A new modified conducting carbon composite electrode as sensor for ascorbate and biosensor for glucose

A new carbon-based conducting composite has been developed as electrochemical sensor and biosensor for the amperometric detection of ascorbate and glucose. Electrocatalytic oxidation of ascorbate has been done successfully at unmodified cellulose acetate-graphite composite electrodes, the sensor being highly sensitive, selective and with a low detection limit at 0.0 V vs. SCE and was successfully applied for ascorbate determination in commercial fruit juice samples. An interference free glucose biosensor has also been developed, based on the immobilisation of glucose oxidase by cross-linking with glutaraldehyde on poly (neutral red) modified composite electrodes. The biosensor exhibits a higher sensitivity of 31.5 ± 1.7 µA cm^− 2 mM^− 1 than other carbon-composite-based glucose biosensors, a detection limit of 20.3 µM and a very short response time.     

Amperometric glucose biosensor based on a gold nanorods/cellulose acetate composite film as immobilization matrix

We report on the utilization of gold nanorods to create a highly responsive glucose biosensor. The feasibility of an amperometric glucose biosensor based on immobilization of glucose oxidase (GOx) in gold nanorod is investigated. GOx is simply mixed with gold nanorods and cross-linked with a cellulose acetate (CA) medium by glutaraldehyde. The adsorption of GOx on the gold nanorods is confirmed by X-ray photoelectron spectroscopy (XPS) measurements. Circular dichroism (CD) and UV-spectrum results show that the activity of GOx was preserved after conjugating with gold nanorods. The current response of modified electrode is 10 times higher than that of without gold nanorods. Under optimal conditions, the biosensor shows high sensitivity (8.4 μA cm⁻² mM⁻¹), low detection limit (2 × 10⁻⁵ M), good storage stability and high affinity to glucose (). A linear calibration plot is obtained in the wide concentration range from 3 × 10⁻⁵ to 2.2 × 10⁻³ M.     

Porous cuprous oxide microcubes for non-enzymatic amperometric hydrogen peroxide and glucose sensing

Using porous cuprous oxide (Cu₂O) microcubes, a simple non-enzymatic amperometric sensor for the detection of H₂O₂ and glucose has been fabricated. Cyclic voltammetry (CV) revealed that porous Cu₂O microcubes exhibited a direct electrocatalytic activity for the reduction of H₂O₂ in phosphate buffer solution and the oxidation of glucose in an alkaline medium. The non-enzymatic amperometric sensor used in the detection of H₂O₂ with detection limit of 1.5 × 10^?6 M over wide linear detection ranges up to 1.5 mM and with a high sensitivity of 50.6 μA/mM. This non-enzymatic voltammetric sensor was further utilized in detection of glucose with a detection limit of 8.0 × 10^?7 M, a linear detection range up to 500 μM and with a sensitivity of ?70.8 μA/mM.     

Nonenzymatic electrochemical glucose sensor based on MnO2/MWNTs nanocomposite

In this communication, an amperometric glucose biosensor based on MnO₂/MWNTs electrode was reported. MnO₂ was homogeneously coated on vertically aligned MWNTs by electrodeposition. The MnO₂/MWNTs electrode displayed high electrocatalytic activity towards the oxidation of glucose in alkaline solution, showing about 0.30 V negative shift in peak potential with oxidation starting at ca. −0.20 V (vs. 3 M KCl–Ag/AgCl) as compared with bare MWNTs electrode. At an applied potential of +0.30 V, the MnO₂/MWNTs electrode gives a linear dependence (R = 0.995) in the glucose concentration up to 28 mM with a sensitivity of 33.19 μA mM⁻¹. Meanwhile, the MnO₂/MWNTs electrode is also highly resistant toward poisoning by chloride ions. In addition, interference from the oxidation of common interfering species such as ascorbic acid, dopamine, and uric acid is effectively avoided. The MnO₂/MWNTs electrode allows highly sensitive, low-potential, stable, and fast amperometric sensing of glucose, which is promising for the development of nonenzymatic glucose sensor.     

Mesoporous MnO2 as enzyme immobilization host for amperometric glucose biosensor construction

Mesoporous MnO₂ (mesoMnO₂) is synthesized facilely through sol–gel process using nonionic surfactant polyxyethylene fatty alcohol (AEO₉) as template. Transmission electron microscopy (TEM) image and N₂ adsorption/desorption isotherm show that the obtained mesoMnO₂ material presents disordered porous structure and appropriate pore size suitable for the immobilization of glucose oxidase (GOx). An amperometric glucose biosensor based on GOx entrapped in mesoMnO₂ is fabricated, in which mesoMnO₂ also acts as a catalyst for the electrochemical oxidation of H₂O₂ produced by enzyme reaction. The biosensor shows fast and sensitive current response to glucose in the linear range of 0.0009–2.73 mM. The response time (t_95%) is less than 7 s. The sensitivity and detection limit are 24.2 μA cm⁻² mM⁻¹ and 1.8 × 10⁻⁷ M (S/N = 3), respectively. This indicates that mesoMnO₂ has promising application in enzyme immobilization and biosensor construction.     

A new hydrogen peroxide biosensor based on gold nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film-modified electrode

Gold nanoelectrode ensembles were produced by electrodeposition using multiwalled carbon nanotubes (MWNTs) as template. A new third generation amperometric biosensor for hydrogen peroxide was developed based on adsorption of horseradish peroxidase (HRP) at the glassy carbon (GC) electrode modified with Au nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film. The resulting HRP biosensor offered an excellent detection for hydrogen peroxide at −0.11 V with a linear response range of 2.08 × 10⁻⁷ to 7.6 × 10⁻³ M with a correlation coefficient of 0.998, and response time <5 s. The detection limit was 1.02 × 10⁻⁷ M at 3σ. The biosensor displays rapid response, expanded linear response range, and excellent repeatability. The simple and fast fabrication of the sensor makes it superior to other techniques.     

毛细管电泳-安培法测定复方磺胺甲噁唑片中的有效成分

采用毛细管电泳-安培法(CE-AD)同时分离测定了磺胺甲噁唑(sulfamethoxazole,SMZ)、磺胺嘧啶(sulfadiazine,SD)和抗菌增效剂甲氧苄胺嘧啶(trimethoprim,TMP)3种常用磺胺类抗菌药物成分,考察了实验参数对分离、检测体系的影响。在优化实验条件下,以300μm碳圆盘电极作为工作电极,检测电位为1050mV(vs.SCE),在Na2B4O7(13mmol/L)-KH2PO4(18mmol/L)(pH5.8)的缓冲溶液中,分离电压18kV,进样6s,3组分在14min内可实现基线分离。上述3组分浓度分别在5×10-4~5×10-2、5×10-4~0.1和5×10-4~5×10-2g/L范围内与其峰电流强度呈线性关系,检出限达5.1×10-5~8.0×10-5g/L(S/N=3)。该方法已成功应用于复方磺胺甲噁唑片中抗菌活性成分的含量测定,结果令人满意。     

C60 trianion-mediated electrocatalysis and amperometric sensing of hydrogen peroxide

Heterogeneous electrocatalytic reduction of hydrogen peroxide (H₂O₂) by C₆₀ is reported for the first time. C₆₀ is embedded in tetraoctylammonium bromide (TOAB) film and is characterized by scanning electron microscopy and cyclic voltammetry. Electrocatalytic studies show that the trianion of C₆₀ mediates the electrocatalytic reduction of H₂O₂ in aqueous solution containing 0.1 M KCl. Application of such film modified electrode as an amperometric sensor for H₂O₂ determination is also examined. The sensor shows a fast response within 1 s and a linear response is obtained (R = 0.9986) in the concentration range from 3.33 × 10⁻⁵ to 2.05 × 10⁻³ mol L⁻¹ for H₂O₂, with the detection limit of 2 × 10⁻⁵ mol L⁻¹ and the sensitivity of 1.65 μA mM⁻¹. A good repeatability and stability is shown for the sensor during the experiment.     

Separation and determination of l-tyrosine and its metabolites by capillary zone electrophoresis with a wall-jet amperometric detection

A method of capillary electrophoresis with wall-jet amperometric detection (AD) has been developed for separation and determination of l-tyrosine (Tyr) and its metabolites, such as Tyramine (TA), p-hydroxyphenylpyruvic (pHPP), homogentisic acid (HGA) and some dipeptides containing Tyr, such as Tyr-Gly-Gly (YGG), Tyr-Arg (YR) and Tyr-d-Arg (Y-d-R). A carbon disk electrode was used as the working electrode and the optimal detection potential was 1.00 V (versus Ag/AgCl). At 18 kV of applied voltage, the seven compounds were completely separated within 20 min in 110 × 10⁻³ mol/L Na₂HPO₄–NaH₂PO₄ buffer (pH 7.10) containing 3 × 10⁻³ mol/L β-cyclodextrin (β-CD). Good linear relationship was obtained for all analytes and the detection limits of seven analytes were in the range of 0.95–4.25 ng/mL. The proposed method has been applied to examine the metabolic process of l-tyrosine in rabbit's urine.     

Palladized aluminum electrode covered by Prussian blue film as an effective transducer for electrocatalytic oxidation and hydrodynamic amperometry of N-acetyl-cysteine and glutathione

The mediated oxidation of N-acetyl cysteine (NAC) and glutathione (GL) at the palladized aluminum electrode modified by Prussian blue film (PB/Pd–Al) is described. The catalytic activity of PB/Pd–Al was explored in terms of Fe^III[Fe^III(CN)₆]/Fe^III[Fe^II(CN)₆]¹⁻ system by taking advantage of the metallic palladium layer inserted between PB film and Al, as an electron-transfer bridge. The best mediated oxidation of NAC and GL on the PB/Pd–Al electrode was achieved in 0.5 M KNO₃ + 0.2 M potassium acetate of pH 2. The mechanism and kinetics of the catalytic oxidation reactions of the both compounds were monitored by cyclic voltammetry and chronoamperometry. The charge transfer-rate limiting step as well as overall oxidation reaction of NAC or GL is found to be a one-electron abstraction. The values of transfer coefficients α, catalytic rate constant k and diffusion coefficient D are 0.5, 3.2 × 10² M⁻¹ s⁻¹ and 2.45 × 10⁻⁵ cm² s⁻¹ for NAC and 0.5, 2.1 × 10² M⁻¹ s⁻¹ and 3.7 × 10⁻⁵ cm² s⁻¹ for GL, respectively. The modifying layers on the Pd–Al substrate have reproducible behavior and a high level of stability in the electrolyte solutions. The modified electrode is exploited for hydrodynamic amperometry of NAC and GL. The amperometric calibration graph is linear in concentration ranges 2 × 10⁻⁶–40 × 10⁻⁶ for NAC and 5 × 10⁻⁷–18 × 10⁻⁶ M for GL and the detection limits are 5.4 × 10⁻⁷ and 4.6 × 10⁻⁷ M, respectively.     

Development of an amperometric biosensor based on covalent immobilization of tyrosinase on a boron-doped diamond electrode

An amperometric enzyme electrode based on direct covalent immobilization of tyrosinase on a boron-doped diamond (BDD) electrode has been developed for the detection of phenolic compounds. Combined chemical and electrochemical modifications of the BDD film with 4-nitrobenzenediazonium tetrafluoroborate, an aminophenyl-modified BDD (AP–BDD) surface was produced, and then the tyrosinase was covalently immobilized on the BDD surface via carbodiimide coupling. The response dependences of the enzyme electrode (Tyr–AP–BDD electrode) on pH of solution, applied potential, oxygen level and phenolic compounds diffusion were studied. The Tyr–AP–BDD electrode shows a linear response range of 1–200, 1–200 and 1–250 μM and sensitivity of 232.5, 636.7 and 385.8 mA M⁻¹ cm⁻² for phenol, p-cresol and 4-chlorophenol, respectively. 90 percent of the enzyme activity of the Tyr–AP–BDD electrode is retained for 5 weeks storing in 0.1 M PBS (pH 6.5) at 4 °C.     

Simultaneous determination of flavonoids in chrysanthemum by capillary zone electrophoresis with running buffer modifiers

Despite the separation efficiency of capillary electrophoresis (CE) is much higher than other chromatographic methods, it is sometimes difficult to perfectly separate the complex ingredients in biological samples. One possible and simple way to develop the separation effect in CE is to add some modifiers in the running buffer. In this paper, the suitable running buffer modifiers were explored to simultaneously separate and detect six typical flavonoids (apigenin, luteolin, kaempferol, quercetin, (+)-catechin and (−)-epicatechin) which are the main active ingredients in chrysanthemum by capillary zone electrophoresis with amperometric detection (CZE-AD). It was found that when β-cyclodextrin (β-CD) and the mixture of methanol and ethanol were used as running buffer modifiers, a baseline separation of the six analytes could be accomplished in less than 20 min and the detection limits were as low as 10⁻⁷ or 10⁻⁸ g ml⁻¹. Other factors affecting the CZE separation, such as working potential, pH value and ionic strength of running buffer, separation voltage and sample injection time were extensively investigated. Under the optimum conditions, a successful practical application on the determination of chrysanthemum samples confirmed the validity and practicability of this method.     

Chitosan–iron oxide nanobiocomposite based immunosensor for ochratoxin-A

The rabbit immunoglobulin antibodies (IgGs) have been immobilized onto nanobiocomposite film of chitosan (CH)–iron oxide (Fe₃O₄₎ nanoparticles prepared onto indium–tin oxide (ITO) electrode for detection of ochratoxin-A (OTA). Excellent film forming ability and availability of –NH₂ group in CH and affinity of surface charged Fe₃O₄ nanoparticles for oxygen support the immobilization of IgGs. Differential pulse voltammettry (DPV) studies indicate that Fe₃O₄ nanoparticles provide increased electroactive surface area for loading of IgGs and improved electron transport between IgGs and electrode. IgGs/CH–Fe₃O₄ nanobiocomposite/ITO immunoelectrode exhibits improved characteristics such as low detection limit (0.5 ng dL⁻¹), fast response time (18 s) and high sensitivity (36 μA/ng dL⁻¹ cm⁻²) with respect to IgGs/CH/ITO immunoelectrode.     

Studies on the kinetics of ascorbate oxidation at a ruthenium oxide hexacyanoferrate modified electrode towards the detection at microenvironments

The electrocatalytic oxidation of ascorbate on a ruthenium oxide hexacyanoferrate (RuOHCF) glassy carbon (GC) modified electrode was investigated at pH 6.9 by using rotating disc electrode (RDE) voltammetry. The influence of the systematic variation of rotation rate, film thickness, ascorbate concentration and the electrode potential indicated that the rate of cross-chemical reaction between Ru(III) centres immobilized into the film and ascorbate controls the overall process. The kinetic regime may be classified as a Sk″ mechanism and the second order rate constant for the surface electrocatalytic reaction was found to be 1.56 × 10⁻³ mol⁻¹ L¹ s⁻¹ cm. A carbon fibre microelectrode modified with the RuOHCF film was successfully used as an amperometric sensor to monitor the ascorbate diffusion in a simulated microenvironment experiment.     

Determination of photoirradiated high polar benzoylureas in tomato by HPLC with luminol chemiluminescence detection

This study reports the first analytical application of luminol chemiluminescence reaction for the sensitive detection of two benzoylurea insecticides (diflubenzuron and triflumuron). Off-line experiments demonstrated that previously irradiated traces of these benzoylurea insecticides largely enhanced the chemiluminescence emission yielded from the oxidation of luminol in methanol:water mixtures, by potassium permanganate in alkaline medium, the enhancement being proportional to the concentration of both pesticides. The two benzoylureas were determined in tomato samples by coupling liquid chromatography with post-column photoderivatization and detection based on this chemiluminescence reaction. Tomato samples were extracted using the QuEChERS method based on extraction with acetonitrile and dispersive solid-phase clean-up using primary and secondary amine (PSA). Interferences due to matrix effect were overcome by using matrix-matched standards. The optimised method was validated with respect to linearity, limits of detection and quantification, precision and accuracy. Under the optimised conditions, calibrations graphs were linear between 0.05 and 0.50 μg mL⁻¹ for diflubenzuron and between 0.10 and 1.00 μg mL⁻¹ for triflumuron. Method detection limits were 0.0025 and 0.0131 μg mL⁻¹ (equivalent to 0.0005 and 0.0026 mg kg⁻¹) and quantification limits were 0.05 and 0.10 μg mL⁻¹ (equivalent to 0.01 and 0.02 mg kg⁻¹) for diflubenzuron and triflumuron, respectively. In both cases, quantification limits were lower than the maximum residue levels (MRLs) established by the European legislation. The relative standard deviation of intra-day precision was below 10% and recoveries were between 79.7% and 94.2% for both pesticides.     

Bulk-modified modified screen-printing carbon electrodes with both lactate oxidase (LOD) and horseradish peroxide (HRP) for the determination of L-lactate in flow injection analysis mode

A screen-printed carbon electrode modified with both HRP and LOD (SPCE–HRP/LOD) has been developed for the determination of l-lactate concentration in real samples. The resulting SPCE–HRP/LOD was prepared in a one-step procedure, and was then optimised as an amperometric biosensor operating at [0, −100] mV versus Ag/AgCl for l-lactate determination in flow injection mode. A significant improvement in the reproducibility (coefficient variation of about 10%) of the preparation of the biosensors was obtained when graphite powder was modified with LOD in the presence of HRP previously oxidised by periodate ion (IO₄⁻). Optimisation studies were performed by examining the effects of LOD loading, periodation step and rate of the binder on analytical performances of SPCE–HRP/LOD. The sensitivity of the optimised SPCE–HRP/LOD to l-lactate was 0.84 nA L μmol⁻¹ in a detection range between 10 and 180 μMol. The possibility of using the developed biosensor to determine l-lactate concentrations in various dairy products was also evaluated.     

Spectrofluorimetric quantification of bromazepam using a highly selective optical probe based on Eu–bromazepam complex in pharmaceutical and serum samples

A rapid, simple and sensitive spectrofluorimetric method for determination of trace amount of bromazepam is developed. In phosphate buffer of pH 7.4. The bromazepam enhance the luminescence intensity of the Eu³⁺ ion in Eu³⁺–bromazepam complex at λ_ex = 390 nm. The produced luminescence intensity of Eu³⁺–bromazepam complex is in proportion to the concentration of bromazepam. The working range for the determination of bromazepam is 2.3 × 10⁻⁸ to 6.2 × 10⁻⁷ M with detection limit (LoD) and quantitative detection limit (LoQ) of 3 × 10⁻⁹ and 1.2 × 10⁻⁸ M, respectively. While, the working range, detection limit (LoD) and quantitative detection limit (LoQ) in case of the quantum yield calculations are 3.7 × 10⁻⁸ to 3.4 × 10⁻⁷ M with of 3.4 × 10⁻⁹ and 9.2 × 10⁻⁸ M, respectively. The enhancement mechanism of the luminescence intensity in the Eu³⁺–bromazepam system has been also explained.     

Direct electrochemistry of glucose oxidase based on its direct immobilization on carbon ionic liquid electrode and glucose sensing

Direct electrochemistry of glucose oxidase (GOx) has been achieved by its direct immobilization on carbon ionic liquid electrode (CILE) with a conductive hydrophobic ionic liquid, 1-butyl pyridinium hexafluophosphate ([BuPy][PF₆]) as binder for the first time. A pair of reversible peaks is exhibited on GOx/CILE by cyclic voltammetry. The peak-to-peak potential separation (ΔE_P) of immobilized GOx is 0.056 V in 0.067 M phosphate buffer solution (pH 6.98) with scan rate of 0.1 V/s. The average surface coverage and the apparent Michaelis–Menten constant are 6.69 × 10⁻¹¹ mol·cm⁻² and 2.47 μM. GOx/CILE shows excellent electrocatalytic activity towards glucose determination in the range of 0.1–800 μM with detection limit of 0.03 μM (S/N = 3). The biosensor has been successfully applied to the determination of glucose in human plasma with the average recoveries between 95.0% and 102.5% for three times determination. The direct electrochemistry of GOx on CILE is achieved without the help of any supporting film or any electron mediator. GOx/CILE is inexpensive, stable, repeatable and easy to be fabricated.     

Tyrosinase/laccase bienzyme biosensor for amperometric determination of phenolic compounds

Tyrosinase/laccase bienzyme biosensor for amperometric determination of phenolic compounds was constructed. Enzymes were immobilized in titania gel matrix. The obtained biosensor was successfully used for determination of 2,6-dimethoxyphenol, 4-tertbutylcatechol, 4-methylcatechol, 3-chlorophenol and catechol. The highest sensitivity and the widest linear range were noticed for catechol, 234 mA L mol^− 1 and 2.0 × 10^− 7–3.2 × 10^− 5 mol/L, respectively. Detection limit for catechol, at signal-to-noise ratio of 3 was 1.3 × 10^− 7 mol/L.     

Gold nanoparticles integrated in a nanotube array for electrochemical detection of glucose

An enzyme-free amperometric glucose sensor of gold nanoparticle-constituted nanotube array electrode is presented. The resulted gold nanotube array electrode with significantly enhanced surface roughness shows prominent catalytic activity toward the electrooxidation of glucose in a pH 7.4 phosphate buffer (PBS) solution and thus can be used to individually or simultaneously determine glucose and the common interfering molecule of ascorbic acid (AA). In the case of glucose detection, the amperometric responses show a linear relationship to glucose concentration in the range of 1 mM–42.5 mM with a detection limit down to 10 μM. The present non-enzymatic glucose electrochemical biosensor shows a good stability and reproducibility.