Double perovskite oxides Sr_2Mg_(1-x)Fe_xMoO(6-δ) for catalytic oxidation of methane

The double perovskite oxides Sr2Mg1-xF exMoO6-δ were investigated as catalysts for the methane oxidation.The structural properties of catalysts were characterized in detail by X-ray diffraction,X-ray photoelectron spectroscopy and X-ray absorption spectroscopy.The catalytic property was strongly influenced by the Fe substitution.The relation between catalytic performance and the degree of Fe substitution was examined with regard to the structure and surface characteristics of the mixed oxides.The Fe-containing catalysts exhibited higher activity attributable to the possible(Fe2+,Mo6+) and (Fe3+,Mo5+)valency pairs,and the highest activity was observed for Sr2Mg0.2Fe0.8MoO6-δ.The enhancement of the catalytic activity may be correlated with the Fe-relating surface lattice oxygen species and was discussed in view of the presence of oxygen vacancies.     

CO2 Reforming of CH4 over Nickel and Cobalt Catalysts Prepared from La—Based Perovskite Precursors

Four perovskite-type complex oxides (LaNiO3, La2NiO4, LaCoO3 and La2CoO4) were successfully prepared using two sol-gel methods, the Pechini method (PC) and the citric acid complexing method (CC). The catalysts were characterized by XRD and TPR. After reduction, the activity of the catalysts in the CO2 reforming of methane was tested. Ni-based catalysts from La2NiO4 precursors were the most active and stable catalyst after calcination above 850 癈, which gave a methane conversion of 0.025 mmol/(g-s) for those prepared by the PC method and 0.020 mmol/(g-s) by the CC method. It was proposed that the well-defined structure and lower reducibility is responsible for the unusual catalytic behavior observed over the pre-reduced La2NiO4 catalyst.     

Complete Oxidation of Methane over Palladium Supported on Alumina Modified with Calcium,Lanthanum,and Cerium Ions

The activity and thermal stability of Pd/Al_2O_3 and Pd/(Al_2O_3 MO_x)(M=Ca,La,Ce) palladium catalysts in the reaction of complete oxidation of methane are presented in this study.The catalyst supports were prepared by sol-gel method and they were dried either conventionally or with supercritical carbon dioxide.Then they were impregnated with palladium nitrate solution.The catalysts with unmodified alumina had a high surface area.The activity and thermal stability of the alumina- supported catalyst was also very high.The introduction of calcium,lanthanum,or cerium oxide into alumina support caused a decrease of the surface area in the way dependent on the support precursor drying method.These modifiers decreased the activity of palladium catalysts,and they required higher temperatures for the complete oxidation of methane than unmodified Pd/Al_2O_3.The improvement of the palladium activity by lanthanum and cerium support modifier was observed only at low temperatures of the reaction.     

Catalytic Combustion of Methane over CO1-xMgxO/Al2O3/FeCrAl Monolithic Catalysts

A series of CoxMgxO/Al2O3/FeCrAl catalysts （x=0-1） were prepared. The structures of the catalysts were characterized using XRD, SEM, and TPR analyses. The catalytic activity of the catalysts for methane combustion was evaluated in a continuous flow microreactor. The results indicated that the active washcoats adhered well on the FeCrAl foils. The phases in the catalysts were Co--xMgxO solid solutions, α-Al2O3, and γ-Al2O3. The surface particle size of the catalysts varied with variations in the molar ratios of Co to Mg. The Co component of the Co1_xMgxO/Al2O3/FeCrAl catalysts played an important role in the catalytic activity for methane combustion. In the Co1-xMgxO/AluO3/FeCrAl series catalyst （x=0.2-0.8）, the catalytic activity in terms of x was in the order of 0.5〉0.2〉0.8 under the experimental conditions. The presence of Mg in these catalysts could promote the thermal stability to a large extent. There were strong interactions between the Co1-xMgxO oxides and the AluO3/FeCrAl supports.     

非负载和氧化铝负载的纳米CeO2-ZrO2和CeO2-We2O3固溶体催化CO氧化

Ceria-zirconia(CZ)and ceria-terbia(CT)and alumina-supported ceria-zirconia(CZA)and ceria-terbia(CTA)solid solutions were synthesized by coprecipitation and deposition precipitation methods,respectively.Structural characteristics and catalytic activity of the synthesized samples have been investigated using X-ray diffraction(XRD),high resolution transmission electron microscopy(HRTEM),X-ray photoelectron spectroscopy(XPS),Raman spectroscopy(RS),and Brunauer-Emmett-Teller(BET)surface area measurements.To evaluate the catalytic properties,total oxygen storage capacity and CO oxidation activity measurements were carried out.The XRD analyses revealed the formation of Ce0.75Zr0.25O2 phase for CZ and Ce0.5Zr0.5O2 and Ce0.6Zr0.4O2 phases for CZA samples,respectively.While the formation of only Ce0.8Tb0.2O2-δphase was noted for both CT and CTA samples.All the supported and unsupported samples adopted a fluorite-type structure and exhibited cell parameters with respect to Vegard’s rule.The HRTEM results indicated well-dispersed particles of the size around 5 nm.The RS measurements suggested the presence of oxygen vacancies due to defective structure formation.The XPS studies revealed the presence of cerium in both Ce 4+ and Ce 3+ oxidation states in different proportions.It was found that CO oxidation for CTA occurs at very much lower temperature than CT,CZ,and CZA samples.Details of these findings by correlating with the structural characterization studies are consolidated.     

溶胶-凝胶新方法合成介孔铁酸铜纳米粉体催化剂上CO低温氧化(英文)

Mesoporous CuFe2O4 solid solution nanopowders with high specific surface areas were synthesized by a novel, very simple and inexpensive sol-gel route using propylene oxide as gelation agent, and used as the catalyst in low temperature CO oxidation. The samples were characterized by X-ray diffraction, N2 adsorption-desorption, thermogravimetric/differential thermal analysis, Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, and temperature-programmed reduction. The results revealed that the samples have a nanocrystalline structure with crystals in the range of 10 to 25 nm, and that all the catalysts have mesoporous pores. The addition of Cu into iron oxide affected its structural and catalytic properties. The sample containing 15 mol% Cu showed the highest specific surface area and catalytic activity, and showed high catalytic stability in low temperature CO oxidation.     

Complete Oxidation of Methane Alumina Modified with Calcium, over Palladium Supported on Lanthanum, and Cerium Ions

The activity and thermal stability of Pd/Al2O3 and Pd/（Al2O3＋MOx） （M=Ca, La, Ce） palladium catalysts in the reaction of complete oxidation of methane are presented in this study. The catalyst supports were prepared by sol-gel method and they were dried either conventionally or with supercritical carbon dioxide. Then they were impregnated with palladium nitrate solution. The catalysts with unmodified alumina had a high surface area. The activity and thermal stability of the aluminasupported catalyst was also very high. The introduction of calcium, lanthanum, or cerium oxide into alumina support caused a decrease of the surface area in the way dependent on the support precursor drying method. These modifiers decreased the activity of palladium catalysts, and they required higher temperatures for the complete oxidation of methane than unmodified Pd/Al2O3. The improvement of the palladium activity by lanthanum and cerium support modifier was observed only at low temperatures of the reaction.     

Simultaneous removal of ethanol, acetaldehyde and nitrogen oxides over V-Pd/γ-Al_2O_3-TiO_2 catalyst

V-Pd/γ-Al2O3-TiO2 catalysts with different vanadium contents were prepared by a combined sol-gel and impregnation method. X-ray diffraction (XRD), N2 adsorption-desorption (BET), X-ray photoelectron spectroscopy (XPS) and catalytic removal of ethanol, acetaldehyde and nitrogen oxides at low temperature (<300 ?C) were used to assess the properties of the catalysts. The results showed that the sample with 1wt% vanadium exhibited an excellent catalytic performance for simultaneous removal of ethanol, acetaldehyde and nitrogen oxides. The conversions of ethanol, acetaldehyde and nitrogen oxides at 250 ?C were 100%, 74.4% and 98.7%, respectively. V-Pd/γ-Al2O3-TiO2 catalyst with 1 wt% vanadium showed the largest surface area and higher dispersion of vanadium oxide on the catalyst surface, and possessed a larger mole fraction of V4+ species and unique PdO species on the surface, which can be attributed to the strong synergistic effect among palladium, vanadium and the carriers. The higher activity of V-Pd/γ-Al2O3-TiO2 catalyst is related to the V4+ and Pd2+ species on the surface, which might be favorable for the formation of active sites.     

Effects of ultrasonic impregnation combined with calcination in N_2 atmosphere on the property of Co_3O_4/CeO_2 composites for catalytic methane combustion

Co_3O_4/CeO_2 composites with high surface areas and ultrafine crystalline sizes for catalytic combustion of methane were firstly prepared by a new sol-gel method which combined ultrasonic impregnation treatment and calcination in N_2 atmosphere. The samples were characterized by various means such as nitrogen adsorption/desorption, X-ray diffraction(XRD), H_2 temperature-programmed reduction(H_2-TPR),X-ray photoelectron spectroscopy(XPS) and transmission electron microscopy(TEM). Results showed that the modified catalyst had the mesoporous structure, comparatively higher amount of surface oxygen and larger oxygen vacancies than others. As a result of the structure and surface composition merits, a high methane combustion conversion(50%) could be obtained at a low temperature of 262 °C for the modified Co_3O_4/CeO_2 composites catalysts. The experimental results demonstrated that ultrasonic impregnation treatment combined with the N_2 thermal treatment prior to calcination in air had a promising application for preparation of Co_3O_4/CeO_2 composites catalysts for low-temperature catalytic combustion of methane.     

Catalytic Combustion of Methane over High Copper-Loading ZSM-5 Catalysts

Two series of Cu/ZSM-5 catalysts,loading from 5 to 20 wt% CuO,were prepared by the deposition-precipitation and impregnation methods,respectively.The catalysts prepared by the impreg- nation method showed better catalytic performances than those prepared by the deposition-precipitation method and the increase of copper loading favored methane conversion.20Cu(I)/ZSM-5 had the highest activity with T_(90%)of 746 K,and for 20Cu(D)/ZSM-5,T_(90%)was as high as 804 K.The characteriza- tion of X-ray diffraction(XRD),temperature-programmed reduction(TPR),temperature-programmed desorption(TPD),and X-ray photoelectron spectroscopy(XPS)revealed that the dispersion of cop- per species could be improved by using the deposition-precipitation method instead of the impregnation method,but the fraction of surface CuO,corresponding to active sites for methane oxidation,was larger on 20Cu(I)/ZSM-5 than 20Cu(D)/ZSM-5.The results of Pyridine-Fourier transform infrared spectrum (Py-FT-IR)showed that a majority of Lewis acidity and a minority of Brφnsted acidity were present on Cu/ZSM-5 catalysts.20Cu(I)/ZSM-5 presented more Lewis acid sites.The number of Lewis acid sites changed significantly with preadsorption of oxygen.Adsorption of methane and oxygen on acid sites was observed.The properties of Cu/ZSM-5 catalysts were correlated with the activity for methane oxidation.     

纳米La0.8A’0.2Mn1-xCuxO3（A’=Ce and/or Sr）的制备、表征及其高效催化NO+CO的性能研究

采用柠檬酸-溶胶凝胶法制得钙钛矿型复合氧化物La0.8Ce0.2Mn1-xCuxO3(x=0.2,0.3,0.4),La0.8Sr0.2Mn0.6Cu0.4O3,La0.8Ce0.1Sr0.1Mn0.6 Cu0.4 O3,并采用X射线衍射(XRD)、扫描电镜(SEM)、比表面积(BET)、X射线光电子能谱(XPS)对其进行表征,测试了复合氧化物对CO+NO的催化活性。结果表明:La0.8Ce0.1Sr0.1Mn0.6Cu0.4O3催化活性最好,150℃时CO转化率91.8%,300℃时NO转化率100%;对于La0.8Ce0.2Mn1-xCuxO3(x=0.2,0.3,0.4),比表面积和颗粒的大小及分散度是影响催化活性的主要因素;对于La0.8Ce0.2Mn0.6Cu0.4O3,La0.8 Sr0.2 Mn0.6 Cu0.4 O3,La0.8 Ce0.1 Sr0.1 Mn0.6 Cu0.4 O3,催化剂的组成是影响催化活性的关键因素。     

CeO2-TiO2复合氧化物的制备、表征及其对CO氧化的催化性能

采用溶胶-凝胶法制备了一系列不同n(Ce)/n(Ti)的CeO2-TiO2复合氧化物,对复合氧化物的物相结构、形貌特征、比表面积和氧化还原性质进行了表征,并考察了复合氧化物对CO氧化反应的催化性能.结果表明,n(Ce)/n(Ti)>0.10时,复合氧化物为无定形结构;n(Ce)/n(Ti)=0.10~0.30时,复合氧化物失去CeO2和TiO2各自的特征,形成CeO2-TiO2固溶体,具有较大的比表面积.CeO2-TiO2复合氧化物本身对CO氧化反应的催化活性不如TiO2或CeO2的高,但Pd/CeO2-TiO2比Pd/TiO2或Pd/CeO2具有更高的催化活性.     

La-Ni-Al钙钛矿氧化物中Sr和Ca取代La对甲醇重整的影响

Mixed perovskite oxides with CaxLa1-xNi0.3Al0.7O3-d and SrxLa1-xNi0.3Al0.7O3-d(x=0,0.2,0.5,0.8,and 1.0;d=0.5x)components have been prepared by a sol-gel method.The effects of the partial substitution of La by Ca and Sr in dry CH4 reforming were investigated at 500-800 ℃ and 101 kPa.The resulting oxides were examined by Fourier-transform infrared spectroscopy,X-ray diffraction,temperature-programmed reduction,scanning electron microscopy,energy dispersive X-ray spectrometry,and BET surface area analysis.Studies following the catalytic tests by carbon analysis show some carbon deposition on this catalytic system.The results indicate that all initial salt entered into a propionate structure,and that most of the solid solution has well defined perovskite structure with surface areas between 3.5 and 9.5 m2/g.Most of the catalysts performed well in the dry reforming,with CH4 conversions up to 90%,H2 yields up to 80%,and H2 selectivity up to 90%.Among the samples,Sr0.2La0.8Ni0.3Al0.7O2.9 showed an excellent catalytic performance in CH4 dry reforming,with a H2/CO ratio of 1,whereas Ca0.8La0.2Ni0.3Al0.7O2.6 showed the lowest coke formation(approximately 0.71%).     

La_2NiBO_6催化剂的制备及其对甲烷燃烧反应的催化性能

以柠檬酸为络合剂,采用溶胶-凝胶法制备了一系列双钙钛矿型催化剂La_2NiBO_6(B=Mn,Fe,Co,Cu,Ce),其结构经SEM,XRD,N2-BET和H2-TPR表征。以甲烷燃烧反应为模板反应,研究了La_2NiBO_6的催化性能。结果表明:La_2NiCeO_6催化性能最好,起燃温度T_(10%)为461℃,最终转化温度T_(90%)为565℃。     

Samarium Based High Surface Area Perovskite Type Oxides SmFe1-XAlXO3 (X=0.00, 0.50, 0.95). Part II, Catalytic Combustion of CH4

The catalytic combustion of methane with stoichiometric amounts of oxygen to CO₂ and H₂O has been studied over samarium based high surface area perovskite type oxides SmFe_1-xAl_xO₃ (x=0.00, 0.50 0.95) prepared via a new sol-gel method. A comparison to other lanthanum perovskites prepared by the ceramic method shows higher catalytic activity for SmFeO₃ and SmFe_0.5Al_0.5O₃ samples.     

LaMO3纳米复合钙钛矿氧载体化学循环重整甲烷制合成气

采用溶胶-凝胶法制备了不同B位可变价离子的LaMO3 (M= Cr,Mn,Fe,Co)复合氧化物氧载体,采用X射线衍射、N2吸附-脱附、扫描电镜及CH4程序升温表面反应等手段对氧载体进行了表征,并用于直接选择氧化CH4的反应中.结果表明,Cr,Mn,Fe 和Co均能形成LaMO3纳米复合钙钛矿结构,其氧物种氧化能力大小...     

Effect of Partial Substitution of Ni by Cu in LaNiO3 Perovskite Catalyst for Dry Methane Reforming

A series of ternary perovskite type oxides LaNi1-xCuxO3(x = 0.2,0.4,0.6,0.8,and 1.0) were synthesized via the sol-gel method in propionic acid.Partial substitution of Ni by Cu showed higher activities and selectivities towards syngas products.LaNi0.8Cu0.2O3 was the most active toward the CH4 and CO2 conversions,and was selective for syngas products.Temperature-programmed reduction results showed that the addition of Cu facilitates the reduction of Ni3+ to Ni0,which is the main reason for the higher performance of this catalyst.     

Methane reforming With CO2 to syngas over CeO2-promoted Ni/Al2O3-ZrO2 catalysts Prepared Via a direct sol-gel process

CeO2-promoted Ni/Al2O3-ZrO2 (Ni/Al2O3-ZrO2-CeO2) catalysts were prepared by a direct sol-gel process with citric acid as gelling agent. The catalysts used for the methane reforming with CO2 was studied by infrared spectroscopy (IR), thermal gravimetric analysis (TGA), microscopic analysis, X-ray diffraction (XRD) and temperature-programmed reduction (TPR). The catalytic performance for CO2 reforming of methane to synthesis gas was investigated in a continuous-flow micro-reactor under atmospheric pressure. TGA, IR, XRD and microscopic analysis show that the catalysts prepared by the direct sol-gel process consist of Ni particles with a nanostructure of around 5 nm and an amorphous-phase composite oxide support. There exists a chemical interaction between metallic Ni particles and supports, which makes metallic Ni well dispersed, highly active and stable. The addition of CeO2 effectively improves the dispersion and the stability of Ni particles of the prepared catalysts, and enhances the adsorption of CO2 on the surface of catalysts. The catalytic tests for methane reforming with CO2 to synthesis gas show that the Ni/Al2O3-ZrO2-CeO2 catalysts show excellent activity and stability compared with the Ni/Al2O3 catalyst. The excellent catalytic activity and stability of the Ni/Al2O3-ZrO2-CeO2 are attributed to the highly, uniformly and stably dispersed small metallic Ni particles, the high reducibility of the Ni oxides and the interaction between metallic Ni particles and the composite oxide supports.