Fabrication and Characterization of a Thin-Layer Electrochemical Flow Cell and Its Application for Flow Analysis

The design and fabrication of a home-made thin-layer electrochemical flow cell are reported. The performance and electrochemical characteristics of thin-layer cells are evaluated in terms of flow rate and channel thickness. The adaptability of the flow cell for amperometric and electrochemiluminescence measurements is demonstrated. Also, a flow injection method comprising electrochemical generation followed by spectrophotometric detection is proposed for determination of bromide using the fabricated cell. The influence of chemical, electrochemical, and flow parameters on the absorbance and current signals are investigated, and under optimized conditions, the analytical features of the proposed method with respect to bromide detection are evaluated.     

Flow injection analysis-flame atomic absorption spectrometry system for indirect determination of cyanide using cadmium carbonate as a new solid-phase reactor

A new and simple flow injection system procedure has been developed for the indirect determination of cyanide. The method is based on insertion of aqueous cyanide solutions into an on-line cadmium carbonate packed column (25% m/m suspended on silica gel beads) and a sodium hydroxide with pH 10 is used as the carrier stream. The eluent containing the analyte as cadmiumcyanide complexes, produced from reaction between cadmium carbonate and cyanide, measured by flame atomic absorption spectrometry. The absorbance is proportional to the concentration of cyanide in the sample. The linear range of the system is up to 15 mg L⁻¹ with a detection limit 0.2 mg L⁻¹ and sampling rate 72 h⁻¹. The method is suitable for determination of cyanide in industrial waste waters with a relative standard deviation better than 1.22%.     

Design of an optical sensor for indirect determination of isoniazid

The characterization of an optical sensor membrane is described for indirect determination of isoniazid. The sensing membrane was consisted of immobilized 3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine (PDT) on a triacetylcellulose membrane. The procedure is based on the reaction of Fe(III) with isoniazid in the presence of PDT. Fe(III) is reduced by isoniazid to Fe(II) which forms a complex with PDT. The complex shows an absorption maximum at 558nm. By measuring the absorbance of the complex at this wavelength, isoniazid can be determined in the range of 0.62-6.15mugmL(-1). This method was applied to the determination of isoniazid in pharmaceutical formulation and enabled the determination of isoniazid in microgram quantities.     

High performance liquid chromatography coupled to an optical fiber detector coated with laccase for screening catecholamines in plasma and urine

An analytical method based on separation by high performance liquid chromatography (HPLC) and detection by optical fiber (OF) coated with an enzyme (laccase), has been developed for separation and quantification of catecholamines, namely epinephrine, dopamine and norepinephrine. The application of OF as a detector in this analytical system relies on the variation of the reflected optical power detected when the catecholamines eluted from the HPLC column act as the substrate of the laccase immobilized on a tip of a single-mode OF. The developed method shows a high linearity in a range between 5 and 125 pg/mL and detection limits of 3.5, 2.9 and 3.3 pg/mL for epinephrine, dopamine and norepinephrine, respectively. The analytical performance of the proposed method was compared with a classical analytical method, namely high performance liquid chromatography-electrochemical detector (HPLC-ED) regarding catecholamines detection, showing great analytical advantages such as low cost of equipment. Additionally, the proposed method was applied to catecholamines determination in actual samples of plasma and human urine.     

毛细管超薄池光度吸附测量新技术

在毛细管超薄池光度检测中首次采用吸收光强测量新技术,显著提高了测量的灵敏度和改善了信噪比。在内径50μm的石英毛细管超薄池以及由石英光导纤维构成的十字交叉超薄光学吸收池上,分别测量了系列高锰酸钾溶液吸收光强。吸收光强与高锰酸钾溶液浓度之间呈现良好的线性关系。对于10μg/mL的高锰酸钾稀溶液,毛细管超薄池吸收光强测量的信噪比相对于吸光度测量的有较大的改善。十字交叉池的光程约为40μm,容积约为0.02μL,具有较大的光能量,可望发展成为一种新型的电泳光度检测池。     

Flow injection determination of iodide ion in a photographic developing solution using iodide ion-selective electrode detector

A potentiometric flow injection determination method for iodide ion in a photographic developing solution was proposed by utilizing a flow-through type iodide ion-selective electrode detector. The sensing membrane of the electrode was Ag₂S–AgI membrane. The response of the electrode detector as a peak-shape signal was obtained for injected iodide ion in a photographic developing solution. A linear relationship in the subnernstian zone was found to exist between peak height and the concentration of the iodide ion in a photographic developing solution in a concentration range from 0 to 6.0×10⁻⁵ mol l⁻¹. The relative standard deviation for ten injections of 2×10⁻⁵ mol l⁻¹ iodide ion in a photographic developing solution was 0.96% and the sampling rate was approximately 12–13 samples h⁻¹. The iodide ion could be determined under coexisting of an organic reducing reagent and inorganic electrolytes of high concentration in a photographic developing solution sample solution by the present method.     

Flow injection on-line dilution for zinc determination in human saliva with electrothermal atomic absorption spectrometry detection

An automated method is described for the determination of zinc in human saliva by electrothermal atomic absorption spectrometry (ET AAS) after on-line dilution of samples with a significant reduction of sample consumption per analysis (<0.4 mL including the dead volume of the system). In order to fulfill this aim without changing the sample transport conduits during the experiments, a flow injection (FI) dilution system was constructed. Its principal parts are: one propulsion device (peristaltic pump, PP) for either samples, standards or washing solution all located in an autosampler tray and for the surfactant solution (Triton X-100) used as diluent, and a two-position time based solenoid injector (TBSI₁) which allowed the introduction of 10 μL of either solution in the diluent stream. To avoid unnecessary waste of samples, the TBSI₁ also permitted the recirculation of the solutions to their respective autosampler cups. The downstream diluted solution fills a home made sampling arm assembly. The sequential deposition of 20 μL aliquots of samples or standards on the graphite tube platform was carried out by air displacement with a similar time based solenoid injector (TBSI₂). The dilution procedure and the injection of solutions into the atomizer are computer controlled and synchronized with the operation of the temperature program. Samples or standards solutions were submitted to two drying steps (at 90 and 130 °C), followed by pyrolysis and atomization at 700 and 1700 °C, respectively. The aqueous calibration was linear up to 120.0 μg L⁻¹ for diluted standard solutions/samples and its slope was similar (p > 0.05) to the standard addition curve, indicating lack of matrix effect. The precision tested by repeated analysis of real saliva samples was less than 3% and the detection limit (3σ) was of 0.35 μg L⁻¹. To test the accuracy of the proposed procedure, recovery tests were performed, obtaining mean recovery of added zinc of 97.8 ± 1.3%. Furthermore, Zn values estimated by the procedure developed in this work were compared with those obtained by a standard addition flame-AAS method applied to 20 randomly selected saliva samples. No significant differences (p > 0.05) were obtained between the two methods. Zinc levels in saliva samples from 44 healthy volunteers, 15 male and 29 female, with ages between 20 and 51 years (mean 30.50 ± 9.14 years) were in the range 22–98 μg L⁻¹ (mean of 55 ± 17 μg L⁻¹), similar to some and different from others reported in the literature. It was found that zinc values for male were statistically higher (p = 0.006) than for female.     

A windowless flow cell-based miniaturized fluorescence detector for capillary flow systems

A miniaturized fluorescence detector utilizing a three-dimensional windowless flow cell has been constructed and evaluated. The inlet and outlet liquid channels are collinear and are located in the same plane as the excitation paths, while the optical fiber used to collect the emission light is perpendicular to this plane. The straightforward arrangement of the flow path minimizes band dispersion and eliminates bubble formation or accumulation inside the cell. The use of high-brightness light-emitting diodes (LEDs) as the excitation source and a miniaturized metal package photomultiplier tube (PMT) results in a compact and sensitive fluorescence detector. The detection limit obtained from the system for fluorescein isothiocyanate (FITC) in flow injection mode is 2.6 nmol/L. The analysis of riboflavin and FITC by packed capillary liquid chromatography is demonstrated.      

An automatic flow injection analysis procedure for photometric determination of ethanol in red wine without using a chromogenic reagent

An automatic reagentless photometric procedure for the determination of ethanol in red wine is described. The procedure was based on a falling drop system that was implemented by employing a flow injection analysis manifold. The detection system comprised an infrared LED and a phototransistor. The experimental arrangement was designed to ensure that the wine drop grew between these devices, thus causing a decrease in the intensity of the radiation beam coming from the LED. Since ethanol content affected the size of the wine drop this feature was exploited to develop an analytical procedure for the photometric determination of ethanol in red wine without using a chromogenic reagent. In an attempt to prove the usefulness of the proposed procedure, a set of red wines were analysed. No significant difference between our results and those obtained with a reference method was observed at the 95% confidence level. Other advantages of our method were a linear response ranging from 0.17 up to 5.14 mol L⁻¹ (1.0 up to 30.0%) ethanol (R=0.999); a limit of detection of 0.05 mol L⁻¹ (0.3%) ethanol; a relative standard deviation of 2.5% (n=10) using typical wine sample containing 2.14 mol L⁻¹ (12.5%) ethanol; and a sampling rate of 50 determinations per hour.     

Reverse saturable absorption of lanthanide bisphthalocyanines and their application for optical switches

We have investigated reverse saturable absorption (RSA) of tetrakis(2,9,16,23-tert-butyllanthanide bisphthalocyanines)(M(TBPc)₂, M=Lu, Dy, Tb) with Z-scan technique. Furthermore, lanthanide bisphthalocyanines have also been utilized for optical switches based on their RSA performance. However, the experimental results reveal that the performances of RSA and optical switches for M(TBPc)₂ (M=Lu, Dy, Tb) are poorer than that of tetrakis(2,9,16,23-tert-butylcopper phthalocyanines) (Cu(TBPc)) due to strong intramolecular π-π interaction between the two Pc rings.     

Flow injection analysis of potassium using an all-solid-state potassium-selective electrode as a detector

The concentration of potassium was determined by a combination of flow injection analysis (FIA) with an all-solid-state potassium sensor detection. The all-solid-state potassium-selective electrode possessing long-term potential stability was fabricated by coating an electroactive polypyrrole/poly(4-styrenesulfonate) film electrode with a plasticized poly(vinyl chloride) membrane containing valinomycin. The simple FIA system developed in this laboratory demonstrated sensitivity identical to that in the batch system and achieved considerably rapid assay (150 samples h⁻¹). Analyses of soy sauce and control serum samples by this FIA system yielded results in good agreement with those obtained by conventional measurements.     

流动注射分析血清中葡萄糖的电化学检测池

测定血清中葡萄糖含量是临床检验的重要项目之一。何立千曾对各种血糖测定方法做过综述。葡萄糖氧化酶-4-氨基安替比林-苯酚光度法(酶制剂法)虽能较好地测定血清中葡萄糖的含量,但成本较高,耗时长。因此有必要研究一种快速、廉价、稳定的分析方法。人们考虑到酶的专属性,对葡萄糖氧化酶电极做了大量工作,然而,这种电极的寿命仍不理想。     

Signal enhancement in capillary electrophoresis by using a sleeve cell arrangement for optical detection

This study comparts signal enhancement and efficiency in CZK employing three modes of detection: the sleeve cell (a simple method for creating a region of extended path length for absorption detection), the bubble cell (extended light path capillaries), and on-column detection in 75 μm i.d. capillary. Flow profile in the sleeve cell was monitored under a microscope. An abrupt change in capillary diameter in the sleeve cell region (from 50 μm to 220 μm) did not produce extensive band broadening. The sleeve-cell detection arrangement delivered a 3.5 fold increase in corrected peak area when compared with an oil-column detection in 75 μm i.d. column.     

Two-photon absorption and effective broadband optical power limiting properties of a multi-branched chromophore containing 2,3-diarylquinoxalinyl moieties as the electron-pulling units

A novel multi-branched chromophore containing 2,3-diarylquinoxalinyl units as the electron-acceptors had been synthesized and its nonlinear optical properties were characterized in the femtosecond and nanosecond regime. The experimental results show that the studied fluorophore possesses strong and wide-dispersed two-photon absorption in near infrared (NIR) region. It is demonstrated that the incorporation of 2,3-disubstituted quinoxaline moieties as a part of π-conjugation in a dye molecule could be a useful approach toward large molecular two-photon absoptivities within the studied spectral region. Effective optical-power-attenuation behaviors in the nanosecond time domain of this compound were also investigated and the results indicate that such dye molecule can be a potential material as a broadband and quick-responsive optical limiter especially when against those laser lights with longer pulses.     

An ion-exchange method for speciation of antimony by flow injection electrothermal atomic absorption spectrometry

In this work, a simple preconcentration system, achieved by replacing the sample tip of the autosampler arm by a micro-column packed with Amberlite IRA-910 or silica gel chelating resin functionalised with 1,5-bis(di-2-pyridyl)methylene tbiocarbohydrazide (DPTH-gel), is developed for the determination of Sb(V) and total antimony, respectively. Different factors including pH of sample solution, ionic strength, concentration and volume of eluent, sample flow rate, sample loading time and matrix effects for preconcentration were investigated. The method has been applied to the determination of antimony species in different samples.     

Flow field-flow fractionation with off-line electrothermal atomic absorption spectrometry for size characterization of silver nanoparticles

Flow field-flow fractionation (Fl-FFF) with off-line electrothermal atomic absorption spectrometry (ETAAS) detection was developed and employed for particle size characterization of Ag NPs stabilized by citrate, pectin, and alginate. Citrate stabilized-Ag NPs were prepared from sodium borohydride reduction of silver nitrate. Sodium citrate was used as the capping agent to stabilize Ag NPs and prevent the aggregation process. Pectin stabilized- and alginate stabilized-Ag NPs were prepared from ascorbic acid reduction of silver nitrate. Pectin and alginate were used as the capping agent for pectin stabilized- and alginate stabilized-Ag NPs, respectively. Three types of Ag NPs were characterized by using FlFFF, zeta potentiometer, and TEM technique. The mean particle sizes of Ag NPs as characterized by FlFFF were 9 nm, 19 nm, and 45 nm for citrate stabilized-, pectin stabilized-, and alginate stabilized-Ag NPs, respectively, in deionized water. Further, FlFFF with ETAAS detection was employed to observe the aggregation of Ag NPs of various types in environmental water in the absence and presence of humic acid. Citrate stabilized-Ag NPs underwent aggregation more rapid than the pectin stabilized- and alginate stabilized-Ag NPs as the latter two types were sterically stabilized. Further, humic acid could prolong the stability of Ag NPs in the environment.     

Cu(II)-imprinted styrene-divinylbenzene beads as a new sorbent for flow injection-flame atomic absorption determination of copper

The paper reports preparation and analytical features of a new Cu(II)-imprinted polymer, based on salen-OMe ligand 2,2′-[ethane-1,2-diylbis(nitrilo(E)methylylidene)]bis(6-allyl-4-methoxyphenol) and styrene-divinylbenzene matrix, as well as its application to on-line preconcentration and flame atomic absorption determination of copper. Sorbent beads (average diameter of 60-80 µm) were obtained using suspension polymerization technique and employed as a column filling. Copper sorption was the most effective at pH 6.8, whereas the highest elution effectiveness was observed when 0.5% HNO₃ was applied. The sorbent exhibited good long-term stability and acid resistance. Enrichment factor (EF) of 12 was found for 60 s loading time and loading flow rate of 4 mL min^− 1. EF value may be further increased by expanding the loading time and/or flow rate. Batch sorbent capacity in optimal pH conditions was found to be 0.16 mmol g^− 1 (9.55 mg g^− 1) of a dry polymer. Calcium(II) turned out to be the only significant interferent. Cadmium(II), silver(I), nickel(II), zinc(II) in concentrations lower than about 1 mg L^− 1 did not disturb copper(II) preconcentration. Different calibration methods such as: set of standards method (SSM), standard addition method (SAM) and combinatory calibration method (CCM) were employed for copper(II) determination in tap water, spring mineral water and certified reference material. Analysis of EU-H-3 reference material confirmed good accuracy of the proposed method. Relative standard deviation (RSD) was 3.2 for standard addition method and 2.8% for set of standard calibration method. Detection limit for sample consumption 16 mL was 1.03 and 1.07 µgL^-1 respectively.     

Design considerations regarding an atomizer for multi-element electrothermal atomic absorption spectrometry

The methodology of simultaneous multi-element electrothermal atomic absorption spectrometry (ETAAS-Electrothermal Atomic Absorption Spectrometry) stipulates rigid requirements to the design and operation of the atomizer. It must provide high degree of atomization for the group of analytes, invariant respective to the vaporization kinetics and heating ramp residence time of atoms in the absorption volume and absence of memory effects from major sample components. For the low resolution spectrometer with a continuum radiation source the reduced compared to traditional ETAAS (Electrothermal Atomic Absorption Spectrometry) sensitivity should be, at least partially, compensated by creating high density of atomic vapor in the absorption pulse. The sought-for characteristics were obtained for the 18 mm in length and 2.5 mm in internal diameter longitudinally heated graphite tube atomizer furnished with 2-4.5 mg of ring shaped carbon fiber yarn collector. The collector located next to the sampling port provides large substrate area that helps to keep the sample and its residue in the central part of the tube after drying. The collector also provides a “platform” effect that delays the vaporization and stipulates vapor release into absorption volume having already stabilized gas temperature. Due to the shape of external surface of the tube, presence of collector and rapid (about 10 °C/ms) heating, an inverse temperature distribution along the tube is attained at the beginnings of the atomization and cleaning steps. The effect is employed for cleaning of the atomizer using the set of short maximum power heating pulses. Preparation, optimal maintenance of the atomizer and its compliance to the multi-element determination requirements are evaluated and discussed. The experimental setup provides direct simultaneous determination of large group of element within 3-4 order concentration range. Limits of detection are close to those for sequential single element determination in Flame AAS with primary line source that is 50-1000 times higher than the limits obtainable with common ETAAS (Electrothermal Atomic Absorption Spectrometry) instrumentation.     

流动注射在线分离富集-电热原子吸收法测定地球化学样品中的痕量金、铂、钯

建立了流动注射在线同时分离富集，无火焰原子吸收法测定地球化学样品中金、铂、钯的分析方法。研究了联用技术并进行了吸附条件和解脱条件的优化实验。当采样频率为20样/h时，Au、Pt、Pd的富集倍数分别为43、37、41。Au、Pt、Pd的检出限(3σ)分别为5、16、9ng／L。将Au、Pt、Pd质量浓度分别为50、200、100ng／L的混合标准溶液平行测定7次，求得Au、Pt、Pd的相对标准偏差分别为3．6％、5．1％、4．7％。并对国家级标准样品进行了测定，其结果及精密度符合要求。     

Flow injection on-line dilution for flame atomic absorption spectrometry by micro-sample introduction and dispersion using syringe pumps

A robust flow injection (FI) on-line dilution system based on micro-sample introduction was developed for flame atomic absorption spectrometry (FAAS). Two computer programmed and stepper-motor driven syringe pumps were used for the precise and reproducible sample metering in micro-liters and carrier delivery. Factors, which might influence the performance of the system, such as sample matrix and carryover, were investigated. No inferior effects were observed with various matrices including 10% glycerol. Sample carryover effects were less than 0.4%, tested by analyzing a blank and a sample alternately. Dilution factors were decided and keyed in manually. The system was calibrated using a set of concentrated standard solutions for a given dilution factor. At a sampling frequency of 60 h⁻¹, precisions were better than 2% R.S.D. (n=40) for dilution factors of 10-2000. The long-term stability of the system was examined by continuously running the system for a whole working day, and a precision of 2.6% R.S.D. (n=345) was obtained at a dilution factor of 1000. The system was verified by analyzing a standard copper alloy with a certified concentration of 57.4% Cu, resulting in a measurement solution with 574 mg l⁻¹ Cu.