Structural characterization of the sol–gel oxide powders from the ZnO–TiO2–SiO2 system

This work is a study that deals with the synthesis by the sol–gel method and the structural characterization of the oxide powders belonging to the ternary system ZnO–TiO₂–SiO₂ (ZTS). The sol–gel synthesis starts from inorganic precursors, which have been processed under the variation of different technological parameters. We have investigated the dependence of the gelling time on pH and on the temperature of synthesis as well as on water and ammonia amounts. In the case of ZTS samples, the shortest gelling duration appears for low pH values when ZnO content is increased and at small ammonia concentrations when the ZnO content is decreased, respectively. On the contrary, ZTS samples containing high amounts of TiO₂ provide evidence of a short gelling time for high pH and large ammonia amounts. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy provided structural information on these ternary oxide powders. These analyses revealed that relative high amounts of ZnO yields in a change from octahedral [ ZnO₆] units to tetrahedral [ ZnO₄] units in the powder structure. Optical phonons specific for SiO₂ and TiO₂ in both octahedral and tetrahedral groups are shown. High thermal and chemical stability was put in evidence by differential thermal analysis (DTA) and thermo-gravimetric analysis (TGA) in the 20–1000 C temperature range.     

Synthesis and high-frequency magnetic properties of sol–gel derived Ni–Zn ferrite–forsterite composites

Ni_0.5Zn_0.5Fe₂O₄–forsterite composites were synthesized by a sol–gel method. X-ray diffraction and SEM were used to characterize the crystallization behavior of the composite samples which were heat treated at temperatures varying from 800 to 1100°C. The results showed that Ni_0.5Zn_0.5Fe₂O₄ and forsterite (Mg₂SiO₄) can co-crystallize and the crystallites grow even more larger with increasing heat-treatment temperature. High-frequency (10 MHz–1 GHz) magnetic and dielectric properties of the composite samples were presented. Permeability increased with heat-treatment temperature. Quality factor was found to be two orders higher than that of equivalent pure, bulk ferrite.     

Synthesis, characterization and magnetic properties on nanocrystalline BaFe12O19 ferrite

Single phase BaM (BaFe₁₂O₁₉) ferrites are prepared by using sol–gel method. The preparing conditions of samples are investigated in detail, such as acid/nitrate ratio, the value of pH and annealing temperature. The best conditions on preparing BaFe₁₂O₁₉, which can be obtained on a Fe/Ba ratio of 12, the citric acid contents R = 3, the starting pH of solution is 9, and annealing temperature 950 °C. The thermal decomposition behavior of the dried gel was examined by TG–DSC, the structure and properties of powders were measured respectively by XRD techniques. The magnetic properties of barium ferrites are emphatically researched about the changing crystallite size and annealing temperature by the vibrating sample magnetometer (VSM). Magnetic measurement shows that the barium ferrite samples annealed at 1000 °C has the maximal coercive field of 5691.91 Oe corresponding to the maximal remnant magnetization of 35.60 emu/g and the sample synthesized at 1000 °C has the maximal saturation magnetization of 60.75 emu/g.     

Effect of C doping on the structural and optical properties of sol–gel TiO2 thin films

Undoped and C-doped TiO₂ thin films have been prepared by sol–gel process. Their structure and optical properties have been investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and UV–vis spectroscopy. It has been observed that C dopants retard the transformation from anatase-to-rutile phase. Namely, C doping effect is attributed to the anatase phase stabilization. The optical analyses show that the optical band gap of anatase C-doped TiO₂ decreases with increasing amount of C. Also, it is founded that C dopants have been shown to make TiO₂ have a visible light photoresponse.     

Synthesis and characterization of monodispersed CdS nanoparticles in SiO2 fibers by sol–gel method

Cadmium sulfide (CdS) has been synthesized by a sol–gel route in order to obtain chemically protected, stable nanoparticles. The CdS nanoparticles in the SiO₂ gel matrix were dried to form monoliths of 1 in. diameter. The TEOS:H₂O:HCl:C₂H₅OH and TEOS/Cd mole ratios were varied to obtain narrow size distributed CdS nanoparticles. The UV absorption measurements indicated sharp absorption at 260 and 350 nm for different precursor compositions. SiO₂ gel containing the CdS nanoparticles was spin coated onto substrates in order to monitor the surface morphology of the samples. Scanning electron microscope measurements revealed formation of CdS nanoparticles within the branches of gel-network. Depending upon the mole ratio of additives and drying method, fibers or monolithic tablets of CdS nanoparticles could be produced.     

Optical properties of γ-Fe2O3 nanoparticles dispersed on sol–gel silica spheres

Two types of γ-Fe₂O₃ nanoparticles, pure γ-Fe₂O₃ and γ-Fe₂O₃ dispersed on sol–gel silica spheres (γ-Fe₂O₃/SiO₂) in thin film form were prepared by the sol–gel technique. Transmission electron microscopy, X-ray diffraction, optical transmittance and FTIR studies along with photoluminescence measurements were carried out for characterizing the samples. The X-ray diffraction patterns of both γ-Fe₂O₃ nanoparticles and γ-Fe₂O₃/SiO₂ indicated their phase-pure forms which were supported by the FTIR spectra. The average sizes of the nanoparticles obtained from transmission electron microscopy studies were 4 nm for both types of samples. Optical transmittance studies indicated direct allowed transitions with two band gaps at 2.43 and 3.07 eV. Although both types of samples showed excitonic luminescence at 2.38 eV (at room temperature), the luminescence intensity of the γ-Fe₂O₃/SiO₂ was higher than that of pure γ-Fe₂O₃.     

Preparation of LiMn2O4 thin films by a sol–gel method

LiMn₂O₄ thin films were prepared by a sol–gel method using spin-coating and annealing processes. Anhydrous Mn(CH₃COCHCOCH₃)₃ (manganese acetylacetonate) and LiCH₃COCHCO–CH₃ (lithium acetylacetonate) were chosen as source materials. The film electrochemical properties depended on the drying temperature even when subjected to the same annealing conditions. The discharge capacity of annealed film increased as the drying temperature was increased. However, the rate of capacity fading during cycling increased as the drying temperature was increased.     

Synthesis and microstructure of Ca-doped BaTiO3 ceramics prepared by high-energy ball-milling

The calcium-substituted barium titanate ceramics were prepared by solid state reaction technique. High-energy ball-milling was used for processing the powder. The microstructure of Ba_1−xCa_xTiO₃ ceramics was investigated by SEM techniques. The microstructure of Ba_1−xCa_xTiO₃ ceramics shows dense and uniform micrograph in all samples and the grain size is large. In this study the quantitative analysis of the ceramographs is shown and the variation of the different parameters with various doping concentration is discussed. Compositional analysis is ascribed to the occupancy of some Ca²⁺ to the Ti⁴⁺ sites.     

Structure and optical properties of sol–gel derived Gd2O3 waveguide films

Pure and rare earth doped gadolinium oxide (Gd₂O₃) waveguide films were prepared by a simple sol–gel process and dip-coating method. Gd₂O₃ was successfully synthesized by hydrolysis of gadolinium acetate. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were used to study the thermal chemistry properties of dried gel. Structure of Gd₂O₃ films annealed at different temperature ranging from 400 to 750 °C were investigated by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results show that Gd₂O₃ starts crystallizing at about 400 °C and the crystallite size increases with annealing temperature. Oriented growth of (4 0 0) face of Gd₂O₃ has been observed when the films were deposited on (1 0 0) Si substrate and annealed at 750 °C. The laser beam (λ=632.8 nm) was coupled into the film by a prism coupler and propagation loss of the film measured by scattering-detection method is about 2 dB/cm. Luminescence properties of europium ions doped films were measured and are discussed.     

Water and oil wettability of hybrid organic–inorganic titanate–silicate thin films deposited via a sol–gel route

Hybrid organic–inorganic titanate–silicate thin films were deposited on silicium wafer via a sol–gel route. Hybrid sols were formulated by mixing an inorganic titanium alkoxide solution with solutions of hybrid organic–inorganic silicon alkoxides partially substituted with non-hydrolysable alkyl chains. Three organo-silicate precursors were used to introduce methyl, octyl, or hexadecyl chains in the oxide network. Physico-chemical and morphological properties of derived hybrid films have been studied by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, ellipsometry, and atomic force microscopy. Contact angle measurements have also been performed to assess the water and mineral oil wettability of hybrid films. Wettability properties of these films are discussed with respect to physico-chemical and morphological features. It is shown that increasing the fraction and length of alkyl chains in the oxide network conjointly increases water and oil contact angles measured on such hybrid films.     

Self-compensation characteristics of Eu ions in BaTiO3

In order to clarify whether the mixed valence of Eu²⁺/Eu³⁺ exists in a self-compensation mode in Eu-doped BaTiO₃, the site occupation and valence state of Eu ions in barium titanate were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM), electron spin resonance (ESR), Raman spectroscopy (RS), and dielectric measurements. The results indicate that Eu ions may enter both Ba- and Ti-sites as Eu³⁺, forming a self-compensation mode with the amphoteric behavior. Self-compensation characteristics of Eu ions in BaTiO₃ are reflected by an expansion in unit cell volume, evolution of the 830 cm^− 1 Raman band, strong diffusion of the dielectric peak, disappearance of the Eu²⁺ ESR broad signal, and a g = 2.004 signal independent of temperature.     

Epitaxial growth of highly transparent and conducting Sc-doped ZnO films on c-plane sapphire by sol–gel process without buffer

Highly transparent and conductive scandium doped zinc oxide (ZnO:Sc) films were deposited on c-plane sapphire substrates by sol–gel technique using zinc acetate dihydrate [Zn(CH₃COO)₂·2H₂O] as precursor, 2-methoxyethanol as solvent and monoethanolamine as a stabilizer. The doping with scandium is achieved by adding 0.5 wt% of scandium nitrate hexahydrate [(ScNO₃·6H₂O)] in the solution. The influence of annealing temperature (300–550 °C) on the structural, optical and electrical properties was investigated. X-ray Diffraction study revealed that highly c-axis oriented films with full-width half maximum of 0.16° are obtained at an annealing temperature of 400 °C. The surface morphology of the films was judged by SEM and AFM images which indicated formation of grains. The average transmittance was found to be above 92% in the visible region. ZnO:Sc film, annealed at 400 °C exhibited minimum resistivity of 1.91 × 10⁻⁴ Ω cm. Room-temperature photoluminescence measurements of the ZnO:Sc films annealed at 400 °C showed ultraviolet peak at 3.31eV with a FWHM of 11.2 meV, which are comparable to those found in high-quality ZnO films. Reflection high-energy electron diffraction pattern confirmed the epitaxial nature of the films even without introducing any buffer layer.     

Structure and dielectric studies of nano-composite Fe2O3: BaTiO3 prepared by sol-gel method

Nano-structure pure barium titanate (BaTiO₃) and that was doped with iron oxide (Fe₂O₃), have been prepared by sol-gel method, using barium acetate (Ba(Ac)₂) and titanium butoxide (Ti(C₄H₉O)₄), as precursors. The as-grown prepared samples by sol-gel technique were found to be amorphous, which crystallized to the tetragonal phase after synthesized at 750 °C in air for 1 h as detected from the XRD patterns. The XRD data were confirmed by transmission electron microscope (TEM). The dielectric properties namely; dielectric constant (ε′) and loss tangent (tan δ) in the frequency range between 42 Hz and 1 MHz, at range of temperature 25-250 °C were investigated. The temperature dependence of ε′ and tan δ for the undoped and doped materials, at 1 kHz, was also investigated. As a result, tan δ increased rapidly with decreasing temperature below 125 °C (Curie temperature) while above this temperature, tan δ shows temperature independent. As a result, below and above Curie temperature, ferroelectric phase and paraelectric phase of BaTiO₃ can be obtained, respectively.     

Synthesis and transport properties of La2NiO4

La₂NiO₄ compounds were prepared by a modified sol–gel auto-combustion method, which is a low-temperature combustion synthesis procedure using microwave-assisted sol–gel as precursors. The high-temperature transport properties of the samples were investigated. The band structure, total density of states (DOS), and partial density of states (PDOS) of low-temperature orthorhombic (Bmab) phase and high-temperature tetragonal (I4/mmm) phase for La₂NiO₄ were calculated in order to study the transport properties of the as-obtained samples.     

Influence of pH on characteristics of BaFe12O19 powder prepared by sol–gel auto-combustion

BaFe₁₂O₁₉ powders with nanocrystalline sizes were produced by sol–gel auto-combustion. Fe³⁺ and Ba²⁺, in a molar ratio of 11.5, were chelated by citric acid ions at different pH. After dehydration, auto-combustion and calcinations, BaFe₁₂O₁₉ powders were formed. TG/DSC indicated the action to form BaFe₁₂O₁₉ first occurred at about 800. XRD patterns of the annealed powders showed that the well-crystalline powder was produced when pH=10. In addition, the data from XRD showed the lattice parameters a and c, and the unit-cell volume V had a little decrease and the density went up with the increasing pH. The data from PPMS exhibited that pH in the starting solution had an important influence on magnetic properties. In this case, BaFe₁₂O₁₉ powder, of maximum magnetization M(3 T)≈60 A m²/kg, the remanent magnetization M_r≈33 A m²/kg and the intrinsic coercive H_c≈432 kA/m, was produced under the molar ratio of citric acid to the metal nitrate of 1.5 when pH=10.     

Structural and optical properties of Ba(Ti1−x,Nix)O3 thin films prepared by sol–gel process

Ba(Ti_1−x,Ni_x)O₃ thin films were prepared on fused quartz substrates by a sol–gel process. X-ray diffraction and Raman scattering measurements showed that the films are of pseudo-cubic perovskite structure with random orientation and the change of lattice constant caused by Ni-doping with different concentrations is very small. Optical transmittance spectra indicated that Ni-doping has an obvious effect on the energy band structure. The energy gap of Ba(Ti_1−x,Ni_x)O₃ decreased linearly with the increase of Ni concentration. It indicates that the adjusting of band gap can be achieved by controlling the Ni-doping content accurately in Ba(Ti_1−x,Ni_x)O₃ thin films. This has potential application in devices based on ferroelectric thin films.     

Studies of sol–gel TiO2 and Pt/TiO2 catalysts for NO reduction by CO in an oxygen-rich condition

The textural properties, morphological features, surface basicity and oxygen reduction behaviours of titania and Pt supported titania catalysts synthesized via a sol–gel method were studied by means of N₂ physisorption, SEM, TEM, CO₂-TPD and H₂-TPR techniques. Mesostructured TiO₂ shows a very narrow pore size distribution that uniformly centred at about 4 nm. High resolution TEM images confirmed that most of Pt particles on Pt/TiO₂-SG had a size smaller than 2 nm. Both the titania support and Pt loaded catalysts chiefly contained weak basic sites with small amount of strong basic sites. Loading Pt did not significantly alter the surface reduction characters of titania, indicating a weak interaction between Pt metals and titania support. Catalytic evaluation revealed that the selectivity of NO reduction over titania was insensitive to variation of textural property. On the bare titania, low NO conversion but high selectivity to N₂O was obtained. However, the Pt/TiO₂-SG catalysts exhibited high NO conversion and high selectivity to N₂, which is assumed to relate to NO dissociation catalysed by the metallic Pt clusters. In addition, when the reaction temperature was above 200 °C, 3–11% NO₂ was yielded over the Pt/TiO₂-SG catalysts, which was discussed on a basis of reaction competition, metal-support interaction and NO dissociation.     

On the origin of 1.5 μm luminescence in porous silicon coated with sol–gel derived erbium-doped Fe2O3 films

Sol–gel derived Fe₂O₃ films containing about 10 wt% of Er₂O₃ were deposited on porous silicon by dipping or by a spin-on technique followed by thermal processing at 1073 K for 15 min. The samples were characterized by means of PL, SEM and X-ray diffraction analyses. They exhibit strong room-temperature luminescence at 1.5 μm related to erbium in the sol–gel derived host. The luminescence intensity increases by a factor of 1000 when the samples are cooled from 300 to 4.2 K. After complete removal of the erbium-doped film by etching and partial etching the porous silicon, the erbium-related luminescence disappears. Following this, luminescence at 1.5 μm originating from optically active dislocations (“D-lines”) in porous silicon was detected. The influence of the conditions of synthesis on luminescence at 1.5 μm is discussed.     

Effects of substitution of Ti for Fe in BiFeO3 films prepared by sol–gel process

Ti substituted BiFe_1−xTi_xO_3+δ films have been prepared on indium–tin oxide (ITO)/glass substrates by the sol–gel process. The films with x=0.00–0.20 were prepared at an annealing temperature of 600 °C. X-ray diffraction patterns indicate that all films adopt R3m structure and the films with x=0 and 0.10 show pure perovskite phase. Cross-section scanning shows the thickness of the films is about 300 nm. Through 0.05 Ti substitution, the 2P_r increases to 8.30 μC/cm² from 2.12 μC/cm² of the un-substituted BiFeO₃ film and show enhanced ferroelectricity at room temperature. The 2P_r values are 2.63 and 0.44 μC/cm² for the films with x=0.01 and 0.2, respectively. Moreover, the films with x=0.05 and 0.10 show enhanced dielectric property since the permittivity increases near 150 at the same measuring frequency. Through the substitution of Ti, the leakage conduction is reduced for the films with x=0.05–0.20.     

Synthesis and optical properties of Ce-doped Y3Mg2AlSi2O12 phosphors

Y_3−xMg₂AlSi₂O₁₂:Ce_x³⁺ (x=0.015, 0.03 and 0.06) phosphors possessing garnet crystal structure were synthesized by the sol–gel combustion technique. The samples were characterized by application of powder X-ray diffraction (XRD), photoluminescence (PL) spectroscopy, thermal quenching (TQ) and scanning electron microscopy (SEM). Moreover, luminous efficacies (LE), color points and quantum efficiencies (QE) were calculated. Optical properties were studied as a function of Ce³⁺ concentration and annealing temperature. XRD analysis revealed that sintering of polycrystalline Y₃Mg₂AlSi₂O₁₂:Ce³⁺ powders at 1550 °C results in nearly single-phase garnet materials. Phosphors showed broad emission band in the range of 500–750 nm and had the maximum intensity at 600 nm, which results in strongly red-shifted phosphors compared with conventional YAG:Ce phosphors emitting at 560 nm. However, strong concentration quenching has also been observed, probably due to increased Stokes shift.