全固双层芯色散补偿光子晶体光纤的研究与设计

为了补偿光纤色散对高速信号传输的限制,提出一种全固双层芯色散补偿光子晶体光纤.首先对该光纤模式耦合特性进行理论分析,然后利用多极法进行模拟计算,得到该光纤包层结构参数与色散值以及相位匹配波长之间的关系,并对其规律进行研究.通过优化光纤结构参数,得到在1 550nm处,色散值达到-32 620ps/(nm·km)、损耗为0.29dB/km、与标准单模光纤的熔接损耗为4.77dB的色散补偿光纤.该光纤可补偿1 910多倍长度的SMF-28单模光纤的色散,补偿能力远大于常规色散补偿光纤.与空气孔-石英结构色散补偿光子晶体光纤相比,全固色散补偿光子晶体光纤具有易制备、易与传统通信光纤熔接等优点.     

负色散斜率的色散补偿光纤的研制

对三包层的大负色散、负色散斜率的色散补偿光纤进行了理论研究，分析了各个参量对色散曲线的调节作用，发现色散补偿光纤只有在一定范围的拉丝芯径内，以牺牲负色散数值才能大负色散斜率，采用在光纤拉丝时旋转预制棒的工艺减小了光纤的偏振模色散进一步改进国内已有的的改进的化学汽相沉积（ＭＣＶＤ）光纤生产工艺，研制出了较高水平的色散补偿光纤。     

光纤光栅耦合系数对其色散补偿性能的影响

本文利用耦合模方程,对具有不同函数形状耦合系数的光纤光栅的色散特性进行了理论和数值研究。通过比较这些线性咽啾光纤光栅对10Gb/s光通信系统色散补偿的效果,揭示了光纤光栅的耦合系数与其色散补偿性能的关系。     

一种新的低非线性宽带色散补偿微结构光纤的设计

采用矢量光束传输法对空气孔包层呈正六边形分布的微结构光纤的色散和非线性特性进行了数值模拟。通过分别调节内三层空气孔的直径和包层空气孔节距,设计了一种低非线性宽带色散补偿微结构光纤。该光纤在波长1.55 μm处具有－3 235.8 ps/nm/km的大负色散,可在以1.55 μm为中心的100 nm宽带波长范围对相当于自身长度190倍的普通单模传输光纤进行宽带色散补偿(色散补偿率偏移在0.5%以内),同时该光纤可在此宽带波长范围内保持非线性系数低于5 W^-1·km^-1。     

Optical Fiber Impulse Propagation: An Interaction Between the Third-Order Dispersion and Nonlinear Chirp

This article investigates the interaction between the third-order dispersion in optical fiber and the nonlinear (quadratic) chirp of Gaussian impulses. A formula is obtained for the impulse form at the fiber far end. The impulse propagation in nonlinear fiber is also examined by means of a computer simulation. The obtained results indicate that the interaction may lead to significant distortion of optical impulses at the fiber output even when the second-order dispersion is entirely canceled and the input impulse has no linear chirp. This distortion is more pronounced when the dispersion slope, fiber length, and nonlinear chirp parameter increase.     

通信系统中色散补偿光纤的研究

对五包层色散补偿光纤进行了研究,分析了各个参量对色散补偿光纤性能的影响,发现色散补偿光纤只有在一定范围的拉丝芯径内,以牺牲负色散数值为代价才能获得较大的负色散斜率。在1550nm处获得了不大于150ps/(nm·km)的负的总色散和负色散斜率的色散补偿光纤。采用在光纤拉丝时旋转预制棒的工艺减小了光纤的偏振模色散,并采用化学汽相沉积(MCVD)光纤生产工艺,研制出了性能较好的色散补偿光纤。     

圆形双芯微结构色散补偿光纤的色散特性分析

提出了一种圆形双芯微结构光纤,用频域有限差分法(FDFD),并对其色散特性进行了分析,并与前人提出的六边形双芯微结构色散补偿光纤进行了比较。结果表明:当圆形双芯微结构色散补偿光纤的高折射率区半径保持不变时,改变沿水平直径方向相邻空气洞中心点间的距离和空气洞的直径,能够控制有效模折射率的转折点,并在该处产生较大的负色散。由于圆形双芯微结构色散补偿光纤比六边形双芯微结构色散补偿光纤的有效模折射率对参数变化较为敏感,故前者更易于精确地控制转折点,达到色散补偿的目的。     

Anomalous dispersion in a solid, silica-based fiber

We demonstrate an all-solid (nonholey), silica-based fiber with anomalous dispersion at wavelengths where silica material dispersion is negative. This is achieved by exploiting the enhanced dispersion engineering capabilities of higher-order modes in a fiber, yielding + 60 ps/nm km dispersion at 1080 nm. By coupling to the desired higher-order mode with low-loss in-fiber gratings, we realize a 5 m long fiber module with a 300 fs/nm dispersion that yields a 1 dB bandwidth of 51 nm with an insertion loss of approximately 0.1 dB at the center wavelength of 1080 nm. We demonstrate its functionality as a critical enabler for an all-fiber, Yb-based, mode-locked femtosecond ring laser.     

宽带色散补偿光子晶体光纤的设计与优化

提出了一种新型的宽带色散补偿光子晶体光纤。通过增大光子晶体光纤(PCF)包层第一环空气孔半径r1,同时优化孔间距和包层其它环空气孔,在1550nm波长处获得了低至-1906.4ps/nm/km的负色散值。针对常规单模光纤的色散特性,设计出了宽带色散补偿光子晶体光纤,可补偿23倍长度的常规光纤,补偿的带宽达330nm,这在WDM系统中对多个信道同时进行色散补偿具有非常重要的意义。     

An efficient method for supercontinuum generation in dispersion-tailored Lead-silicate fiber taper

In this paper we theoretically study the broadband mid-IR supercontinuum generation (SCG) in a lead-silicate microstructured fiber (the glass for simulation is SF57). The total dispersion of the fiber can be tailored by changing the core diameter of the fiber so that dispersion profiles with two zero dispersion wavelengths (ZDWs) can be obtained. Numerical simulations of the SCG process in a 4 cm long SF57 fiber/fiber taper seeded by femto-second pulses at telecommunications wavelength of 1.55 µm are presented. The results show that a fiber taper features a continuous shift of the longer zero dispersion wavelength. This extends the generated continuum to a longer wavelength region compared to fibers with fixed ZDWs. The phase-matching condition (PMC) is continuously modified in the fiber taper and the bandwidth of the generated dispersive waves (DWs) is significantly broadened.     

高非线性光纤正常色散区产生超连续谱的数值研究

基于广义非线性薛定谔方程,通过数值计算对高非线性光纤正常色散区产生超连续谱进行了研究.结果表明,抽运脉冲的峰值功率、脉冲宽度以及脉冲初始啁啾对该光纤正常色散区超连续谱的形成有极其重要的影响;在高非线性光纤正常色散区产生超连续谱的过程中,三、四阶群速度色散甚至更高阶群速度色散对超连续谱的影响完全可以忽略,但与其他高非线性效应相比,自陡峭效应对超连续谱产生的影响更为明显.高功率超短光脉冲在高非线性光纤正常色散区,得到了没有泵浦成份残余、－20 dB谱宽达400 nm以上而频谱强度起伏小于10 dB的超宽而平坦超连续谱.     

零色散附近的交叉相位调制不稳定性分析

以三、四阶色散项的耦合非线性薛定谔方程为基础,考虑光纤损耗及高阶色散,研究了双光束在零色散附近的交叉相位调制不稳定性.理论上导出描述交叉相位调制不稳定性的色散方程,并进行数值模拟计算.结果表明：由于四阶色散的影响,在光纤的正常、反常色散区,交叉相位调制不稳定性均发生在两个频谱区.如光脉冲工作在最小群速度色散附近时,四阶色散对光纤的交叉相位调制不稳定性将起决定性作用,可使增益谱出现一个新的峰值.光纤损耗使增益的谱宽变窄.对给定的传输距离,随着光纤向零色散附近靠近,两个频谱区谱宽增加直到相互重叠.数值分析了两光波有差别时的交叉相位调制不稳定性.     

基于激光拍频实现啁啾光纤光栅色散的测量

以啁啾光纤光栅为例,研究了激光拍频的产生机制,并建立对啁啾光纤光栅色散的测量模型.详细阐述了系统结构和测量原理,并对测量结果和理论值进行了分析与比较,结果一致性较好.在频谱分析仪分辨率为2.5kHz的情况下,色散测量准确度可以达到0.1ps,啁啾光纤光栅色散的实际测量也证实了该系统的可行性,系统相对简单,测量准确度高,可为色散测量提供参考.     

Generation of the self-similar parabolic pulses by designing comb-like profiled dispersion fiber based on alternately arranged single-mode fibers and dispersion-shifted fibers

Based on the nonlinear Schrödinger equation and the linearly chirped parabolic pulse generation in the dispersion decreasing fiber with normal dispersion, a novel scheme for the generation of the self-similar parabolic pulse via a comb-like profiled dispersion fiber with normal group-velocity dispersion has been proposed and the corresponding model is established. We study, analytically and numerically, the evolution of the self-similar parabolic pulse in comb-like profiled dispersion fiber with dispersion profile close to that of the dispersion decreasing fiber, and the influence of different initial energies and pulse widths on the linearly chirped parabolic pulse formation in the comb-like profiled dispersion fiber. The results show that the evolution of the self-similar parabolic pulses can realized in the comb-like profiled dispersion fiber, the results of which are in good agreement with these of the dispersion decreasing fiber, and the best-matched scheme of designing and optimizing comb-like profiled dispersion fiber will help to obtain the ideal similaritons.     

一种40Gb/s单信道光纤通信系统中的动态色度色散补偿

提出了一种用于40 Gb/s单信道光纤通信系统中的动态色度色散(CD)补偿技术。采用2×2光开关,色散补偿光纤(DCF)等器件构成可调节色度色散补偿器;提取中心频率为12GHz的窄带电功率信号作为反馈信号控制可调节色度色散补偿器,提取的窄带电功率值随系统中的累积色度色散值的增大而减小。实验证明,整个补偿系统的最长响应时间为0.7 s;补偿范围和补偿精度分别为81.55 ps/nm和5.28 ps/nm,通过增加光开关的数量和缩短每段色散补偿光纤的长度可以进一步提高补偿范围和精度。通过对比补偿前后系统的眼图可以看出:该系统能有效地补偿40 Gb/s光纤通信系统中动态变化的色度色散。     

色散补偿和色散位移光纤实现光脉冲压缩

根据超短光脉冲在光纤中传输的非线性薛定谔方程，模拟了不同色散参量情况下色散补偿和色散位移光纤对增益开关半导体激光器产生的光脉冲的压缩，给出了光脉冲在经过色散补偿光纤前后的啁啾曲线。结果表明，使用色散参量D分别为-150，-180和-20ps/(nm·km)的色散补偿光纤可以实现其他脉冲压缩方法的压缩效果，最大压缩因子达到6.09，但色散参量越大，所需光纤长度就越短。此外，脉冲经过色散补偿光纤后线性啁啾几乎为零。还利用色散位移光纤对脉冲进行孤子压缩，脉冲宽度由最初的45ps减小到1.23ps。指出采用这2种光纤相结合的方法可以对光脉冲实现高效压缩。     

Analyses of constraints on high speed optical code division multiplexing access (OCDMA) link parameters due to fiber optic chromatic dispersion

In direct sequence-optical code division multiplexing access (DS-OCDMA) system networks, data rate and data spreading technique involved in such systems require a high chip rate. Transmission link in these systems is significantly affected by the fiber chromatic dispersion. In this study, we have developed and employed a simple model to estimate the G652 fiber dispersion effects. OCDMA technique has been employed to investigate fiber chromatic dispersion effects on multiple access interference (MAI). We have found that, at a short optical fiber length, the optical fiber dispersion has a significant impact on the high data rate transmission systems (higher than 750 Mbit/s). The performance and optimization of optical orthogonal code (OOC) in the OCDMA system is reported. We have demonstrated that, for a high data rate, even if dispersion compensated devices are not deployed, the BER can be significantly improved when the OOC desired length is selected. We have shown that when compensation dispersion devices are not deployed in the system, there is a trade off between the limited dispersion effects and the MAI.     

Design of zero dispersive double clad fiber for high efficiency operation of two color light

A double clad solid silica fiber is newly designed for applications which need the high efficiency operation of two colors of light. Ultrashort pulses with a central wavelength of 800?nm are delivered by the core of the double clad fiber which can realize the transmission of the optical pulses with a net chromatic dispersion of zero. This is achieved by integrating the double clad fiber with a pair of long period gratings, which allows optical pulses to propagate in a higher order mode (LP₀₂) in the middle of the fiber as well as in a fundamental mode (LP₀₁) at the beginning and end of the fiber. The index profile of the double clad fiber is engineered so that the higher order mode has high anomalous dispersion that can be used to compensate for normal dispersion of the fundamental mode. By controlling the lengths of the fiber where pulses are in a fundamental and in a higher order modes, the fiber with total zero dispersion can be realized. The double clad fiber can collect 100?% of visible light within the numerical aperture of 0.21 with a loss of the optical pulses less than 1?%. The design of this fiber is essential for applications including fiber-optic nonlinear imaging for compactness, robustness, and low optical power loss in dispersion compensation.     

菱形纤芯光子晶体光纤色散与双折射特性分析

针对光子晶体光纤多零色散点、高双折射的应用要求, 设计了一种新型结构的光子晶体光纤, 其纤芯由位于菱形四个角上的圆形空气孔组成. 通过有限元数值分析方法对该种结构光子晶体光纤的色散特性和双折射特性进行数值仿真, 得到色散与波长、色散与纤芯圆孔尺寸、双折射与波长、双折射与纤芯圆孔尺寸的关系. 研究结果表明:在满足光纤传输功率要求的条件下, 光纤的双折射在d₁<0.8 μupm 时的性能较好. 同时, 该种结构的光子晶体光纤在芯区直径满足d₁=0.4 μupm或 d₁=0.6 μupm时会出现两个零色散点, 这对进一步研制具有多零色散点的光子晶体光纤具有重要的意义.     

双折射色散阶跃光纤中拉曼效应和参量放大增益谱

在拉曼效应和参量放大共同作用下,当激光脉冲在双折射光纤中传输时,根据所遵循的耦合模方程,通过引入平行拉曼增益的洛伦兹模型,导出了当输入泵浦波偏振方向同双折射轴成45°角时,在双折射色散阶跃光纤中拉曼效应和参量放大共同作用所导致的增益,讨论并分析了在不同色散区增益谱随相关参量的变化。结果表明:由于拉曼效应、参量放大、双折射和色散的相互作用,导致增益谱的斯托克斯波与反斯托克斯波彼此不对称;在反常色散区,产生的增益以反斯托克斯波为主,在正常色散区则以斯托克斯波为主;当表征距离的级数m发生变化时,增益谱也随之发生变化,可以利用色散阶跃光纤在适当的级数m位置提取T频率脉冲。