等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

新型钴-聚吡咯-碳载Pt燃料电池催化剂的制备与表征

采用脉冲微波辅助化学还原法制备了钴-聚吡咯-碳(Co-PPy-C)载Pt催化剂(Pt/Co-PPy-C),其中Pt的总质量占20%.利用透射电镜(TEM)、光电子射线能谱分析(XPS)和X射线衍射(XRD)研究了催化剂的结构,用循环伏安(CV)、线性扫描伏安(LSV)等方法考察了其电化学活性及氧还原反应(ORR)动力学特性及耐久性.Pt/Co-PPy-C电催化剂的金属颗粒直径约1.8 nm,略小于商用催化剂Pt/C(JM)颗粒尺寸(约2.5 nm);催化剂在载体上分散均匀,粒径分布范围较窄.Pt/Co-PPy-C的电化学活性比表面积(ECSA)(75.1 m2·g-1)高于商用催化剂的ECSA(51.3 m2·g-1).XPS测试表明,自制催化剂表面的Pt主要以零价形式存在.而XRD结果显示,自制催化剂中Pt(111)峰最强,Pt主要为面心立方晶格.Pt/Co-PPy-C具有与Pt/C(JM)相同的半波电位;在0.9 V下,Pt/Co-PPy-C的比活性(1.21 mA·cm-2)高于商用催化剂的比活性(1.04 mA·cm-2),表现出更好的ORR催化活性.动力学性能测试表明催化剂的ORR反应以四电子路线进行.CV测试1000圈后,Pt/Co-PPy-C和Pt/C(JM)的ECSA分别衰减了13.0%和24.0%,可见自制催化剂的耐久性高于商用Pt/C(JM),在质子交换膜燃料电池(PEMFC)领域有一定的应用前景.     

合成具有高氧还原反应催化活性的结构有序铂铁合金催化剂

为提高燃料电池用贵金属铂催化氧还原反应性能,采用改进的多元醇法制备不同金属比例的碳载铂铁合金催化剂（D-Pt₃Fe/C和D-PtFe/C）前驱体. 随后通过优化在惰性气体环境中的高温煅烧条件,将结构无序的合金结构转变为结构有序的合金催化剂（O-Pt₃Fe/C和O-PtFe/C）. 利用X射线粉末衍射（XRD）、透射电子显微镜（TEM）、电感耦合等离子体原子发射光谱（ICP-AES）和X射线光电子能谱（XPS）对所制得催化剂进行结构表征. 结果发现,所制得催化剂的合金纳米颗粒尺寸分布均一（4 ~ 6 nm）,且均匀负载于碳载体上. 利用循环伏安法（CV）、线性扫描伏安法（LSV）对所制得催化剂进行电化学性能评估. 结果表明,O-PtFe/C的催化活性高于O-Pt₃Fe/C,其质量活性（271.54 mA•g^-1_Pt）和比活性（0.73 mA•cm^-2_Pt）分别是商业JM Pt/C催化剂的4.3倍和7.3倍. 两种结构有序铂铁催化剂催化氧还原反应活性均高于商业JM Pt/C催化剂.     

新型钴-聚吡咯-碳载Pt燃料电池催化剂的制备与表征

采用脉冲微波辅助化学还原法制备了钴-聚吡咯-碳（Co-PPy-C）载Pt 催化剂（Pt/Co-PPy-C）,其中Pt 的总质量占20%. 利用透射电镜（TEM）、光电子射线能谱分析（XPS）和X射线衍射（XRD）研究了催化剂的结构,用循环伏安（CV）、线性扫描伏安（LSV）等方法考察了其电化学活性及氧还原反应（ORR）动力学特性及耐久性. Pt/Co-PPy-C电催化剂的金属颗粒直径约1.8 nm,略小于商用催化剂Pt/C（JM）颗粒尺寸（约2.5 nm）;催化剂在载体上分散均匀,粒径分布范围较窄. Pt/Co-PPy-C的电化学活性比表面积（ECSA）（75.1 m²·g^-1）高于商用催化剂的ECSA（51.3 m²·g^-1）. XPS测试表明,自制催化剂表面的Pt 主要以零价形式存在. 而XRD结果显示,自制催化剂中Pt（111）峰最强,Pt 主要为面心立方晶格. Pt/Co-PPy-C具有与Pt/C（JM）相同的半波电位;在0.9 V下,Pt/Co-PPy-C的比活性（1.21 mA·cm^-2）高于商用催化剂的比活性（1.04 mA·cm^-2）,表现出更好的ORR催化活性.动力学性能测试表明催化剂的ORR反应以四电子路线进行. CV测试1000 圈后,Pt/Co-PPy-C和Pt/C（JM）的ECSA 分别衰减了13.0%和24.0%,可见自制催化剂的耐久性高于商用Pt/C（JM）,在质子交换膜燃料电池（PEMFC）领域有一定的应用前景.     

电沉积制备MnO2催化剂及其在微生物燃料电池中的应用

通过电沉积的方法获得了一种具有均匀孔隙结构的海绵状二氧化锰催化剂,结合扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)等手段表征了所制备材料的表面形貌、结构及元素构成和赋存价态,采用线性伏安扫描(LSV)法对电沉积材料的电化学性能进行分析,考察其催化氧还原反应的活性,最后以合成的材料为阴极催化剂,构建微生物燃料电池系统,考察其在微生物燃料电池中的应用效果。结果表明,以电沉积二氧化锰为阴极催化剂的微生物燃料电池最大功率密度为975.6 mW/m~2,是以商业二氧化锰为阴极催化剂的电池的1.7倍;这表明作为一种经济、高效、环境友好的阴极氧还原催化剂,电沉积法制备的二氧化锰为实现阴极催化剂的低成本制备以及微生物燃料电池放大化推进提供了新的研究途径。     

Pt/TiO2纳米纤维的制备及其对甲醇的电催化氧化活性

采用静电纺丝技术结合还原浸渍法制备了Pt/TiO₂纳米纤维电催化剂, 通过X射线衍射(XRD)分析、扫描电镜(SEM)、透射电镜(TEM)和X射线能谱(EDS)等测试手段对样品的晶相、形貌、微结构和化学组成进行了表征. 测试结果表明, TiO₂纳米纤维为锐钛矿和金红石组成的混晶, Pt 纳米颗粒均匀地分布于TiO₂纳米纤维的表面, 且Pt 颗粒大小较均一, 平均粒径为4.0 nm, Pt/TiO₂纳米纤维中Pt 的质量分数约为20%. 采用三电极体系的循环伏安和计时电流电化学分析方法研究了样品在酸性溶液中对甲醇的电催化氧化活性, 结果表明, 与负载相同质量分数Pt 的Pt/P25 和商业Pt/C 催化剂相比较, Pt/TiO₂纳米纤维催化剂对甲醇呈现出较高的电催化氧化活性和更好的稳定性.     

酸处理石墨化碳载体对燃料电池催化剂性能的影响

通过1700 ℃高温处理XC-72CB得到石墨化碳黑(GCB), 并采用酸处理对GCB碳载体进行官能团修饰. 透射电子显微镜(TEM)、 X射线粉末衍射(XRD)和拉曼光谱的结果显示, 酸处理后GCB的石墨化程度增加; N₂吸附-脱附结果证明GCB比表面积减小, 微孔数量减少; 热重分析结果表明, GCB热稳定性增强; 红外光谱和拉曼光谱结果显示, GCB表面引入了含氧官能团, 并同时保持了GCB的有序化结构. 采用循环伏安(CV)法和线性扫描伏安(LSV)法测试了不同预处理后催化剂的电化学性能, 表明其电化学活性表面积(ECSA, 75.25 m²/g)和质量比活性(MA, 0.093 A/mg)均高于商业Pt/C(JM)催化剂. TEM结果表明, 使用经过浓硫酸和浓硝酸混合酸处理的GCB(简称OGCB)作为载体得到的Pt/OGCB平均粒径为2.28 nm, 略小于商业Pt/C(JM)催化剂(约2.5 nm); 经5000周电化学循环伏安测试后, Pt/OGCB的电化学活性表面积衰减17.3%, 质量比活性衰减29.5%, 而Pt/C(JM)的ECSA衰减达到25.1%, MA衰减达到42.5%.     

氮、硫共掺杂的碳负载的钴@碳化钴:一种高效的非贵金属氧还原电催化剂

Development of high-efficiency and low-cost electrocatalysts for large-scale oxygen reduction reaction (ORR) remains a challenge. In this study, we employed melamine, trithiocyanuric acid, and cobaltous nitrate to fabricate a novel ORR electrocatalyst with cobalt and cobalt carbide supported on carbon co-doped with nitrogen and sulfur (hereafter referred to as MTC-0.1-900) by two-step pyrolysis. The MTC-0.1-900 was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy, Brunauer-Emmett-Teller (BET) specific surface area analysis, and X-ray photoelectron spectroscopy (XPS). The electrochemical performance for ORR was investigated by cyclic voltammetry and linear sweep voltammetry in 0.1 mol·L^-1 KOH solutions. The results showed that the onset potential and half-wave potential of MTC-0.1-900 were 29 and 5 mV superior to the commercial Pt/C catalyst, respectively. After 12000 s operation at the potential of -0.3 V (vs Ag/AgCl), the current retention capacities of MTC-0.1-900 and Pt/C were 97.1% and 76.7%, respectively. MTC-0.1-900 also showed better methanol tolerance than Pt/C. These unique properties of MTC-0.1-900 provide us with an alternative for replacing or reducing the use of Pt catalyst in metal-air battery cathode materials.     

金属前驱体对质子交换膜燃料电池用PtCu/C催化剂性能的影响

采用乙二醇还原法,利用不同金属前驱体(CuSO_4/CuCl_2、K_2PtCl_4/H_2PtCl_6)制备了铂铜总质量分数为20%的四种PtCu/C催化剂,并通过透射电子显微镜(TEM)、X射线衍射(XRD)、循环伏安法(CV)和线性扫描伏安法(LSV)对催化剂进行物相结构表征及电化学性能测试。结果表明,以CuSO_4和K_2PtCl_4为前驱体组合制备出的PtCu/C催化剂性能最优。所制备的PtCu/C催化剂金属颗粒平均粒径为2.3nm,粒径范围窄,在碳载体上负载均匀;电化学活性面积(ECSA)达到73.0m2/gPt,质量比活性(MA)为126.65mA/mgPt,均优于商业Pt/C催化剂。     

Electrochemical performance of annealed cobalt-benzotriazole/CNTs catalysts towards the oxygen reduction reaction

One of the major limitations yet to the global implementation of polymer electrolyte membrane fuel cells (PEMFCs) is the cathode catalyst. The development of efficient platinum-free catalysts is the key issue to solve the problem of slow kinetics of the oxygen reduction reaction (ORR) and high cost. We report a promising catalyst for ORR prepared through the annealing treatment under inert conditions of the cobalt-benzotriazole (Co-BTA) complex supported on carbon nanotubes (CNTs). The N-rich benzotriazole precursor was chosen based on its ability to complex Co(II) ions and generate under annealing highly reactive radicals able to tune the physicochemical properties of CNTs. X-Ray photoelectron spectroscopy (XPS) was used to follow the surface structure changes and highlight the active electrocatalytic sites towards the ORR. To achieve further evaluation of the catalysts in acidic medium, voltamperometry, rotating disk electrode (RDE), rotating ring-disk electrode (RRDE) and half-cell measurements were performed. The resulting catalysts (Co/N/CNTs) all show catalytic activity towards the ORR, the most active one resulting from annealing at 700 °C. The overall electron transfer number for the catalyzed ORR was determined to be ～3.7 with no change upon the catalyst loading, suggesting that the ORR was dominated by a 4e(-) transfer process. The results indicate a promising alternative cathode catalyst for ORR in fuel cells, although its performance is still lower (overpotential around 110 mV evaluated by RDE and RRDE) than the reference Pt/C catalyst.     

Pt/Au/Fe3O4的制备及其电化学性能

以制得的纳米Fe₃O₄颗粒作为载体,用还原法将还原出的Au与Pt分别负载到Fe₃O₄颗粒表面,制得纳米Pt/Au/Fe₃O₄复合材料。对Pt/Au/Fe₃O₄进行紫外可见光吸收光谱、透射电子显微镜、X射线衍射及光电子能谱等物理表征,结果表明,Au与Pt均匀地沉积到了Fe₃O₄纳米颗粒表面。对纳米Pt/Au/Fe₃O₄复合材料进行循环伏安扫描,当H₂PtCl₆的加入量达到8 mL时,Pt/Au/Fe₃O₄催化性能最佳;正扫电流峰i_p与扫描速率的平方根v^1/2线性相关,Pt/Au/Fe₃O₄催化氧化甲醇的过程受扩散控制;对催化剂进行201次循环伏安扫描,催化剂仍然能保持较好的催化性能且稳定性良好。因此,所合成催化剂Pt/Au/Fe₃O₄是一种具有良好化学稳定性的阳极催化剂材料。