等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

Ag/Ag_3PO_4/g-C_3N_4复合光催化剂的合成与再生及其可见光下的光催化性能(英文)

研究了用离子交换沉淀法制备的Ag/Ag3PO4/g-C3N4的可见光光催化性能及再生方法.通过X射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、紫外-可见(UV-Vis)吸收光谱及X射线光电子能谱(XPS)对其进行了结构特性分析.XRD结果显示再生后催化剂的结构未发生改变.FESEM及UV-Vis分析结果说明催化剂由Ag3PO4与g-C3N4复合而成.XPS分析结果表明催化剂表面出现少量的银单质.利用可见光(λ420nm)照射下的苯酚降解实验评价了样品的光催化活性,并通过活性物种及能带结构的分析对催化剂的光催化机理进行了推测.研究表明,Ag/Ag3PO4/g-C3N4的光催化活性明显高于纯Ag3PO4及纯g-C3N4,主要原因归结为单质银、Ag3PO4及g-C3N4的协同效应.经过氧化氢和磷酸氢铵钠(NaNH4HPO4)的再生可完全恢复催化剂的活性,这表明该绿色环保的再生方法可实现Ag/Ag3PO4/g-C3N4催化剂在环境中的实际应用.     

氨氛围热处理g-C_3N_4控制N空位浓度提高光催化制氢性能

热处理氧化石墨相氮化碳(g-C_3N_4)材料产生氮缺陷、提升其光催化制氢性能的研究备受关注,但其N空位浓度高且不可控、一定程度破坏g-C_3N_4晶体结构,降低g-C_3N_4的结晶度,导致光生电子-空穴对复合率高,致使其光催化制氢效率较低。基于上述问题,本研究以二氰二胺为前驱体制备了g-C_3N_4,与不同含量的尿素混合,在空气中加热快速热处理,通过X-射线衍射仪(XRD)、扫描电子显微镜(SEM)等测试手段,对其物相组成、微观形貌、光学吸收等进行了表征,在可见光条件下对样品进行了光催化制氢性能测试,研究了尿素的加入对热处理后g-C_3N_4材料的N空位浓度、结晶度及光催化制氢性能的影响。研究表明,尿素的加入降低了N空位的浓度,且提升了其结晶度。在优化的尿素添加量下,g-C_3N_4的可见光光催化制氢速率为6.5μmol·h-1,是没有添加尿素处理的样品的3倍。该研究结果表明,利用尿素原位分解产生的NH_3,可以抑制g-C_3N_4热处理过程中氮原子的氧化程度、实现调控N空位浓度,同时提高了结晶度,最终提升了其光催化制氢性能。     

g-C_3N_4/BiOBr异质结光催化剂的制备与可见光催化活性

以三聚氰胺作为合成g-C_3N_4纳米片的前躯体,以Bi(NO3)3·5H2O和KBr作为合成BiOBr的原料,采用水热法构建g-C_3N_4/Bi OBr二维异质结可见光催化剂,有效的晶面复合和合适的能带组合有助于增强g-C_3N_4和BiOBr的可见光催化活性。利用X射线衍射(XRD)、透射电镜(TEM)、X射线光电子能谱(XPS)、光致发光光谱(PL)和紫外-可见漫反射光谱(UVvis DRS)等方法表征其结构、光学性质以及组成结构。在可见光(λ420 nm)下以光催化降解RhB来评价合成催化剂的光催化活性,结果表明,g-C_3N_4/BiOBr光催化降解罗丹明B(Rh B)的效率高于单体g-C_3N_4和BiOBr,并对g-C_3N_4/BiOBr增强可见光催化RhB机理进行解释。     

g-C3N4表面改性及其光催化制H2与CO2还原研究进展

Solar energy is the largest renewable energy source in the world and the primary energy source of wind energy, tidal energy, biomass energy, and fossil fuel. Photocatalysis technology is a sunlight-driven chemical reaction process on the surface of photocatalysts that can generate H₂ from water, decompose organic contaminants, and reduce CO₂ into organic fuels. As a metal-free polymeric material, graphite-like carbon nitride (g-C₃N₄) has attracted significant attention because of its special band structure, easy fabrication, and low costs. However, some bottlenecks still limit its photocatalytic performance. To date, numerous strategies have been employed to optimize the photoelectric properties of g-C₃N₄, such as element doping, functional group modification, and construction of heterojunctions. Remarkably, these modification strategies are strongly associated with the surface behavior of g-C₃N₄, which plays a key role in efficient photocatalytic performance. In this review, we endeavor to provide a comprehensive summary of g-C₃N₄-based photocatalysts prepared through typical surface modification strategies (surface functionalization and construction of heterojunctions) and elaborate their special light-excitation and response mechanism, photo-generated carrier transfer route, and surface catalytic reaction in detail under visible-light irradiation. Moreover, the potential applications of the surface-modified g-C₃N₄-based photocatalysts for photocatalytic H₂ generation and reduction of CO₂ into fuels are summarized. Finally, based on the current research, the key challenges that should be further studied and overcome are highlighted. The following are the objectives that future studies need to focus on: (1) Although considerable effort has been made to develop a surface modification strategy for g-C₃N₄, its photocatalytic efficiency is still too low to meet industrial application standards. The currently obtained solar-to‑hydrogen (STH) conversion efficiency of g-C₃N₄ for H₂ generation is approximately 2%, which is considerably lower than the commercial standards of 10%. Thus, the regulation of the surface/textural properties and electronic band structure of g-C₃N₄ should be further elucidated to improve its photocatalytic performance. (2) Significant challenges remain in the design and construction of g-C₃N₄-based S-scheme heterojunction photocatalysts by facile, low-cost, and reliable methods. To overcome the limitations of conventional heterojunctions thoroughly, a promising S-scheme heterojunction photocatalytic system was recently reported. The study further clarifies the charge transfer route and mechanism during the catalytic process. Thus, the rational design and synthesis of g-C₃N₄-based S-scheme heterojunctions will attract extensive scientific interest in the next few years in this field. (3) First-principle calculation is an effective strategy to study the optical, electrical, magnetic, and other physicochemical properties of surface strategy modified g-C₃N₄, providing important information to reveal the charge transfer path and intrinsic catalytic mechanism. As a result, density functional theory (DFT) computation will be paid increasing attention and widely applied in surface-modified g-C₃N₄-based photocatalysts.     

Ni2P-NiS双助剂促进g-C3N4光催化产氢动力学

本文通过简单的一步水热法得到Ni₂P-NiS双助催化剂,之后采用溶剂蒸发法将Ni₂P-NiS与g-C₃N₄纳米片结合构建获得无贵金属的Ni₂P-NiS/g-C₃N₄异质结。研究结果表明,优化后的复合材料具有良好的光催化产氢活性,其产氢速率最高可到6892.7 μmol·g^-1·h^-1,分别为g-C₃N₄ (150 μmol·g^-1·h^-1)、15%NiS/g-C₃N₄ (914.5 μmol·g^-1·h^-1)和15%Ni₂P/g-C₃N₄ (1565.9 μmol·g^-1·h^-1)的46.1、7.5和4.4倍。这主要归因于Ni₂P-NiS相比Ni₂P和NiS单体具有更好的载流子转移能力,其与g-C₃N₄形成的肖特基势垒能有效促进光生载流子在二者界面上的分离,同时Ni₂P-NiS能进一步降低析氢过电势,进而显著增强了表面析氢反应动力学。本研究为开发稳定、高效的非贵金属产氢助剂提供了实验基础。     

多组分纳米纤维体系中载流子动力学的有效级联调制及其高效光催化产氢性能研究（英文）

利用半导体作为催化剂,将水光催化还原为H₂,为缓解全球能源危机以及环境污染问题提供了一种经济环保的途径。优化调控载流子动力学行为对提高半导体光催化分解水还原为绿色燃料-H₂的活性具有十分重要的意义。目前,基于半导体异质结效应或局域表面等离激元共振的敏化过程来设计和调控半导体基异质结构体系已成为调控载流子动力学行为的一种经典策略。然而,通过精细设计异质结构,合理耦合上述敏化过程,实现载流子动力学的级联调制,从而获得高效的光催化产H₂活性仍然任重道远。在本文中,我们通过原位氧化(g-C₃N₄的剥离和Ag₂S)和还原(Ag)反应,将等离激元Ag纳米颗粒(NPs)和两种不同的半导体Ag₂SNPs和g-C₃N₄纳米片(NSs)组装在电纺TiO₂纳米纤维(NFs)中,形成了一种新型四元异质组分纳米纤维(HNFs)体系。结合时间分辨光致发光光谱,3D时域有限差分模拟以及对照实验,我们...     

Enhanced Visible-light Photocatalytic Activity of g-C3N4/Nitrogen-doped Graphene Quantum Dots/TiO2 Ternary Heterojunctions for Ciprofloxacin Degradation with Narrow Band Gap and High Charge Carrier Mobility

Limited visible-light absorption and high recombination rate of photogenerated charges are two main drawbacks in g-C₃N₄-based photocatalysts. To solve these problems, g-C₃N₄/nitrogen-doped graphene quantum dots (NGQDs)/TiO₂ ternary heterojunctions were facilely prepared via a one-step calcining method. The morphology, structure, optical and electrochemical properties of g-C₃N₄/NGQDs/TiO₂ were characterized and explored. The optimal g-C₃N₄/NGQDs/TiO₂ composite exhibits enhanced photocatalytic degradation performance of ciprofloxacin (CIP) compared with the as-prepared g-C₃N₄, TiO₂(P25) and g-C₃N₄/TiO₂ heterojunction under visible light irradiation. The apparent rate constant of the composite is around 6.43, 4.03 and 2.30 times higher than those of g-C₃N₄, TiO₂ and g-C₃N₄/TiO₂, respectively. The enhanced photocatalytic efficiency should be mainly attributed to the improvement of light absorption and charge separation and transfer efficiency, originating from the narrow band gap and high charge carrier mobility. The active species trapping experiments results showed that the h⁺ and ^·O₂^- were the main active species in the degradation process. A possible photocatalytic reaction mechanism of the g-C₃N₄/NGQDs/TiO₂ composite for the enhanced degradation of CIP under visible light irradiation was also proposed.     

Pt-M (M = Co,Ni, Fe)/g-C3N4复合材料构建及其高效光解水制氢性能

Platinum (Pt) is recognized as an excellent cocatalyst which not only suppresses the charge carrier recombination of the photocatalyst but also reduces the overpotential for photocatalytic H₂ generation. Albeit of its good performance, the high cost and low abundance restricted the utilization of Pt in large-scale photocatalytic H₂ generation. Pt based transition metal alloys are demonstrated to reveal enhanced activities towards various catalytic reactions, suggesting the possibility to substitute Pt as the cocatalyst. In the present work, Pt was partially substituted with Co, Ni, and Fe and Pt-M (M = Co, Ni, and Fe)/g-C₃N₄ composites were constructed through co-reduction of H₂PtCl₆ and transition metal salts by the reductant of ethylene glycol. The crystal structure and valence states were measured by X-ray diffractometer (XRD) and X-ray photoelectron spectrometer (XPS), respectively. The higher degree of XRD peaks and larger binding energies for Pt 4f_5/2 and Pt 4f_7/2 after incorporating Co²⁺ ions indicated that Co was successfully introduced into the lattice of Pt and Pt-Co bimetallic alloys was attained through the solvothermal treatment. The morphology was subsequently observed by transmission electron microscope (TEM), which showed a good dispersion of Pt-Co nanoparticles on the surface of g-C₃N₄. Meanwhile, the shrinkage of lattice fringe after introducing cobalt salt further confirmed the presence of Pt-Co bimetallic alloys. The UV-Vis absorption spectra of g-C₃N₄ and Pt, Pt-Co deposited g-C₃N₄ were subsequently performed. It was found that the absorption edges were all consistent for all three samples as anticipated, implying that the band gap energy was maintained after hybridizing with Pt or Pt-Co alloys. Furthermore, the photocatalytic H₂ generation was carried out over the as-prepared composites with triethanolamine (TEOA) as sacrificial reagent. Under visible-light illumination, the1% (w) Pt_2.5M/g-C₃N₄ (M = Co, Fe, Ni) composites all exhibited higher or comparable activity towards photocatalytic H₂ generation when compared to 1% (w) Pt loaded counterpart. In addition, the atomic ratios of Pt/Co and the loading amount of Pt-Co cocatalyst were modified to optimize the photocatalytic performance, among which, 1% (w) Pt_2.5Co/g-C₃N₄ composite revealed the highest activity with a 1.6-time enhancement. Electrochemical impedance spectra (EIS) and photoluminescence (PL) spectra indicated that the enhancement might be attributed to improved charge transfer from g-C₃N₄ to Pt_2.5Co cocatalyst and inhibited charge carrier recombination in the presence of Pt_2.5Co cocatalyst. Therefore, the present study demonstrates the great potential to partially replace Pt with low-cost and abundant transition metals and to fabricate Pt based bimetallic alloys as promising cocatalysts for highly efficient photocatalytic H₂ generation.     

类石墨烯C3N4纳米片光催化分解水制氢中的量子限域效应

从层状化合物获得的纳米片是一类新型纳米结构材料,这种二维各向异性的纳米甚至亚纳米级的材料具有独特的物理化学性能,其中最好的一个例证就是从石墨烯C₃N₄到石墨烯C₃N₄纳米片的转变。通过高温氧化热刻蚀方法将体相g-C₃N₄剥离成g-C₃N₄纳米片,应用于染料敏化可见光分解水产氢,表现出了较体相g-C₃N₄高于2.6倍的产氢速率。通过X射线衍射（XRD）、傅里叶变换红外（FTIR）光谱、扫描电子显微镜（SEM）、Brunauer-Emmett-Teller（BET）、荧光光谱和光电化学等表征研究了g-C₃N₄纳米片的结构及曙红（EY）和g-C₃N₄纳米片之间的电子迁移过程。热剥离后的g-C₃N₄纳米片具有较高的比表面积,不仅可以更为有效地吸附染料分子,还因其量子限域效应大大增强了光生电荷的分离效率和电子转移效率,改善了电子沿平面方向的传输能力以及光生载流子的寿命,从而显著提高g-C₃N₄纳米片的光催化产氢活性。     

原位光沉积制备Z型α-Fe2O3/g-C3N4异质结及其可见光驱动光解水产氢性能

采用原位光沉积-煅烧法制得了Z型α-Fe₂O₃/g-C₃N₄异质结复合光催化剂。分别采用透射电子显微镜、X射线衍射、X射线光电子能谱、紫外可见漫反射光谱、荧光光谱以及电化学测试对样品进行了表征,并考察了可见光下光解水产氢活性。结果表明:当α-Fe₂O₃的负载量为2.9%时,α-Fe₂O₃/g-C₃N₄复合光催化剂具有最优的产氢催化活性,产氢速率高达1841.9μmol·g^-1·h^-1,约为g-C₃N₄的3.3倍。光催化性能的提高主要归因于3方面:(1)高温煅烧过程中α-Fe₂O₃的形成,有效促进了氮化碳片层的热剥离,增大了比表面积,从而为光催化反应提供了更多反应活性位;(2)超细α-Fe₂O₃颗粒(5~8 nm)高度均匀地分散在g-C₃N₄表面,并且与其紧密结合,形成了高质量的Z型异质结;(3)Z型异质结不仅有效抑制地了光生载流子的复合,同时极大地保留了g-C₃N₄导带电子的强还原性和α-Fe₂O₃价带空穴的强氧化性。