Synthesis and properties of oxetane‐based polysiloxanes used for cationic UV curing coatings

The polysiloxanes end‐capped with oxetane group (PSiO‐H and PSiO‐L) were synthesized via hydrosilylation reaction based on α,ω‐dihydrogen‐terminated polydimethylsiloxanes with a higher (0.23%, PDSi‐H) and lower (0.12%, PDSi‐L) hydrogen amount. The molecular structures were characterized by FT‐IR and ¹H NMR spectroscopy. The polysiloxanes were added into a commercial oxetane‐based resin, 3,3′‐(oxydi(methylene)) bis(3‐ethyloxetane) (DOX), as an additive to prepare a series of cationic UV curable formulations. The photo‐DSC results showed that the maximum photopolymerization rate decreased while the oxetane conversion increased with the polysiloxane content increasing. The surface hydrophobic property of cured films was improved having the water contact angles of 97° and 99° compared with 82° of the cured DOX film with only 1 wt% PSiOs, respectively. The dynamic mechanical thermal analysis results showed that both the storage modulus on the rubbery plateau region and the glass transition temperature decreased with increasing PSiO‐H loading. Moreover, the decrease became more obvious as PSiO‐L was added instead of PSiO‐H due to its lower concentration of oxetane group. The thermal stability of cured films was enhanced by the addition of PSiOs from the thermogravimetric analysis. And the DOX/PSiO‐H film possessed higher thermal degradation temperatures than DOX/PSiO‐L film. Copyright © 2011 John Wiley & Sons, Ltd.     

三维有序多孔图案化SiC陶瓷的制备

结合毛细管微模塑技术、模板技术和先驱体转化技术, 以图案化聚二甲基硅氧烷(PDMS)弹性体为模具,以氧化硅凝胶小球为模板, 以液态聚碳硅烷(PCS)为先驱体, 经过氧化硅凝胶小球图案化模板的形成, 先驱体的渗入, 模板中先驱体的交联, 弹性模具的去除, 图案化先驱体的无机化和模板的去除, 制备了图案化多孔SiC 陶瓷.研究结果表明：所制备的图案化多孔陶瓷中, 图案的尺寸受图案化PDMS 弹性模具的控制, 球形孔的孔径可由氧化硅凝胶小球来调节. 图案化陶瓷中球形孔不仅三维有序排列, 而且由于模板中小球的相互接触形成的“窗 口”使球形孔三维贯通.     

可紫外光固化的聚乙烯基硅氮烷合成与表征

采用带丙烯酸酯基团的烯丙基溴化合物(4-溴丁烯酸乙酯)和聚乙烯基硅氮烷发生取代反应,实现了丙烯酸酯基团在聚乙烯基硅氮烷主链上的链接.采用质子核磁共振谱(1H-NMR)和二维质子核磁共振谱(2D-1H-1H-NMR)对分子结构进行了表征,采用光学差热分析仪(Photo-DSC)和傅立叶转换红外光谱仪(FT-IR)测试了改性高分子的光敏性能,用热重分析仪(TGA)分析了产物在高纯氮气氛围下的陶瓷收率.结果表明,通过分子改性,交联固化时间从改性前的20min减少到1min之内,功能化的聚乙烯基硅氮烷可以在光刻蚀工艺中作为负性光刻胶使用.     

Photochemical structuring and fixing of structures in binary polymer brush layers via 2pi+2pi photodimerization

Binary polymer brushes grafted to Si wafers were prepared from hydrophilic and hydrophobic polymer components, which allow switching the surface properties (as revealed by contact angles) by exposure to varying solvents. The hydrophilic component was poly-2-vinylpyridine; the hydrophobic component was a copolymer of styrene and 2-(4-vinylphenyl)indene containing the photodimerizable phenylindene chromophore. The brushes were prepared via thermal and via photochemical grafting-to methods, which led to distinct layer thicknesses. Structural patterns differing in surface properties were produced and fixed via crosslinking the hydrophobic component by 2pi+2pi photodimerization of phenylindene moieties. The patterns were visually observable.     

Palladated halloysite hybridized with photo‐polymerized hydrogel in the presence of cyclodextrin: An efficient catalytic system benefiting from nanoreactor concept

Considering the excellent performance of halloysite as a catalyst support and in an attempt to benefit from the concept of nanoreactors in the catalysis, an innovative catalytic system has been designed, in which acrylamide and bis‐acrylamide were photo‐polymerized in the presence of palladated halloysite. The novel precipitation photo‐polymerization method avoided the formation of an extended polymeric network, but led to the formation of co‐polymer on the halloysite periphery. The co‐polymer exhibited good swellability in aqueous media and formed hydrogel. This hydrophilic environment around catalytic palladated halloysite can be considered as a nanoreactor that can concentrate the substrate and bring them into the vicinity of the palladated halloysite. This catalytic system was used for promoting hydrogenation of hydrophobic nitro arenes in aqueous media. To avoid immiscibility of hydrophobic substrates and hydrophilic nature of the nanoreactor, that emerged from swelling of hydrogel, β‐cyclodextrin (CD) was utilized as phase transfer agent. The results confirmed high catalytic activity of this catalytic system. Even highly hydrophobic substrates could tolerate hydrogenation under this protocol to furnish the corresponding product in high yield. Finally, the contribution of both CD and hydrogel to the catalysis was confirmed. Moreover, studying the recyclability of the catalyst as well as Pd leaching proved the high recyclability of the catalyst and low leaching of Pd nanoparticles.     

Silica nanoparticles at interfaces modulated by amphiphilic polymer and surfactant

The interfacial behavior of silica nanoparticles in the presence of an amphiphilic polymer poly( N-isopropylacrylamide) (PNIPAM) and an anionic surfactant sodium dodecyl sulfate (SDS) is studied using neutron reflectivity. While the nanoparticles do not show any attraction to hydrophilic and hydrophobic surfaces in pure water, presence of the amphiphilic polymer induces significant adsorption of the nanoparticles at the hydrophobic surface. This interfacial behavior is activated due to interaction of the nanoparticles with PNIPAM, the amphiphilic nature of which leads to strong adsorption at a hydrophobic surface but only weak interaction with a hydrophilic surface. The presence of SDS competes with nanoparticle-PNIPAM interaction and in turn modulates the interfacial properties of the nanoparticles. These adsorption results are discussed in relation to nanoparticle organization templated by dewetting of charged polymer solutions on a solid substrate. Our previous studies showed that nanoparticle assembly can be induced to form complex morphologies produced by dewetting of the polymer solutions, such as a polygonal network and long-chain structures. This approach, however, works on a hydrophilic substrate but not on a hydrophobic substrate. These observations can be explained in part by particle-substrate interactions revealed in the present study.     

可紫外光交联氟代聚芳醚的合成及性能研究

以丙酮酸、苯甲醚为原料合成了1,1-双(4-甲氧基苯基)(BMPE)乙烯单体,并通过去甲基反应得到了含可交联基团的二酚单体1,1-双(4-羟基苯基)乙烯(BHPE),并且用核磁共振、飞行质谱及元素分析表征了单体的结构,DSC测试了单体的熔点.并将BHPE与全氟联苯(DFBP)在氟化钾和氢化钙的催化作用低温下进行缩聚反应,得到了一种可紫外辐照交联的氟代聚芳醚.通过核磁共振证明了所合成的单体以及聚合物的结构,凝胶渗透色谱(GPC)测定了聚合物的分子量.傅立叶变换红外光谱分析了聚合物紫外辐照下的交联反应.所合成的氟代聚芳醚在室温下可溶于氯仿、四氢呋喃等有机溶剂,紫外交联后不溶于任何有机溶剂.且合成的聚合物具有良好的热稳定性能(玻璃化转变温度为160℃,交联后的5%热失重为465℃).     

Surface Reconstruction by a Coassembly Approach

Materials with switchable surfaces, capable of changing surface properties under external stimuli, are playing a pivotal role in many applications, such as tissue engineering, biosensors, and drug/protein delivery. In this research silica particles with patterned and switchable surfaces are fabricated. Surface micelles on silica particles are formed by coassembly of polymer brushes and “free” block copolymer chains in a selective solvent. The cores of the surface micelles are crosslinked by anthracene photodimerization. After quaternization of the coronae, amphiphilic surface micelles are prepared. The surface micelles are able to rearrange in different media. After treatment with an organic solvent, the surfaces of silica particles are occupied by hydrophobic polymer components; in aqueous solution, the positively charged polymer chains are on the surfaces. The switching of the surface micelles results in changes in surface composition and wetting behaviors.     

Synthesis and cationic photopolymerization of new fluorinated,polyfunctional propenyl ether oligomers

New fluorinated, polyfunctional propenyl ether functionalized resins were synthesized, and their behavior in cationic photopolymerization was investigated. The photopolymerization proceeded efficiently with a high double‐bond conversion (>90%), giving rise to UV‐cured coatings characterized by low glass‐transition temperatures (?33 °C ≤ glass‐transition temperature ≤ ?15 °C) and hydrophobic surface properties. A fluorinated additive was also employed as a reactive additive in the cationic photopolymerization of trimethylolpropane tripropenyl ether, increasing the double‐bond conversion, polymer network flexibility, thermal stability, and surface hydrophobicity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6943–6951, 2006     

聚合物涂层光稳定化研究进展

用于改造各种材料的表面性质并防止其光老化的聚合物涂层的光稳定化技术近年来已经成为高分子材料科学和光化学领域的又一研究热点。本文以紫外光固化聚合物涂层为重点综述了该研究领域的发展过程、理论研究特点和应用技术的生长点,并对聚合物涂层光稳定化技术的最新进展进行了评述,讨论了聚合物涂层光稳定化技术中新型光固化树脂,多功能单体、光引发剂和光稳定剂（包括紫外吸收剂和受阻胺类稳定剂）的特点及作用机理。     

Role of additives in the water vapor transport through block co-poly(amide/ether) membranes: effects on surface and bulk polymer properties

In the last years there has been a growing industrial interest in modifying the performance of traditional polymers by using additives, working as modifiers for processing, rheological, transport, bonding, and pigmentation properties. This work was focused on the understanding of the relationships between chemical structure and water vapour transport through a polymer matrix modified by different additives regarding hydrophilicity and molecular structure. A screening of the changes in surface energies and bulk morphology, as a function of the chemical nature and weight percent modifier, allowed estimating the effects on the water vapour transport through polymer membranes. Static and dynamic contact angle measurements explained the difference in surface wettability and affinity to polar species such as water molecules. Modifiers having polar groups improved the surface hydrophilicity, enhancing the breathability of the membranes, while hydrophobic components such as aromatic structures led to a reduction of the water vapour mass uptake onto the membrane surface. On the other hand, thermal analyses showed a tendency of the polymer structure to reduce its own mobility with consequent slowdown of the diffusion through polymer matrix. Modification with large and bulky structures disrupted the polymer packing density, but simultaneously increased the stiffness of the polymer chains, inhibiting the penetrant migration. As a result, balancing the effects due to modifier polarity and bulky structure, it is possible to change the performance of a polymer in terms of transport, going from breathable membranes to barrier films.     

Macroporous SiC?MoSi2 ceramics from templated hybrid MoCl5–polymethylsilane

A molybdenum‐containing preceramic polymer, MoPMS, was synthesized for the first time by HCl elimination of polymethylsilane (PMS) and MoCl₅ at room temperature in tetrahydrofuran. The insoluble MoPMS prepared was embedded into the void spaces of a silica colloidal crystal template within the pot life of the polymer and successfully transformed to a three‐dimensionally long‐range‐ordered macroporous SiC? MoSi₂ ceramic after pyrolysis at 1400 °C in an argon atmosphere followed by template removal in HF. The bead‐inverse macroporous SiC? MoSi₂ ceramic, with a ceramic yield of about 88%, exhibits high temperature stability, high BET surface area, and semiconducting behavior. In addition, the macroporous SiC? MoSi₂ ceramic was used as a catalyst carrier for platinum–ruthenium coated on the surface of the pores. The preceramic polymer and the ceramic were characterized by IR, thermogravimetric analysis, X‐ray diffraction, scanning and transmission electron microscopy, and BET surface area. Copyright © 2005 John Wiley & Sons, Ltd.     

Effect of molecular architecture and size of mesogen on phase behavior and photoactive properties of photoactive liquid crystalline hyperbranched polyester epoxies containing benzylidene moiety

A series of photoactive liquid crystalline linear and hyperbranched polyester epoxies were synthesized by polyaddition of photoactive bis benzylidene alkanone diol monomers and terephthalic acid and trimesic acid respectively with good yield. The effect of molecular architecture (linear and hyperbranched), size of mesogenic unit (cyclic and acyclic units) on the physicochemical, thermal, mesogenic, and photoactive properties of hyperbranched polymers were studied and compared. Degree of branching of hyperbranched polymers was found to be in the range of 0.46–0.49. Monomers containing cyclic moieties only exhibited nematic mesophase, while all polymers exhibited typical nematic mesophase. Intermolecular photo cycloaddition reaction was studied by ultraviolet–visible spectra (UV–vis) and NMR spectroscopy and photo viscosity measurement of UV irradiated polymer solutions. Faster photo induced behavior of hyperbranched polymers containing acyclic alkanone moiety, as compared to polymers containing cycloalkanone moieties, was observed. The change in the refractive index was found to be in the range of 0.02–0.024. Substantial variation of refractive index indicates that this polymer could be used for optical recording. All the polymers were also found to be fluorescent in nature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 552–563, 2008     

Preparation and characterization of structured hydrogel microparticles based on cross-linked hyperbranched polyglycerol

The aim of this work was to obtain well-defined HyPG-MA (methacrylated hyperbranched polyglycerol) microparticles with uniform sizes. Therefore, three different preparation methods were evaluated. First, we assessed a micromolding technique using rigid SU-8 (a photoresist based on epoxies) grids. Independent of the surface treatment of the SU-8 grid or the type of polymer used, approximately 50% of the microgels remained attached to the SU-8 grid or broke into smaller particles during the release process in which drying of the gels was followed by a sonication process. Although 90% methacrylate conversion could be obtained, this method has some additional drawbacks as the obtained dried microgels did not rehydrate completely after the drying step. Second, a soft micromolding technique was evaluated using elastomeric PDMS (poly(dimethyl siloxane)) grids. The use of these flexible grids resulted in a high yield (80-90% yield; >90% methacrylate conversion) of microgels with a well-defined size and shape (squares 100 microm x 100 microm x 50 microm or hexagons with ? 30 microm and a thickness of 20 microm) without the occurrence of water evaporation. However, a number of particles showed a less-defined shape as not all grids could be filled well. The microgels showed restricted swelling, implying that these gels are dimensionally stable. Third, an alternative method referred to as photolithography was evaluated. This method was suitable to tailor accurately the size and shape of HyPG-MA microgels and additionally gained 100% yield. Well-defined HyPG-MA microgels in the size range of 200-1400 microm (thickness of 6, 20, or 50 microm), with a methacrylate conversion of >90%, could easily be prepared by adding an inhibitor (e.g., 1% (w/v) of vitamin C) to the polymer solution to inhibit dark polymerization. Microgels in the size range of 30-100 microm (>90% conversion) could only be obtained when applying the photomask in direct contact with the polymer solution and using a higher (i.e., 2% (w/v)) concentration of vitamin C. Additionally, the microgels showed limited swelling, indicating that rather dimensionally stable particles were obtained. In conclusion, this paper shows that photolithography and soft micromolding, as compared to rigid micromolding, are the most appropriate techniques to fabricate structured HyPG-MA microgels with a tailorable and well-defined size and shape. These microgels have great potential in tissue engineering and drug delivery applications.     

Silicon Oxycarbide Foams from a Silicone Preceramic Polymer and Polyurethane

Ceramic open-cell foams were obtained from a preceramic polymer (a silicone resin) and blown polyurethanes, by pyrolysis at 1200°C in nitrogen. Silicon carbide submicron powders were also added to the silicone resin to give SiOC + SiC composite foams. The morphology of the foams was dependent on the architecture of the blown polyurethanes. The crushing strength as well as the elastic modulus increased with increasing relative density, reaching values as high as 14 and 450 MPa, respectively. Some of the foams displayed an excellent thermal stability (resistance to oxidation in air and decomposition in inert atmosphere) up to elevated temperatures.     

Surface characteristics of a self-polymerized dopamine coating deposited on hydrophobic polymer films

This study aims to explore the fundamental surface characteristics of polydopamine (pDA)-coated hydrophobic polymer films. A poly(vinylidene fluoride) (PVDF) film was surface modified by dip coating in an aqueous solution of dopamine on the basis of its self-polymerization and strong adhesion feature. The self-polymerization and deposition rates of dopamine on film surfaces increased with increasing temperature as evaluated by both spectroscopic ellipsometry and scanning electronic microscopy (SEM). Changes in the surface morphologies of pDA-coated films as well as the size and shape of pDA particles in the solution were also investigated by SEM, atomic force microscopy (AFM), and transmission electron microscopy (TEM). The surface roughness and surface free energy of pDA-modified films were mainly affected by the reaction temperature and showed only a slight dependence on the reaction time and concentration of the dopamine solution. Additionally, three other typical hydrophobic polymer films of polytetrafluoroethylene (PTFE), poly(ethylene terephthalate) (PET), and polyimide (PI) were also modified by the same procedure. The lyophilicity (liquid affinity) and surface free energy of these polymer films were enhanced significantly after being coated with pDA, as were those of PVDF films. It is indicated that the deposition behavior of pDA is not strongly dependent on the nature of the substrates. This information provides us with not only a better understanding of biologically inspired surface chemistry for pDA coatings but also effective strategies for exploiting the properties of dopamine to create novel functional polymer materials.     

Photopolymerization of Dendritic Acrylated Aromatic/Aliphatic Polyesters and Properties of Their Cured Films

Introduction　　 Radiation( UV/EB) curing technology iswidely used for the preparation of curablematerials,such as inks,coatings and compositesdue to their high cure rate,environmentalprotection,and the saving of energy[1～ 3 ] .For theprocessing of resins as the application,two basicparameters are the most important,namely,theresulting degree of conversion of functional groupsand the polymerization kinetics during the curing,which determine the value for its intended end use.　　 The dendri…     

腰果酚的紫外光固化机理和固化膜性能

研究了腰果酚在无光引发剂条件下的紫外光固化反应,并用IR、UV、元素分析、GPC等分析手段分析了腰果酚的紫外光固化机理及其固化膜性能。结果表明:在紫外光辐照下,腰果酚通过侧链发生氧化聚合反应,和酚羟基的邻对位失去质子形成的自由基引起的苯环缩合反应,最终形成体型高聚物。腰果酚的紫外光固化膜的常规物理机械性能、抗溶剂性、耐化学介质腐蚀性、热稳定性和抗紫外线性能均优于腰果酚醛缩聚物(PC)涂膜。     

Impact of polymeric films and hydrogels: Physical characteristics on bacterial growth

Hydrogels find diverse applications in manipulating bacteria, and serving purposes like elevation, maintenance, and elimination. Several factors of hydrogel have been studied in the benefits of antibacterial activity. Factors such as hydrogel stiffness and roughness gain significance in surface coating, influencing bacterial behavior. However, the intricate interplay of hydrogel stiffness, roughness, polymer types, and bacterial species necessitates further exploration. The choice of polymer is dictated by the specific objectives, particularly in antibacterial scenarios where polymers with positive charge, hydrophilicity, and acidity prove effective. These properties induce robust electrostatic and hydrophobic/hydrophilic interactions, along with pH-induced cell membrane damage, collectively contributing to hindered bacterial adhesion and growth. Additionally, extracellular polymeric substances (EPS) emerge as pivotal influencers in bacterial adhesion and proliferation. EPS production alters bacterial surfaces, fostering connections between bacteria and facilitating biofilm formation. The hydrophobic nature of EPS further complicates bacterial interactions with surface materials, emphasizing the nuanced interplay of hydrophilic and hydrophobic forces in bacterial adhesion. Herein, this work article has reviewed the related study of each physical property related to antibacterial property on the surface of the hydrogel. Moreover, this work also illustrates applications of the antibacterial properties of hydrogel for medical and surface treatment, including wound healing, food packaging, and surface coating. Additionally, the bacteria growing on hydrogel for engineered living materials, have been updated in various applications.     

Thermal degradation of polyethylene containing antioxidant and hydrophilic/hydrophobic silica

High-density polyethylene, its composites with hydrophilic/hydrophobic silica and the antioxidant BHT (butylated hydroxytoluene) were studied using the thermogravimetric analysis. It has been shown that filling with silica as well as introducing BHT into the unfilled polymer increases the thermal-oxidative stability of the polymer. Immobilized BHT is inactive and it suppresses the stabilizing effect of hydrophobic silica surface in the processes of thermal oxidation at the initial stage. However, being gradually released from the surface antioxidant prolongs the resistance of the polymer against oxidation.