Neutron activation analysis of rhenium in rocks and sediments by extraction chromatography on a pyridine-Kel-F column

A simple method for the determination of rhenium in rocks and sediments has been established. After a neutron-irradiated sample was decomposed by NaOH−Na₂O₂ fusion, the alkaline solution was fed onto a column of the mixed solvent pyridine-benzene (7:3 v/v) supported on Kel-F powder. By passage through the column of 4, 5N NaOH solution which had been equilibrated with the solvent mixture, perrhenate ion remained on the column but other nuclides were eluted. Subsequently, the perrhenate ion on the column could be eluted with a small amount of distilled water, and precipitated as tetraphenylarsonium perrhenate for counting the γ-activity of¹⁸⁶Re. By the present method 0.1 ng of rhenium could be determined with a recovery of 90–95% and an error of ±10%. A part of this work was performed at the Research Reactor Institute, Kyoto University.     

Determination of naturally occurring uranium concentrations in seawater,sediment, and marine organisms in Japanese estuarine areas

For safety assessments of geological repositories of nuclear waste, understanding of uranium (U) fate in estuarine areas is important because U chemical behavior in the areas is expected to be complex. Environmental transfer parameters such as sediment–water distribution coefficients (K _d) and concentration ratios (CRs) for marine organisms are useful in mathematical models for the assessment. However, due to its low concentration in estuarine water, K _d and CF data for U are scarce. Thus we studied a rapid method for separation and concentration of U from estuarine water samples using NOBIAS-CHELATE PA1 resin columns followed by inductively coupled plasma mass spectrometry (ICP-MS) for U measurement. Chemical recovery was about 100% at pH of 5.7 ± 0.1 from the water samples and alkali and alkaline earth metals were removed. The method was used to measure U concentrations in estuarine water samples collected at eight Japanese estuarine areas; they ranged from 0.1 to 3.8 μg L⁻¹. We also measured U concentrations in sediment and marine organism samples by ICP-MS after acid digestion. Using these values, we observed K _d (range: 39–284 L kg⁻¹) and CRs (0.86–52 L kg⁻¹ for macroalgae, 0.087–15 L kg⁻¹ for crustaceans, and 0.52–93 L kg⁻¹ for molluscs).     

Separation and determination of selenium in water samples by the combination of APDC coprecipitation: X-ray fluorescence spectrometry

A sensitive and non chromatographic analytical procedure for the separation of inorganic selenium species in natural water has been performed. A combination of APDC coprecipitation and determination by an absolute thin layer Energy dispersive X-ray fluorescence spectrometry method was used. The influence of various analytical parameters such as element concentration, oxidation states and pH on the recoveries of Se (IV) was examined. The presence of organic matter and bicarbonate anions, typical components in Cuban groundwater samples, was also tested. Negligible matrix effects were observed. At pH 4 a 100% recovery was found for Se (IV). The coprecipitation recovery of the oxidized selenium species (Se (VI)) was null for the selected concentration range (5–100 μg L⁻¹). When the Se (VI) was reduced by heating the solution with 4 mol L⁻¹ HCl, quantitative recovery was also obtained. The determination of total selenium was conducted by the application of the oxidation–reduction process and the analytical procedure for Se (IV). Se (VI) content was calculated as the difference between total selenium and Se (IV). The detection limit was 0.13 μg L⁻¹. The relative standard deviation was lower than 3.5% for 5 μg L⁻¹ of Se (IV). The trueness of the method was verified by using standardized hydride generation-atomic absorption spectrometry technique. The results obtained using the EDXRF technique were in good agreement with the ones determined by HG-AAS. The proposed method was applied to the determination of Se (IV) in surface water and groundwater samples.     

Organosilica composite for preconcentration of phenolic compounds from aqueous solutions

A new adsorbent is proposed for the solid-phase extraction of phenol and 1-naphthol from polluted water. The adsorbent (TX-SiO₂) is an organosilica composite made from a bifunctional immobilized layer comprising a major fraction (91%) of hydrophilic diol groups and minor fraction (9%) of the amphiphilic long-chain nonionic surfactant Triton X-100 (polyoxyethylated isooctylphenol) (TX). Under static conditions phenol was quantitatively extracted onto TX-SiO₂ in the form of a 4-nitrophenylazophenolate ion associate with cetyltrimethylammonium bromide. The capacity of TX-SiO₂ for phenol is 2.4 mg g⁻¹ with distribution coefficients up to 3.4 × 10⁴ mL g⁻¹; corresponding data for 1-naphthol are 1.5 mg g⁻¹ and 3 × 10³ mL g⁻¹. The distribution coefficient does not change significantly for solution volumes of 0.025–0.5 L and adsorbent mass less than 0.03 g; 1–90 μg analyte can be easily eluted by 1–3 mL acetonitrile with an overall recovery of 98.2% and 78.3% for phenol and 1-naphthol, respectively. Linear correlation between acetonitrile solution absorbance (A ₅₄₀) and phenol concentration (C) in water was found according to the equation A ₅₄₀ = (6 ± 1) × 10⁻² + (0.9 ± 0.1)C (μmol L⁻¹) with a detection range from 1 × 10⁻⁸ mol L⁻¹ (0.9 μL g⁻¹) to 2 × 10⁻⁷ mol L⁻¹ (19 μL g⁻¹), a limit of quantification of 1 μL g⁻¹ (preconcentration factor 125), correlation coefficient of 0.936, and relative standard deviation of 2.5%. A solid-phase colorimetric method was developed for quantitative determination of 1-naphthol on adsorbent phase using scanner technology and RGB numerical analysis. The detection limit of 1-naphthol with this method is 6 μL g⁻¹ while the quantification limit is 20 μL g⁻¹. A test system was developed for naked eye monitoring of 1-naphthol impurities in water. The proposed test kit allows one to observe changes in the adsorbent color when 1-naphthol concentration in water is 0.08–3.2 mL g⁻¹.     

Analysis of spectinomycin in fermentation broth by reversed-phase chromatography

A pre-column derivatized high-performance liquid chromatographic (HPLC) method with ultraviolet-visible detection was developed to measure the concentrations of spectinomycin in fermentation broth. Derivatization reagents, 2,4-dinitrophenylhydrazine in acetonitrile (5 mg mL⁻¹) and trifluoroacetic acid in acetonitrile (0.8 mol L⁻¹), were added to an aliquot of the fermentation broth, and the mixture was incubated for 60 min at 70°C. The resulting derivative was separated from other compounds by isocratic elution in a reversed-phase column Zorbax SB-C18 (250 mm × 4.6 mm, 5 μm). Mobile phase consisted of acetonitrile, tetrahydrofuran, and water (φ _r = 40: 35: 25) and the flow rate was 1.0 mL min⁻¹. The detection wavelength was 415 nm. The standard curve for spectinomycin sulfate was linear with correlation coefficients of 0.9997 in the range of 25 μg mL⁻¹ to 600 μg mL⁻¹. The relative standard deviation values ranged from 0.43 % to 2.18 % depending on the concentration of samples. The average recovery was 101.5 %. The limit of detection was 50 ng mL⁻¹.     

Determination of mono and disaccharide content of enteral formulations by gas chromatography

Summary A quantitative GC method has been developed which allows determination of mono and disaccharides in enteral formulations. The method is based on the isolation of the mono and disaccharide fraction on a charcoal-celite column and conversion to trimethylsilylated oximes (TMS-oximes). The repeatability of the complete method and recovery were acceptable. In the five commercial samples assayed, maltose was the main sugar (5.24–8.85 gL⁻¹) followed by glucose (1.06–2.41 gL⁻¹) and lactose (0–1.17 gL⁻¹) Low levels of fructose (0–0.18 gL⁻¹) and sucrose (0–0.07 gL⁻¹) were observed and galactose was detected in two of the samples. The presence of maltulose is reported in enteral formulations for the first time. Maltulose formed from maltose during processing, was present in variable amounts (0.12–1.07 gL⁻¹) and could be a useful indicator for enteral formulation classification.     

Polar herbicides,pharmaceutical products,perfluorooctanesulfonate (PFOS), perfluorooctanoate (PFOA), and nonylphenol and its carboxylates and ethoxylates in surface and tap waters around Lake Maggiore in Northern Italy

A survey of contamination of surface and drinking waters around Lake Maggiore in Northern Italy with polar anthropogenic environmental pollutants has been conducted. The target analytes were polar herbicides, pharmaceuticals (including antibiotics), steroid estrogens, perfluorooctanesulfonate (PFOS), perfluoroalkyl carboxylates (including perfluorooctanoate PFOA), nonylphenol and its carboxylates and ethoxylates (NPEO surfactants), and triclosan, a bactericide used in personal-care products. Analysis of water samples was performed by solid-phase extraction (SPE) then liquid chromatography–triple-quadrupole (tandem) mass spectrometry (LC–MS–MS). By extraction of 1-L water samples and concentration of the extract to 100 μL, method detection limits (MDLs) as low as 0.05–0.1 ng L⁻¹ were achieved for most compounds. Lake-water samples from seven different locations in the Southern part of Lake Maggiore and eleven samples from different tributary rivers and creeks were investigated. Rain water was also analyzed to investigate atmospheric input of the contaminants. Compounds regularly detected at very low concentrations in the lake water included: caffeine (max. concentration 124 ng L⁻¹), the herbicides terbutylazine (7 ng L⁻¹), atrazine (5 ng L⁻¹), simazine (16 ng L⁻¹), diuron (11 ng L⁻¹), and atrazine-desethyl (11 ng L⁻¹), the pharmaceuticals carbamazepine (9 ng L⁻¹), sulfamethoxazole (10 ng L⁻¹), gemfibrozil (1.7 ng L⁻¹), and benzafibrate (1.2 ng L⁻¹), the surfactant metabolite nonylphenol (15 ng L⁻¹), its carboxylates (NPE₁C 120 ng L⁻¹, NPE₂C 7 ng L⁻¹, NPE₃C 15 ng L⁻¹) and ethoxylates (NPE _n Os, n = 3-17; 300 ng L⁻¹), perfluorinated surfactants (PFOS 9 ng L⁻¹, PFOA 3 ng L⁻¹), and estrone (0.4 ng L⁻¹). Levels of these compounds in drinking water produced from Lake Maggiore were almost identical with those found in the lake itself, revealing the poor performance of sand filtration and chlorination applied by the local waterworks.     

A novel rhenium-aqua structure: the synthesis and structural characterization of (PPh4)4[ReN(H2O)(CN)3-μ-CN-ReN(CN)4]?·?5H2O

A novel cyano bridged rhenium nitrido complex, [ReN(H₂O)(CN)₄-μ-CN-ReN(CN)₄]⁴⁻ (I) was isolated during a kinetic study of the reaction of ReN(H₂O)(CN)₄]²⁻ with pyridine-2,3-dicarboxylic acid. Yellow crystals of (I), suitable for X-ray structure determination were isolated and the structural data showed an unsymmetrical binuclear rhenium complex with a cyano ligand acting as a bridge between two metal atoms, Re(1) and Re(2). The nitrogen of the bridged cyano ligand coordinates trans to the nitrido ligand of Re(1). The rhenium-nitrido bond distances are 1.657(4) and 1.656(5) ? for Re(1)–N(9) and Re(2)–N(10) respectively. Re(1) and Re(2) are displaced from the planes formed by the four carbon atoms of the cyano ligands towards the nitrido ligands by 0.348(2) and 0.3403(2) ?, respectively.     

Voltammetric determination of 2,4-dinitrophenol and 2,5-dinitrophenol using a poly-aspartic acid modified electrode1

In pH 5.0, 0.1 mol l⁻¹ NaAc-HAc buffer solution, 2,4-dinitrophenol and 2,5-dinitrophenol exhibited sensitive and distinguishable voltammetric responses at the glassy carbon electrode modified with poly-aspartic acid. By measuring the reduction peak currents of nitro groups in different positions, dinitrophenol isomers have been determined simultaneously and quantitatively. The linear calibration ranges were 1.1 × 10⁻⁶–6.0 × 10⁻⁴ mol l⁻¹ for 2,4-dinitrophenol and 7.0 × 10⁻⁷–6.0 × 10⁻⁴ mol l⁻¹ for 2,5-dinitrophenol, with detection limits of 2.7 × 10⁻⁷ and 1.1 × 10⁻⁷ mol l-1 respectively. This method has been applied to the detection of dinitrophenols in simulation water sample, and the recovery was from 96.7 to 102.5%.     

Determination of trace Cd and Pb in natural waters by direct single drop microextraction combined with electrothermal atomic absorption spectrometry

A new method of direct single-drop microextraction combined with electrothermal atomic absorption spectrometry (ETAAS) is presented for the determination of trace Cd and Pb with dithizone (H₂DZ) as chelating reagent. Factors influencing the microextraction efficiency and determination, such as pH, microdrop volume, stirring rate, extraction time were evaluated. Under the optimized experimental conditions, the detection limits of the method are 2 and 90 pg mL⁻¹ for Cd and Pb, and the relative standards deviations for 0.5 ng mL⁻¹ Cd and 10 ng mL⁻¹ Pb are 11 and 12.8%. After 10 min of extraction, the enrichment factors for Cd and Pb are 118 and 90, respectively. The results for the determination of Cd and Pb in tap water, spring water, river water, pond water, lake water and spiked water samples demonstrate the accuracy, recovery and applicability of the method. An environmental water certified reference material (GSBZ 50009-88) was analyzed, and the determined values are in a good agreement with the certified values. Correspondence: Bin Hu, Department of Chemistry, Wuhan University, Wuhan 430072, P.R. China     

A sensitive and simple flotation-spectrophotometric method for the determination of microgram amounts of silver using Schiff base 2-[(2-mercaptophenyliminio)methyl]phenol

A simple and sensitive spectrophotometric procedure for the determination of microgram amounts of silver has been developed. The method is based on the flotation of the complex of Schiff base, 2-[(2-mercaptophenylimino)methyl]phenol (MPMP), and silver at the aqueous solution-chloroform interface. The complex was then separated and dissolved in 5 mL of methanol, and its absorbance was measured at 330 nm. The quantitative flotation of the complex was possible from 5–140 mL of the aqueous phase in the pH range of 1–5. For a 100-mL aliquot of the water sample, the Beer’s law was obeyed over the range from 1 × 10⁻⁷ to 5 × 10⁻⁶ M of silver. The Sandell’s sensitivity was 6.9 × 10⁻⁹ mol cm⁻² for a 0.001 absorbance unit. The method is simple, rapid, free from the interference of many cations and anions, and has a wide linear range. The procedure was successfully applied to the determination of trace amounts of silver in tap water, well water, waste water in the mining industries, and a lead-concentrate reference material. The accuracy was assessed using either a recovery experiment and independent analysis with standard additions, or the analysis of certified reference materials. The text was submitted by the authors in English.     

Isocratic Reversed-Phase HPLC for Simultaneous Separation and Determination of Seven Antiepileptic Drugs and Two of their Active Metabolites in Human Plasma

A simple reversed-phase high-performance liquid chromatographic (HPLC) method has been developed for the simultaneous determination of the antiepileptic drugs (AEDs) zonisamide (ZNS), primidone (PRI), lamotrigine (LTG), phenobarbital (PB), phenytoin (PHT), oxcarbazepine (OXC), and carbamazepine (CBZ) and two of their active metabolites, monohydroxycarbamazepine (MHD) and carbamazepine 10,11-epoxide (CBZE) in human plasma. Plasma (100 μL) was pretreated by deproteinization with 300 μL methanol containing 20 μg mL⁻¹ propranolol hydrochloride as internal standard. HPLC was performed on a C₈ column (4.6 mm × 250 mm; particle size 5 μm) with methanol–acetonitrile–0.1% trifluoroacetic acid, 235:120:645 (v/v), as mobile phase at a flow rate of 1.5 mL min⁻¹. ZNS, OXC, and CBZ were monitored by UV detection at 235 nm, and PRI, LTG, MHD, PB, PHT, and CBZE by UV detection at 215 nm. Relationships between response and concentration were linear over the concentration ranges 1–80 μg mL⁻¹ for ZNS, 5–50 μg mL⁻¹ for PRI, 1–25 μg mL⁻¹ for LTG, 1–50 μg mL⁻¹ for MHD, 5–100 μg mL⁻¹ for PB, 1–10 μg mL⁻¹ for CBZE, 0.5–25 μg mL⁻¹ for OXC, 1–50 μg mL⁻¹ for PHT, and 1–25 μg mL⁻¹ for CBZ. Intra-day and inter-day reproducibility were adequate (coefficients of variation were ≤11.6%) and absolute recovery ranged from 95.2 ± 6.13 to 107.7 ± 7.76% for all the analytes; for the IS recovery was 98.69 ± 1.12%. The method was proved to be accurate, reproducible, convenient, and suitable for therapeutic monitoring of the nine analytes.     

Sensitive measurement of ultratrace phenols in natural water by purge-and-trap with in situ acetylation coupled with gas chromatography-mass spectrometry

A novel purge-and-trap method coupled with gas chromatography-mass spectrometry (GC-MS) is developed for the analysis of trace and ultratrace phenols based on their derivatization with acetic anhydride. Parameters affecting the extraction efficiency, such as purge temperature, concentration of sodium chloride, purge time, and volume of derivatization reagent, were investigated. The optimized conditions were addition of 150 μL acetic anhydride, purge time of 25 min at the purge temperature of 60 °C with 30% NaCl. The linear range was 0.2–100 μg L⁻¹ for phenols. The limits of detection (LODs) ranged from 0.08 to 0.15 μg L⁻¹ and the relative standard deviations (RSDs) for most of the phenols at the 10 μg L⁻¹level were below 10%. Natural water samples collected from a pool were successfully analyzed using the proposed method. The recovery of spiked water samples was 72.9–84.2%.     

A novel electrochemical method for the determination of trinitrophenol

In pH 5.5, 0.1 mol l⁻¹ HAc-NaAc buffer solution, trinitrophenol has been determined quantitatively with differential pulse voltammetry by detecting its reduction peak currents at the glassy carbon electrode. The detection sensitivity was enhanced significantly by the addition of the surfactant of cetyl pyridinium chloride, and the enhancement mechanism was also studied in detail. The linear calibration range was 8.0 × 10⁻⁷ to 2.0 × 10⁻⁴ mol l⁻¹, and the detection limit was established to be 1.9 × 10⁻⁷ mol l⁻¹. This method has been applied to the determination of trinitrophenol in water sample, and the recovery was from 97.6 to 103.5%.     

Development and validation of an HPLC method for the simultaneous determination of clozapine and desmethylclozapine in plasma of schizophrenic patients

Summary A high-performance liquid chromatographic method with amperometric detection has been developed for the determination of levels of clozapine (CLZ) and its active metabolite N-desmethylclozapine (DMC) in human plasma. The analysis was performed on a 5 μm C8 reversed phase column (150×4.6 mm i.d.), with acetonitrile-phosphate buffer (pH 3.5), as the mobile phase. The detection voltage was +800 mV and the cell and column temperature were 50°C. Linear responses were obtained between 2 ng mL⁻¹ and 100 ng mL⁻¹. Absolute recovery for both clozapine and desmethylclozapine exceeded 88% and the detection limit was 1 ng mL⁻¹. Repeatability, intermediate precision and accuracy were satisfactory. The method, which is rapid, sensitive and selective, has been applied to therapeutic drug monitoring in schizophrenic patients following administration of Leponex^? tablets. In 21 patients in steady state at a mean daily clozapine dosage of 358 mg (ranging from 150 to 500 mg day⁻¹), clozapine levels averaged 379 ng mL⁻¹ (ranging from 102 to 818 ng mL⁻¹) and DMC levels averaged 233 ng mL⁻¹ (ranging from 70 to 540 ng mL⁻¹). The method requires only a very small amount of plasma (100 μL), and thus it is suitable for pharmacokinetic studies, as well as for therapeutic drug monitoring.     

Development of a cloud point extraction and preconcentration method for silver prior to flame atomic absorption spectrometry

The possibility was investigated of using 2-mercaptobenzothiazole (MBT) for Ag(I) concentration by micellar extraction at cloud point (CP) temperature and subsequent determination by flame atomic absorption spectrometry (FAAS). The method is based on the complexation of Ag(I) with 2-mercaptobenzothiazole (MBT) in the presence of non-ionic micelles of Triton X-114. The effect of experimental conditions such as pH, concentration of chelating agent and surfactant, equilibration temperature and time on cloud point extraction was studied. Under the optimum conditions, the preconcentration of 10 mL of water sample in the presence of 0.1% Triton X-114 and 2 × 10⁻⁴ mol L⁻¹ 2-mercaptobenzothiazole permitted the detection of 2.2 ng mL⁻¹ silver. The calibration graph was linear in the range of 10–200 ng mL⁻¹, and the recovery of more than 99% was achieved. The proposed method was used in FAAS determination of Ag(I) in water samples.     

Catanionic surfactant ambient cloud point extraction and high-performance liquid chromatography for simultaneous analysis of organophosphorus pesticide residues in water and fruit juice samples

A mixed anionic–cationic surfactant cloud point extraction (CPE) has been developed using sodium dodecyl sulfate (SDS) and tetrabutylammonium bromide (TBABr) for the extraction and preconcentration of organophosphorus pesticides (OPPs) at ambient temperature before analysis by high-performance liquid chromatography. The studied OPPs were azinphos-methyl, parathion-methyl, fenitrothion, diazinon, chlorpyrifos, and prothiophos. The optimum conditions of the mixed anionic–cationic CPE were 50 mmol L⁻¹ SDS, 100 mmol L⁻¹ TBABr, and 10% (w/v) NaCl. The extracted OPPs were successfully separated within 11 min using the conditions of a Waters Symmetry C8 column, a flow rate of 0.8 mL min⁻¹, a gradient elution of methanol and water, and detection at 210 nm. Linearity was found over the range 0.05–5 μg mL⁻¹, with the correlation coefficients higher than 0.996. The enrichment factor of the target analytes was in the range 6–11, which corresponds to their limits of detection from 1 to 30 ng mL⁻¹. High precisions (intra-day and inter-day) were obtained with relative standard deviation <1.5% (t _R) and 10% (peak area). Accuracies (% recovery) of the different spiked OPP concentrations were 82.7–109.1% (water samples) and 80.3–113.3% (fruit juice samples). No contamination by the OPPs was observed in any studied samples.     

Quantification of cis-Abienol in Oriental Tobacco Leaves by LC

A rapid and accurate method for the quantification of cis-abienol in oriental tobacco leaves by normal phase liquid chromatography was developed. Freeze-dried tobacco samples were sonicated in methylene chloride for 10 min. The supernatant was purified using a silica gel solid phase extraction cartridge. Ten milliliter of the resulting methylene chloride eluate was collected, then separated on a 250 × 4.6 mm, 5 μm particle-size CN column with n-hexane: ethyl acetate, 100:2 (v/v) at a flow rate of 1 mL min⁻¹. cis-Abienol was detected by UV absorption at 254 nm. The linear range was from 2.14 × 10⁻⁴ to 4.28 × 10⁻² mg mL⁻¹ and the correlation coefficient was 1.000. The average recovery was 98.7, 105.2 and 103.1% in five replicated sets of tobacco samples spiked with 0.2856, 0.7140 and 1.904 mg cis-abienol. The relative standard deviations (RSDs) were 1.04, 0.63 and 1.25%, respectively (n = 5). Limit of detection (S/N = 3) was 21.84 μg g⁻¹ and limit of quantification (S/N = 10) was 72.80 μg g⁻¹. The method was found to be suitable for determination of cis-abienol in oriental tobacco leaves. Furthermore, pure cis-abienol used for method validation was obtained by preparative reversed phase high-performance liquid chromatography. Identification was performed by UV detection, nuclear magnetic resonance and mass spectrometry.     

Application of ICP-QMS for the determination of ultratrace-levels of <Superscript>226</Superscript>Ra in geothermal water and sediment samples

A rapid, accurate and less labor intensive approach to determining ²²⁶Ra in environmental samples was examined; this utilized quadrupole-based inductively coupled plasma mass spectrometry (ICP-QMS). The procedure used chemical separation by ion exchange chromatography to remove most of the matrices after coprecipitation with BaSO₄. The average chemical recovery of the NIST SRM preparation method ranged from 60.5 to 85.9% using ¹³³Ba as internal tracer by gamma counting. This technique was capable of completing a ²²⁶Ra measurement within 3 min. It did not require an in-growth period to allow radon and its progeny to achieve secular equilibrium with the parent ²²⁶Ra as is needed for liquid scintillation analyzer (LSA). The method detection limits for the determination of ²²⁶Ra in geothermal water and sediment samples were 0.02 mBq L⁻¹ (0.558 fg L⁻¹) and 0.10 Bq kg⁻¹ (2.79 fg g⁻¹), respectively. The results obtained with various natural samples and the suitability of the method when applied to various environmental matrices such as geothermal water and sediment are discussed. When ICP-QMS was compared to double-focusing magnetic sector field inductively coupled plasma mass spectrometry (ICP-SFMS), good agreement was obtained with a correlation coefficient, r ² = 0.982.     

Sequential spectrofluorimetric determination of free and total glycerol in biodiesel in a multicommuted flow system

A new procedure for spectrofluorimetric determination of free and total glycerol in biodiesel samples is presented. It is based on the oxidation of glycerol by periodate, forming formaldehyde, which reacts with acetylacetone, producing the luminescent 3,5-diacetyl-1,4-dihydrolutidine. A flow system with solenoid micro-pumps is proposed for solution handling. Free glycerol was extracted off-line from biodiesel samples with water, and total glycerol was converted to free glycerol by saponification with sodium ethylate under sonication. For free glycerol, a linear response was observed from 5 to 70 mg L⁻¹ with a detection limit of 0.5 mg L⁻¹, which corresponds to 2 mg kg⁻¹ in biodiesel. The coefficient of variation was 0.9% (20 mg L⁻¹, n = 10). For total glycerol, samples were diluted on-line, and the linear response range was 25 to 300 mg L⁻¹. The detection limit was 1.4 mg L⁻¹ (2.8 mg kg⁻¹ in biodiesel) with a coefficient of variation of 1.4% (200 mg L⁻¹, n = 10). The sampling rate was ca. 35 samples h⁻¹ and the procedure was applied to determination of free and total glycerol in biodiesel samples from soybean, cottonseed, and castor beans.