Visualization of 2-μm radiation by BiF<Subscript>3</Subscript>:Ho<Superscript>3+</Superscript> and BiF<Subscript>3</Subscript>:Ho<Superscript>3+</Superscript>/Yb<Superscript>3+</Superscript> ceramics

A series of ceramic samples of the compositions BiF₃:1%Ho³⁺, BiF₃:4%Ho³⁺, BiF₃:1%Ho³⁺ + 1%Yb³⁺, and BiF₃:1%Ho³⁺ + 3%Yb³⁺ is synthesized and the conversion of Tm:YLF laser radiation (λ = 1908 nm) is studied. The luminescence spectra exhibit bands in the regions of 490, 545, and 650 nm. The kinetic measurements of the afterglow of the green and red bands show that the population of the ⁵S₂ and ⁵F₄ states in the BiF₃:1%Ho³⁺ samples occurs due to successive absorption of excitation photons, while the ⁵F₅ level of Ho³⁺ is populated due to the ion–ion interaction. Codoping with Yb³⁺ leads to a decrease in the visualization threshold power density to 2 W/cm².     

Visible upconversion and infrared luminescence investigations of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> powders doped with Er<Superscript>3+</Superscript>, Yb<Superscript>3+</Superscript> and Zn<Superscript>2+</Superscript> ions

Alumina (Al₂O₃) powders doped with Er³⁺, Yb³⁺ and Zn²⁺ ions have been prepared by a low-temperature combustion synthesis technique. The phase purity and crystalline structure of the combustion products are confirmed by powder X-ray diffraction. An efficient frequency upconversion in the visible region and the emission in the infrared (IR) region respectively corresponding to the ²H_11/2, ⁴S_3/2→⁴I_15/2, ⁴F_9/2→⁴I_15/2 and ⁴I_13/2→⁴I_15/2 transitions upon direct excitation with a CW laser lasing at ∼980 nm are discussed. The enhancement observed in the intensity of the upconversion emission bands in the visible region and the emission band in the IR region due to the presence of Yb³⁺ and Zn²⁺ in Er³⁺:Al₂O₃ powders is reported and explained in detail.     

O<Subscript>2</Subscript> photodesorption from AuO<Stack><Subscript>2</Subscript><Superscript>−</Superscript></Stack> and Au<Subscript>2</Subscript>O<Stack><Subscript>2</Subscript><Superscript>−</Superscript></Stack>

Using time-resolved photoelectron spectroscopy, the decay channels of AuO₂⁻ and Au₂O₂⁻ following photoexcitation with 3.1-eV photons have been studied. For AuO₂⁻, a state with a rather long lifetime of 30 ps has been identified. Its decay path could not be determined but photodesorption can be excluded. For Au₂O₂⁻, the spectra indicate O₂ desorption after 3.1-eV photoexcitation on a time scale of 1 ps. While comparing these results on Au _n O₂⁻ with analogous data on Ag _n O₂⁻ clusters, a discernible pattern emerges: for dissociatively bound O₂(AuO₂⁻, Ag₃O₂⁻), there are long-living excited states which do not decay by oxygen desorption, while for molecular chemisorption (Au₂O₂⁻, Ag₂O₂⁻, Ag₄O₂⁻, Ag₈O₂⁻), the 3.1-eV photoexcitation triggers fast O₂ desorption with a high quantum yield.     

Hydrothermal synthesis,characterization, and luminescence of Ca<Subscript>2</Subscript>B<Subscript>2</Subscript>O<Subscript>5</Subscript>:RE (RE = Eu<Superscript>3+</Superscript>, Tb<Superscript>3+</Superscript>, Dy<Superscript>3+</Superscript>) nanofibers

Ca₂B₂O₅:RE (RE = Eu³⁺, Tb³⁺, Dy³⁺) nanofibers were synthesized by the hydrothermal reaction method. The structural refinement was conducted on the base of the X-ray powder diffraction (XRD) measurements. The surface properties of the Ca₂B₂O₅:RE (RE = Eu³⁺, Tb³⁺, Dy³⁺) nanofibers were investigated by the measurements such as the scanning electron microscope (SEM), transmission electron microscope (TEM), and the energy dispersive spectrum (EDS). The nanofiber has a diameter of about 100 nm and a length of several micrometers. The luminescence properties such as photoluminescence excitation (PLE) and emission spectra (PL), decay lifetime, color coordinates, and the absolute internal quantum efficiency (QE) were reported. Ca₂B₂O₅:Eu³⁺ nanofibers show the red luminescence with CIE coordinates of (x = 0.41, y = 0.51) and the luminescence lifetime of 0.63 ms. The luminescence of Ca₂B₂O₅:Tb³⁺ nanofibers is green color (x = 0.29, y = 0.53) with the lifetime of 2.13 ms. However, Dy³⁺-doped Ca₂B₂O₅ nanofibers present a single-phase white-color phosphor with the fluorescence decay of 3.05 ms. Upon near-UV excitation, the absolute quantum efficiency is measured to be 65, 35, and 37 % for Eu³⁺-, Tb³⁺-, Dy³⁺-doped Ca₂B₂O₅ nanofibers, respectively. It is suggested that Ca₂B₂O₅:RE (RE = Eu³⁺, Tb³⁺, Dy³⁺) nanofibers could be an efficient phosphor for lighting and display.     

Calix[4]arene Based Dual Fluorescent Sensor for Al<Superscript>3+</Superscript> and S<Subscript>2</Subscript>O<Subscript>7</Subscript><Superscript>2−</Superscript>

Specific functionalized calix[4]arene based fluorescent chemosensor was synthesized for cations and anions binding efficiency examination. Receptor C4MA displayed strong affinity for Al³⁺and S₂O₇ ^2? with enhanced fluorescence intensity. The selective response of C4MA was investigated in the presence of different co-existing competing ions. The limit of detection (LOD) of Al³⁺and S₂O₇ ^2? was calculated as 2.8?×?10^?6 M and 2.6?×?10^?7 M respectively. Sensor C4MA forms (1:1) stoichiometric complex with both Al³⁺ and S₂O₇ ^2? and their binding constants were calculated as 12.1?×?10⁴ and 8.3?×?10³ respectively. Complexes were also characterized through FT-IR spectroscopy.

Open image in new window

Graphical Abstract ?

     

Spectroscopic analysis of Pr<Superscript>3+</Superscript> crystal-field transitions in YAl<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript>

Yttrium aluminium borate single crystals, doped with 1 and 4 mol% of Pr³⁺, were analyzed in the wave number range 500–25000 cm⁻¹ and temperature range 9–300 K by means of high-resolution Fourier transform spectroscopy. In spite of the complex spectra, exhibiting broad and split lines, the energy level scheme was obtained for several excited manifolds. The careful analysis of the spectra as a function of the temperature allowed us to identify most of the sublevels of the ground manifold. The thermally induced line shift, well described by a single-phonon coupling model, could be exploited to provide information about the energy of the phonons involved. The orientation of the dielectric ellipsoid and of the dipole moments associated to a few transitions was also determined from linear dichroism measurements. The experimental data were fitted in the framework of the crystal-field theory, but the agreement was not satisfactory, as already reported for Pr³⁺ ion in other matrices. Additional discrepancies came from the dichroic spectra analysis and the line splitting, possibly associated to hyperfine interaction. Some causes which might be responsible for the difficulties encountered in the Pr³⁺ ion theoretical modelling are discussed.     

Hyperfine Interactions in Pb<Superscript>3+</Superscript>F<Stack><Subscript>8</Subscript><Superscript>−</Superscript></Stack>F<Stack><Subscript>a</Subscript><Superscript>−</Superscript></Stack> clusters in fluorite crystals

The parameters of hyperfine interactions in Pb³⁺F ₈ ^? F _a ^? tetragonal clusters of MeF₂ crystals (Me=Ca, Sr, Ba) are interpreted. The contributions of the spin polarization to the parameters of the proper hyperfine interaction and additional (ligand) hyperfine interactions are calculated in the approximation of weak binding between a charge-compensating ion F _a ^? and a cubic fragment in the tetragonal cluster. It is demonstrated that correct inclusion of the contributions from the spin polarization to the ligand isotropic hyperfine interaction for the F _a ^? ion leads to anomalously large parameters of this interaction for MeF₂ crystals. These results are in agreement with experimental data.     

Potential energy of <Superscript>∞</Superscript>H<Stack><Subscript>2</Subscript><Superscript>-</Superscript></Stack>(<Superscript>2</Superscript>∑<Stack><Subscript>u</Subscript><Superscript>+</Superscript></Stack> in the bound-state region

An accurate calculation of the lowest negative electronic state of H ₂ ^- (fixed nuclei) is reported using the CCSD(T) method and doubly augmented cc-pv5z basis set. Comparison has been made with the reference data by Senekowitsch et al. [Chem. Phys. Lett. 111 (1984) 211]. Owing to larger size of the basisset and inclusion of triple excitations, no vertical shift in this work is necessary to reproduce the asymptotics of H + H ^-. In addition, the effect of basis-set truncation is estimated, based on the complete-basis-set extrapolation method. The contribution of correlated electron-proton motion to the electron-energy curve for H₂ ^– dynamics is pointed out.Dedicated to Prof. Jií Horáek on the occasion of his 60th birthday.     

Concentration quenching of Eu<Superscript>2+</Superscript> in a novel blue–green emitting phosphor: Ba<Subscript>2</Subscript>ZnSi<Subscript>2</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>2+</Superscript>

A novel blue–green emitting phosphor Ba₂ZnSi₂O₇: Eu²⁺ was prepared by a combustion synthesis (CS) method. An efficient green emission under conditions ranging from ultraviolet to visible light was observed. The emission spectrum shows a single intensive band centered at 503 nm, which corresponds to the 4f ⁶5d ¹→4f ⁷ transition of Eu²⁺. The excitation spectrum is a broad band extending from 260 to 465 nm, which matches the emission of ultraviolet light-emitting diodes (UV-LEDs). The critical quenching concentration of Eu²⁺ in Ba₂ZnSi₂O₇:Eu²⁺ phosphor is about 0.05 mol. The corresponding concentration quenching mechanism is verified to be a dipole–dipole interaction. The value of the critical transfer distance is calculated as 19 Å, which is in good agreement with the value (20 Å) derived from the experimental data.     

110 W ceramic Nd<Superscript>3+</Superscript> : Y<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript> laser

A high-power, continuous-wave 0.6% Nd³⁺-doped ceramic Y₃Al₅O₁₂ (Nd:YAG) laser has been developed. 110 W laser output at 1064 nm was obtained, with a slope efficiency of about 41%. The M² factor was found to be around 6. The laser performance of the ceramic laser material was found to compare favorably with that obtained with single crystal Nd:YAG. PACS 42.55.-f; 42.55.Xi; 42.70.Hj     

Electron paramagnetic resonance of Er<Superscript>3+</Superscript> ions in a polycrystalline α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The EPR spectra of rare-earth Er³⁺ ions in a polycrystalline corundum α-Al₂O₃ synthesized by the sol-gel technology were revealed. It is shown that the EPR spectra belong to the Er³⁺ ions in the ground state corresponding to the lower Stark sublevel of the ⁴ I _15/2 term and can be described by the spin Hamiltonian of axial symmetry with an effective spin S = 1/2 and the g tensor with components g _‖ = 12.176 and g _⊥ = 4.14. The average value of the g tensor (〈g〉 = 6.82) corresponds to the Γ₇ state in a cubic field. Erbium is assumed to substitute for aluminum in the Al₂O₃ corundum crystal. The local symmetry C ₃ of the Al³⁺ ion remains despite the pronounced expansion of the lattice around the Er³⁺ ion.     

Luminescence properties of Nd<Superscript>3+</Superscript>-doped Y<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles in organic media

Nd³⁺-doped yttrium oxide nanoparticles (Y₂O₃:Nd) with cubic phase were obtained successfully by a glycine-nitrate solution combustion method. The results of Fourier transform infrared spectra (FTIR) showed that the –OH groups residing on the nanoparticles surfaces were reduced effectively by modifying with capping agent. The modified Y₂O₃:Nd nanoparticles displayed good monodispersity and excellent luminescence in N,N-dimethylformamide (DMF) solvent. Some optical parameters were calculated by Judd–Ofelt analysis based on absorption and fluorescence spectra. A relative large stimulated emission cross section, 1.7×10⁻²⁰ cm², of the ⁴F_3/2→⁴I_11/2 transition was calculated. Theses results show that the modified Y₂O₃:Nd nanoparticles display good luminescence behavior in organic media.     

EIT Ground State Cooling Scheme of <Superscript>171</Superscript>Yb<Superscript>+</Superscript> Based on the <Superscript>2</Superscript>S<Subscript>1/2</Subscript>→<Superscript>2</Superscript>P<Subscript>1/2</Subscript> Cooling Transition

We propose a method for EIT ground state cooling of ¹⁷¹Yb+ ion, which involves three light fields with detuning on a MHz scale. The steady-state mean vibrational quantum number is calculated to be less than 0.005. Efficient cooling is achievable in a motional-mode frequency range of 2π · (1.5 ± 0.5 MHz).     

Odd autoionizing 2p<Subscript>1/2</Subscript><Superscript>5</Superscript>n(s<Superscript>′</Superscript>/d<Superscript>′</Superscript>) resonances of Ne excited from the 2p<Superscript>5</Superscript>3p[K]<Subscript>J</Subscript> states

Absolute photoionization cross sections for Ne atoms in the excited levels (Paschen notation ) were calculated at near threshold energies within the configuration interaction Pauli-Fock approach including core polarization. The computed spectra and the lineshape parameters of the odd parity 2p_1/2 ⁵ns^′/d^′ autoionizing resonances are found to be in good agreement with high resolution laser spectroscopic results. Guided by the theoretical results, improved analyses of the measured spectra by superimposed Fano-type profiles were achieved. Theoretical predictions are presented for resonances which have not yet been studied experimentally. In addition, we report the absolute partial photoionization cross sections for the ²P_3/2 and ²P_1/2 channel at photoelectron energies up to 7 eV. Except for the highest lying 2p₁(¹S₀) level, these cross sections monotonically decrease with energy (as reported earlier in single-electron calculations for the Ne(2p⁵3p) configuration) with branching ratios which essentially reflect the core composition of the 2p_x levels. For the 2p₁ level the resonance structure and the partial cross sections are strongly influenced by a Cooper-Seaton minimum in the d_3/2 ^′ channel,located just above the ²P_1/2 ionization limit.     

Optimizing after-glow luminescent parameters of Sr<Subscript>4</Subscript>Al<Subscript>14</Subscript>O<Subscript>25</Subscript>:Eu<Superscript>2+</Superscript>, Dy<Superscript>3+</Superscript>, by sol–gel method and combustion process

Strontium aluminates are viewed as a promising persistent luminescent materials. There are many researches on strontium aluminates, including SrAl₂O₄, Sr₄Al₁₄O₂₅. Between these two phases, Sr₄Al₁₄O₂₅ shows much better properties than SrAl₂O₄. The traditional way to synthesize Sr₄Al₁₄O₂₅ is the solid state reaction. However, it exists few problems, especially non-homogeneous product. As a result, there are two methods chosen to make homogeneous precursor. One is sol–gel method, the other is combustion with Urea as a fuel. Boric acid is added as a flux in both method. In this study, combustion process is found to be a better way for synthesizing Sr₄Al₁₄O₂₅. We change the temperature, synthetic method. The samples are finely grinded and used for XRD analysis, photoluminescence measurement, and after-glow decay curve to figure out the optimizing luminescent parameters.     

<Superscript>57</Superscript>Fe emission Mössbauer spectroscopy following dilute implantation of <Superscript>57</Superscript>Mn into In <Subscript>2</Subscript>O<Subscript>3</Subscript>

Emission Mössbauer spectroscopy has been utilised to characterize dilute ⁵⁷Fe impurities in In ₂O₃ following implantation of ⁵⁷Mn (T _1/2 = 1.5 min.) at the ISOLDE facility at CERN. From stoichiometry considerations, one would expect Fe to adopt the valence state 3 + , substituting In ³⁺, however the spectra are dominated by spectral lines due to paramagnetic Fe²⁺. Using first principle calculations in the framework of density functional theory (DFT), the density of states of dilute Fe and the hyperfine parameters have been determined. The hybridization between the 3d-band of Fe and the 2p band of oxygen induces a spin-polarized hole on the O site close to the Fe site, which is found to be the cause of the Fe²⁺ state in In ₂O₃. Comparison of experimental data to calculated hyperfine parameters suggests that Fe predominantly enters the 8b site rather than the 24d site of the cation site in the Bixbyite structure of In ₂O₃. A gradual transition from an amorphous to a crystalline state is observed with increasing implantation/annealing temperature.     

Frequency upconversion properties of Ag: TeO<Subscript>2</Subscript>–ZnO nanocomposites codoped with Yb<Superscript>3+</Superscript> and Tm<Superscript>3+</Superscript> ions

Yb³⁺–Tm³⁺ codoped tellurite glasses containing silver nanoparticles (NPs) were synthesized and characterized using transmission electron microscopy and optical techniques. The samples’ composition and the nucleation of NPs were investigated using electron diffraction and energy dispersive spectroscopy. For the optical experiments, the samples were excited using a diode laser operating at 980 nm, in resonance with the Yb³⁺ transition ²F_7/2→²F_5/2. Photoluminescence (PL) bands corresponding to Tm³⁺ transitions were observed at 480, 650, and 800 nm due to the Yb³⁺→ Tm³⁺ energy transfer. PL enhancement was achieved by heat-treatment of the samples at 325°C during different time intervals. The growth of the PL bands correlates with the increase of the silver NPs concentration. The relevant mechanisms contributing for the PL characteristics are discussed.     

Visible up-conversion and NIR luminescence studies of LiAl<Subscript>5</Subscript>O<Subscript>8</Subscript>:Er phosphor co-doped with Yb<Superscript>3+</Superscript> and Zn<Superscript>2+</Superscript>

The frequency up-conversion, an efficient laser emission and amplification in Er³⁺:LiAl₅O₈ phosphors co-doped with Yb³⁺ and Zn²⁺ phosphor powders in the 520–560, 640–680 nm regions and at ∼1.5 μm, respectively, have been reported. The emission corresponds to the ²H_11/2, ⁴S_3/2→⁴I_15/2, ⁴F_9/2→⁴I_15/2 and ⁴I_13/2→⁴I_15/2 transitions upon direct excitation into the intermediated ⁴I_11/2 level using ∼980 nm radiation from a CW laser. Possible mechanisms involved for the up-conversion processes based on the energy level matching scheme, the pump-power dependence and the dynamical behaviour have been discussed. The effect of the addition of Yb³⁺ and Zn²⁺ for the amplification in the 1.5 μm eye-safe telecommunication window has been elaborated and characterized in detail.     

Anti-Stokes Luminescence in LiYF<Subscript>4</Subscript>:Ho<Superscript>3+</Superscript>, Yb<Superscript>3+</Superscript> Ceramics Excited at 1.93 μm

Conversion of IR radiation of a Tm:YAP laser with a wavelength of 1930 nm into visible light by ceramics of composition LiY_(1–x–y) Ho _x Yb _y , where х = 1–5 mol % and y = 0–15 mol %, is demonstrated. It is shown that the threshold power density of IR light visualization decreases with increasing concentration of Ho³⁺ ions, while additional doping of ceramic samples with Yb³⁺ ions changes the anti-Stokes luminescence spectrum. The threshold power density of visualization of the Tm:YAP laser radiation decreases with increasing concentration of holmium ions and is I_thr ≈ 0.8 W cm^–2 in the samples of composition LiYF₄:5%Ho³⁺–15%Yb³⁺.     

Synthesis and electrochemical performance of amorphous nickel hydroxide codoped with Fe<Superscript>3+</Superscript> and CO<Stack><Subscript>3</Subscript><Superscript>2−</Superscript></Stack>

Amorphous nickel hydroxide codoped with Fe³⁺ and CO₃²⁻ was synthesized by micro-emulsion precipitation method combined with rapid freezing technique. The microstructure and composition of the sample were characterized by X-ray diffraction and IR analysis. The electrochemical performance of the sample was analyzed by cyclic voltammetry, electrochemical impedance spectroscopy, and charge–discharge tests. The results showed that the Fe³⁺ and CO₃²⁻ codoping enhances the amorphous feature of the prepared nickel hydroxide. Moreover, the Fe³⁺ and CO₃²⁻ codoping could increase the specific capacity and improve the electrochemical reversibility of the amorphous nickel hydroxide electrode.