金属化聚邻甲苯胺膜修饰电极的性能研究

在聚邻甲苯胺 (POT)膜修饰电极上用电化学法沉积Pt微粒 ,由SEM与XRD表征其表面形态与晶面取向 ,同时研究异丙醇在金属化POT膜电极上的氧化行为 .结果表明 ,Pt在POT膜上的沉积呈现晶面择优取向的现象 ,况且POT质子掺杂后 ,由于电化学活性增强 ,影响了沉积铂微粒的尺寸和粒径分布 .异丙醇的电氧化可发生在POT的电化学活性区 ,当电位大于 0 .70V(SCE)时 ,POT不再呈氧化还原活性 ,异丙醇的电氧化主要在铂微粒上进行 .聚合物不仅作为铂微粒的载体而且自身参加反应 ,这种微异相催化体系需用新的模型描述     

金属化聚邻甲苯胺膜修电极的性能研究

在聚邻甲苯胺（POT）膜修饰电极上用电化学法沉积Pt微粒,由SEM与XRD表征其表面形态与晶面取向,同时研究异丙醇在金属化POT膜电极上的氧化行为。结果表明,Pt在POT膜上的沉积呈现晶面择优取向的现象,况且POT质子掺杂后,由于电化学活性增强,影响了沉积铂微粒的尺寸和粒径分布,异丙醇的电氧化可发生在POT的电化学活性区,当电位大于0．70V（SCE）时,POT不再呈氧化还原活性,异丙醇的电氧化主要在铂微粒上进行,聚合物不仅作为铂微粒的载体而且自身参加反应,这种微异相催化体系需用新的模型描述。     

铂微粒修饰的聚苯胺薄膜电极对甲醛氧化的电催化作用

以电位扫描法把铂微粒沉积在聚苯胺（ＰＡｎ）薄膜是上以制得铂微粒修饰的聚苯胺薄膜电极。该电极的催化活性以甲醛在０．５ｍｏｌ／Ｌ硫酸溶液中的电化学氧化测定。它集催化活性和电活性于一体，对甲醛在酸性介质中的电化学氧化显示了非常高的电催化活性。较之裸铂电极，ＰＡｎ薄膜电极，其催化电流提高１０倍。铂微粒的大小，分布和载量，甲醛的浓度，基体金属的种类等因素对电极材料的催化活性均有影响。     

聚苯胺衍生物膜修饰电极的电化学和催化性质

采用聚 2，5 二甲氧基苯胺（PDMAn）、聚邻甲苯胺（POT）膜修饰电极，以异丙醇（i P）氧化为模型反应，研究功能性膜电极的电催化性能.两种聚合物的伏安行为都表现为两对氧化还原峰；与镀铂的Pt电极比较，Pt金属化的PDMAn和POT修饰电极，大大提高了i P氧化电流密度，而且随着循环次数增加，氧化电流不断增大，表明功能性膜修饰电极具有较高的催化活性. POT修饰电极在较低的铂含量下就表现出对i P的强烈催化活性，而且对低浓度i P的氧化，具有较高的响应灵敏度；此外POT还具有良好的环境稳定性，可望成为一种具有实际应用前景的电化学传感器.     

水热氧化法制备γ-Mn2O3

研究了用电化学方法制备的铂微粒修饰的聚２,５二甲氧基苯胺电极对甲酸的电催化氧化,用ＳＥＭ、ＸＰＳ表征了这种电极材料的表面结构,结果表明,这种复合电极对甲酸在酸性介质中电化学氧化具有很高的催化活性,较之裸铂电极其催化电流提高１００多倍．循环伏安法制备的铂微粒较均匀地分布在聚合物上,其粒径大约为３００ｎｍ．研究了铂微粒载量、阴离子种类、反应温度和浓度等因素对电极催化活性的影响．     

环取代基对金属化聚苯胺衍生物膜修饰电极性能的影响

通过比较聚2，5－二甲氧基苯胺（PDMAn）、聚邻甲基苯胺（POT）和聚间氯苯胺（PmClAn）膜修饰电极的氧化还原电位、沉积在这3种聚合物上的铂微粒的表面形态与晶面取向以及异丙醇在分散Pt微粒的聚苯胺膜修饰电极上的氧化行为，从电子效应和立体效应探讨了聚合物电化学性质与环取代基的关系以及不同聚合基质对Pt沉积机理和有催化性能的影响,结果表明，在硫酸溶液中PDMAn膜修饰电极的氧化还原电位最负、POT次之、PmClAn最正，Pt在PDMAn和POT膜上的电沉积机理与在PmClAn膜上的不同，聚合物膜上沉积的Pt微粒呈现（200)晶面择优取向，其中POT膜上择优取向度最大，PDMAn次之，Pm-ClAn最小，异丙醇在金属化聚合物膜电极上的氧化电位取决于聚苯胺的本质，在POT膜修饰电极上异丙醇的电氧化主要发生在POT的活性电位区，而在PDMAn与PmClAn膜上的电氧化则主要发生在Pt上的氧化电位区，说明聚合物膜不仅作为Pt微粒的分散介质，而且本身有产生催化作用。     

咖啡酸玻碳修饰电极对烟酰胺腺嘌呤二核苷酸的电催化氧化

研究了咖啡酸修饰电极的制备、性质及对NADH的电催化作用。修饰电极在0．1mol/L PBS缓冲溶液中(pH7．0)于0．0～ 050V(vs.Ag／AgCl)电位范围内呈现一对氧化还原峰，式量电位(E^0‘‘)为 0．250V(vs．Ag／AgCl)。E^0‘‘随pH增加而朝负方向移动，pH在5．0～8．0范围内，其线性回归方程为E^0‘‘=0．6233-0．05996pH，R=0．9969。表观电极反应速率常数(Kb)为12．3s^-1。电极反应的电子数为2且有2个质子参与。该修饰电极对NADH的氧化具有很好的电催化作用。NADH浓度在0．1—6．0mmol／L．范围内与峰电流呈现良好的线性关系。文中对电催化过程进行了探讨。     

分子印刷技术铂微粒修饰电极及甲醇的电催化氧化

利用分子印刷技术(Molecular Imprinting Technology，MIT)，将铂微粒沉积到谷胱甘肽自组装膜的针孔上，并用循环伏安法研究了甲醇在该电极上的电催化氧化行为。实验结果表明，该电极对甲醇电化学氧化呈现出较高的催化活性，活性高低与载铂量、溶液pH值及电极表面铂微粒所处的微环境有关。     

葡萄糖在碳纳米管/纳米TiO2膜载Pt复合电极上的电催化氧化

用电化学循环伏安法和计时电位法研究了葡萄糖在碳纳米管／纳米TiO2膜载Pt(CNT／nano-TiO2／Pt)复合电极上的电催化氧化,结果表明,在碱性介质中CNT／nano-TiO2／Pt复合电极对葡萄糖的电氧化具有高催化活性,葡萄糖氧化峰电流密度高达13mA／cm^2,比铂电极上的增大一倍;复合电极性能稳定,抗中毒能力强,不易发生氧化振荡,是葡萄糖燃料电池和葡萄糖传感器的高活性催化电极。     

聚苯胺葡萄糖氧化酶电极的催化过程

用电化学方法固定在直径为0.5mm铂丝上的聚苯胺(PANI)葡萄糖(GOD)电极对葡萄糖有催化氧化作用.在0～-0.6V(vs.SCE)的电极范围内,在电极的循环伏安曲线上观察到与葡萄糖浓度有关的氧的还原峰和GOD还原态的氧化峰,用此GOD还原态的氧化峰电流可定量检测葡萄糖的浓度。本文提出在PANI电极上存在着酶反应氧化还原电荷直接传递的可能性。     

聚(2,5-二氧基苯胺)膜修饰电极的电化学及催化性质

二甲氧基苯胺;电沉积;氧化;化学修饰电极;聚(2;5-二氧基苯胺)膜修饰电极的电化学及催化性质     

PmClAn基膜修饰电极的电化学及催化性质研究

聚苯胺作为电极修饰材料 ,已在传感器上显示出广泛的应用前景[1～ 4 ] .异丙醇 ( i- P)氧化[5,6 ] 是个较简单的反应 ,被广泛作为电催化研究的模型反应 .目前 ,i- P电化学氧化的研究集中于 Pt的多晶或单晶电极[7～ 9] ,Gonzales等 [10 ] 报道了 Pt- Sn共沉积的 PAn膜修饰电极上的异丙醇电氧化 ,但对复合材料的微观结构仍欠研究 .本文讨论 Pm Cl An基质性质对 Pt电沉积的影响 ,并探讨了 i- P在沉积 Pt微粒的 Pm Cl An功能膜电极上的氧化情况 .1　实验部分1 .1　电极的制备　聚间氯苯胺 ( Pm Cl An,本征态 ud,HCl掺杂态 d)采用乳液聚…     

Experimental study of platinized poly-2,5-dimethoxyaniline electrodes

In the domains of chemical catalysis and analytical chemistry, the modification of metal electrodes by the deposition of multilayers was developed about twenty years ago. The purpose of our work was to compare the behavior of an electrode prepared with a substituted polyaniline with that of electrodes regularly used in analytical chemistry: platinum, platinized platinum and glassy carbon. We initially present results obtained with poly-2,5-dimethoxyaniline (PDMAn) on two classic systems: the couple Fe(CN)₆^3–/Fe(CN)₆^4– and the couple O₂/OH^–. The first example is often studied during training in electrochemistry because of the good results generally obtained. Levich’s equation is effectively well verified. On the other hand, reduction of oxygen and oxidation of OH^– ions are always limited by the rate of the electron transfer reactions. It seems to us that the study of the behavior of these two systems with platinum electrodes covered with PDMAn, platinized or not, could be interesting. The oxidation of isopropanol in a weakly acid medium was also investigated. In the field of analytical chemistry, a more detailed study is mandatory before deciding on the possibility of using electrodes modified with films of substituted polyaniline. An electrode, which would not be platinized, does not seem useful; the use of electrodes prepared with platinized polymers deposited on substrates less expensive than platinum, (glassy carbon for example), may be more interesting. It seems that H₂O₂ formation over a wide domain of potential would be the best result for oxidations and new experiments will be investigated.     

Investigation of ruthenium deposition onto a platinized platinum electrode in sulfuric acid media

Ruthenium deposition onto platinized Pt electrode in 0.5 M H₂SO₄ solution is investigated. The I–V profiles of the Pt electrode covered with Ru depend on the potential of Ru deposition. This phenomenon is explained by the increasing degree of oxidation of the Ru layers deposited at higher potentials. Oxidation of Ru deposited at low potentials begins with comparatively slow processes. A mechanism for Ru deposition via ionization of hydrogen adsorbed on platinized Pt electrode is proposed.     

纳米TiO2-Pt修饰电极的制备及其电催化活性

循环伏安;纳米TiO2-Pt修饰电极的制备及其电催化活性     

Characterization of stainless steel electrode modified by a thin film of polyaniline containing pt particles and its electrocatalytic activity for methanol oxidation

The catalytic behavior of stainless steel (SS) electrode modified by a thin film of polyaniline (PANI) containing platinum particles was studied for electrooxidation of methanol and compared with a platinated Pt/PANI electrode in acidic aqueous solution. Cyclic voltammetry (CV), chronoamperometry, CO stripping techniques were used to investigate electrochemical properties and electrocatalytic activity of SS/PANI/Pt and Pt/PANI/Pt electrodes. The morphology and particle size of Pt catalysts were characterized by Transmission Electron Microscopy (TEM) measurement. The effects of various parameters such as thickness of polymer film, medium temperature and stability of the modified electrodes on methanol oxidation were also investigated. The results indicated that the modified SS electrode exhibited a considerably high electrocatalytic activity on the methanol oxidation as well as the modified Pt electrode.     

Anodic Oxidation of Serine Anion on Smooth and Platinized Platinum

The anodic oxidation of serine anion on smooth (Pt) and platinized (Pt(Pt)) platinum electrodes is studied by the methods of cyclic and linear voltammetry, rotating disk electrode, coulometry, and reflectance IR spectroscopy. On both electrodes, the potential regions of electrochemical transformation of this amino acid are determined. It is shown that electrooxidation of serine proceeds with abstraction of 4 and 2 electrons on Pt and Pt(Pt) electrodes, respectively. It is found that the anodic oxidation of serine anions proceeds from the adsorbed state; a possible kinetic scheme of this process is proposed.