Influence of cooling rate on the liquid-phase epitaxial growth of Zn3P2

We report the liquid-phase epitaxial growth of Zn₃P₂ on InP (1 0 0) substrates by conventional horizontal sliding boat system using 100% In solvent. Different cooling rates of 0.2–1.0 °C/min have been adopted and the influence of supercooling on the properties of the grown epilayers is analyzed. The crystal structure and quality of the grown epilayers have been studied by X-ray diffraction and high-resolution X-ray rocking measurements, which revealed a good lattice matching between the epilayers and the substrate. The supercooling-induced morphologies and composition of the epilayers were studied by scanning electron microscopy and energy dispersive X-ray analysis. The growth rate has been calculated and found that there exists a linear dependence between the growth rate and the cooling rate. Hall measurements showed that the grown layers are unintentionally doped p-type with a carrier mobility as high as 450 cm²/V s and a carrier concentration of 2.81×10¹⁸ cm⁻³ for the layers grown from 6 °C supercooled melt from the cooling rate of 0.4 °C/min.     

Anisotropic vapor phase growth of Ga2O3 crystalline nanobelts

Ga₂O₃ nanobelts were synthesized by gas reaction at high temperature in the presence of oxygen in ammonia. X-ray diffraction and chemical microanalysis revealed that the nanostructures were Ga₂O₃ with the monoclinic structure. Electron microscopy study indicated the nanobelts were single crystalline with broad (0 1 0) crystallographic planes. The nanostructures grew anisotropically with the growth direction of . Statistical analysis of the anisotropic morphology of the nanobelts and electron microscopy investigation of the nanobelt tips indicated that both vapor–solid and vapor–liquid–solid mechanisms controlled the growth process. The anisotropic nature of crystallographic morphology is explained in terms of surface energy.     

Controlled synthesis of different morphologies of BaWO4 crystals via a surfactant-assisted method

BaWO₄ crystals with different morphologies, such as nanosheets, nanobelts, flower-like, quadrangled plates and sheaves of dendrite, have been successfully synthesized via PVP as templates. Our result shows that reaction parameters, such as the concentration of PVP aqueous solutions, pH value of the starting solution and molar ratio of [Ba²⁺]/[WO₄²⁻] played important roles in the formation of BaWO₄ crystal with different morphologies. It is obviously different between microwave irradiation heating and oil bath heating. The products were characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and electron diffraction.     

Phase relations around langasite (La3Ga5SiO14) in the system La2O3–Ga2O3–SiO2 in air

Phase relations around langasite (LGS, La₃Ga₅SiO₁₄) were studied on the basis of phase assemblage observed during calcination and crystallization process of samples of various compositions in the ternary system La₂O₃–Ga₂O₃–SiO₂. A ternary compound of apatite structure, La₁₄Ga_xSi_9–xO_39–x/2 was found for the first time. Crystallization of this compound was observed in the cooling process of molten samples of stoichiometric LGS as well as LGS single crystal, demonstrating that LGS is an incongruent-melting compound. A phase diagram was established primarily based on the crystallization sequence in the cooling process.     

Densities of Li2O–B2O3 melts

The densities have been systematically measured in xLi₂O–(1−x)B₂O₃ melts of different compositions with Li₂O content varying from x=0 to 0.68 from their respective melting points up to about 1450 K with a modified Archimedean method. The density decreased with increasing temperature for all the melts measured in this work. When x<0.15, the plot of temperature versus density could be well fitted by a quadratic polynomial function, and when x0.15, density decreased linearly with increasing temperature. At a fixed temperature, the density of the melts increased rapidly with Li₂O content, went through a maximum at about x=0.333 (Li₂O–2B₂O₃), and then decreased slowly as Li₂O content was further increased. In addition, the volume expansion coefficient (β) was calculated based on the densities measured in this work, and it was found that a maximum value appeared in the dependence of β on the molar ratio of Li₂O at about x=0.333.     

Hydrothermal growth of single-crystal CaV6O16·3H2O nanoribbons

CaV₆O₁₆·3H₂O nanoribbons have been prepared by the hydrothermal method in the presence of sodium dodecyl sulfate (SDS) at 160°C for 10 h. X-ray diffraction pattern indicates that the sample is monoclinic phase of CaV₆O₁₆·3H₂O with the lattice contents a=12.18 Å, b=3.598 Å, c=18.39 Å, β=118.03°. Field emission scanning electron microscopy shows that the nanoribbons have widths in the range of 150–500 nm, thicknesses of 30–60 nm and lengths of 500 mm X-ray photoelectron spectrum measurements further confirm the formation of the CaV₆O₁₆·3H₂O phase. The formation of CaV₆O₁₆·3H₂O nanoribbons is a self-assembling process, in which surfactant SDS plays the role of soft template.     

Crystallization behavior and hydrophilic performances of V2O5–TiO2 films prepared by sol–gel dip-coating

Homogeneous and transparent V₂O₅–TiO₂ composite nanometer thin films were prepared on glass substrates by sol–gel processing and dip-coating technique. The films as well as the dried powder of bulk gel were characterized by different techniques like X-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM), atomic force microscope (AFM) and thermogravimetry–differential thermal analysis (TG–DTA). The hydrophilicity of the films was determined by measuring the water contact angles on the films. The results showed that the dopant of V₂O₅ on TiO₂ thin films could produce a visible-light response to the films, and the introduction of V₂O₅ could suppress the structural phase transition and crystal growth of TiO₂ crystal. Finally, the relationship between crystalline size and hydrophilicity under sunlight was investigated in this article.     

Properties of Si-rich SiO2 films by RF magnetron sputtering

Si-rich silicon oxide (SiO_x, 1<x<2) films were prepared by RF magnetron reactive sputtering or co-sputtering on the Si(1 1 1) substrates. X-ray diffraction patterns showed that the peak of silicon nanocrystals (NCs), separated from SiO_x films, had (1 1 1) preferred orientation. The results of scanning electron microscopy indicated the Si NCs uniting into clusters. We demonstrated that the photoluminescence (PL) peaks at 650 nm was caused by defect center. In particular, we discussed the correlation between the PL and the structure of SiO_x films. The mean size of the Si NCs was estimated to be about 3 nm by the PL peak position.     

Solvothermal synthesis of K2V3O8 nanorods

A solvothermal route has been developed to synthesize K₂V₃O₈ nanorods via the reduction of V₂O₅ using ethanol as the reducing agent as well as the solvent at 200°C. X-ray diffraction and selected area electron diffraction analysis revealed that the as-synthesized products are of tetragonal structure K₂V₃O₈. Transmission electron spectroscopy image showed that the obtained K₂V₃O₈ comprises rod-like nanocrystallites. The formation mechanism of K₂V₃O₈ was studied.     

XPS and electroluminescence studies on SrS1−xSex and ZnS1−xSex thin films deposited by atomic layer deposition technique

SrS_1−xSe_x and ZnS_1−xSe_x thin films were deposited by the atomic layer deposition (ALD) technique using elemental selenium as the Se source, thus avoiding use of H₂Se or organometallic selenium compounds. X-ray diffraction (XRD) analysis showed that the films were solid solutions and X-ray photoelectron spectroscopy (XPS) data showed that the surface of both ZnS_1−xSe_x and SrS_1−xSe_x were covered with an oxide and carbon-containing contaminants from exposure to air. The oxidation of SrS_1−xSe_x extended into the film and peak shifts from sulfate were found on the surface. Luminance measurements showed that emission intensity of the ZnS_1−xSe_x:Mn alternating current thin film electroluminescent (ACTFEL) devices at fixed voltage was almost the same as that of the ZnS:Mn device, while emission intensity of the SrS_1−xSe_x:Ce devices decreased markedly as compared to the SrS:Ce device. Emission colors of the devices were altered only slightly due to selenium addition.     

Growth, dielectric, ferroelectric and optical properties of Ca0.28Ba0.72Nb2O6 single crystals

Calcium barium niobate Ca_0.28Ba_0.72Nb₂O₆ (CBN-28) crystals were grown by the Czochralski method. The effective segregation coefficients of Ca, Ba, Na elements in CBN-28 crystal growth were measured, and the rocking curve from 0 0 2 reflection of CBN-28 wafer was also measured by the high-resolution X-ray diffractometer D5005, and the full-width at half-maximum value was measured to be 70.6″. The measured dependence of dielectric constants on temperature showed the Curie temperature of the CBN-28 crystals is between 246.8 and 260 °C. Typical polarization–electric field (P–E) hysteresis loops were measured at room temperature. Ferroelectric 180° domains were observed by scanning electron microscopy (SEM) on the etched (0 0 1) surface of the CBN-28 crystals. The transmittance of [0 0 1]-oriented CBN-28 crystals was measured and the result shows that optical properties of CBN-28 crystal are almost the same as those of SBN for wavelengths between 2500 and 7500 nm.     

Synthesis of Y2O3:Eu phosphors by bicontinuous cubic phase process

A novel approach for preparation of red-emitting europium-doped yttrium oxide phosphor (Y₂O₃:Eu) by using the bicontinuous cubic phase (BCP) process was reported in this paper. The BCP system was composed of anionic surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and aqueous yttrium nitrate/europium nitrate solution. Energy dispersive spectrometer analysis revealed the homogeneous precipitation occurred in the BCP structure. Thermogravimetric analysis measurements indicated the precursor powder was europium-doped yttrium hydroxide, Y_1−xEu_x(OH)₃. Scanning electron microscopy micrographs showed the precursor powder had a primary size about 30 nm and narrow size distribution. After heat treatment in furnace above 700 °C for 4 h, high crystallinity Y₂O₃:Eu phosphors was obtained. However, the primary size of particles grew to 50–200 nm and the dense agglomerates with a size below 1 μm were formed. X-ray diffraction patterns indicated the crystal structure of precursor powders and Y₂O₃:Eu phosphors were amorphous and body-centered cubic structure, respectively. The photoluminescence analysis showed that the obtained Y₂O₃:Eu phosphor had a strong red emitting at 612 nm and the quenching started at a Eu concentration of 10 mol%. This study indicated that the BCP process could be used to prepare the highly efficient oxide-based phosphors.     

Self-catalytic branch growth of SnO2 nanowire junctions

Multiple branched SnO₂ nanowire junctions have been synthesized by thermal evaporation of SnO powder. Their nanostructures were studied by transmission electron microscopy and field emission scanning electron microcopy. It was observed that Sn nanoparticles generated from decomposition of the SnO powder acted as self-catalysts to control the SnO₂ nanojunction growth. Orthorhombic SnO₂ was found as a dominate phase in nanojunction growth instead of rutile structure. The branches and stems of nanojunctions were found to be an epitaxial growth by electron diffraction analysis and high-resolution electron microscopy observation. The growth directions of the branched SnO₂ nanojunctions were along the orthorhombic [1 1 0] and . A self-catalytic vapor–liquid–solid growth mechanism is proposed to describe the growth process of the branched SnO₂ nanowire junctions.     

Bi20TiO32 nanocones prepared from Bi–Ti–O mixture by metalorganic decomposition method

Bi₂₀TiO₃₂ in the form of nanocones are reported for the first time, which have been found during the formation of Bi₂Ti₂O₇ nanocrystals. Bi₂₀TiO₃₂ nanocones were prepared by metalorganic decomposition technique. From X-ray patterns, it was found that Bi₂₀TiO₃₂ is a metastable phase, and can transform gradually into Bi₂Ti₂O₇ phase with the annealing time increasing at a temperature of 550°C. The image of field emission scanning electron microscopy shows that the lengths of the nanocones are up to several micrometers and the diameters of cusps range from 20 to 200 nm. The studies of transmission electron microscopy show that the nanocones are crystalline Bi₂₀TiO₃₂. The growth mechanism of Bi₂₀TiO₃₂ nanocones has been proposed, which is similar to the vapor–liquid–solid growth mechanism.     

Structure and thermal stability of MOCVD ZrO2 films on Si (1 0 0)

The structure and thermal stability of ZrO₂ films grown on Si (1 0 0) substrates by metalorganic chemical vapor deposition have been studied by high-resolution transmission electron microscopy, selected area electron diffraction and X-ray energy dispersive spectroscopy. As-deposited films consist of tetragonal ZrO₂ nanocrystallites and an amorphous Zr silicate interfacial layer. After annealing at 850°C, some monoclinic phase is formed, and the grain size is increased. Annealing a 6 nm thick film at 850°C in O₂ revealed that the growth of the interfacial layer is at the expense of the ZrO₂ layer. In a 3.0 nm thick Zr silicate interfacial layer, there is a 0.9 nm Zr-free SiO₂ region right above the Si substrate. These observations suggest that oxygen reacted with the Si substrate to grow SiO₂, and SiO₂ reacted with ZrO₂ to form a Zr silicate interfacial layer during the deposition and annealing. Oxygen diffusion through the tetragonal ZrO₂ phase was found to be relatively easier than through the monoclinic phase.     

Preparation and characterization of fiber-textured SrAl2O4:Eu films grown using a homo-buffer layer

This paper describes the preparation and characterization of fiber-textured SrAl₂O₄:Eu films on a quartz glass substrate using a homo-buffer layer. The effect of the buffer layer on the crystallinity and adhesion was investigated by cross-section transmission electron microscopy and X-ray diffraction (XRD). The results show that the prepared film was not only well crystallized but also highly textured. The preferred orientation of this textured film was confirmed to be (0 3 1) by pole figure measurement. In addition, this film exhibits excellent optical transparency, with an average transmittance of more than 80% in the visible range.     

Characteristic crystal growth from amorphous WO3 film by vacuum heating

Selective growth of WO₂, W and WO_3−x crystals from amorphous WO₃ film by vacuum heating at 400–900°C was clarified. The grown WO_3−x crystals were incommensurate structure based on crystallographic share structure. The growth process of WO₂ crystal in the amorphous film was directly observed at high temperature in the electron microscope. The growth front of the WO₂ crystal consumes WO₃ microcrystallites with various orientations. The growth speed of the WO₂ depended on WO₃ microcrystallites orientation. The origin of the wavy growth front of WO₂ was due to an orientation dependence of the WO₃ microcrystallites.     

Structural and photoluminescence characteristics of molecular beam epitaxy-grown vertically aligned In0.33Ga0.67As/GaAs quantum dots

In this paper, we present the results of structural and photoluminescence (PL) studies on vertically aligned, 20-period In_0.33Ga_0.67As/GaAs quantum dot stacks, grown by molecular beam epitaxy (MBE). Two different In_0.33Ga_0.67As/GaAs quantum dot stacks were compared. In one case, the In_0.33Ga_0.67As layer thickness was chosen to be just above its transition thickness, and in the other case, the In_0.33Ga_0.67As layer thickness was chosen to be 30% larger than its transition thickness. The 2D–3D growth mode transition time was determined using reflection high-energy electron diffraction (RHEED). Structural studies were done on these samples using high-resolution X-ray diffraction (HRXRD) and cross-sectional transmission electron microscopy (XTEM). A careful analysis showed that the satellite peaks recorded in X-ray rocking curve show two types of periodicities in one sample. We attribute this additional periodicity to the presence of an aligned vertical stack of quantum dots. We also show that the additional periodicity is not significant in a sample in which the quantum dots are not prominently formed. By analyzing the X-ray rocking curve in conjunction with RHEED and PL, we have estimated the structural parameters of the quantum dot stack. These parameters agree well with those obtained from XTEM measurements.     

Facile synthesis of submicron BaTiO3 crystallites by a liquid–solid reaction method

Uniform, submicron BaTiO₃ crystallites in tetragonal structure were synthesized by a novel low-temperature liquid–solid reaction method mainly via two simple steps: firstly, BaO₂·H₂O₂ submicron particles of about 130–450 nm were precipitated from the reaction of BaCl₂ and H₂O₂ in a slightly alkaline (pH 8) aqueous solution under the ambient condition; secondly, tetragonal phase BaTiO₃ submicrocrystals with the size in the range of 180 to 400 nm could be produced by subjecting the as-prepared BaO₂·H₂O₂ and commercial TiO₂ submicron particles to thermal treatment in air at 700 °C for 10 h. The as-obtained products were characterized by X-ray powder diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and inductively coupled plasma-atomic emission spectroscopy, and scanning electron microscopy.     

The growth and spectroscopic characteristics of Ca3Y2(BO3)4:Er laser crystal

The Ca₃Y₂(BO₃)₄:Er³⁺ crystal with a size up to 20 mm×30 mm was grown by the Czochralski method. The absorption spectrum was measured and its absorption peaks were assigned to the corresponding transitions between the Er³⁺ energy levels. A broad emission spectrum from 1429.4 to 1662.8 nm was exhibited from 530 nm wavelength pumping. This crystal is promising as a tunable infrared laser crystal.