Solid-Phase Extraction with Slurry Injection of the Resin Into ETAAS for Trace Determination of Thallium in Natural Water

Thallium in natural water samples was determined by electrothermal atomic absorption spectrometry after 1000-fold enrichment by mini solid-phase extraction from a 100-mL sample solution. A Tl-pyrrolidine-1-carbodithioate complex formed in a sample solution of pH 1.6 was extracted on fine particles of a cellulose nitrate resin dispersed in the sample solution. The cellulose nitrate resin was then collected on a membrane filter (25mm^ø) by filtration under suction using a glass funnel with an effective filtration area of 0.64cm². As a result, a circular thin layer of the resin phase with a diameter of 9mm was obtained. Then the resin phase was carved out by an acrylate resin puncher with a 10-mm^ø hole to put it into a sample cup containing 100µL of 10mM HNO₃ containing 0.5mM NaCl. The resin phase was suspended in the solution by ultrasonication. 1000-fold enrichment was thus attained within 15min, and the suspension was delivered to electrothermal atomic absorption spectrometry. The linear calibration graph was obtained in the range of 0–4ng of Tl in 100mL of a sample solution. The detection limit obtained by 3 method was 0.19ng. The proposed method was applied to the determination of Tl in natural water samples. The results showed the concentration of Tl in seawater was 12.1±1.8pgmL^–1 for the calibration graph method and 12.6±1.4pgmL^–1 for the standard addition method. A snowmelt sample contained 20.7±1.0pgmL^–1 of Tl.     

Kinetics of formation,dissociation and equilibrium constants of pentacyanoaquoruthenate(II) with heterocycles

The kinetics of formation and dissociation reactions of [Ru(CN)₅L]^3– with a series of heterocyclic ligands were studied in aqueous media. In this presence of an excess of heterocycle, the observed second order rate constants were calculated from the k_obs versus [ligand] plot at =0.100m NaClO₄. Activation parameters for the formation reactions (H=28±7kJmol^–1 and S=140±35JK^–1mol^–1) are comparable for all systems, indicating a common mechanism. The kinetics of exchange of coordinated heterocycles for 1,3,5-triazine yielded a rate saturation typical of a limiting dissociative mechanism. Activation parameters of the limiting first order specific rate of dissociation reactions were H=85±7kJmol^–1 and S=18±4JK^–1mol^–1. Equilibrium constants were calculated from the second order rates of formation and pseudo-first order rates of dissociation reaction.     

Solvent Sublation Using Dithizone as a Ligand for Determination of Trace Elements in Water Samples

Solvent sublation was studied as a method of separating and pre-concentrating traces of Zn(II), Cd(II) and Cu(II) as diphenylthiocarbazone (dithizone) complexes for their determination. The experimental conditions, such as pH of solution, amount of dithizone as ligand, stirring time, gas flow rate and flotation time, were optimized. Different non-ionic surfactants and types of organic solvents were optimized for efficient sublation. The analyte ions in a 350mL sample were complexed as metal-dithizone complexes by adding 10mL of 0.084% dithizone, 0.5mL of 0.1% nonylphenol polyoxyethylene ether (NP) and 10mL of pH 4.3 potassium hydrogen phthalate-sodium hydroxide buffer solution. The solution was stirred with a mechanical stirrer for 30min. It was transferred to a flotation cell, and the complexes were floated by bubbling air and extracted into 10mL of methylisobutyl ketone (MIBK) on the surface of the aqueous solution. The analytes in the organic phase were determined by flame atomic absorption spectrometry (F-AAS) for Zn(II) and by graphite furnace atomic absorption spectrometry (GF-AAS) for Cd(II) and Cu(II). The proposed method was applied to determine Zn(II), Cd(II) and Cu(II) in real water samples; the enrichment factor was more than 37, the RSD was less than 4.26%, recoveries ranged from 92.7 to 107.3%, and the detection limits were 1.0µgL^–1 for Zn(II), 0.006µgL^–1 for Cd(II) and 0.06µgL^–1 for Cu(II). The results obtained were satisfactory.     

Au-Induced Faceting of Si(5 5 12)

The growth of Au on the stable, high-index Si(5512) surface has been studied using scanning tunneling microscopy (STM). At very low coverages and moderate annealing temperatures (0.1ML, 400–500°C), Au appears to decorate the underlying Si rows and form an array of rows that maintains the underlying (5512) periodicity of 5.4nm. For higher annealing temperatures and coverages, however, Au causes faceting to a number of nearby planes. The two primary facets formed at lower (0.15ML) and higher (0.5–2ML) coverages are the (337) and (225) planes, which are tilted 0.7° down [towards (111)] and 1.1° up from (5512), respectively. Both orientations are in fact subunits of the (5512) unit cell, so their presence is not surprising. In addition to these facets, two types of sawtooth morphologies composed of planes oriented further from (5512) are found at very high annealing temperatures (800–900°C). These include (113)+(7715) planes at very low coverage (0.05ml) and (113)+(5511) planes at higher coverage (1ML), where (113) is tilted up by 5.3° and (7715) and (5511) are tilted down by 2.9° and 2.2°, respectively. Au adsorption on Si(5512) therefore results in the formation of five possible facet planes: (113), (225), (337), (5511), and (7715).     

Mixed ligand complexes involving aminoacid dithiocarbamates,substituted phosphines and nickel(II)

Mixed ligand complexes involving four aminoacid dithiocarbamates (RRdtc=glydtc^– (R=H; R=H), methdtc^– (R=H; R=C₃H₇S), sardtc^– (R=Me; R=H), trydtc^– (R=H; R=C₉H₈N), substituted phosphines [PPh₃, Ph₂PCH₂CH₂PPh₂(dppe)] and nickel(II) are reported. All are diamagnetic. Thermal analyses of the complexes are in keeping with the proposed formulae. Thermal decomposition of the dithiocarbamate moiety proceeds through the formation of Ni(SCN)₂. PPh₃ and dppe are lost in the initial decomposition stages.     

Determination of Lead Using a New Chromogenic Reagent 2-(2-Sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic Acid

A novel chromogenic reagent, 2-(2-sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic acid 1, was prepared by diazo coupling of 4-acetylaniline-2-sulfonic acid and 2,4,6-trichloroaniline to chromotropic acid through –N=N– groups. Based on this reagent, a simple, sensitive and selective spectrophotometric method was developed for the determination of lead. In 0.20M phosphoric acid medium, lead reacts with 1 to form a 1:2 blue complex with an absorption maximum of 654nm. Beers law is obeyed in the range of 0–0.6mgL^–1 of lead. The apparent molar absorptivity is 1.25×10⁵Lmol^–1cm^–1. The detection limit and quantification limit were found to be 0.63µgL^–1 and 2.1µgL^–1, respectively. The relative standard deviation for eleven replicate measurements was of 2.6%. The interference of foreign ions was also investigated. All the other foreign ions studied did not interfere with lead determination except for Ca(II) and Ba(II). The interference caused by Ca(II) and Ba(II) can be eliminated by prior extraction of lead with potassium iodide-methylisobutylketone (KI-MIBK). The proposed method was applied to the determination of lead in certified samples with satisfactory results.     

Voltammetric Determination of Trace Amounts of Fenitrothion on a Novel Nano-TiO2 Polymer Film Electrode

A novel nano-TiO₂ polymer modified glassy carbon (GC) electrode was developed for the determination of an organophosphorous pesticide, fenitrothion (-NO₂), in citrate buffer solution. The electrochemical behavior of fenitrothion was characterized by using cyclic voltammetry. An irreversible form, -NO₂, was transformed into a reversible redox couple (-NHOH/-NO), and it can be used to determine trace fenitrothion by square wave voltammetry. The experimental parameters, such as film thickness, pH value, accumulation potential and time were optimized. Interestingly, a cyclic voltammetric scan was observed to be more effective than a constant potential for the accumulation of fenitrothion. A linear response over a fenitrothion concentration of 2.5×10^–8 to 1.0×10^–5M was exhibited, with a detection limit of 1.0×10^–8M (S/N=3). The high sensitivity and selectivity of this film electrode was demonstrated by its practical application to the determination of trace amounts of fenitrothion in lake water and apple samples.     

Syntheses and properties of mixed dinuclear copper(II) complexes with heterocyclic dithiocarbamates and a cyclic octadentate tertiary amine

Five new Cu^II complexes of general formula [Cu₂(Rdtc)tpmc](ClO₄)₃, (1)–(5), where tpmc and Rdtc ^– refer to N,N,N,N-tetrakis(2-pyridylmethyl)-1,4,8,11-teraazacyclotetradecane and piperidine- (Pipdtc), 4-morpholine- (Morphdtc), 4-thiomorpholine- (Timdtc), piperazine- (Pzdtc) or N-methylpiperazine- (N-Mepzdtc) dithiocarbamates, respectively, have been prepared. Elemental analyses, conductometric and magnetic measurements, u.v./vis, i.r., e.p.r. and mass spectroscopy have been employed to characterize them. The complexes adopt an exo coordination of Cu^II ions and tpmc. The dithiocarbamate ion joins both the sulphur and the copper atoms acting as a bridging ligand The presence of different heteroatoms in the piperidine ring influences the (C=N) and (C=S) vibrations which decrease in the order of the complexes: Pipdtc>N-Mepipdtc>Pzdtc>Morphdtc>Timdtc ligands. Attention has been paid to the detailed mechanism of the mass spectral fragmentation of the complexes. The g _eff factors of the complexes have been also estimated by e.p.r. spectra. Finally, the complexes obtained demonstrate microbiologycal activity against some bacteria.     

Determination of Total Selenium Content in Cereals and Bakery Products by Flow Injection Hydride Generation Graphite Furnace Atomic Absorption Spectrometry Applying in-situ Trapping on Iridium-Treated Graphite Platforms

A flow injection hydride generation graphite furnace atomic absorption spectrometric (FI-HG-GFAAS) method was applied to the determination of Se in Se-doped and undoped cereals and bakery products. For the purpose of doping, the soils used for the cultivation of the cereals were dosed with Se-doped foliar fertilizers. The samples were dissolved in a mixture of HNO₃ and H₂O₂ solutions using microwave-assisted digestion. The decomposition of H₂Se generated from the sample solutions and the trapping of elemental Se were performed at a temperature of 300°C on an Ir-pretreated integrated graphite platform of a transversally heated graphite atomizer (THGA). For release of the trapped Se within a fairly short atomization time (5s), an atomization temperature of 2200°C was observed to be optimal. The overall efficiency of hydride generation, transport and trapping was 86%.The upper limit of the linear dynamic range of calibration was 10µgL^–1, which corresponds to 0.5µgg^–1 for solid samples. Recovery of the samples spiked with Se^VI solutions was found to be 93±6% on average. The relative standard deviation of the determinations was less than 8%. The limit of detection was found to be 0.06µgL^–1, corresponding to 3ngg^–1 for solid samples. The accuracy of the method was verified with the use of IAEA-155 (whey powder) certified reference material. End-capped THGA tubes resulted in an extension of the linear calibration range compared to that of standard THGAs.The Se content in bakery products made of undoped cereals ranged from 7.7 to 68ngg^–1 (wet weight) in 18 samples, whereas the Se content of the corresponding cereals was found to be below 100ngg^–1 (wet weight). The Se level of cereals grown on soils treated with Se-doped fertilizers ranged from 128 to 1046ngg^–1 (wet weight), and it depended linearly on the Se concentration of the corresponding foliar fertilizer.     

Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Flame Atomic Absorption Spectrometric Determination of Gold and Palladium Using Microcolumn On-line Preconcentration and Separation

A microcolumn on-line preconcentration and separation system was developed for the flame atomic absorption spectrometric (FAAS) determination of trace levels of gold and palladium. The analytes were selectively adsorbed onto the microcolumn packed with 2-mercaptothiazole immobilized silica gel (MBTSG) in an acidity range of 0.1 to 6.0M HCl at a sampling flow rate of 4.0mLmin^–1. The analytes adsorbed could be desorbed by a thiourea solution with a flow rate of 2.0mLmin^–1. Most of the common coexisting metal ions at a concentration of 25.0mgmL^–1 and anions at a concentration of 50.0mgmL^–1 did not interfere with the preconcentration and determination of Au and Pd. The limits of detection (LOD), defined as three times the standard deviation of the blank (3), of Au and Pd are 10ngmL^–1 and 26ngmL^–1, respectively, with a preconcentration time of 60s. The relative standard deviation (RSD) is about 2.0% for 0.20µgmL^–1 Au and 0.30µgmL^–1 Pd. With a sample loading time of 30min, 6.7ngmL^–1 Au and 10ngmL^–1 Pd can be preconcentrated quantitatively. A geological sample, an anode slime and a secondary nickel alloy were successfully determined with the proposed method, and the results obtained showed good agreement with the certified values.Received December 23, 2002; accepted May 14, 2003 Published online August 8, 2003     

Determination of Caffeine Using a Simple Graphite Pencil Electrode with Square-Wave Anodic Stripping Voltammetry

A simple commercial graphite pencil electrode (GPE) was utilized for monitoring caffeine using the square-wave anodic stripping voltammetry (SWASV) method. This method was applied to determine the caffeine levels in several tea samples, which yielded a relative error of 1% in the concentrations. Caffeine was deposited at 0.0V (vs. Ag/AgCl), then reduced at +1.40V to strip it on the GPE. Optimal experimental conditions for the analysis were found to be as follows: pH value of 9 for the medium; deposition potential of 0.0V; deposition time of 120s; SW frequency of 25Hz; SW amplitude of 45mV, and step potential of 6mV. Given these optimum conditions, a linear range was observed within the concentration of 0500mgL^–1. At caffeine concentrations of 50.0, 250.0, and 500.0mgL^–1, the relative standard deviations in measured concentrations (n=12) were 0.19, 0.09, and 0.11%, respectively. The detection limit was found to be 9.2mgL^–1, which is comparable with the result obtained using a carbon paste electrode, equivalent to 8.2mgL^–1.     

Determination of Attogram Quantities of Silver via Quenching of the Solid Substrate Room-Temperature Phosphorescence of Rhodamine B Based on the Catalysis of its Oxidation by Potassium Persulfate

A new method of SS-RTP for the determination of trace silver has been established. This method is based on the fact that Ag⁺, when activated by ,-bipyridyl (bipy) in a media of HAc–NaAc (pH=4.9), can catalyze the reaction of Rhodamine B (RhoB) oxidized by K₂S₂O₈, thus causing the Solid Substrate Room-Temperature Phosphorescence (SS-RTP) of RhoB to be quenched. The activating efficiency of bipy is 6.7 times higher than that of o-phenanthroline (phen). The reduction of the phosphorescence intensity (I_p) of RhoB is directly proportional to the concentration of Ag⁺ ions in the range of 1.6016.0agspot^–1 (0.40µLspot^–1). The regression equation of the working curve can be expressed as I_p=18.78+5.100m_Ag+ (agspot^–1) (r=0.9994, n=6), the detection limit is 0.28agspot^–1. This rapid, accurate and sensitive method has been successfully applied to the determination of trace silver in tea and human hair samples, and the results agree well with the Atomic Absorption Spectroscopy (AAS) method. The mechanism of the catalyzing reaction is also discussed.     

In-Situ Separation and Determination of Palladium from Platinum Based on Different Vaporization Temperatures by Electrothermal Vaporization Inductively Coupled Plasma Optical Emission Spectrometry with YPA4 Resin Acting Both as Adsorption Material and Chemical Modifier

A new method has been developed for in-situ separation of Pd from a Pt matrix and determination of trace Pd based on different vaporization temperatures by electrothermal vaporization (ETV) inductively coupled plasma optical emission spectrometry (ICP-OES) with the use of polythioether backbone modified with a diaminoisopropylmercaptane chelating group (YPA₄), both as solid phase extractant and chemical modifier. In 0.5M HNO₃, Pd and Pt can be adsorbed by YPA₄. The resin loaded with Pd and Pt was then prepared to form a slurry that can be directly introduced into the graphite furnace without any pretreatment. The factors affecting in-situ separation of Pd from the Pt matrix were investigated in detail. It was found that, in the presence of YPA₄, Pd could be quantitatively vaporized at lower vaporization temperatures (1800°C–1900°C), while Pt could not be vaporized from the graphite furnace at the same temperature, its quantitative vaporization temperature being 2600°C. Based on the different vaporization temperatures, in-situ separation of Pd from the Pt matrix and determination of trace Pd by ETV-ICP-OES was achieved in the temperature range of 1800°C–1900°C. Under the optimized conditions, the detection limit (3) of Pd is 60pg, and the relative standard deviation (RSD) is 5.6% (n=9, C=0.2µgmL^–1). The method has been applied to the determination of trace Pd in anode slime and Auto Catalyst NIST SRM 2557 reference material, and the determined values coincide with the certified values.     

Investigation of Medium Power Radiofrequency Capacitively Coupled Plasmas and Their Application to Atomic Emission Spectrometry for the Determination of Aluminium in Water Samples

A medium power radiofrequency capacitively coupled plasma (275W, 27.12MHz) with low argon consumption (0.5Lmin^–1) was investigated to be used for the determination of aluminium in water samples pneumatically nebulised by atomic emission spectrometry. The plasma torch was operated in two geometric configurations, coaxial and coaxial-annular with single (SRTr.f.CCP) or double ring electrodes (DRTr.f.CCP), respectively. The optimum experimental parameters (observation height, Ar flow rate, distance between ring electrodes, matrix interference of Na⁺ and Ca²⁺ and anion nature) for Al 396.152nm emission were established. Under optimum operating conditions of the DRTr.f.CCP torch (6cm distance between annular electrodes), a detection limit of 70ngmL^–1 aluminium was found. Both operating parameters and several figures of merit of the investigated plasmas were compared to those of microwave plasmas and inductively coupled plasma used in atomic emission spectrometry. The method was used to control the quality of drinking and industrial water. Samples were mineralised with 2mL of 1+1 HNO₃ and 10mL of 1+1 HCl. In the range of 0.15–3.5mgL^–1 Al³⁺ the relative standard deviation varied between 3.7 and 8.6% (n=3). For two certified drinking water samples containing 0.206 and 0.218mgL^–1 Al³⁺ the recovery (n=5) was 97.6±6.8% and 98.6±7.3%, respectively.     

Unambiguous Determination of the Absolute Configurations of Acetylene Alcohols by Combination of the <Emphasis Type="Italic">Sonogashira</Emphasis> Reaction and the CD Exciton Chirality Method – Exciton Coupling between Phenylacetylene and Benzoate Chromophores

Summary. The CD exciton chirality method was applied to various phenylacetylene alcohols to determine their absolute configurations; the long axis polarized –^* transition (_max=252nm) of the 4-methoxyphenylacetylene chromophore couples with the transition (_max=257nm) of the 4-methoxybenzoate group to generate intense exciton split CD Cotton effects, from the signs of which the absolute configurations of phenylacetylene alcohols were unambiguously determined. As an extension of the results, a new methodology for determining the absolute configurations of acetylene alcohols having the HCCCH(OH)-moiety by combination of the Sonogashira reaction and the CD exciton chirality method has been developed and applied. Since the –^* transition of acetylene triple bond is located below 180nm, it is difficult to observe ideal bisignate CD Cotton effects due to the exciton coupling between acetylene and benzoate chromophores. To observe the ideal exciton split Cotton effects necessary for the unambiguous determination of absolute configuration, the terminal acetylene group was converted, by the Sonogashira reaction, to the 4-methoxyphenylacetylene moiety, which exhibits an intense –^* absorption band polarized along the long axis of the chromophore at 252nm. As a partner of exciton coupling, 4-methoxybenzoate showing a –^* band at 257nm was introduced into the alcohol moiety, and the benzoates formed showed intense bisignate CD Cotton effects, from the signs of which the absolute configurations of original acetylene alcohols could be determined in an unambiguous manner.     

Determination of Heavy Metal Ions in Chinese Herbal Medicine by Microwave Digestion and RP-HPLC with UV-Vis Detection

A new method for the simultaneous determination of heavy metal ions in Chinese herbal medicine by microwave digestion and reversed-phase high-performance liquid chromatography (RP-HPLC) has been developed. The Chinese herbal medicine samples were digested by microwave digestion. Lead, cadmium, mercury, nickel, copper, zinc, and tin ions in the digested samples were pre-column derivatized with tetra-(4-chlorophenyl)-porphyrin (T₄-CPP) to form the colored chelates which were then enriched by solid phase extraction with C₁₈ cartridge and eluted from the cartridge with tetrahydrofuran (THF). The chelates were separated on a Waters Xterra RP₁₈ column by gradient elution with methanol (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) and THF (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) as mobile phase at a flow rate of 0.5mLmin^–1 and detected with a photodiode array detector in the range of 350–600nm. In the original samples the detection limits of lead, cadmium, mercury, nickel, copper, zinc and tin are 4ngL^–1, 3ngL^–1, 6ngL^–1, 5ngL^–1, 2ngL^–1, 6ngL^–1, and 4ngL^–1, respectively. This method was applied to the determination of lead, cadmium, mercury, nickel, copper, zinc and tin in Chinese herbal medicine samples with good results.     

Electrochemical Behavior of Epinephrine at a Penicillamine Self-Assembled Gold Electrode,and its Analytical Application

The fabrication and electrochemical characteristics of a penicillamine (PCA) self-assembled monolayer modified gold electrode were investigated. The self-assembled electrode shows obvious electrocatalytic activity for the oxidation of epinephrine (EP). In phosphate buffer (pH 7.73), a sensitive oxidation peak was observed at 0.190V with the PCA modified Au electrode. The peak current is proportional to the concentration of EP in the range of 2.0×10^–56.0×10^–4molL^–1 and 5.0×10^–6 2.0×10^–4molL^–1 for cyclic voltammetry (CV) and differential pulse voltammetry (DPV) with the detection limits of 1.8×10^–7 and 1.3×10^–7molL^–1, respectively. The possible reaction mechanism is also discussed. The PCA self-assembled monolayer modified gold electrode is highly stable and can be applied to the determination of EP in practical injection samples. Application is simple, rapid and produces accurate results.     

Photoluminescence of osmocene and decamethylosmocene

Osmocene (and decamethylosmocene) is characterized by a lowest-energy ligand field triplet which occurs at _max=372nm (374nm) in absorption and 567nm (572nm) in emission. This orange–yellow phosphorescence is rather intense at 77K but is also visible at r.t.     

Determination of Trace Iron in KH2PO4 Crystal by Derivative Adsorption Chronopotentiometry

A sensitive derivative adsorption chronopotentiometric method was developed to determine trace amounts of Fe³⁺. The influence of preconcentration time, pH of solution and constant reducing current of the peak height is discussed. The detection limit and the linear range are 5.0×10^–10 and 2.0×10^–93.0×10^–6molL^–1, respectively. The method was used to determine trace Fe³⁺ in KH₂PO₄ crystals (KDP).