Environment-friendly bio-materials based on cotton-carbon aerogel for strontium removal from aqueous solution

Cotton carbon aerogel was prepared and used as a new water-insoluble adsorbent to remove strontium from aqueous solution. A comprehensive study on adsorption of strontium by cotton carbon aerogel was conducted regarding the effects of initial pH, temperature, initial strontium concentration, and contact time. The adsorbent was characterized by SEM. The results of regression analysis indicated that the adsorption process largely depends on the pH and temperature. The optimum pH range for adsorption process is 5–7. The maximum removal efficiency of strontium from aqueous solution was 60.16%. Moreover, cotton carbon aerogel adsorbent has good reusability before the fifth reuse.     

Removal of Congo Red dye from its aqueous solution using natural coagulants

The textile dyeing industry consumes large quantities of water and produces large volumes of wastewater from different processes in dyeing and finishing processes. The low-cost, easily available naturally prepared coagulants like Surjana seed powder (SSP), Maize seed powder (MSP) and Chitosan as an ideal alternative to recent expensive coagulant methods for Congo Red (CR) dye removal has been investigated in this study. Various process parameters like pH, coagulant dose, flocculation time and temperature and also its optimization were exploited. The maximum percentage CR removal was found to be 98.0, 94.5 and 89.4 for SSP, Chitosan and MSP, respectively, at pH 4.0, coagulant dose of 25 mg/l, flocculation time 60 min and temperature of 340 K. The Sludge Volume Index (SVI) and turbidity were calculated for these parameters including process optimization. SSP found more preferable for CR removal and Chitosan was a better coagulant, which corresponds to SVI than the other coagulants investigated.     

Effective removal of cation dyes from aqueous solution using robust cellulose sponge

Cellulose sponge was proposed to an attractive bio-absorbent owing to its highly efficient, low-cost, biodegradable, and renewable sourcing. In this work, the wasted cotton linter as raw materials, the highly porous and lightweight cellulose sponges were synthesized via a facile chemical crosslinking and freeze-drying process. The resultant cellulose sponge (CA) exhibited an interconnected three-dimensional porous structure through crosslinked with N,N′-methylene bisacrylamide (MBA), which was beneficial to remove organic dyestuffs. The effects of various factors including solution pH, contact time, initial dye concentration, and ionic strength on the adsorption behavior were investigated in detail. Herein, Langmuir isotherm models were selected to determine the adsorption capacity, and the maximum theoretical adsorption capacity for Methylene blue (MB) and Crystal violet (CV) was 123.46 and 76.63 mg/g, respectively. Particularly, the results of kinetic and thermodynamic tests showed that the adsorption performance was a spontaneous endothermic reaction and the adsorption process followed the pseudo-second-order kinetic. Furthermore, cellulose sponges could maintain maximum adsorption capacity even after twelve cycles. Therefore, the eco-friendly cellulose sponge would be a promising adsorbent for effective wastewater treatment.     

Functionalization of regenerated cellulose membrane via surface initiated atom transfer radical polymerization for boron removal from aqueous solution

In this study, an adsorptive membrane was prepared for efficient boron removal. Poly(glycidyl methacrylate) was grafted on the surfaces of the regenerated cellulose (RC) membrane via surface-initiated atom transfer radical polymerization, and N-methylglucamine was used to further react with epoxide rings to introduce polyhydroxyl functional groups, which served as the major binding sites for boron. The pristine and modified membranes were characterized by X-ray photoelectron spectroscopy (XPS), attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), dynamic water contact angle measurement, and scanning electron microscopy. It was shown that the designed functional groups were successfully grafted onto the RC membrane, and surface modification contributed to higher boron binding capability. The optimal pH range for boron adsorption was 4-8. Under a neutral pH condition, the maximum adsorption capacity of the modified membrane was determined to be 0.75 mmol/g, which was comparable with those of commercial resins. Studies of electrolyte influence indicated the formation of inner-sphere surface complexes on the membrane surface. The ATR-FTIR and XPS analyses showed that secondary alcohol and tertiary amine groups were mainly involved in boron adsorption, and tetrahedral boron complexes were found on the membrane surface.     

Geopolymeric adsorbents from fly ash for dye removal from aqueous solution

Adsorbents from coal fly ash treated by a solid-state fusion method using NaOH were prepared. It was found that amorphous aluminosilicate geopolymers would be formed. These fly ash-derived inorganic polymers were assessed as potential adsorbents for removal of some basic dyes, methylene blue and crystal violet, from aqueous solution. It was found that the adsorption capacity of the synthesised adsorbents depends on the preparation conditions such as NaOH:fly-ash ratio and fusion temperature with the optimal conditions being at 1.2:1 weight ratio of Na:fly-ash at 250-350 degrees C. The synthesised materials exhibit much higher adsorption capacity than fly ash itself and natural zeolite. The adsorption isotherm can be fitted by Langmuir and Freundlich models while the two-site Langmuir model producing the best results. It was also found that the fly ash derived geopolymeric adsorbents show higher adsorption capacity for crystal violet than methylene blue and the adsorption temperature influences the adsorption capacity. Kinetic studies show that the adsorption process follows the pseudo second-order kinetics.     

Adsorption of Congo red from aqueous solution onto calcium-rich fly ash

The adsorption of Congo red from solution was carried out using calcium-rich fly ash with different contact times, concentrations, temperatures, and pHs. While the amount of dye adsorbed per unit weight of fly ash increases with increasing concentration and temperature, it decreases slightly with increasing pH. The adsorption was between 93 and 98% under the conditions studied. Kinetic studies showed that the adsorption process obeyed the pseudo-second-order kinetic model. It was also determined that the adsorption isotherm followed Freundlich and Dubinin-Radushkevich models. From thermodynamic studies, it was seen that the adsorption was spontaneous and endothermic. Desorption studies suggested that desorption was 29.18% in the presence of 0.1 N HCl and was 47.21% in the presence of CH(3)COOH (50% v/v). This indicated that most of the dye was held by fly ash via chemisorption as well as ion exchange. Furthermore, FTIR study also shows that a chemisorption process occurs between CR and fly ash, probably indicating dye/fly ash complexing.     

Role of clay-based membrane for removal of copper from aqueous solution

The present study focuses on the fabrication of polysulfone (PSf)-clay minerals impregnated hybrid membrane for treatment of Cu (II) ions. Blending and phase inversion methods have been employed to develop clay-based membranes by the mixing of bentonite, sepiolite and zeolite in the matrix of PSf. Moreover, characterization of fabricated membranes was carried out using SEM, FTIR, zeta potential, pore size and water contact angle measurement. Adsorption and filtration experiments were conducted to evaluate the permeation performance of the membrane. Obtained results of permeation study reveal that the presence of clay minerals in the matrix of modified membrane not only increases the adsorption and rejection efficiency for Cu (II) but, it also improves the flux of pure water. Among all developed membranes, the membrane prepared by the mixing of zeolite demonstrates the highest adsorption (2.82 mg/g) and rejection value (97%) towards Cu (II) at low pressure (0.5 bar). Regeneration performance results confirm the reusability of membrane up to 3–5 cycles along with 82.5–90% metal recovery. Based on significant metal recovery, clay-based low-cost zeolite/PSf membrane could be used to remove Cu (II) from water at low pressure to replace current conventional membrane.     

Phenol removal from aqueous solution by carbon xerogel

Carbon xerogel (CX) was used for phenol adsorption from aqueous solution. CX was synthesized by sol?Cgel polycondensation of resorcinol with formaldehyde using sodium carbonate (Na₂CO₃) as catalyst. Then, it was dried by convective drying technique and pyrolyzed under inert atmosphere. Phenol adsorption kinetics was very fast, what was attributed to the presence of open pore structure. The kinetic studies showed that the adsorption process could be fitted to a pseudo-second-order model and the particle diffusion process is the rate-limiting step of the adsorption. The phenol removal was maximum and unaffected by pH changes when the initial pH of the phenol solution was in the range of 3?C8. The optimum adsorbent dose obtained for phenol adsorption onto CX was 0.075?g/50?cm³ solution. The Langmuir model described the adsorption process better than the Freundlich isotherm model and the monolayer adsorption capacity is 32?mg?g^?1. Among the desorbing solutions used in this study, the most efficient desorbent was EtOH (100?%) which released about 87?% of phenol bound with the CX.     

Amino-functionalized multi-walled carbon nanotubes for removal of cesium from aqueous solution

Journal of Radioanalytical and Nuclear Chemistry - Amino-functionalized multi-walled carbon nanotubes (MWCNTs) were synthesized by a simple, cost-effective method using 3-aminopropyltriethoxysilane...     

Ice-templated porous polymer/UiO-66 monolith for Congo Red adsorptive removal

Chitosan/MOF composite porous monolith used in water remediation as adsorbent can realize high-efficient removal of pollutant in water and facile recycling from water. However, dissolution of chitosan (without crosslinking) in acidic aqueous solution will cause breakage of composite monolith. Herein, we report a chitosan/UiO-66 monolith prepared by ice-templating method. Specially, a pre-crosslinking treatment (by glutaraldehyde) is employed before the monolith formation, which obviously boosts its stability in aqueous solution. The composite monolith is evaluated by SEM, N₂ adsorption, XRD, and batch adsorption tests for Congo Red (CR). The results show that the composite monolith possesses a typical ice-templating structure with hierarchical (mirco- / meso- and macro-) pores. UiO-66 particles are embedded on the surface of chitosan matrix, and the crystal structure of UiO-66 is not changed obviously by the crosslinking and freezing process. The composite monolith exhibits high adsorption efficiency (90% of CR was removed from its aqueous solution in 60 min) and the maximum adsorption capacity of 246.21 mg/g (derived from Langmuir model) can be reached. After adsorption, the monolith is collected by a facile procedure and recovered using ethanol for evaluating its reusability. After 4 cycles, the CR removal efficiency of the composite monolith still remains ~90% of the initial efficiency. This work demonstrates that the simple crosslinking procedure before monolith formation can ensure the intact shape of the chitosan/MOF monolith during adsorption.     

Design,synthesis and activity study of tyrosinase encapsulated silica aerogel (TESA) biosensor for phenol removal in aqueous solution

Tyrosinase encapsulated silica aerogel (TESA) was synthesized via an alcohol-free colloidal sol–gel route at room temperature and at neutral pH. Characterization on TESA indicated that 98% of enzyme was effectively loaded and located inside the aerogel network. TESA without solvent extraction showed higher tyrosinase activity than TESA extracted by amyl acetate/acetone (v/v:1/1). Stability of tyrosinase in TESA was enhanced towards extreme temperature, acidic and basic conditions. Optimization study indicates that 500 U enzyme/g silica aerogel; aged for 2 days, showed superior performance in the oxidation of catechol. The activity of TESA was remarkably enhanced; which was active at a wider temperature (up to 80 °C) and pH range (4–9). In contrast, free tyrosinase was totally inactive at these pH values and temperature >55 °C. TESA successfully removed about 90% of phenol in aqueous solution after 3 h of contact time with excellent reusability.     

The removal of pharmaceutical pollutants from aqueous solution by Agro-waste

Pharmaceuticals are a unique class of emerging contaminants owing to their intrinsic ability to induce physiological effects on man and animals at low concentrations. Pharmaceuticals are released into the environment via diverse routes; human and animal wastes are the major sources. The persistence and mode of action of pharmaceuticals in the environment make them a major concern. Among methods available for wastewater treatment, the adsorption technique is found to be effective and easy to operate. The expensive nature of commercial activated carbons, however, created a limitation to the adsorption technique; hence the exploration for low-cost and sustainable adsorbents for the removal of different categories of water contaminants. Agricultural wastes offer such advantages as low-cost, abundance and eco-friendly materials in adsorbent preparation. Herein presented are the category and classes of pharmaceuticals cum the risks associated with pharmaceuticals released into the environment. The chemistry of activated carbon/agro wastes viz-a-viz suitability and potency in adsorption of different pharmaceutical waste removal were reviewed; the benefits associated with agricultural wastes usage in pharmaceutical removal have also been presented. Various challenges, gaps cum research prospects in the current field of discussion are herein presented. This work will serve as a tool for public education and enlightenment, help environmentalists make plans for envisaged threats and serve as a guide for policy makers.     

Adsorptive removal of uranium from aqueous solution using chitosan-coated attapulgite

Chitosan-coated attapulgite beads were prepared by coating chitosan on naturally and abundantly available attapulgite, and made into spherical beads to adsorb uranium from aqueous solutions. The beads were characterized by SEM, EDS and FT-IR. The characteristics of beads of adsorbing uranium(VI) from aqueous solutions were studied at different conditions of pH, initial uranium concentration, contact time, biomass dosage and temperature. The pseudo-second order rate equation was used to describe the kinetic data, and isotherm data were fitted to Langmuir and Freundlich adsorption models. Thermodynamic parameters (ΔG°, ΔH°, and ΔS°) of the biosorption were also calculated. Thermodynamic parameters of the CAAB, viz., ΔG°(308 K), ΔH°, and ΔS° were determined to be −21.59, 6.29l and 90.51 J/mol K, respectively. The experimental results demonstrate that the beads of chitosan coated onto attapulgite exhibit considerable potential for application in both adsorption and removal of uranium from aqueous solutions.     

苯胺在碳纳米管上的吸附特征

苯胺是一种重要的有机化工原料,能通过皮肤和呼吸道进入人体而引起中毒,还会严重污染环境。目前,国内外处理含苯胺废水的方法主要有氧化法、萃取法、生化法、吸附法等。本文使用碳纳米管进行液相吸附除去苯胺。     

Modification of microcrystalline cellulose with pyridone derivatives for removal of cationic dyes from aqueous solutions

Microcrystalline cellulose (MCC) was modified with pyridone derivatives such as pyridone diester (PDE) and pyridone diacid (PDA) by using succinic acid anhydride as a linker. The modified MCCs were characterized by the fourier transform infrared spectroscopy, scanning electron microscopy, thermal gravimetric analysis, elemental analysis and solid state ¹³C NMR. The adsorption capacities of the modified MCCs to cationic dyes were examined by using methylene blue (MB) as a model dye. It was found that the kinetic adsorption data followed the pseudo-second-order kinetic model, and the adsorption equilibriums were reached less than 10 min. The isothermal adsorption data were fitted with the Langmuir isotherm model very well, from which the maximum adsorption capacities of the MCCs modified with PDE and PDA were determined to be 101.01 and 142.86 mg/g, respectively. Further investigation showed that the modified MCCs were pH-dependent for adsorption of MB in aqueous solutions. The modified MCCs could be used for removal of MB from an aqueous solution at pH 8, and reused by regeneration in an acidic solution. It was tested that the modified MCCs had a high reusability for removal of MB from aqueous solutions, and still maintained high adsorption capacities even after multiple cycles of desorption–adsorption processes. Hence, the MCCs modified with PDE and PDA could be an effective and efficient approach to removal of cationic dyes from aqueous solutions.     

Hydrogels prepared from unsubstituted cellulose in NaOH/urea aqueous solution

Novel cellulose hydrogels were synthesized through a "one-step" method from cellulose, which was dissolved directly in NaOH/urea aqueous solution, by using epichlorohydrin as crosslinker. Structure and properties of the hydrogels were characterized by using SEM, NMR, and water absorption testing. The hydrogels are fully transparent and display macroporous inner structure. The equilibrium swelling ratios of the hydrogels in distilled water at 25 degrees C are in the range from 30 to 60 g H(2)O/g dry hydrogel. Moreover, the reswelling water uptake of the hydrogels could be achieved to more than 70% compared with their initial swelling states. This work provided a simple and fast method for preparing eco-friendly hydrogels from unsubstituted cellulose.     

Amin-functionalized magnetic-silica core-shell nanoparticles for removal of Hg2+ from aqueous solution

Magnetic nanoparticles with monodisperse shape and size were prepared by a simple method and covered by silica. The prepared core-shell Fe₃O₄@silica nanoparticles were functionalized by amino groups and characterized by scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer-Emmett-Teller (BET) and Fourier transform infrared spectroscopy (FT-IR) techniques. The synthesized nanoparticles were employed as an adsorbent for removal of Hg²⁺ from aqueous solutions, and the adsorption phenomena were studied from both equilibrium and kinetic point of views. The adsorption equilibriums were analyzed using different isotherm models and correlation coefficients were determined for each isotherm. The experimental data were fitted to the Langmuir–Freundlich isotherm better than other isotherms. The adsorption kinetics was tested for the pseudo-first-order, pseudo-second-order and Elovich kinetic models at different initial concentrations of the adsorbate. The pseudo-second-order kinetic model describes the kinetics of the adsorption process for amino functionalized adsorbents. The maximum adsorption occurred at pH 5.7 and the adsorption capacity for Fe₃O₄@silica-NH₂ toward Hg²⁺ was as high as 126.7 mg/g which was near four times more than unmodified silica adsorbent.     

Thiocyanate removal from aqueous solution by a synthetic hydrotalcite sol

The use of a chloride-containing synthetic hydrotalcite sol (LDHC) as adsorbent to remove thiocyanate from aqueous solution was investigated. LDHC was prepared by coprecipitation and was characterized by HRTEM, particle size, XRD, and FTIR. The experiments showed that LDHC was particularly effective in removing thiocyanate due to its small particle size and high zeta potential. The adsorption of thiocyanate on LDHC was favored when the initial solution pH was in the range 3-10, though the most effective pH range was between 4.0 and 8.0. The adsorption reached equilibrium within 150 min. The interaction between the surface sites of LDHC and thiocyanate ions may be a combination of both anion exchange and surface complexation. The pseudo-second-order model best described the adsorption kinetics of thiocyanate onto LDHC. The equilibrium isotherm showed that the adsorption of thiocyanate on LDHC was consistent with the Langmuir equation and the saturated adsorption capacity of LDHC for thiocyanate was 98.3 mg/g at 20°C. The regenerated LDHC in FeCl(3) solution can be used repeatedly in adsorption-regeneration cycles. The results showed that LDHC can be used as a new adsorbent for thiocyanate removal from aqueous solution because of its high adsorption capacity and rapid adsorption rate.     

Kinetic study of spiramycin removal from aqueous solution using heterogeneous photocatalysis

Spiramycin macrolide antibiotic (SPM) can be photocatalytically degraded on TiO₂ (anatase variety). The experiments are done in a batch reactor and the effect of some key parameters is investigated under low energy of artificial UV light. The reaction rate is affected by varying TiO₂ dose, pH and SPM concentration. Under optimized conditions, a photodegradation efficiency of 98% is achieved and the SPM photodegradation follows pseudo-first order kinetics. The Langmuir–Hinshelwood (L–H) model is successfully used to fit the experimental data, indicating the dependence of the reaction rate on the chemical reaction step. The L–H model led to the determination of both reaction kinetic and adsorption/desorption equilibrium constants. In order to give an overall estimate of the by-products, chemical oxygen demand, total organic carbon, and calculated average oxidation state monitor the photodegradation process.