烯(GO),为了提高其催化活性,采用聚吡咯作为氮源对其进行了氮掺杂,制备了聚吡咯/氧化石墨烯(Ppy/GO).通过ORR催化性能测试发现,GO对ORR具有一定的催化活性,它的起始电位和阴极电流电位分别为–0.31 V vs SCE和–0.38 V vs SCE;Ppy/GO的起始电位和阴极电流电位分别为–0.20 V vs SCE和–0.38 V vs SCE,氮掺杂对GO的催化活性有所提高.采用水热法沉积氧化钴合成了Co_3O_4/聚吡咯/氧化石墨烯(Co_3O_4/Ppy/GO).其形貌为Co_3O_4分散在氮掺杂GO表面.在KOH电解质(0.1 mol/L)中测试,Co_3O_4/Ppy/GO的起始电位和阴极电流电位分别为–0.20 V和–0.38 V vs SCE.经过800°C高温煅烧处理后,Co_3O_4/Ppy/GO-800的催化活性明显提高,起始电位和阴极电流电位分别达到–0.10 V和–0.18 V vs SCE.ORR电子转移数为3.4,接近于4电子反应途径.Co_3O_4/Ppy/GO对ORR的催化活性及4电子催化选择性较高,可能是由于纳米形态的Co_3O_4和Ppy/GO之间具有较强的表面作用力,聚吡咯掺杂的氧化石墨烯具有较强的电子储存及释放能力.综上,我们通过水热法制备了钴、氮共掺杂的GO,并研究了其对ORR的催化活性和电子转移选择性.结果表明Co_3O_4/Ppy/GO是一种高效的非贵金属电催化剂,在碱性电解质中具有很高的ORR催化活性,在燃料电池阴极催化剂方面很有前景.     

CoPy/C催化氧还原的碱效应及活性位研究

以碳黑(Vulcan XC-72R)为载体, 硫酸钴(CoSO₄ · 7H₂O)和吡啶(Py)作为催化剂前躯体, 经溶剂分散及800℃热处理可制备出高效催化氧还原反应(ORR)的碳载钴吡啶复合催化剂(15%Co25%Py/C, 质量分数). 采用红外光谱(IR)和X射线光电子能谱(XPS)等对催化剂的结构进行表征. 运用旋转圆盘电极(RDE)技术研究了不同浓度的KOH溶液(0.05~12.0 mol/L)对CoPy/C催化氧还原活性的影响. 结果表明, 不同浓度的KOH溶液对CoPy/C催化剂催化氧还原反应(ORR)的性能影响很大, 在0.05和0.1 mol/L KOH溶液中催化剂活性最高. 以其制备的气体扩散电极在0.05 mol/L KOH溶液(O₂气氛)中的半波电位为-0.138 V, 起峰电位为0.10 V, 同时表现出明显的极限扩散电流. 在-0.381 V时电流密度达到最大值(4.39 mA/cm²). 随着KOH溶液浓度的增加(pH值下降), 起始电压沿负方向移动, 同时动力学、 混合动力学和扩散区的电流密度均下降. RDE研究结果表明, 在0.05和0.1 mol/L KOH溶液中, O₂在CoPy/C电极上的还原主要经4e^-过程还原成H₂O. XPS研究结果表明, 吡啶作为小分子富氮源对提高催化剂的活性具有重要作用, 所制备催化剂经800℃高温热处理形成了石墨N, 吡啶N以及部分氧化态的氮结构, 其中石墨N和吡啶N作为催化剂的活性中心, 提供氧还原活性位, 从而使该类催化剂对氧还原表现出很好的电催化性能和选择性.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.