铁基磁流化床SCR烟气脱硝的磁场效应

进行了铁基磁流化床SCR烟气脱硝实验研究,并对铁基床料进行了BET和XRD分析。结果表明,在0.01～0.015 T磁场下,180℃时的SCR脱硝效率达90%,将高效脱硝温度范围从无磁场时的220～250℃扩展至180～250℃。其原因主要在于辅加磁场降低了SCR反应的表观活化能,改善了Fe_2O_3催化剂的SCR活性。磁流化床中Fe_2O_3催化剂SCR脱硝反应的磁场效应可归纳为:磁场强化NO在Fe_2O_3表面的磁化学吸附;磁场促进活性自由基NH_2的生成以及自由基NH_2与NO的反应;磁场流态化良好的传热、传质特性进一步促进了脱硝反应。     

H2O对钒钛催化剂快速SCR反应影响规律及机制研究

相比常规烟气气氛中的选择性催化剂还原脱硝(SCR)反应,商用钒钛(V₂O₅/TiO₂)催化剂在NO₂加入后构成的快速SCR反应气氛中具备优异的低温脱硝反应性能,快速SCR反应被认为具有良好的低温脱硝应用前景。烟气中存在的水蒸气会严重降低SCR催化剂在低温下的脱硝活性,因此本文重点研究了水蒸气对钒钛催化剂上标准及快速SCR反应的影响,发现快速SCR反应比标准SCR反应具备更优异的抗水性能。本文采用动力学实验结合密度泛函理论计算的研究方法,得到H₂O和NH₃在催化剂表面的竞争性吸附是H₂O抑制标准SCR反应的重要影响因素之一,而在快速SCR反应中,NO₂对催化剂的快速重氧化作用使得反应速率始终保持在较高水平,削弱了H₂O对NH₃的竞争性吸附影响,从而了展现良好的抗H₂O影响性能。     

多孔SiO2包裹磁性纳米颗粒Fe3O4的制备与表征

采用加热分解油酸铁法制备了Fe₃O₄磁性纳米颗粒,并用有机模板和反相微乳液相结合的方法将磁性纳米颗粒包裹在多孔二氧化硅中.用红外光谱(FTIR)研究了不同的处理方式对油酸铁表面官能团的影响及油酸的反应浓度和加热分解油酸铁的过程中升温速率对Fe₃O₄纳米颗粒的影响.结果表明,用乙醇和丙酮处理后的固态蜡状油酸铁表面的油酸基团会受到损害,将不利于加热分解时形成单分散性的Fe₃O₄纳 关键词： 3O₄纳米颗粒')" href="#">Fe₃O₄纳米颗粒 2包裹')" href="#">多孔SiO₂包裹 反相微乳液法 油酸铁     

Fe3O4纳米粒子对P3HT:PCBM电池的影响

为了提高太阳能电池的性能,研究磁性纳米粒子在外加磁场的作用下对聚合物太阳能电池有源层P3HT:PCBM成膜及太阳能电池性能的影响。本文采用热分解法制备了磁性Fe₃O₄纳米粒子,将不同质量分数的Fe₃O₄纳米粒子掺入到P3HT:PCBM溶液中,旋涂后在外加磁场的作用下自组成膜。通过TEM、XRD对制备的Fe₃O₄纳米粒子进行表征,并利用偏光显微镜、原子力显微镜对成膜质量进行探究。结果表明,采用热分解法制备的Fe₃O₄纳米粒子直径在10 nm左右,在外加磁场作用下,Fe₃O₄纳米粒子对成膜有一定的调控作用。当Fe₃O₄纳米粒子掺杂质量分数为1%时,太阳能电池器件的开路电压增加3.77%,短路电流增加24.93%,光电转换效率提高7.82%。     

Fe2O3上AsH3催化氧化反应机理的理论研究

本文采用密度泛函理论方法研究了Fe₂O₃上AsH₃的催化氧化反应机理.该反应以Fe₂O₃中的两个Fe原子为不同的活性中心进行研究,每个活性中心均设计了3个步骤. AsH₃分子依次与3个O₂分子在催化剂上相互作用分别形成中间体H₃AsO₂、H₃AsO₄及最终产物H₃AsO₆.研究发现,当氧化反应发生在1号铁原子(Fe1)附近,其速度控制步骤活化自由能垒为49.99 kcal/mol;当氧化反应发生在2号铁原子(Fe2)附近,其活化自由能垒为21.20 kcal/mol,与直接氧化(50.14 kcal/mol)相比大大降低.可见AsH₃在Fe₂O₃上的催化氧化反应更易发生在Fe2附近.     

MnOx/Ti-PILC低温NH3-SCR脱除NO研究

实验制备并测试MnO_x/Ti-PILCs的低温（80～260℃）SCR脱硝活性,发现当MnO_x负载量为10%,催化剂煅烧温度为300℃时催化剂表面酸性较强,活性成分分散较好,脱硝活性最佳,在180℃下,NO脱除效率接近100%。研究了氧浓度和空速等对脱硝效率的影响,发现O₂浓度为3%时,对催化剂最为有利;在65000 h^-1的高空速条件下,10 MnO_x/Ti-PILC（300）依然表现出较高活性。MnO_x/Ti-PILC与MnO_x/Al₂O₃活性相当,高于MnO_x/TiO₂。     

纳米Fe3 O4 颗粒的正电子湮没谱学研究

测量了磁性纳米Fe₃O₄颗粒的X射线衍射谱(XRD)、正电子湮没寿命谱(PALS)和符合多普勒展宽谱(CDBS),研究了不同压力和退火温度对磁性纳米Fe₃O₄颗粒物相、电子结构、缺陷及电子动量分布等的影响. XRD,PALS,CDBS测量结果表明:纳米Fe₃O₄颗粒的缺陷浓度随压力的增加而增大,但物相和缺陷类型并未发生变化;磁性纳米Fe₃O_{4< 关键词： 正电子 3}O₄')" href="#">Fe₃O₄ 寿命谱 多普勒展宽谱     

磁场对液态铝和固态铁界面微观组织的影响

研究了直流磁场、交流磁场对液态铝和固态铁界面微观组织的影响，采用金相显微镜、电子探针和x射线衍射等方法对其扩散层内生成物进行了分析.结果表明，在直流磁场和交流磁场作用下，固态铁界面内形成的扩散层厚度均比无磁场时小；在交流磁场作用下，液态铝和固态铁的界面变得凹凸不平；在垂直于磁场方向上，直流磁场抑制了铝原子和铁原子之间的扩散，交流磁场则促进了扩散；无磁场时固态铁内扩散层中生成的金属间化合物由FeAl₃和Fe₂Al₅组成，直流磁场条件下只有Fe₂Al_{5生成，交流磁场作用下由Fe2Al5和Fe4Al13组成. 关键词： 磁场 铝 铁 金属间化合物 扩散}     

纳米La2(MoO4)3∶Eu/Fe3O4磁性荧光粉末的制备及用于指纹显现的研究

采用水热法和共沉淀法分别合成了纳米La₂(MoO₄)₃∶Eu荧光材料和纳米Fe₃O₄磁性材料,并利用透射电子显微镜、X射线衍射仪、荧光光谱仪表征纳米材料的形貌尺寸、晶体结构、荧光性能。经表征,纳米La₂(MoO₄)₃∶Eu荧光材料的微观形貌为片状结构,晶体结构为四方晶型,其发射光谱中出现了Eu3+的特征发射峰;纳米Fe₃O₄磁性材料的微观形貌为球形颗粒,晶体结构为立方晶型,并具有超顺磁性。然后,将以上两种纳米材料以一定比例混合均匀,制备了具有超顺磁性的La₂(MoO₄)₃∶Eu/Fe₃O₄纳米荧光粉末。经表征,该磁性纳米荧光粉末的微观形貌为片状结构与球形颗粒的混合,其发射峰位置未发生变化,而发光强度有所降低,但仍能够满足指纹显现的需要。最后,将制备的纳米磁性荧光粉末用于显现不同类型客体表面的潜在指纹。显现效果表明,对于光滑客体表面的指纹,使用磁性纳米荧光粉末与纳米荧光粉末的显现效果无明显差异;对于粗糙客体表面的指纹,使用磁性纳米荧光粉末能够清晰显现出指纹的细节特征,其显现效果明显优于普通纳米荧光粉末,并能够有效避免粉末扬尘现象。本研究制备的纳米磁性荧光粉末是一种理想的指纹显现材料,其指纹显现具有背景干扰低、显现效果好、适用范围广、无粉末扬尘等优点,在刑事案件现场具有广阔的应用前景。     

界面活性剂对Fe3O4磁性与穆斯堡尔谱的影响

测量了不同颗粒尺寸Fe₃O₄覆盖界面活性剂前后磁性、红外谱以及穆斯堡尔谱。实验结果表明界面活性剂与Fe₃O₄微粒表面为化学吸附,覆盖界面活性剂后在相同磁场下磁化强度有所下降,穆斯堡尔谱变得弥散,随着颗粒尺寸变小,穆斯堡尔谱内场减小,谱线变得更为弥散,实验结果可以用表面各向异性的理论进行解释。 关键词：     

以理论为先导以实践促提高

探讨在现行电子类实验教学大纲下的验证性实验如何与实际电子制作相结合，使学生由被动实验转为主动实验。通过制作发现问题、分析问题并解决问题，进一步巩固和加深对相关理论的理解，培养学生的实践能力。     

Motion by curvature by scaling nonlocal evolution equations

We prove convergence to a motion by mean curvature by scaling diffusively a nonlinear, nonlocal evolution equation. This equation was introduced earlier to describe the macroscopic behavior of a ferromagnetic spin system with Kac interaction which evolves with Glauber dynamics. The convergence is proven in any time interval in which the limiting motion is regular.     

Cooling by heating: refrigeration powered by photons

We propose a new mechanism for refrigeration powered by photons. We identify the strong coupling regime for which maximum efficiency is achieved. In this case, the cooling flux is proportional to T in the low temperature limit T→0.     

Thrombocytogenesis by megakaryocyte; Interpretation by protoplatelet hypothesis

Serial transmission electron microscopy of human megakaryocytes (MKs) revealed their polyploidization and gradual maturation through consecutive transition in characteristics of various organelles and others. At the beginning of differentiation, MK with ploidy 32N, e.g., has 16 centrosomes in the cell center surrounded by 32N nucleus. Each bundle of microtubules (MTs) emanated from the respective centrosome supports and organizes 16 equally volumed cytoplasmic compartments which together compose one single 32N MK. During the differentiation, single centriole separated from the centriole pair, i.e., centrosome, migrates to the most periphery of the cell through MT bundle, corresponding to a half of the interphase array originated from one centrosome, supporting one "putative cytoplasmic compartment" (PCC). Platelet demarcation membrane (DM) is constructed on the boundary surface between neighbouring PCCs. Matured PCC, composing of a tandem array of platelet territories covered by a sheet of DM is designated as protoplatelet. Eventually, the rupture of MK results in release of platelets from protoplatelets. (Communicated by Tadamitsu Kishimoto, M.J.A.).     

Gravitational Lensing by Traversable Wormholes Supported by Three-Form Fields

In this paper, the deflection angle of light by traversable wormholes, which are supported by the three-form fields, are studied. The specific forms of the redshift and shape functions that produce results compatible with the energy conditions at throat of the wormholes are used. Having used the well-defined parameter sets of the three-form wormholes, the photon geodesic motion is investigated under the effective potential of the wormhole background. As a result, it is discovered that the radius of the photon sphere can be used to analyze the geometrical structures of a physical wormhole. The analytical form of the effective potential is used to figure out a deflection angle of light caused by wormholes with the three-from fields. In this work, the relativistic images generated from the wormholes are also constructed.     

Te-waves guided by arbitrary nonlinear dielectrics bounded by linear media

Considerable interest is currently being devoted to nonlinear propagation in dielectric slab waveguides for integrated optics and millimetric applications. Much of the current work is based on Kerr-like ( E ²) nonlinear media and numerically discussed. We present a exact solution of TE-waves for arbitrary nonlinear dielectric ( |E| ). We applicate this solution to the planar nonlinear optic waveguides and the dispersion relations are given. The results show that the propagation constants are a function of the field magnitude.Supported by deutscher akademischer austauschdienst (DAAD)He is now with Dept. Electrical Engineering, Duisburg University, 4100 Duisburg, Germany     

Dephasing by extremely dilute magnetic impurities revealed by Aharonov-Bohm oscillations

We have probed the magnetic field dependence of the electron phase coherence time tau(phi) by measuring the Aharonov-Bohm conductance oscillations of mesoscopic Cu rings. Whereas tau(phi) determined from the low-field magnetoresistance saturates below 1 K, the amplitude of Aharonov-Bohm h/e oscillations increases strongly on a magnetic field scale proportional to the temperature. This provides strong evidence that a likely explanation for the frequently observed saturation of tau(phi) at low temperature in weakly disordered metallic thin films is the presence of extremely dilute magnetic impurities.     

Laser-induced nano-patterning by means of interference subpatterns generated by microspheres

Interference patterns generated by a regular lattice of SiO₂ microspheres on a transparent support are used for the surface patterning of polyimide (PI) foils. Using 248 nm excimer-laser radiation, thousands to millions of holes with a full width at half maximum (FWHM) of 160±40 nm can be generated with a single laser pulse. Received: 1 March 2002 / Accepted: 4 March 2002 / Published online: 10 September 2002 RID="*" ID="*"Corresponding author. Fax: +43-732/2468-9242, E-mail: dieter.baeuerle@jku.at     

强流脉冲电子束应力诱发的微观结构

利用强流脉冲电子束装置在各种工艺条件下对奥氏体不锈钢、单晶铝及多晶铝等面心立方金属进行辐照处理.利用扫描电子显微镜和透射电子显微镜等详细分析了辐照样品的变形组织与结构.通过分析，在一定程度上建立起强流脉冲电子束诱发的应力特征与变形结构之间的关系，并对目前现有的几种应力波数值模拟结果进行了分析.实验结果表明，强流脉冲电子束能够在材料内部诱发10²—10³MPa的应力，其传播方式与材料的 晶体结构关系密切.这一应力是导致材料深层性能与微观组织结构发生变化的根源所在. 关键词： 强流脉冲电子束 应力 微观结构 变形