V2O5/TiO2-ZrO2催化剂上甲醇选择氧化制甲缩醛

采用共沉淀法制备TiO2-ZrO2复合氧化物载体、等体积浸渍法制备V2O5/TiO2-ZrO2催化剂,对催化剂在温和条件下甲醇选择氧化生成甲缩醛(DMM)反应进行研究.结果表明,与单一氧化物载体TiO2或ZrO2负载的钒基催化剂相比,V2O5/TiO2-ZrO2对甲醇选择氧化具有较好的催化性能.XRD、NH3-TPD和...     

不同孔道结构的氧化硅负载钒氧化物催化丙烷氧化脱氢

采用固定床微型反应装置,结合催化剂的原位电子自旋共振光谱、程序升温表面反应和紫外漫反射光谱等技术,研究了丙烷氧化脱氢的介孔氧化硅负载钒氧化物催化剂的性能和表面氧物种的状态及其反应性.结果表明,催化剂载体孔结构是影响钒氧物种分散状态乃至催化性能的一个重要因素.SBA-15负载钒氧化物催化剂因具有较大的比表面积和较大的孔径,不仅具有较高的丙烷氧化脱氢催化活性,而且具有较高的丙烯选择性.复合型钒氧化物催化剂表面与V离子相连的晶格氧物种是丙烷氧化脱氢牛成内烯的主要活性物种,载体表面高度分散的钒氧物种具有较高的丙烷氧化脱氢催化活性.负载型钒氧化物催化剂晶格氧物种是丙烷氧化脱氢转化为丙稀的主要活性物种,CO_2分子可以再生钒氧化物催化剂的晶格氧物种,同时它对丙烯的深度氧化作用较弱,因此在负载型钒氧化物催化剂上CO_2氧化丙烷可高选择性地生成丙烯.     

CO2消除镓氢物种提升Ga2O3/SiO2丙烷脱氢反应性能

丙烯是一种基础石油化工原料,在全球石油化工生产中占有重要地位.以丙烯为原料可生产许多石油化学品,如丙烯腈、环氧丙烷和聚丙烯等.经济快速发展带动了丙烯下游衍生物产业的发展,进而增加了对丙烯的需求量,因此尽管近年来丙烯产能逐年上升,丙烯产量与需求量之间仍存在较大缺口.传统的丙烯生产路径主要是石脑油蒸汽裂解和重质油催化裂化.然而,随着石油资源的短缺和页岩气的发展,丙烷脱氢作为一种直接生产丙烯的技术,成为丙烯生产领域的研究热点.近年来,镓基催化剂由于其较少的积碳和较高的催化活性受到了越来越多的关注.镓基催化剂在丙烷脱氢反应中的活性位点也得到了更多研究.在镓基催化剂中,镓氧化物具有丙烷脱氢活性,而丙烷脱氢反应过程中产生的镓氢(Gaδ+-Hx)物种不稳定,且会造成丙烯选择性降低,导致丙烯产率降低.因此,反应过程中原位消除镓氢物种对于提高丙烷脱氢反应性能具有非常重要的意义.本文将CO2作为温和氧化剂引入Ga2O3/SiO2催化的丙烷脱氢反应中,促进不利的中间产物Gaδ+-Hx的转化,再生丙烷脱氢的活性位点Ga3+-O,从而提高催化性能.原位红外光谱实验结果表明,CO2可有效消除Gaδ+-Hx.在不同反应温度下,引入CO2可显著提高Ga2O3/SiO2催化丙烷脱氢的转化率,特别是选择性.反应4.5 h时,3Ga2O3/SiO2催化丙烷脱氢的选择性从93％降低到89％;引入CO2后,丙烯选择性可提高到并维持在93％.Ga2O3负载量由3 wt％提高到10 wt％时,引入CO2仍可促进反应性能.当CO2:C3H8由0.5增加到3时,引入CO2带来的反应性能提升基本相同.同时,引入CO2大大减少反应过程中产生的积碳.本文对镓基催化剂丙烷脱氢活性中心的认识和提高丙烷脱氢反应性能提供了新方向.     

CO2氧化丙烷脱氢制丙烯V-Cr/SBA-15催化剂的研究

以介孔分子筛SBA-15为载体，V和Cr为活性组分，采用浸渍法制备了不同V和Cr质量分数的V-Cr/SBA-15催化剂，研究了其对二氧化碳氧化丙烷制丙烯反应的催化性能，采用XRD、BET、TPR等分析测试技术对催化剂的结构进行了表征。结果表明，催化剂中V组分的质量分数较大时以V2O5物相存在，Cr组分以Cr2O3物相存在，它们对SBA-15分子筛的介孔特征影响不大；V、Cr单组分和双组分催化剂都具有较好的CO2氧化丙烷脱氢制丙烯的催化性能，V和Cr质量分数相同的双组分催化剂比单组分催化剂具有更高的催化活性；在V-Cr/SBA-15催化剂中，V和Cr之间存在一定的相互作用，进而改变了催化剂的氧化还原性能，提高了催化剂的催化性能。     

丙烷选择氧化用VPO／SiO2催化剂的研究

 摘要：对比研究了VPO和VPO／SiO2催化剂的结构、表面元素氧化态、还\r\n原性及其对丙烷选择氧化反应的催化性能．与VPO催化剂相比，VPO／S\r\niO2催化剂具有较大的比表面积；VPO主要以（VO）2P2O7的形式高度分散于SiO2表面；VPO／SiO2催化剂的还原温度较低；VPO／SiO2催化剂与丙烷的相互作用较强；在反应条件下，VPO／SiO2催化剂的活性较高，但产物丙烯的选择性较低，并有丙烯醛等C3含氧化合物生成．这可能是由于VPO／SiO2催化剂表面的V与Si发生了相互作用之故．随着VPO担载量的增加，VPO／SiO2催化剂的比表面积减小；催化剂的还原温度略有升高，可还原的晶格氧量增加；催化剂表面与丙烷的相互作用增强；丙烷转化率升高而丙烯选择性降低，丙烯醛选择性在5％VPO／SiO2催化剂上最高．这可能是由于随着VPO担载量的增加，催化剂表面晶格氧的密度增大所致．     

丙烯在Au/TiO2催化剂上的化学吸附与临氢环氧化反应

环氧丙烷;丙烯环氧化;丙烯在Au/TiO2催化剂上的化学吸附与临氢环氧化反应     

Te掺杂对MoPO/SiO2催化剂上丙烷选择氧化制丙烯醛反应的影响

 考察了Te的添加及Te含量对MoPO/SiO2催化剂催化丙烷选择氧化制丙烯醛反应性能的影响. MoPO/SiO2催化剂对丙烷选择氧化制丙烯醛反应的中间产物丙烯选择性较高,而Te的添加促进了丙烯向丙烯醛的转化. N2吸附、XRD、Raman、XPS、H2-TPR、丙烷脉冲、NH3-TPD和Py-IR等实验结果表明,催化剂添加Te后虽然比表面积有所下降,但单位比表面积上的酸量增加,催化剂低温可还原性得到改善,从而有利于丙烷的转化. Te可能有利于丙烯α-H的脱除和/或烯丙基的插氧反应.     

氧化铈的结构对其热稳定性及催化丙烷氧化脱氢反应性能的影响

采用湿化学法制备了低维氧化铈的纳米棒和纳米颗粒,通过原位X射线粉末衍射、透射电镜和N2物理吸附等技术研究了氧化铈纳米结构对其热稳定性的影响.结果表明,氧化铈纳米棒的稳定性更高.采用浸渍法制备了氧化铈负载的氧化钒催化剂,并用于丙烷氧化脱氢反应中,发现以氧化铈纳米棒为载体的催化剂表现出更高的丙烯选择性,这可能是由于棒状结构的开放性有利于产物丙烯的直接扩散.     

TiO2–ZrO2的表征及其异丙醇催化转化性能

用共沉淀法制备了TiO2-ZrO2复合氧化物. 采用N2吸附、XRD、TEM、NH3和CO2吸附量热、NH3吸附红外对TiO2-ZrO2体系的结构及酸碱性等进行了表征. 结果表明: 与单纯的氧化物相比, 形成的复合氧化物为无定形物相, 有介孔结构, 表面积明显提高, 可达218 m2·g-1; 初始吸附热差别不大, 但具有更多的表面B酸位; 随着TiO2掺入量的增大, 复合氧化物表面碱位减少. 异丙醇催化转化, 在无氧条件下, ZrO2、TiO2和TiO2-ZrO2复合氧化物上丙烯的选择性大于90%, 说明这些氧化物具有强的表面酸性; 在有氧条件下, ZrO2和TiO2丙酮的选择性达到70%～85%, 主要体现为氧化还原性; 而在复合氧化物上丙烯选择性增大到70％左右, 丙酮的选择性下降为30%左右, 表明生成的复合氧化物表面上的氧化还原性削弱, 酸性增强.     

B修饰的ZrO2及其制备p H值对PtSn/B-ZrO2丙烷脱氢反应性能的影响（英文）

丙烯作为一种重要的石油化工基础原料,传统上是从石脑油蒸汽裂解或催化裂化过程中作为副产物生产的.随着原油的枯竭和页岩气开发技术的成熟,通过乙烷蒸汽裂解制备乙烯更具吸引力并已得到广泛的工业应用,但该路线乙烯选择性高,而副产物丙烯数量有限.为满足不断增加的丙烯需求量,利用油田气和页岩气中低附加值的丙烷为原料,将其直接脱氢制丙烯(PDH)具有重要的现实意义.目前已开发成功的PDH技术采用的催化剂主要为负载PtSn型催化剂和Cr基催化剂.其中,Pt基催化剂较Cr基催化剂更加环境友好,因此得到了更广泛的应用.由于Pt元素的昂贵和稀有,制备低Pt含量和良好性能的催化剂极具吸引力.UOP Oleflex工艺开发的最新一代催化剂DEH-16仅含有0.3 wt%Pt,相对于前一代催化剂Pt含量降低30%.然而,许多文献报道,随着Pt含量的降低,催化剂的稳定性很容易恶化,降低Pt含量并保持催化剂性能仍具有一定的挑战.研究表明,含有更多Lewis酸性位点和更少Bronsted酸位点的催化剂显示出较好的丙烷脱氢活性和丙烯选择性.此外,源自缺陷位或配位不饱和位的Lewis酸性位也可为负载的金属颗粒提供锚定位点.BASF对ZrO2作为载体的丙烷脱氢催化剂进行了广泛研究,但其催化剂尚未完全商业化.有文献报道,ZrO2负载的PtSn催化剂在脱氢反应中的稳定性较差.将元素硼(B)加入到ZrO2中可以极大地抑制Bronsted酸性而提高Lewis酸量和酸强度,因此我们推测含有适量配位不饱和Zr位点的ZrO2作为PtSn丙烷脱氢催化剂载体可能具有优异的性能.载体的合成pH值对催化剂PDH性能也会有影响.然而,目前还没有硼改性的ZrO2(B-ZrO2)合成pH值对PDH催化性能影响的研究.本文研究了B-ZrO2的合成pH值(9,10和11)对PtSn/B-ZrO2在丙烷脱氢反应中催化性能的影响.Py-IR结果表明各pH值下合成的B-ZrO2均只有Lewis酸,NH3-TPD结果则表明B-ZrO2的Lewis酸量和强度随合成pH值的增加而增加.XPS结果显示,载体对Pt和Sn电子性质的影响不容忽视.由于OSC与CO氧化活性之间没有线性关系,因此Pt和Sn之间的相互作用程度在CO氧化反应中可能起主要作用,并有如下递增趋势:PtSn/B-ZrO2-9相似文献   

Sc2MgGa2 and Y2MgGa2

Scandium magnesium gallide, Sc₂MgGa₂, and yttrium magnesium gallide, Y₂MgGa₂, were synthesized from the corresponding elements by heating under an argon atmosphere in an induction furnace. These intermetallic compounds crystallize in the tetragonal Mo₂FeB₂‐type structure. All three crystallographically unique atoms occupy special positions and the site symmetries of (Sc/Y, Ga) and Mg are m2m and 4/m, respectively. The coordinations around Sc/Y, Mg and Ga are pentagonal (Sc/Y), tetragonal (Mg) and triangular (Ga) prisms, with four (Mg) or three (Ga) additional capping atoms leading to the coordination numbers [10], [8+4] and [6+3], respectively. The crystal structure of Sc₂MgGa₂ was determined from single‐crystal diffraction intensities and the isostructural Y₂MgGa₂ was identified from powder diffraction data.     

Zur Kenntnis der Dialkalimetalldichalkogenide β-Na2S2, K2S2, α-Rb2S2, β-Rb2S2, K2Se2, Rb2Se2, α-K2Te2, β-K2Te2 und Rb2Te2

On Dialkali Metal Dichalcogenides β-Na₂S₂, K₂S₂, α-Rb₂S₂, β-Rb₂S₂, K₂Se₂, Rb₂Se₂, α-K₂Te₂, β-K₂Te₂ and Rb₂Te₂ The first presentation of pure samples of α- and β-Rb₂S₂, α- and β-K₂Te₂, and Rb₂Te₂ is described. Using single crystals of K₂S₂ and K₂Se₂, received by ammonothermal synthesis, the structure of the Na₂O₂ type and by using single crystals of β-Na₂S₂ and β-K₂Te₂ the Li₂O₂ type structure will be refined. By combined investigations with temperature-dependent Guinier-, neutron diffraction-, thermal analysis, and Raman-spectroscopy the nature of the monotropic phase transition from the Na₂O₂ type to the Li₂O₂ type will be explained by means of the examples α-/β-Na₂S₂ and α-/β-K₂Te₂. A further case of dimorphic condition as well as the monotropic phase transition of α- and β-Rb₂S₂ is presented. The existing areas of the structure fields of the dialkali metal dichalcogenides are limited by the model of the polar covalence.     

Crystal Structures of [Bu2Sn(O2PPh2)2], [Ph2Sn(O2PPh2)2], and [PhClSn(O2PPh2)OMe]2. Raman Spectra of [Ph2Sn(O2PPh2)2] and [PhClSn(O2PPh2)OMe]2

[(n‐Bu)₂Sn(O₂PPh₂)₂] ( 1 ), and [Ph₂Sn(O₂PPh₂)₂] ( 2 ) have been synthesized by the reactions of R₂SnCl₂ (R=n‐Bu, Ph) with HO₂PPh₂ in Methanol. From the reaction of Ph₂SnCl₂ with diphenylphosphinic acid a third product [PhClSn(O₂PPh₂)OMe]₂ ( 3 ) could be isolated. X‐ray diffraction studies show 1 to crystallize in the monoclinic space group P2₁/c with a = 1303.7(1) pm, b = 2286.9(2) pm, c = 1063.1(1) pm, β = 94.383(6)°, and Z = 4. 2 crystallizes triclinic in the space group , the cell parameters being a = 1293.2(2) pm, b = 1478.5(4) pm, c = 1507.2(3) pm, α = 98.86(3)°, β = 109.63(2)°, γ = 114.88(2)°, and Z = 2. Both compounds form arrays of eight‐membered rings (SnOPO)₂ linked at the tin atoms to form chains of infinite length. The dimer 3 consists of a like ring, in which the tin atoms are bridged by methoxo groups. It crystallizes triclinic in space group with a = 946.4(1) pm, b = 963.7(1) pm, c = 1174.2(1) pm, α = 82.495(6)°, β = 66.451(6)°, γ = 74.922(6)°, and Z = 1 for the dimer. The Raman spectra of 2 and 3 are given and discussed.     

The alkali hypophosphites KH2PO2, RbH2PO2 and CsH2PO2

The structures of the hypophosphites KH₂PO₂ (potassium hypophosphite), RbH₂PO₂ (rubidium hypophosphite) and CsH₂PO₂ (caesium hypophosphite) have been determined by single‐crystal X‐ray diffraction. The structures consist of layers of alkali cations and hypophosphite anions, with the latter bridging four cations within the same layer. The Rb and Cs hypophosphites are isomorphous.     

Electrochemical study of (NEt4)2Cl2FeS2MoS2 and (NEt4)2Cl2FeS2MoS2FeCl2

Summary The ability of [MoS₄]^2–, anions to be used as ligands for transition metal ions has been widely demonstrated, especially with Fe²⁺. The present study has been restricted to linear complexes such as (NEt₄)₂ [Cl₂FeS₂MoS₂] and (NEt₄)₂[Cl₂FeS₂MoS₂FeCl₂]. Their electrochemical properties are described: upon electrochemical reduction, these compounds yield MoS₂, as a black precipitate, and an iron complex in solution, assumed to be [SFeCl₂]^2–. The electrochemical reduction goes through two electron transfers, coupled with the breakdown of the molecular skeleton: a DISPl and an ECE mechanism. Depending on the solvent, the following equilibrium may be observed: [Cl₄Fe₂MoS₄]^2–[Cl₂FeMoS₄]^2–+FeCl₂. The equilibrium constant, K_D, was evaluated by differential pulse polarography. K_D is tightly related to the donor number of the solvent.     

Syntheses,Spectroscopic Studies,and Crystal Structures of Me2Sn(O2PPh2)2, Ph2Pb(O2PMe2)2, and Ph2Pb(O2PPh2)2

Me₂Sn(O₂PPh₂)₂ ( 1 ), Ph₂Pb(O₂PMe₂)₂ ( 2 ), and Ph₂Pb(O₂PPh₂)₂ ( 3 ) have been synthesized by the reactions of Me₂SnCl₂ or Ph₃PbCl with the corresponding diorganophosphinic acid in methanol. X‐ray diffraction studies show that the diorganophosphinate groups behave as double bridges between the metal atoms leading to polymeric ring‐chain structures with M₂O₄P₂ (M = Pb, Sn) eight‐membered rings. The organic groups bonded to the metal atoms are in trans‐position in the resulting octahedral arrangement around the metal atoms. The IR and the mass spectra were reported and discussed.     

Thermal decomposition of Me3SnO2PCl2, Me2Sn(O2PCl2)2 and Ph3SnO2PCl2

TG and DTA studies on Me₃SnO₂PCl₂, Me₂Sn(O₂PCl₂)₂ and Ph₃SnO₂PCl₂ were carried out under dynamic argon atmosphere. The results show that the decomposition proceeds in different stages leading to the formation of Sn₃(PO₄)₂ as a stable product. This compound was characterized by IR spectroscopy. Decomposition schemes involving reductive elimination reactions were proposed.