BaTiO3-BaAl2O4-Al2O3复合载体的制备、表征及其Ni基催化剂催化CH4/CO2重整反应性能

以十六烷基三甲基溴化胺为结构导向剂,采用溶胶-凝胶法制备了BaTiO3-BaAl2O4-Al2O3复合载体,采用X射线衍射、红外光谱、N2吸附-脱附、透射电子显微镜和H2程序升温还原等技术对复合载体进行了表征,并以CH4/CO2重整制合成气为探针反应,考察了不同Ni/BaTiO3-BaAl2O4-Al2O3催化剂的性能.结果表明,BaTiO3-BaAl2O4-Al2O3复合载体具有多孔织构特性和较高的比表面积,BaTiO3和BaAl2O4以晶粒状态分布在复合载体的内外表面,晶粒尺寸在20～50nm的范围,复合载体孔径为10～20nm.复合载体上BaTiO3和BaAl2O4的引入,适度削弱了Ni/BaTiO3-BaAl2O4-Al2O3催化剂中Ni物种与γ-Al2O3间的强相互作用,抑止了NiAl2O4尖晶石的生成;当载体中Ba(Ti)含量为17.33%时,其负载的Ni催化剂上CH4/CO2重整制合成气反应的活性和稳定性最高.     

Electronic structure of a low-spin heme/Cu peroxide complex: spin-state and spin-topology contributions to reactivity

This study details the electronic structure of the heme–peroxo–copper adduct {[(F8)Fe(DCHIm)]-O2-[Cu(AN)]}+ (LS(AN)) in which O2(2–) bridges the metals in a μ-1,2 or “end-on” configuration. LS(AN) is generated by addition of coordinating base to the parent complex {[(F8)Fe]-O2-[Cu(AN)]}+ (HS(AN)) in which the O2(2–) bridges the metals in an μ-η2:η2 or “side-on” mode. In addition to the structural change of the O2(2–) bridging geometry, coordination of the base changes the spin state of the heme fragment (from S = 5/2 in HS(AN) to S = 1/2 in LS(AN)) that results in an antiferromagnetically coupled diamagnetic ground state in LS(AN). The strong ligand field of the porphyrin modulates the high-spin to low-spin effect on Fe–peroxo bonding relative to nonheme complexes, which is important in the O–O bond cleavage process. On the basis of DFT calculations, the ground state of LS(AN) is dependent on the Fe–O–O–Cu dihedral angle, wherein acute angles (<~150°) yield an antiferromagnetically coupled electronic structure while more obtuse angles yield a ferromagnetic ground state. LS(AN) is diamagnetic and thus has an antiferromagnetically coupled ground state with a calculated Fe–O–O–Cu dihedral angle of 137°. The nature of the bonding in LS(AN) and the frontier molecular orbitals which lead to this magneto-structural correlation provide insight into possible spin topology contributions to O–O bond cleavage by cytochrome c oxidase.     

Pt/Co3O4/3DOM Al2O3：甲苯燃烧的高效催化剂

与硫氧化物、氮氧化物、一氧化碳以及悬浮颗粒一样,大部分挥发性有机物(VOCs)污染大气环境.控制 VOCs排放有多种方法,其中催化氧化法是一种有效技术,关键在于获得高效催化剂.
　　近年来,负载过渡金属和贵金属催化剂因具有比单纯负载贵金属和单纯负载过渡金属氧化物更好的催化性能而备受关注.在负载贵金属催化剂中,高比表面积载体负载 Pt, Pd或 Rh催化剂得到广泛而深入的研究,尽管这些催化剂成本较高,但是其对 VOCs氧化反应显示了很高的低温催化活性.众所周知,催化活性取决于贵金属和 VOCs的种类,不同负载贵金属催化剂对特定反应会表现出不同的催化活性.负载 Pt催化剂对长链碳氢化合物和芳香族化合物氧化反应表现出更高的活性.相对于负载贵金属催化剂,负载过渡金属氧化物催化剂不仅具有良好的氧化活性,而且价格低廉.迄今已发现许多过渡金属氧化物(如 Co3O4, Cr2O3和 MnO2等)对典型 VOCs氧化反应具有催化活性,其中 Co3O4的催化活性尤为突出.研究表明, Co3O4的性质和分散度是决定其性能的关键因素,制备方法、载体性质和过渡金属氧化物负载量对 Co3O4的物化性质具有重要影响,而且在负载 Pt催化剂中添加金属氧化物能改善其催化性能.尽管多孔氧化铝是一种常用的载体材料,但目前尚无文献报道三维有序大孔-介孔氧化铝负载 Co3O4和 Pt纳米粒子催化剂的制备及其对甲苯氧化反应的催化性能.
　　本文采用聚甲基丙烯酸甲酯微球胶晶模板法、等体积浸渍法和聚乙烯醇保护的硼氢化钠还原法制备了三维有序大孔-介孔(3DOM Al2O3)负载 Co3O4和 Pt (xPt/yCo3O4/3DOM Al2O3, Pt的质量分数(x%)为0-1.4%, Co3O4的质量分数(y%)为0-9.2%)纳米催化剂.通过电感耦合等离子体原子发射光谱、X射线衍射、氮气吸附-脱附、扫描电子显微镜、透射电子显微镜、选区电子衍射、X射线光电子能谱及氢气程序升温还原等技术表征了催化剂的物化性质,利用固定床微型石英反应器评价了催化剂对甲苯氧化反应的催化活性.结果表明,xPt/yCo3O4/3DOMAl2O3催化剂具有多级孔结构(大孔孔径为180–200 nm,介孔孔径为4–6 nm),比表面积为94?102 m2/g.粒径为18.3 nm的 Co3O4纳米粒子和粒径为2.3?2.5 nm的 Pt纳米粒子均匀分散在3DOM Al2O3表面.在xPt/yCo3O4/3DOM Al2O3催化剂中,1.3Pt/8.9Co3O4/3DOM Al2O3拥有最高的 Oads浓度、最好的低温还原性和最高的甲苯氧化反应催化活性(当空速为20000mL g–1 h–1时,甲苯转化率达90%的反应温度为160oC).基于催化剂的活性数据和结构表征,我们认为,1.3Pt/8.9Co3O4/3DOM Al2O3优异的催化性能与其高分散的 Pt纳米粒子、高的 Oads浓度、好的低温还原性、Pt和 Co3O4纳米粒子间的强相互作用以及多级孔结构相关.     

Spektralphotometrische Bestimmung von schwerem Wasser in H2O/D2O-Gemischen im nahen Infrarot

Three different methods are described for the determination of D₂O in H₂O/D₂O mixtures by means of IR absorption. Wave-lengths, concentration ranges and accuracies are as follows: 2500 nm: 99–100 Mol-% D₂O, ±0.001%; 1670 nm: 0–20 Mol-% D₂O, ±0.02%; 1368 nm: 0–100% D₂O, ±0.1%. The methods are simple and rapid and have been successfully used for several years.     

负载型La0.8Sr0.2MnO3燃烧催化剂的载体效应

Combustion catalysts La0.8Sr0.2MnO3 supported on γ-Al2O3, α-Al2O3, cordierite (2MgO•2Al2O3•5SiO2) and ZrO2 were compared. Further investigation was focused on LSM/ γ-Al2O3 catalyst. It was observed that LSM/γ－Al2O3 catalyst loaded with 20% (mass fraction) LSM (La0.8Sr0.2MnO3 or corresponding oxides), heated at 750℃ or above, perovskite-type oxides were found by XRD examination, whereas, the same catalyst loaded with 10% or less LSM, perovskite oxides were absent, calcination temperature about 750℃ is necessary for the formation of perovskite structure in LSM/γ-Al2O3 catalysts. High activity of complete oxidation of xylen will be obtained when perovskite-type oxides.
Investigation of TPR showed that neat LSM or LSM/γ-Al2O3(20%) was reduced by H2-N2 mixed gas. Two degradation processes took place. In the first, reduced temperature peak was about 350 - 450℃. If reduction ended at 400℃, perovskite structure was retained, which may be due to the reduction of Mn3+to Mn2+ on the surface of LSM only. In the second process, perovskite structure was destroied, and La2O3, Mn2O3, Mn - Sr - O oxides could be obtained, which took place in the temperature range 685 - 750℃ and ended at 800℃. This was proved by TPR experiments (Fig. 3, 5) and XRD patterns (Fig. 4)
Catalysts LSM/γ-Al2O3(10% or 20%) heated at 500℃ have only one TPR peak, i. e. lower temperature peak. This is due to the absence of perovskite-type oxides in the catalysts. However, neat LSM or LSM/γ-Al2O3(20%) heated 750℃ or above, not only the first low temperature TPR peak but also the second peak, which is contributed by the perovskite-type oxides in these catalysts appeared. Therefore, the second TPR peak, i. e. the higher temperatue peak is a characteristic peak for perovskite-type oxides in the reduced process. When LSM/ γ-Al2O3 (10%) catalys is heated at 750℃, no perovskite-type oxides were detected by XRD, and the second reduction peak was absent also in TPR process. \
The order of the second reduction peak temperature(characteristic peak of perovskite - type ox- ides) is: neat LSM(750℃）> LSM/γ-Al2O3 20% (685-698℃) -deposited LSM/γ-Al2O3 (698℃) > LSM/γ-Al2O3 15% (677 - 680℃) >(LSM/γ-AL2O3 10% 620 - 630℃, for Mn - Al - O medium oxides on surface). It is correleted with the increasing of the effect of support sequentially.
When LSM/γ-Al2O3 catalysts were heated at 900℃, more stable phase, spinel MnAl2O4 appeared, which could be proved by TPR of model catalyst MnAl2O4/γ-Al2O3.     

低硅铝比ZSM-5分子筛上C4烃的催化裂解反应

以低硅铝比(n(SiO2)/n(Al2O3)=20-45)的ZSM-5分子筛为催化剂, 研究了混合C4烃的催化裂解反应, 并对不同硅铝比的ZSM-5分子筛进行了酸性表征. 混合C4烃的催化裂解反应结果表明, 低硅铝比的ZSM-5分子筛具有较高的低温催化活性, 高硅铝比ZSM-5分子筛催化剂上乙烯和丙烯的收率高于低硅铝比ZSM-5分子筛催化剂, 低硅铝比ZSM-5分子筛上苯和甲苯的收率高于高硅铝比ZSM-5分子筛催化剂. 在反应温度为625 ℃时, 硅铝比为20的ZSM-5分子筛催化剂上乙烯、丙烯、苯和甲苯的总收率可达79.42%. 酸性表征结果表明, 硅铝比低的ZSM-5分子筛具有更多的Bronsted(B)酸酸量、Lewis(L)酸酸量及总酸酸量, 这是低硅铝比ZSM-5分子筛具有低温高活性及高的苯和甲苯收率的原因.     

Al2O3/K2O-containing non-stoichiometric lithium disilicate-based glasses

The crystallisation kinetics of experimental glasses in 3 different systems: (A) Li₂O–SiO₂, (B) Li₂O–Al₂O₃–SiO₂ and (C) Li₂O–K₂O–Al₂O₃–SiO₂ were studied under non-isothermal conditions. The DTA results revealed a stronger tendency to crystallisation of binary compositions in comparison to the ternary and quaternary compositions comprising Al₂O₃ and K₂O which present the lower crystallisation, i.e. the crystallisation propensity follows the trend A > B > C. The devitrification process in the Li₂O–SiO₂ and Li₂O–Al₂O₃–SiO₂ systems began earlier and the rate was higher in comparison to that of glasses in the quaternary Li₂O–K₂O–Al₂O₃–SiO₂ system. Thus, addition of Al₂O₃ and K₂O to glasses of Li₂O–SiO₂ system was demonstrated to promote glass stability against crystallisation. However, the activation energy for crystallisation was shown to depend also on the SiO₂/Li₂O ratio with the binary system showing a decreasing trend with increasing SiO₂/Li₂O ratio, while the opposite tendency was being observed for compositions with added Al₂O₃ and K₂O.     

Mass transfer from theophylline hydrogels of a‐PVA/H2O and a‐PVA/NaCl/H2O system on heating

Theophylline hydrogels of atactic‐poly(vinyl alcohol) (a‐PVA)/H₂O and a‐PVA/NaCl/H₂O systems were prepared followed by cyclic freezing (?30°C for 16 hr)–thawing (at room temperature for 8 hr) and one cycle gelation (at ?20°C for 24 hr) processes, respectively. In order to prepare xerogels (dried hydrogels) of these hydogel systems, an apparently first‐order mass transfer phenomenon of water as evaporation was observed for a‐PVA/H₂O hydrogel system, while heating at 60°C. The rate of evaporation decreased with increasing time in hyperbolic fashion. The total surface area (both lateral and two end surfaces of hydrogel matrix disc) decreased linearly for the first 90 min and thereafter had a tendency towards the steady‐state. The total mass flux showed time dependent linear reduction phenomenon, which is a characteristic physical behavior for these hydrogel systems on heat treatment. When NaCl was included in a‐PVA/H₂O system mass transfer of water followed fourth‐order polynomial. But in consideration of a comparative study, sustained mass transfer was found from the hydrogel matrices of a‐PVA/H₂O/NaCl system (gelation at ?20°C). Copyright © 2003 John Wiley & Sons, Ltd.     

Layered manganese oxide with O2 structure,Li(2/3)+x(Ni1/3Mn2/3)O2 as cathode for Li-ion batteries

Using LiI as the reducing agent, the compound O2-Li_(2/3)+x(Ni_1/3Mn_2/3)O₂, x∼1/3 (O2(Li+x)) has been prepared from the O2-Li_2/3(Ni_1/3Mn_2/3)O₂ (O2(Li)). Cyclic voltammetry and voltage-capacity profiles of the O2(Li+x) phase are qualitatively different from that of O2(Li) phase. The first extraction capacity of O2(Li+x) at C/10 rate is 190 mAh/g corresponding to the removal of 2/3 mole of Li from the compound. At C/5 rate it delivers a reversible capacity of 158 mAh/g at 25 °C and 184 mAh/g at 50 °C (vs Li metal; voltage window 2.5–4.6 V). In Li-ion cells, with MCMB anode and O2(Li+x) as cathode, a discharge capacity of 140 mAh/g was obtained at C/5 rate in the voltage window 2.5–4.5 V (25 °C). The charge–discharge cycling performance and the cyclic voltammograms reveal that O2(Li) and O2(Li+x) do not convert to the spinel structure.     

Partial oscillator strengths for the photoionization of N2O and CO2 (20–60 eV)

The photoelectron branching ratios and the partial oscillator strengths (cross sections) for photoionisation of the valence orbitals of N₂O and CO₂ have been obtained in the energy range 20–60 eV using the magic angle dipole (e, 2e) method. In addition to single electron ionization processes there is a large contribution from multiple electron transitions at higher energies in agreement with recent theoretical predictions. The photoionization efficiency and the dipole oscillator strenght for total photoabsorption have also been measured.     

Theoretical study of CO adsorption on gold/alumina substrates

Aiming to understand the role of the substrate in the adsorption of carbon monoxide on gold clusters supported on metal-oxides, we have started a study of that process on two different alumina substrates: an amorphous-like fully relaxed stoichiometric (Al2O3)20 cluster and the Al terminated (0001) surface of alpha-(Al2O3) crystal. In this paper, we present first principles calculations for the adsorption of one Au atom on both alumina substrate and the adsorption of Au8 on (Al2O3)20. Then, we study the CO adsorption on the minimum energy structure of these three different gold/alumina systems. A single Au adsorbs preferably on top of an Al atom with low coordination, the binding energy being higher in the case of Au/(Al2O3)20. CO absorbs preferably on top of the Au atom, but in the case of Au/(Al2O3)20, Au forms a bridge with the Al and O substrate atoms after CO adsorption. We find other stable sites for CO adsorption on the cluster but not on the surface. This result suggests that the Au activity toward CO may be larger for the amorphous cluster than for the crystal surface substrate. For the most stable Au8/(Al2O3)20 configuration, two Au atoms bind to Al and a O atoms respectively and CO adsorbs on top of the Au which binds to the Al atom. We find other CO adsorption sites on supported Au8 which are not stable for the free Au8 cluster.     

THE QUENCHING OF TYROSINE AND TRYPTOPHAN FLUORESCENCE BY H2O AND D2O*

Abstract— The quantum yields and lifetimes of the fluorescence of tyrosine and tryptophan were determined in D₂O-H₂O and glycerol-H₂O solvent mixtures of varying composition from 10 vol.% to 100% H₂O at 15°C. Forboth amino acids the ratio of the quantum yields in D₂O and H₂O (i.e., q_D/q_H) was smaller than the ratio of the corresponding lifetimes (_D/_H). For tyrosine the ratio of the quantum yields in glycerol and H₂O (q_G/q_H) was also smaller than the corresponding _G/_H ratio, but for tryptophan q_G/g_HG/_H. The proximity of the q vs. plots for tyrosine in the two solvent mixtures indicates that at 15°C neither D₂O nor glycerol, in the pure state or when diluted with H₂O, quench tyrosine significantly. However, H₂O quenches tyrosine by a dynamic process, which increases both the radiative and the nonradiative rate constant. The quenching action is attributed to a tyrosine-H₂O exciplex, whose formation is independent of bulk viscosity and dielectric constant. Unlike tyrosine, tryptophan is quenched weakly by D₂O by a static process at 15°C (i.e., involving no change in), but H₂O quenches tryptophan much more efficiently by a dynamic process, which involves the nonradiative rate constant, but not the radiative constant. These results are explained on the basis of electrostatic complexation of the ammonium group to the carbon atom adjacent to the ring nitrogen with a lifetime which is longer thanin D₂O but shorter thanin H₂O, with solvent reorientation possibly also being an important factor in the quenching. This explanation is consistent with the fact that concentrated (8 M) urea increases q andof aqueous tryptophan ? 15–20%, while guanidine hydrochloride (6.4 M) has the opposite effect, i.e., it decreases q and t of tryptophan ? 15–20%, and with the fact that neither 8 M urea nor 6.4 M guanidine hydrochloride affects any fluorescence parameter of tyrosine at all.     

Studies on the carboxymethylation and methylation of bisphenol A with dimethyl carbonate over TiO2/SBA-15

Carboxymethylated species were selectively synthesized from dimethyl carbonate (DMC) and bisphenol A (BPA) over TiO₂/SBA-15. On the basis of catalyst characterization by means of XRD, FT-IR, HPLC and GC–MS, the relations between catalytic performance and catalyst properties were discussed. Si–O–Ti was active sites for reaction, and the interaction mode between Ti–O–Si and DMC was main factor to determine carboxymethylation and methylation. When DMC was attacked by Ti–O–Si on two oxygen atoms of CH₃–O moiety, BPA attacked carbonyl carbon to form carboxymethylated products. If the interaction occurs through the oxygen of CO moiety, BPA attacked methyl carbon to form methylated products. Chemisorbed H₂O over TiO₂/SBA-15 made DMC to act as methylating agent. After chemisorbed H₂O was removed, carboxymethylated species of two-methylcarbonate-ended-BPA (DmC(1)) and one-methylcarbonate-ended-BPA (MmC(1)) were selectively synthesized.     

复合半导体MoS_2/Cu_2O的制备及其光催化性能研究

采用两步法制备了MoS_2/Cu_2O催化剂,对其催化降解甲基橙(MO)性能进行了研究.首先,通过液相剥离和梯度离心获得少数层MoS_2纳米片,然后采用水热还原法在MoS_2纳米片上合成Cu_2O纳米颗粒,形成MoS_2/Cu_2O复合半导体,并分别通过扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)、UV-Vis紫外可见漫反射光谱(DRS)等手段对催化剂的结构进行表征.在可见光下,MoS_2/Cu_2O复合半导体降解MO的效率明显高于纯MoS_2和Cu_2O.为了获得最佳光催化活性,探究了MoS_2质量分数(5%、10%、20%、30%、40%、50%)对MoS_2/Cu_2O复合半导体光催化降解MO的影响.最后,经过5次循环实验,MoS_2/Cu_2O降解率下降为82.5%,循环稳定性有待进一步提高.     

Structural diversity controlled by alkali/alkaline earth metals for heterometallic AeI/AeII-ZnII coordination polymers based on 4-nitrobenzene-1,2-dicarboxylate

Six heterometallic Zn(II) coordination polymers, Zn(H₂O)₃(FNA) (1), [NH₄]₂[Zn(H₂O)₂(FNA)₂] (2), [ZnNa₂(FNA)₂]·3H₂O (3), [ZnK₂(FNA)₂]·H₂O (4), [ZnRb₂(FNA)₂]·2H₂O (5) and [ZnMg(FNA)₂]·4H₂O (6) (H₂FNA = 4-nitrobenzene-1,2-dicarboxylic acid), were synthesised by introducing different alkali/alkaline earth (Ae^I/Ae^II) metals. These complexes exhibit diverse structures with the different Ae^I/Ae^II metals used and distinct ligand coordination modes the ions provide. For 1 and 2, the Zn(II) centres with distorted octahedra are connected by FNA to form 1-D chain structures. The Zn(II) centres in 3–6 with distorted tetrahedra are linked by FNA to form 2-D anionic grid layers. For 3–5, these 2-D anionic grid layers are connected by alkali metal (Na, K and Rb) with the O–Ae^I–O connectivity to exhibit 3-D framework structures, while 6 features a 2-D Zn–Mg network. Luminescence properties of 1–6 have been investigated.     

在FTO导电玻璃上电化学沉积高效可见光光电化学分解水Cu2O/g-C3N4异质结膜

近几十年来,光电化学分解水制氢作为一种洁净的、能持续利用太阳能的技术受到极大关注.在众多光催化材料中,p型半导体氧化亚铜(Cu2O)被认为是最有前途的可见光光电分解水材料之一.理论上,它的光能转换为氢能的效率可达到18.7%.然而,目前所报道的Cu2O光转换效率远远低于此值;同时,纯Cu2O在光照条件下的稳定性较差.研究表明,Cu2O与其它半导体复合可以增强其光电转换效率和提高稳定性.如Cu2O和能带匹配的石墨相氮化碳(g-C3N4)复合后,光催化性能和稳定性都有较大提高.但目前所报道的Cu2O/g-C3N4复合物几乎都是粉末状催化剂,不便于回收和重复使用.本文首先采用电化学方法在FTO导电玻璃上沉积Cu2O薄膜,采用溶胶凝胶法制备g-C3N4纳米颗粒材料,然后采用电化学法在Cu2O薄膜表面沉积一层g-C3N4纳米颗粒,得到了Cu2O/g-C3N4异质结膜.分别利用X射线粉末衍射(XRD)、高分辨透射电子显微镜(HRTEM)、扫描电子显微镜(SEM)、紫外可见光谱(UV-Vis)和光电化学分解水实验分析了Cu2O/g-C3N4异质结的组成结构、表面形貌、光吸收性能及催化剂活性和稳定性.XRD和HRTEM表征显示,本文成功合成了Cu2O/g-C3N4异质结材料,SEM图表明g-C3N4纳米颗粒在Cu2O表面分布均匀,大小均一.可见光光电化学分解水结果显示,异质结薄膜的光电化学性能比纯的Cu2O和g-C3N4薄膜材料有极大提高.当在Cu2O表面沉积g-C3N4的时间为15 s时,得到样品Cu2O/g-C3N4-15异质结膜,其在–0.4 V和可见光照射条件下,光电流密度达到了–1.38 mA/cm2,分别是纯Cu2O和g-C3N4薄膜材料的19.7和6.3倍.产氢速率也达到了0.48 mL h–1 cm–2,且产氢和产氧的速率之比约为2,说明此异质结材料在可见光作用下能全分解水.经过三次循环实验,光电化学分解水的效率仅降低10.8%,表明该材料具有良好的稳定性.根据UV-Vis表征和光电化学性能对比,Cu2O/g-C3N4-15的光电性能最好,但其光吸收性能并不是最好,说明光电化学性能与光吸收不是成正比关系,主要是由于Cu2O和g-C3N4两个半导体相互起到了协同作用.机理分析表明,Cu2O/g-C3N4异质结薄膜在光照下,由于两者能带匹配,Cu2O的光生电子从其导带转移到g-C3N4的导带上,g-C3N4价带上的空隙转移到Cu2O的价带上,从而降低了光生电子和空隙的复合,提高了其光催化性能.由于g-C3N4的导带位置高于H2O(或H+)还原为H2的电势,Cu2O的价带位置低于H2O(或OH–)还原为O2的电势,所以在外加–0.4 V偏压和可见光照射条件下,Cu2O/g-C3N4能全分解水,光生载流子越多,光电化学分解水的速率越大.综上所述,在Cu2O薄膜上沉积g-C3N4后得到的异质结薄膜具有高效的光能转换为氢能性能.     

S-M（M=Al,Co）复合掺杂LiMn2O4的结构稳定性

应用量子化学电荷自洽离散变分Xα(SCC-DV-Xα)方法,研究了S-Al、S-Co复合掺杂增强尖晶石结构锂锰氧化物稳定性的作用机制.计算结果表明, S-Al复合掺杂锂锰尖晶石和S-Co复合掺杂锂锰尖晶石中的共价键强度均比未掺杂尖晶石LiMn2O4中的强,且与MnO2中的共价键强度相近; S-Al, S-Co复合掺杂尖晶石中Mn的电荷也与MnO2模型[Mn6O26]28－中十分接近. Mn原子的电荷密度次序是MnO2≈掺硫铝后锰锂尖晶石≈掺硫钴后的锂锰尖晶石< 锰锂尖晶石.即[LixMn3Co3O20S6]n－和[LixMn3Al3O20S6]n－中Mn的状态与MnO2中的Mn相似.上述结果揭示了S和非Jahn-Teller效应阳离子（Al3＋,Co3＋）复合掺杂尖晶石结构锂锰氧化物在电化学过程中不会发生Jahn-Teller畸变的内在原因.     

改性Ag/α-Al_2O_3催化丙烯气相环氧化反应

制备了以分子氧为氧化剂,对丙烯气相环氧化具有较好催化性能的改性负载银催化剂,并利用氧气程序升温脱附(O2-TPD)技术研究了氧在其表面上的脱附行为.实验结果表明:Ag/α-Al2O3催化剂只能使丙烯完全氧化成二氧化碳和水;当该催化剂用K2O改性后,可获得少量的环氧丙烷;Y2O3改性的Ag/α-Al2O3催化剂,可获得极少量的丙醛和丙酮;将0.1%(w)Y2O3添加到Ag-K2O/α-Al2O3后,可以显著提高催化剂的丙烯环氧化性能.在0.1MPa、245℃、20%C3H6/8%O2/72%N2和气体空速2000h-1的反应条件下,通过20%(w)Ag-0.1%Y2O3-0.1%K2O/α-Al2O3催化剂时,丙烯转化率为4.0%,环氧丙烷的选择性为46.8%.O2-TPD研究表明,少量的Y2O3、K2O或Y2O3-K2O作为助剂添加到20%Ag/α-Al2O3催化剂中时,减少了高温区与丙烯完全氧化有关的吸附氧物种的量,低温区余下的吸附氧物种量不变,有利于丙烯环氧化反应,提高了环氧丙烷的选择性.     

NMR study of water reorientation in molybdic acids: MoO3 · 2H2O and yellow MoO3 · H2O

Proton NMR relaxation times (T₂, T₁, T_1?) are reported for powder samples of MoO₃ · 2H₂O and yellow MoO₃ · H₂O in the temperature range 150–325 K and at 20 and 60 MHz. No translation of hydrogen atoms is detected but the spin-lattice relaxation behavior indicates reorientation of H₂O molecules. The waters coordinated to Mo atoms undergo 180° flips (about their C₂ axes) with similar motional parameters in both compounds. The interlayer waters in MoO₃ · 2H₂O undergo 180° flips with different parameters. An assumed Arrhenius-type temperature dependence of correlation times leads to preexponential factors which are “anomalously” low. The possible involvement of temperature-dependent activation barriers is discussed.