Determination of steryl sulphates in invertebrate tissue by liquid chromatography–tandem mass spectrometry

A method for the identification and quantification of underivatised steryl sulphates in invertebrates by liquid chromatography (LC) coupled with tandem mass spectrometry (MS) involving a single cleanup step has been developed. Negative electrospray ionisation and positive and negative atmospheric-pressure chemical ionisation (APCI) spectra of steryl sulphate showed pseudomolecular ions ([M+H–H₂SO₄]⁺or [M–H]⁻). Collision-induced dissociation (CID) was efficient only in positive APCI. LC-MS in negative APCI was least susceptible to interference and possible differences in response factors. The detection limits (signal-to-noise ratio of 3) based on cholest-5-enyl-3-sulphate in positive and negative APCI modes are 3.66 and 0.73 pmol μL⁻¹, respectively. Calibration plots and response factors for cholest-5-enyl-3-sulphate relative to the internal standard, cholecalciferyl-3-sulphate, in both positive and negative polarities, were linear in the concentration range from 1.22 to 16.4 pmol μL⁻¹ with good coefficients of determination (R ²>0.98). It is suggested that the structure elucidation of steryl sulphates is best achieved in CID positive APCI mode, whereas their quantification should be carried out using negative APCI.     

Effect of eluent on the ionization process in liquid chromatography-mass spectrometry

The most widely used ionization techniques in liquid chromatography-mass spectrometry (LC-MS) are electrospray ionization (ESI), atmospheric pressure chemical ionization (APCI) and atmospheric pressure photoionization (APPI). All three provide user friendly coupling of LC to MS. Achieving optimal LC-MS conditions is not always easy, however, owing to the complexity of ionization processes and the many parameters affecting mass spectrometric sensitivity and chromatographic performance. The selection of eluent composition requires particular attention since a solvent that is optimal for analyte ionization often does not provide acceptable retention and resolution in LC. Compromises must then be made between ionization and chromatographic separation efficiencies. The review presents an overview of studies concerning the effect of eluent composition on the ionization efficiency of ESI, APCI and APPI in LC-MS. Solvent characteristics are discussed in the light of ionization theories, and selected analytical applications are described. The aim is to provide practical background information for the development and optimization of LC-MS methods.     

Analysis of urinary nucleosides. I. Optimisation of high performance liquid chromatography/electrospray mass spectrometry

In order to optimise the analysis of urinary nucleosides by high performance liquid chromatography/mass spectrometry (HPLC/MS), the HPLC separation of these compounds was performed at different 'flow rates' and 0.2mL/min was found to give both a better separation and ionisation. The ionisation conditions were optimised to give the best intensity of the molecules quasi-molecular ions. The ion distribution profile and ionisation in both positive and negative mode were examined and the detection of the protonated molecule in positive mode chosen for further analysis. The limits of detection of the method developed are reported and representative LC/MS and LC/MS/MS spectra shown. Typical urinary nucleoside chromatograms are presented.     

Determination of fluoroquinolones in chicken tissues by LC-coupled electrospray ionisation and atmospheric pressure chemical ionisation

The aim of this work was to develop a method for determining seven quinolones (ciprofloxacin, danofloxacin, enrofloxacin, sarafloxacin, difloxacin, oxolinic acid and flumequine) in chicken muscle by LC coupled to MS. Two ionisation techniques, ESI and atmospheric pressure chemical ionisation (APCI) were compared using standard solutions. LOD and LOQwere determined under the optimised conditions for the two sources. The ESI was found the best for the purpose. The optimised method (LC-ESI-MS) was validated for the simultaneous analysis of the quinolones regulated by European Community in spiked chicken tissues, using norfloxacin as internal standard. Recoveries obtained varied in the range 60-109%. This method was compared with LC-UV method established previously.     

The application of gas chromatography/atmospheric pressure chemical ionisation time‐of‐flight mass spectrometry to impurity identification in Pharmaceutical Development

Accurate mass measurement (used to determine elemental formulae) is an essential tool for impurity identification in pharmaceutical development for process understanding. Accurate mass liquid chromatography/mass spectrometry (LC/MS) is used widely for these types of analyses; however, there are still many occasions when gas chromatography (GC)/MS is the appropriate technique. Therefore, the provision of robust technology to provide accurate mass GC/MS (and GC/MS/MS) for this type of activity is essential. In this report we describe the optimisation and application of a newly available atmospheric pressure chemical ionisation (APCI) interface to couple GC to time‐of‐flight (TOF) MS. To fully test the potential of the new interface the APCI source conditions were optimised, using a number of standard compounds, with a variety of structures, as used in synthesis at AstraZeneca. These compounds were subsequently analysed by GC/APCI‐TOF MS. This study was carried out to evaluate the range of compounds that are amenable to analysis using this technique. The range of compounds that can be detected and characterised using the technique was found to be extremely broad and include apolar hydrocarbons such as toluene. Both protonated molecules ([M + H]⁺) and radical cations (M^+.) were observed in the mass spectra produced by APCI, along with additional ion signals such as [M + H + O]⁺. The technique has been successfully applied to the identification of impurities in reaction mixtures from organic synthesis in process development. A typical mass accuracy of 1–2 mm/zunits (m/z 80–500) was achieved allowing the reaction impurities to be identified based on their elemental formulae. These results clearly demonstrate the potential of the technique as a tool for problem solving and process understanding in pharmaceutical development. The reaction mixtures were also analysed by GC/electron ionisation (EI)‐MS and GC/chemical ionisation (CI)‐MS to understand the capability of GC/APCI‐MS relative to these two firmly established techniques. Copyright © 2010 John Wiley & Sons, Ltd.     

基于超高效液相色谱-八端口转子阀的微升级预分级系统的建立

复杂生物系统蛋白质组的深度覆盖鉴定得益于近年来快速发展的高效色谱分离和串联质谱分析技术。二维高效液相色谱（2-D HPLC）是实现复杂肽混合物正交分离的有效手段，但其缺点是运行时间长，通常要求肽上样量在毫克级别，且收集时的组分体积大，后续合并流程复杂，而有望替代其的StageTip技术，则由于有限的色谱分离梯度，难以达到充分的正交分离。该文探索了超高效液相色谱（UPLC）和八端口转子阀联用，作为高效、便捷肽段预分离和收集系统的可行性。研究结果显示，将UPLC的高pH反相色谱分馏与在线LC-MS/MS相结合，可以实现高pH和低pH条件下基于肽段不同色谱保留行为的正交互补分离，在蛋白质鉴定方面表现出优越的性能。应用该方法对人肝癌细胞系HepG2进行3次技术重复试验，重复试验间具有非常高的定量重现性（决定系数R²>0.95）。与传统StageTip方法相比，肽段鉴定数提高了23.52%。该分级方法灵活、稳定，能够针对较少的样品开展蛋白质组深度覆盖分析。     

Liquid chromatography with atmospheric pressure chemical ionization and electrospray ionization mass spectrometry of flavonoids with triple-quadrupole and ion-trap instruments

With 15 flavonoids as test compounds, the analytical performance of four modes of LC-MS, multiple MS (MSn) and tandem MS operation (atmospheric pressure chemical ionization (APCI), electrospray ionization, positive and negative ionization) was compared for two mass spectrometers, a triple-quadrupole and an ion-trap instrument. Two organic modifiers, methanol and acetonitrile, and two buffers, ammonium acetate and ammonium formate, were used. In general, the use of APCI in the negative ion mode gave the best response, with the signal intensities and the mass-spectral characteristics not differing significantly between the two instruments. The best results were obtained when methanol-ammonium formate (pH 4.0) was used as LC eluent. Under optimum conditions full-scan limits of detection of 0.1-30 mg/l were achieved in the negative APCI mode. Here it needs to be emphasized that up to 2-order response differences were found both between analytes and between modes of ionization. This implies that one should be very cautious when interpreting data on the screening of real-life samples. The main fragmentations observed in the MSn spectra on the ion-trap, or the tandem MS spectra on the triple-quadrupole were generally the same. The advantage of the former approach is the added possibility to ascertain precursor-->product ion relationships.     

Analysis of iso-alpha-acids and reduced iso-alpha-acids in beer by direct injection and liquid chromatography with ultraviolet absorbance detection or with mass spectrometry

A liquid chromatography (LC) method is described for the simultaneous analysis of iso-alpha-acids and reduced iso-alpha-acids in beer. Volatile mobile phase additives were selected to enable hyphenation to mass spectrometric (MS) operated in the atmospheric pressure chemical ionization (APCI) mode. Contrary to other recent LC optimization procedures for the same compounds, an alkaline pH was selected hereby improving peak shape and selectivity. Both UV and MS detection are sensitive enough to analyze beers without sample pre-concentration. All major bitter acids are separated within 65 min with exception of cis-dihydroisoadhumulone, which co-elutes with trans-isocohumulone. Due to the selectivity of the MS, these compounds could be differentiated according to their m/z value. The performance in terms of quantification of bitter acids by LC-UV and LC-MS are compared for standard solutions and a selection of 14 beers.     

Ionisation in the absence of high voltage using supercritical fluid chromatography: a possible route to increased signal

Supercritical fluid chromatography (SFC) is fast becoming a technique of choice for the analysis of a wide range of compounds and has been found to be complementary to high-performance liquid chromatography (HPLC). The combination of SFC and mass spectrometry (MS) affords a very useful tool in the separation and analysis of compounds. In this study the ionisation of samples in the absence of an applied electrospray voltage has been observed when using SFC/MS, with some compounds showing increased sensitivity when all ionisation source high voltage (HV) is removed. In an attempt to understand the mechanism of ionisation, a series of test compounds were analysed using standard electrospray ionisation (ESI) and atmospheric pressure chemical ionisation (APCI) source configurations and also different API source designs. In both cases, data were acquired with the applied high voltage on (normal conditions) or with the high voltage off, i.e. no voltage spray (novo-spray). The standards were analysed with a range of pressure and modifier percentage conditions. To understand the nature of the ionisation process observed, this was compared with three established liquid-to-gas ionisation mechanisms. These were thermospray (TSP), charge residue model (CRM) of ESI and sonic spray ionisation (SSI). Experiments were undertaken in an attempt to explain this ionisation phenomenon and quantify any observed change in sensitivity. The most important point to note is that enhanced ionisation was observed under novo-spray conditions in a SFC/MS configuration, which in certain cases provides a lowering in the overall limit of detection (LOD).     

Analysis of anthraquinones in Rubia tinctorum L. by liquid chromatography coupled with diode-array UV and mass spectrometric detection

A liquid chromatographic (LC) method for the separation of both anthraquinone glycosides and aglycones in extracts of Rubia tinctorum was improved. For on-line MS detection atmospheric pressure chemical ionisation as well as electrospray ionisation (ESI) were used. The glycosides were ionised in both positive and negative ionisation (NI) mode, the aglycones only in the NI mode. With ESI ammonia was added to the eluent post-column to deprotonate the compounds. The efficiency of mass detection of the hydroxyanthraquinone aglycones was found to depend on the pKa value of the component. LC-diode-array detection and LC-MS provide useful complementary information for the identification of anthraquinones in plant extracts, which was proven with the identification of munjistin and pseudopurpurin.     

Normal-phase high-performance liquid chromatographic separations using ethoxynonafluorobutane as hexane alternative. II. Liquid chromatography-atmospheric pressure chemical ionization-mass spectrometry applications with methanol gradients

We have reported recently that high-speed normal-phase (NP) HPLC separations of a broad range of organic compounds can be performed on cyano columns using gradients of methanol in hexane-like solvent-ethoxynonafluorobutane (ENFB), available commercially. In this communication, we demonstrate that atmospheric pressure chemical ionization (APCI) in combination with mass spectrometry (MS) can be effectively used for detection in such separations. The efficiency of APCI under conditions studied has also been compared to the efficiency of traditional electrospray ionization (ESI) in combination with MS for reversed-phase (RP) HPLC of the same compounds. The compounds included in this study were steroids, benzodiazepines, and other central nervous system-active substances, nonsteroidal anti-inflammatory drugs, tricyclic antidepressants, and beta-adrenergic blocking agents. Non-polar compounds were found to respond stronger when APCI-MS technique was used, whereas APCI and ESI ionization efficiencies were comparable when polar substances were studied. The combination of normal-phase HPLC separation conditions with mass spectral detection may expand the range of LC-MS applications traditionally associated with reversed-phase HPLC and ESI-MS detection.     

Liquid chromatography-tandem mass spectrometry for the identification of impurities in d-allethrin samples

A previous GC/MS study highlighting the impurity profile of the synthetic pesticide d-allethrin is extended here to validate and confirm the impurities identity through the development of soft ionisation HPLC-MS methods. To accomplish this, we developed a reverse phase LC-MS analysis in gradient elution with two distinct soft ionisation techniques, the atmospheric pressure ionisation with electrospray source (API-ESI) and the chemical ionisation (APCI). A single quadrupole and an ion trap, which allowed the simultaneous determination of the molecular masses and structural information of the impurities by acquisition of collisionally induced (CID) product ions spectrum and in-source fragmentation, were employed as analysers. Single quadrupole and ion trap analysers resulted perfectly matching in the d-allethrin impurity fragmentation patterns. All the main impurities over 0.1% identified by GC/MS were confirmed. Results indicate that the proposed HPLC/MS method was found appropriate to confirm the presence of impurities such as chrysolactone, chloro allethrin derivatives, allethrolone and chrysanthemic acid, excluding their formation under GC/MS strong ionisation condition.     

Capillary liquid chromatography-microchip atmospheric pressure chemical ionization-mass spectrometry

A miniaturized nebulizer chip for capillary liquid chromatography-atmospheric pressure chemical ionization-mass spectrometry (capillary LC-microchip APCI-MS) is presented. The APCI chip consists of two wafers, a silicon wafer and a Pyrex glass wafer. The silicon wafer has a DRIE etched through-wafer nebulizer gas inlet, an edge capillary insertion channel, a stopper, a vaporizer channel and a nozzle. The platinum heater electrode and pads for electrical connection were patterned on to the Pyrex glass wafer. The two wafers were joined by anodic bonding, creating a microchip version of an APCI-source. The sample inlet capillary from an LC column is directly connected to the vaporizer channel of the APCI chip. The etched nozzle in the microchip forms a narrow sample plume, which is ionized by an external corona needle, and the formed ions are analyzed by a mass spectrometer. The nebulizer chip enables for the first time the use of low flow rate separation techniques with APCI-MS. The performance of capillary LC-microchip APCI-MS was tested with selected neurosteroids. The capillary LC-microchip APCI-MS provides quantitative repeatability and good linearity. The limits of detection (LOD) with a signal-to-noise ratio (S/N) of 3 in MS/MS mode for the selected neurosteroids were 20-1000 fmol (10-500 nmol l(-1)). LODs (S/N = 3) with commercial macro APCI with the same compounds using the same MS were about 10 times higher. Fast heat transfer allows the use of the optimized temperature for each compound during an LC run. The microchip APCI-source provides a convenient and easy method to combine capillary LC to any API-MS equipped with an APCI source. The advantages and potentials of the microchip APCI also make it a very attractive interface in microfluidic APCI-MS.     

Determination of cholesterol oxides in processed food using high-performance liquid chromatography-mass spectrometry with atmospheric pressure chemical ionisation

The present work describes the development and application of an on-line atmospheric pressure ionisation (APCI) LC-MS interface for the simultaneous determination of seven toxicologically relevant cholesterol oxides (7alpha-hydroxycholesterol, 7beta-hydroxycholesterol, 25-hydroxycholesterol, 7-ketocholesterol, 5,6alpha-, 5,6beta-epoxycholesterol and cholestan-3beta,5alpha,6beta-triol). The HPLC method has been optimised to reach better separation of all tested compounds. The influences of APCI parameters (nebulising temperature, cone voltage, source temperature) on signal intensity and fragmentation pattern were investigated for all tested cholesterol oxides compounds. This is the first report on optimisation and determination of two compounds 7alpha-hydroxycholesterol and 5,6beta-epoxycholesterol in processed food using LC-MS. After extraction with hexane, clean-up was carried out using solid-phase extraction on a silica column. For the chromatographic separation of cholesterol oxides an Aquasil C18 column was used with acetonitrile-methanol (60:40) as mobile phase. For the first time we report the use of such a C18 column with a relatively hydrophilic nature for the separation of cholesterol oxides. APCI-MS detection was then applied in selected ion monitoring and positive ion modes by using the molecular ions and the main fragments. The developed method shows good linearity, high repeatability and good recovery for all tested cholesterol oxides. The method was applied for determination of seven selected cholesterol oxidation products in different foodstuffs such as butter, butteroil, lard and egg powder.     

Liquid chromatography multi-stage mass spectrometry for the analysis of 5-hydroxymethylfurfural in foods

A new, simple and selective method for the analysis of 5-hydroxymethylfurfural (HMF) in foods by liquid chromatography coupled to ion trap multi-stage mass spectrometry (LC-MS(n)) is proposed in the present study. Several chromatographic columns were tested and the best results were obtained using a phenyl fluorinated column. MS conditions were established using an atmospheric pressure chemical ionisation (APCI) source in the positive ionisation mode. MS/MS was used for quantitative analysis while MS(3) was required for confirmation purposes. Quality parameters such as day-to-day and run-to-run precision (RSD<10%) and detection limit (133 ng g(-1), 333 pg injected) were established. This method was successfully applied to the analysis of HMF content in several Spanish food samples from a local market.     

Fast liquid chromatography/tandem mass spectrometry (highly selective selected reaction monitoring) for the determination of toltrazuril and its metabolites in food

In this work a fast liquid chromatography (LC)–tandem mass spectrometry (MS/MS) method was developed for the analysis of toltrazuril, a coccidiostatic drug, and its metabolites in meat food products. The applicability of atmospheric pressure chemical ionization (APCI) and heated electrospray ionization in both positive and negative modes was studied. APCI in negative mode provided the best results and the base peak originated from the loss of CF₃ (toltrazuril and toltrazuril sulfone) and CHF₃• (toltrazuril sulfoxide) was used as the precursor ion in MS/MS. A fast LC separation on a C₁₈ Fused-Core™ column was used together with the APCI-MS/MS method developed using enhanced mass resolution mode (highly selective selected reaction monitoring, H-SRM) to improve the sensitivity and selectivity for the analysis of these compounds in food samples. A simple sample treatment based on an extraction with acetonitrile and a cleanup with a C₁₈ cartridge was used. The LC-MS/MS (H-SRM) method showed good precision (relative standard deviation lower than 10%), accuracy, and linearity and allowed the determination of these compounds in food samples down to the parts per billion level (limits of detection between 0.5 and 5 μg kg^-1).     

UPLC-MS/MS screening method for simultaneous identification and characterisation of acidic and basic pharmaceuticals

ABSTRACT

A new screening method was developed for the simultaneous determination of seven acidic and basic pharmaceuticals by the ultra-high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) utilising triple quadrupole mass spectrometry as a detector. The target pharmaceutical compounds of interest in this work belong to different classes of pharmaceutical group with different physico-chemical properties. Both the positive and negative ionisation modes (dual ionisation mode) in electrospray ionisation (ESI) were used simultaneously. Unlike previous studies, the performance of the dual ionisation mode was compared with the positive and negative ionisation modes individually in terms of analysis time and sensitivity. Results indicate that the developed screening method was successfully applied for the simultaneous determination of the acidic and basic pharmaceutical compounds. Using dual ionisation mode reduced the analyses time while still maintaining sensitivity and quality of the analytical result. The new method was implemented in detecting the targeted analyte in a real sample of wastewater. The instrument detection limit (IDL) was as low as 9.7 fg, indicating a high sensitivity as compared to the corresponding methods. The precision of the instrument was calculated as the relative standard deviation (RSD) ranging from 1.4 to 11.0%. The limit of quantification (LOQ) for the method was over the range 0.77–177 ng L^?1 and 1.05–100 ng L^?1 for the influent and effluent wastewater, respectively.     

LC-electron capture APCI-MS for the determination of nitroaromatic compounds

The determination of selected nitroaromatic compounds in liquid chromatography-mass spectrometry with electron capture (EC) ionisation using a commercial atmospheric pressure chemical ionisation (APCI) interface in the negative mode is described. The electron capture effect is observed for nitroaromatics which do not easily undergo deprotonation under these conditions. Depending on the structure of the analytes, either dissociative or, for the first time in LC-MS, non-dissociative electron capture is observed. Limits of detection and linear range for the determination of the analytes match those obtained for nitroaromatics which undergo deprotonation. The investigated substances comprise numerous substituted nitrobenzenes and nitrobenzooxadiazoles.     

Liquid chromatography/negative ion atmospheric pressure photoionization mass spectrometry: a highly sensitive method for the analysis of organic explosives

Gas chromatography/mass spectrometry (GC/MS) is applied to the analysis of volatile and thermally stable compounds, while liquid chromatography/atmospheric pressure chemical ionization mass spectrometry (LC/APCI‐MS) and liquid chromatography/electrospray ionization mass spectrometry (LC/ESI‐MS) are preferred for the analysis of compounds with solution acid‐base chemistry. Because organic explosives are compounds with low polarity and some of them are thermally labile, they have not been very well analyzed by GC/MS, LC/APCI‐MS and LC/ESI‐MS. Herein, we demonstrate liquid chromatography/negative ion atmospheric pressure photoionization mass spectrometry (LC/NI‐APPI‐MS) as a novel and highly sensitive method for their analysis. Using LC/NI‐APPI‐MS, limits of quantification (LOQs) of nitroaromatics and nitramines down to the middle pg range have been achieved in full MS scan mode, which are approximately one order to two orders magnitude lower than those previously reported using GC/MS or LC/APCI‐MS. The calibration dynamic ranges achieved by LC/NI‐APPI‐MS are also wider than those using GC/MS and LC/APCI‐MS. The reproducibility of LC/NI‐APPI‐MS is also very reliable, with the intraday and interday variabilities by coefficient of variation (CV) of 0.2–3.4% and 0.6–1.9% for 2,4,6‐trinitrotoluene (2,4,6‐TNT). Copyright © 2008 John Wiley & Sons, Ltd.     

Ultra high performance supercritical fluid chromatography coupled with tandem mass spectrometry for screening of doping agents. I: Investigation of mobile phase and MS conditions

The conditions for the analysis of selected doping substances by UHPSFC–MS/MS were optimized to ensure suitable peak shapes and maximized MS responses. A representative mixture of 31 acidic and basic doping agents was analyzed, in both ESI+ and ESI− modes. The best compromise for all compounds in terms of MS sensitivity and chromatographic performance was obtained when adding 2% water and 10 mM ammonium formate in the CO₂/MeOH mobile phase. Beside mobile phase, the nature of the make-up solvent added for interfacing UHPSFC with MS was also evaluated. Ethanol was found to be the best candidate as it was able to compensate for the negative effect of 2% water addition in ESI− mode and provided a suitable MS response for all doping agents.