Analysis of carbohydrates in wood and pulps employing enzymatic hydrolysis and subsequent capillary zone electrophoresis

An efficient method for determining the carbohydrate composition of extractive-free delignified wood and pulp is described here. The polysaccharides in the sample are first hydrolyzed using a mixture of commercially available preparations of cellulase and hemicellulase. The reducing saccharides in the hydrolysate thus obtained are subsequently derivatized with 4-aminobenzoic acid ethyl ester and thereafter quantitated by capillary zone electrophoresis (CZE) in an alkaline borate buffer with monitoring of the absorption at 306 nm. All reducing sugars (i.e., neutral monosaccharides and uronic acids) which occur as structural elements in the polysaccharides of wood and pulp can be quantitated in a single such analytical run, which can also determine the contents of 4-deoxy-beta-L-threo-hex-4-enopyranosyluronic acid (HexA) residues present in pulps obtained from alkaline processes. CZE analyses were performed using linear regression of standard curves over a concentration range spanning approximately three orders of magnitude. Carbohydrate constituents constituting approximately 0.1% of the dry mass of the sample could be quantitated. The overall precision of this analytical procedure--involving enzymatic hydrolysis, derivatization and CZE--was good (RSD=2.2-7.5%), especially considering the heterogeneity of the wood and pulp samples. The total yield of carbohydrates (93-97%) obtained employing the procedure developed here was consistently higher than that obtained upon applying the traditional procedure for carbohydrate analysis (85-93%) (involving acid hydrolysis and gas chromatographic analysis) to the same pulps. The trisaccharide HexA-xylobiose was the only HexA-containing saccharide detected using the conditions for enzymatic hydrolysis developed here (i.e., 30 h incubation at pH 4 and 40 degrees C); whereas mixtures of HexA-xylobiose and HexA-xylotriose were obtained when the incubation was performed at pH 5 or 6.     

Compression molded wood pulp biocomposites: a study of hemicellulose influence on cellulose supramolecular structure and material properties

In this study, the importance of hemicellulose content and structure in chemical pulps on the property relationships in compression molded wood pulp biocomposites is examined. Three different softwood pulps are compared; an acid sulfite dissolving grade pulp with high cellulose purity, an acid sulfite paper grade pulp and a paper grade kraft pulp, the latter two both containing higher amounts of hemicelluloses. Biocomposites based the acid sulfite pulps exhibit twice as high Young’s modulus as the composite based on paper grade kraft pulp, 11–12 and 6 GPa, respectively, and the explanation is most likely the difference in beating response of the pulps. Also the water retention value (WRV) is similarly low for the two molded sulfite pulps (0.5 g/g) as compared to the molded kraft pulp (0.9 g/g). The carbohydrate composition is determined by neutral sugar analysis and average molar masses by SEC. The cellulose supramolecular structure (cellulose fibril aggregation) is studied by solid state CP/MAS ¹³C-NMR and two forms of hemicellulose are assigned. During compression molding, cellulose fibril aggregation occurs to higher extent in the acid sulfite pulps as compared to the kraft pulp. In conclusion, the most important observation from this study is that the difference in hemicellulose content and structure seems to affect the aggregation behaviour and WRV of the investigated biocomposites.     

The effect of chemical and physical characteristics of spruce SEW pulps on enzymatic hydrolysis

Conifers, which are the most abundant biomass species in Nordic countries, USA, Canada and Russia, exhibit strong resistance towards depolymerization by cellulolytic enzymes. At present, it is still not possible to isolate a single structural feature which would govern the rate and degree of enzymatic hydrolysis. On the other hand, the forest residues alone represent an important potential for biochemical production of biofuels. In this study, the effect of substrate properties on the enzymatic hydrolysis of softwood was studied. Stem wood spruce chips were fractionated by SO₂–ethanol–water (SEW) treatment to produce pulps of varying composition by applying different operating conditions. The SEW technology efficiently fractionates different types of lignocellulosic biomass by rapidly dissolving hemicelluloses and lignin. Cellulose remains fully in the solid residue which is then treated by enzymes to release glucose. The differences in enzymatic digestibility of the spruce SEW pulp fibers were interpreted in terms of their chemical and physical characteristics. A strong correlation between the residual lignin content of SEW pulp and enzymatic digestibility was observed whereas cellulose degree of polymerization and hemicellulose content of pulp were not as important. For the pulps containing about 1.5 % (w/w) lignin, 90 % enzymatic digestibility was achieved at 10 FPU enzyme charge and 24 h of hydrolysis time.     

Changes in cellulose supramolecular structure and molecular weight distribution during steam explosion of aspen wood

We have studied the cellulose supramolecular structure in pulps obtainedby steam explosion of aspen wood. The pulps were bleached with hydrogenperoxidein an OQP-sequence and characterised by size exclusion chromatography and¹³C cross polarisation magic angle spinning (CP/MAS)NMR-spectroscopy. With CP/MAS-NMR-spectroscopy and chemometrics we were able toseparate the supramolecular structural changes taking place during steamexplosion into two independent processes. One process was related to the extentof processing and showed degradation and dissolution of cellulose,hemicelluloseand lignin accompanied by an increase in cellulose content. The second processwas displayed by pulps having molecular weights below approximately 100000 andwas interpreted as showing the removal of dislocations and an increase incrystalline and/or paracrystalline cellulose in the cellulose fibrils.     

Pretreatment of wood by UCT-solvent for the enzymatic hydrolysis

UCT-solvent pretreatment was carried out on woods (beech and akamatsu (pine)) for the enzymatic hydrolysis, in which pretreatment the ground woods were autoclaved with a mixture of water and cyclo-hexanol (37.5% vol% cyclohexanol) having upper critical temperature (UCT: 184°C) on the mutual solubility curve (named as UCT-solvent). Ninety-five and 92% of Klason lignin were removed from beech and akamatsu, respectively, whereas when the woods were autoclaved with water instead of UCT-solvent, only 43 and 18% of Klason lignin was removed from them, respectively. The excellent ability of UCT-solvent for the removal of Klason lignin is owing to that the solvent disturbs re-coupling between the degradation products. The enzymatic hydrolysis of wood was much improved by UCT-solvent pretreatment: the hydrolytic reactivity of akamatsu was enhanced by 2.8 times comparing with when akamatsu was pretreated with water instead of UCT-solvent.     

The solvated fluoride anion can be a good nucleophile

Computations show how the solvated fluoride ion can be a good nucleophile in spite of its high solvation energy.     

NMR evidence of a supramolecular structure of water

The hypothesis advanced in this paper is based on the formation of dissipative structures, in the form of supramolecular structures of water, by virtue of its hydrogen bonds, structurally similar to a liquid crystal. The supramolecular structure could be a macromolecule typical of a living organism (plant or animal), which as we know is approximately 80% water, with a complex conformation induced initially by an active principle and which remains, organising itself as a result of an input of energy (dynamisation, electromagnetic wave or other). Water is the most abundant substance on earth and has been very well studied with a number of model structures having been proposed and refined. Notwithstanding this, it remains an anomalous liquid where no single model is able to explain all of its properties. Recently our research group in Siena carried out NMR studies on the water molecule measuring nuclear spin relaxation times T1 and T2. The phenomena observed lead to the conclusion that water and aqueous solutions should be regarded as continuous polymorphous self-organizing systems. At the macro-level the water behaviour is related with biodiversity, the core of biological evolution.     

Three distinct read-out modes for enzyme activity can operate in a semi-wet supramolecular hydrogel

Assays of hydrolytic enzyme activity, such as of glycosidases and phosphatase, as well as several proteases, using a semi-wet supramolecular hydrogel array composed of a glycosylated amino acetate are described. It has been demonstrated that the microcavity formed by gel fibrils is suitable to immobilize native enzymes without denaturation under semi-wet conditions, and thus the nanofiber has been rationally used as a sensing domain to monitor enzymatic reactions. By using a fluorogenic substrate, reducing the size of the hydrogel can significantly improve the problem of suppressed diffusion within the gel matrix thus making the hydrogel a promising semi-wet matrix for evaluating enzyme activity. Confocal laser scanning microscopy observations have shown that an environmentally sensitive fluorescent probe accumulates in the hydrophobic domain of the gel fiber and emits fluorescence more strongly upon hydrolytic cleavage of the substrate peptides. Not only a simple environmentally sensitive probe but also a FRET (fluorescence resonance energy transfer)-type read-out mode can be devised to analyze the enzymatic hydrolysis-triggered redistribution of the probe between the nanospace and the nanofiber to accomplish a more clearly distinguished enzyme assay. Thus, it is clear that three distinct read-out modes, that is, 1) fluorogenic substrates, 2) substrates bearing an environmentally sensitive probe, or 3) a substrate exhibiting FRET, can operate under the semi-wet hydrogel conditions used in these investigations. In addition, owing to the unique properties of the present supramolecular hydrogel in semi-wet conditions, that is, its phase-segregation properties and dynamics, the supramolecular substrate/enzyme array has successfully been used for high-throughput screening of single and multiple enzymes based on their activity, lysate analysis, and quantitative evaluation of inhibitor potency and selectivity.     

The contribution of complementary hydrogen bonding to supramolecular structure

Two different types of complementary hydrogen bonding contribute to the formation and temperature dependent behavior of a pseudo[2]rotaxane dimer.     

The supramolecular structure of ultrafiltration membranes synthesized by electropolymerization

The structure and morphology of polyacrylamide-formaldehyde ultrafiltration membranes synthesized by electropolymerization of monomers have been investigated by scanning electron microscopy and scanning tunneling microscopy. The conclusion is that the polymeric film consists of crystalline and amorphous phases. Spherulites occur throughout the entire thickness of the membrane matrix and make the whole structure rigid. The amorphous phase is penetrated by pores directed perpendicularly to the membrane surface. The membranes have an anisotropic sandwich structure with the selective layer formed on the side of the polymer film facing the electrode.     

Computational study of a chiral supramolecular arrangement of organic structure directing molecules for the AFI structure

Molecular mechanics computational methods have been employed to study the structure directing effect of S-(-)-1-benzyl-2-pyrrolidiniummethanol molecules towards microporous aluminophosphate materials with the AFI structure. These chiral molecules form dimers inside the one-dimensional AFI channel, which are the active structure-directing agents in the synthesis. Four different conformers of the S-(-)-1-benzyl-2-pyrrolidiniummethanol molecule are in principle available; of these, the S,S-trans shows a marked stability in dimeric form. Self-assembly between adjacent dimers generates a helicoidal, and hence chiral arrangement of the organic molecules, which extends with the same direction of rotation through the whole solid, and may thus be employed to introduce chirality in the microporous material.     

The effect of chemical composition on microfibrillar cellulose films from wood pulps: water interactions and physical properties for packaging applications

The interactions with water and the physical properties of microfibrillated celluloses (MFCs) and associated films generated from wood pulps of different yields (containing extractives, lignin, and hemicelluloses) have been investigated. MFCs were produced by combining mechanical refining and a high pressure treatment using a homogenizer. The produced MFCs were characterized by morphology analysis, water retention, hard-to-remove water content, and specific surface area. Regardless of chemical composition, processing to convert macrofibrils to microfibrils resulted in a decrease in water adsorption and water vapor transmission rate, both important properties for food packaging applications. After homogenization, MFCs with high lignin content had a higher water vapor transmission rate, even with a higher initial contact angle, hypothesized to be due to large hydrophobic pores in the film. A small amount of paraffin wax, less than 10%, reduced the WVTR to a similar value as low density polyethylene. Hard-to-remove water content correlated with specific surface area up to approximately 50 m²/g, but not with water retention value. The drying rate of the MFCs increased with the specific surface area. Hornified fibers from recycled paper also have the potential to be used as starting materials for MFC production as the physical and optical properties of the films were similar to the films from virgin fibers. In summary, the utilization of lignin containing MFCs resulted in unique properties and should reduce MFC production costs by reducing wood, chemical, and energy requirements.     

Study of a supramolecular structure of continental type petroleum asphaltenes

Supramolecular, electronic, and chemical structures of petroleum asphaltene molecules are studied. The investigations are carried out by quantum chemistry and molecular mechanics methods. The quantum chemical calculation of the structure-chemical parameters of dimers and trimers of petroleum asphaltenes is made using DFT/B3LYP. The refined values of the ionization potential and electron affinity of petroleum asphaltene molecules, their dimers and trimers agree well with the electron spectroscopy data. The results of the study of geometric structures of petroleum asphaltene dimers and trimers confirm the non-planar structure of asphaltenes.     

The structure factor for liquid lead

Abstract

The structure factor for liquid lead at the temperatures 613 K, 643 K, 863 K and 1163 K are measured by neutron diffraction. Extensive comparisons to earlier measurements are made as well as comparisons to different hard-core models.     

Formation of a molecular spin ladder induced by a supramolecular cation structure

A novel molecular spin ladder structure of a nickel dithiolate complex has been constructed using a supramolecular cation composed of anilinium and 18-crown-6.     

Toward the supramolecular structure of collagen: a molecular dynamics approach

The structure, stability, and conformational dynamics of an assembly of two pentameric bundles made of collagen-like triple helical segments are explored using 1.2 ns molecular dynamics simulations in three environments: 8.0% (v/v) formaldehyde/water solution, 1.4% (v/v) gallic acid/water solution, and pure water. Stable supramolecular arrangements, where the two collagen units are very close to each other at interacting distances, are identified via docking and energy minimization procedures. Analysis of the interaction with formaldehyde and gallic acid suggests that they perturb the protein in a similar way depending on hydrogen-bonding capability, hydrophobic association properties, and the size and concentration of the compound.     

The secondary structure of a membrane-modifying peptide in a supramolecular assembly studied by PELDOR and CW-ESR spectroscopies.

The new technique of pulsed electron-electron double resonance in electron spin-echo (PELDOR) in combination with the CW-ESR method has been used to investigate the secondary structure of a double spin-labeled peptide (the [TOAC-1,8]-analogue of the peptaibol antibiotic trichogin GA IV) that is hidden into a tetrameric supramolecular assembly of unlabeled peptide molecules. The magnetic dipole-dipole relaxation of spin labels has been experimentally studied in glassy solutions of the double-labeled peptide frozen to 77 K in a mixture of chloroform-toluene with an excess of unlabeled peptide. The PELDOR signal oscillations have been observed at high degrees of dilution with unlabeled peptide. The intramolecular distance between the spin labels of the peptide molecule in the aggregate has been determined from the oscillation frequency to be 15.7 A which is close to the value of (approximately equal to) 14 A calculated for a 3(10)-helical structure. Estimation of the fraction of this ordered secondary structure shows that about 19% of the peptide molecules in aggregates are folded in the 3(10)-helical conformation. The present experimental results are consistent with our molecular model presented in J. Am. Chem. Soc. 2000, 122, 3843-3848, wherein four amphiphilic 3(10)-helical peptide molecules form a vesicular system with the polar amino acid side chains pointing to the interior, and the apolar side chains, to the exterior of the cluster. The experimental data were compared with the results obtained with other techniques.     

The influence of the supramolecular structure of water on the kinetics of vaporization

The kinetics of water vaporization was studied gravimetrically using a Q-1500 D derivatograph with an accuracy of ±5 × 10^?5 g under atmospheric conditions. Various supramolecular structures were created in liquid water using solutions of K, Na, Ba, and Zn chlorides with various concentrations. The kinetic dependences of weight P loss caused by the vaporization of solutions were compared with the data on pure water used to prepare the solutions. The dependence of the rate of vaporization V on the concentration of hydrated ions in solutions was used to show that the rate V is the sum of the rates of vaporization of particles of two types, (a) H₂O molecules and (b) supramolecular formations (H₂O clusters) with H-bonds. As a consequence, a nonlinear (piecewise linear) dependence of the kinetics of vaporization P = f(τ) of water and solutions is observed. The rate of vaporization (V ₁) along the initial P = f(τ) curve portions is substantially (by ～30%) higher than its stationary value (V).