Effect of hydration andpH on the thermal stability of proteinase K

The effect of hydration andpH on the thermal stability of proteinase K was studied in the temperature range 310–450 K by differential scanning calorimetry. The dependences of the denaturation temperatureT _d, the specific enthalpy of denaturation H _d and the maximum of excess apparent specific heat capacityC _ex ^max upon the degree of hydrationh and thepH of the buffers used are presented. The relation betweenT _d andh is of the Flory-Garrett's type. By means of Ooi's model, the two components of the denaturation enthalpy arising from hydration and conformational change, respectively, were estimated. The fact that the specific denaturation enthalpy of proteinase K is very low may be attributed to its very low enthalpy of conformational change per heavy atom.Dedicated to Prof. Menachem Steinberg on the occasion of his 65th birthdayThis major project was supported by the National Natural Science Foundation of China.     

Effect oftrans-polyoctenamer on thermal stability of rubbers determined by thermal analysis

An effect of a cyclic low molecular-weight polymertrans-polyoctenamer rubber (TOR) on the thermal stability of diene rubbers and their vulcanizates was investigated. The investigation was carried out in the air and nitrogen atmospheres using thermogravimetry, DSC and simultaneous thermoanalytical methods. The thermal stability indexes:T ₅,T _max and activation energy of degradation (E), as well asT _g andT _m values, have been determined.It was found thattrans-polyoctenamer (TOR) increases of the thermal stability indices of raw diene rubbers and their vulcanizates. The results show that the thermal degradation of diene rubbers occurred at higher temperature if they were blended with TOR. In our opinion, intermolecular structures formed between the cyclic low-molecular weight polymer and some linear rubber molecules may be the reason for the higher thermal stability of these rubber blends.The work was supported by State Committee for Research, Poland. Grant No. 7.T08 E 032-08.     

The effect of trimethylamine N-oxide on RNase a stability

The thermal stability of bovine pancreatic ribonuclease (RNase A) has been investigated in the presence of trimethylamine N-oxide (TMAO), a naturally occurring osmolyte, by means of differential scanning calorimetry (DSC) and circular dichroism (CD) measurements at neutral and acid pH conditions. It is well known that compatible osmolytes such as TMAO are effective in stabilizing protein structure and counteracting the denaturing the effect of urea and guanidinium hydrochloride (GuHCl). Calorimetric results show that TMAO stabilizes RNase A at pH 7.0 and does not stabilize the protein at pH 4.0. RNase A thermal denaturation in the presence of TMAO is a reversible two-state N ⇆ D process. We also show that TMAO counteracts the urea and GuHCl denaturing effect at neutral pH, whereas the counteracting ability is lost at acid pH.     

An effect of polymers on thermal stability of bitumens

Results of studies dealing with an effect of polymers (selected kinds) and plasticizer on thermal stability of coal-tar pitch were presented. Factors being decisive in miscibility of composition constituents and instability of bitumen-polymer-plasyticizer mixtures were determined.     

Kinetics and thermal stability of two peroxidase isozymes from Eupatorium odoratum

The Eupatorium odoratum leaf peroxidase exists as at least seven distinct isozymes (three cationic, three anionic, and one neutral). These isozymes were identified and separated by preparative iso-electric focusing. Thermal stability, including the activation enthalpy (ΔH ^*), free energy of inactivation (ΔG ^*) and activation entropy (ΔS ^*), and kinetic studies of two isozymes, one having a pI of 5.0 (E5) and another one having a pI of 7.0 (E7) with mol mass of 43 and 50 kD, respectively, were studied in detail. Of the molecular weight of E5 and E7, 25 and 32% correspond to the carbohydrate content of the isozymes. Optimal pH was in the acidic range of 3.6–3.8 for E5 and 3.8 for E7 with the oxidation of ABTS. E7 and E5 showed activation energy for inactivation, 194.8 and 145.4 kJ/mol, respectively. Both the isozymes showed distinct substrate specificity. The catalytic specificity constant for E5 and E7 were 112×10⁵ and 124×10⁵/s·M, respectively, when 2,2′-azino-bis-(3-ethylbenz-thiazoline-6 sulfonic acid) was used as the substrate. Maximum affinity (i.e., lowest K _m value) to H₂O₂ was shown by E5 and E7 along with Pyrogallol and was 0.02 and 0.05/s·M, respectively.     

Spectral,thermal and magnetic studies of 2-chloro-5-nitrobenzoates of rare earth elements(iii)

The conditions of the formation of yttrium(III) and lanthanide(III) 2-chloro-5-nitrobenzoates were studied and their quantitative composition and solubilities in water at 298 K were determined. The compounds are dihydrates and their solubilities are of the order of 10^-3 mol dm^-3. The FTIR, FIR and X-ray spectra for the complexes were recorded. All complexes are crystalline compounds. Their thermal decomposition was studied only in the range 293-523 K since on heating above 523 K the complexes decompose explosively. Hydrated 2-chloro-5-nitrobenzoates of rare earth elements lose two crystallization water molecules in one step. The enthalpy of dehydration process was established and the magnetic moments of the complexes were determined in the range 77-300 K. The compounds obey the Curie-Weiss law. The 4f electrons do not participate in the formation of the Ln-O bonds. This revised version was published online in August 2006 with corrections to the Cover Date.     

合成榍石的抗辐照稳定性和热稳定性

以H2SiO3、CaCO3、TiO2为原料,通过固相反应合成榍石,并对合成的榍石进行热处理和60Co源辐照试验,借助X射线衍射(XRD)、扫描电子显微镜(SEM)、红外光谱(IR)、激光拉曼光谱(LRS)等分析手段,研究合成榍石的抗辐照稳定性和热稳定性.结果表明,辐照累计剂量为5.76×105Gy的60Co源辐照没有造成榍石晶格的辐射损伤,合成的榍石具有良好的抗辐照稳定性;在200℃、400℃、600℃、800℃热处理24h,榍石晶体没有发生物相变化,合成榍石晶体具有良好的热稳定性.     

Thermal denaturation of bovine serum albumin and its oligomers and derivativespH dependence

In a previous paper, we report a preliminary DSC study on bovine (BSA) and human (HSA) serum albumins. However, at accurate HPLC analysis the commercial proteins show three peaks: Fraction V-I, probably globulins (as declared by the producers), Fraction V-II (about 15–18% of the product) and Fraction V-III that represents pure BSA or HSA. A hypothesis is that the Fraction II is a covalent dimer, or trimer or a mixture of both, generated during the scalf-life of the commercial product. Denaturation enthalpies of the purified Fraction V-III and Fraction V-II of BSA, have been determined calorimetrically, at changing thepH, and the results of both compared with those obtained on the untreated protein. Few calorimetric experiments have been also carried on a BSA monomer derivative with sulphidril group protected. Computer program have been developed for the deconvolution of exo- and endothermic effects and for the analysis of thermal denaturation profiles.     

About the synthesis and thermal stability of SiO2-aerogel

Aerogels are extremely porous high-tech materials based on inorganic oxides, especially silica. The paper describes synthesis and properties of SiO₂-aerogel, and changes occurring during heating of SiO₂-aerogel in the temperature range from 20 to 1000°C. Four thermoanalytical methods were used: Thermodilatometry, Differential thermal analysis, Thermogravimetry and Derivative thermogravimetry.     

Thermodynamic study of the thermal denaturation of a globular protein in the presence of different ligands

By means of difference UV-Vis spectra, the thermal denaturation of catalase has been studied in the presence of different surfactants: sodium perfluorooctanoate, sodium octanoate and sodium dodecanoate. These results indicate that hydrogenated surfactants play two opposite roles in the folding and stability of catalase, they act as a structure stabiliser at a low molar concentrations (enhancing T _m) and as a destabilizer at a higher concentrations (diminishing T _m). Meanwhile sodium perfluorooctanoate enhances T _m in the whole concentration range. An approach for the determination of the heat capacity, enthalpy and entropy has been made, finding that for the three studied surfactants, at all concentrations, the enthalpy term dominates the entropy term.     

Effect of substituents (NH2, OH, F) on structures and stability of lithofluorosilylenoids

Isomeric structures and energies of three kinds of lithofluorosilylenoids, R₂SiLiF (R = NH₂, OH, F) were studied using theab initio molecular orbital theory. The calculations show that thermal stability of the three-membered ring structures of these three kinds of silylenoids decreases in the order of substituents NH₂ > OH > F because of the conjugation between NH₂, OH or F and Si atom. The interaction of substituents R with Li atom makes R₂SiLiF have a structure with two Li-A-Si-F (A = N, O, F) four-membered rings, which is the most stable of the isomers of each of three kinds of silylenoids and whose stability decreases in the order of substituents F > OH > NH₂. Inductive effect of substituents influences the thermal stability of the linear structure of silylenoids.     

The effect of bioindicator preparation and storage on thermal resistance of Bacillus stearothermophilus spores

Paper strips inoculated with spores of Bacillus stearothermophilus ATCC 7953 were conventionally dried (lot 1) and lyophilized (lot 2); stored in defined environments of 32 and 86% relative humidity at 10, 25 and 33°C for 210 d; and submitted to moist heat treatments at 121°C. A significant decrease in thermal resistance from initial starting levels was found for lyophilized bioindicators stored at 86% relative humidity. The respective average D _121°C values were 1.55 ± 0.05 and 1.37 ± 0.10 min for lyophilized bioindicators stored at 32 and 86% relative humidity; and 1.65±0.15min and 1.57 ± 0.11 min for dried bioindicators stored in the same environments.     

苯并三呋咱氧化物中主要杂质对其热安定性的影响

根据苯并三呋咱氧化物（BTF）中主要杂质的种类，分别选择了三叠氮三硝基苯（TNTAB）、三氯三硝基苯（TCTNB）和叠氮化钠（NaN3)作为杂质研究对象，采用机械混合的方法制备了一系列不同配比的BTF混合物，再通过差热（DTA）、差示扫描量热（DSC）、真空安定性试验（VST）、布氏压力法、热失重、5s爆发点等热分析方法进行测试，结果表明TCTNB和NaN3对BTF热安定性影响较小，而TNTAB是影响BTF热安定性的主要因素。     

Preparation of the individual compact single-chain globular particulates of Poly(N-isopropylacrylamide)

The compact single-chain (SC) particulates of Poly(N-isopropylacrylamide) (PNIPAM), which have been formed above its lower critical solution temperature in an aqueous solution containing the surfactant of sodium n-dodecyl sulfate (SDS), were recovered from the solution by freeze-drying. Under scanning electron microscopy, the compact particulate appears as a spherical or elliptical particulate individually dispersed in SDS, which acts as a solid solvent to prevent agglomeration. The conformation of the compact SC particulates of PNIPAM dispersed in SDS had been studied by the solid-state high-resolution ¹³C NMR spectroscopy. The ¹³C spin-lattice relaxation time T ₁ of the SC sample was determined in comparison with that of the original one. It was found that the T ₁ of the methyl carbon in the isopropyl group of the SC sample was about 45% higher than that in the original multichain sample, which revealed the differences in the motion of the methyl group in the different condensed states and illuminated the characteristic conformation of the compact SC globular particulates of PNIPAM.     

聚乙烯醇缩丁醛热稳定性能的研究

本文通过两步加料法合成了聚乙烯醇缩丁醛(PVB)树脂并对其热稳定性进行了研究.由热老化和热重数据可知,碱金属和碱土金属氢氧化物NaOH、Ca(OH)2、Ba(OH)2的加入分别在不同程度上提高了PVB树脂热稳定性,比较发现,Ba(OH)2的热稳定效率最高.此外,本文通过红外光谱和紫外光谱分析,对碱的热稳定机理进行了探讨,结果表明碱之所以能够延缓PVB高温下的热降解,是因为碱可以阻碍PVB受热后缩醛开环和共轭结构的形成.     

Chemical and thermal stability of isotypic metal-organic frameworks: effect of metal ions

Chemical and thermal stabilities of isotypic metal-organic frameworks (MOFs) like Al-BDC (Al-benzenedicarboxylate called MIL-53-Al), Cr-BDC (MIL-53-Cr) and V-BDC (MIL-47-V), after purification to remove uncoordinated organic linkers, have been compared to understand the effect of the central metal ions on the stabilities of the porous MOF-type materials. Chemical stability to acids, bases, and water decreases in the order of Cr-BDC>Al-BDC>V-BDC, suggesting stability increases with increasing inertness of the central metal ions. However, thermal stability decreases in the order of Al-BDC>Cr-BDC> V-BDC, and this tendency may be explained by the strength of the metal-oxygen bond in common oxides like Al(2)O(3), Cr(2)O(3), and V(2)O(5). In order to evaluate precisely the stability of a MOF, it is necessary to remove uncoordinated organic linkers that are located in the pores of the MOF, because a filled MOF may be more stable than the same MOF after purification.     

The thermal degradation kinetics of poly(di-n-alkylitaconates)

The non-oxidative thermal degradation kinetics of poly(di-n-alkyl itaconates), ranging from the methyl to then-octyl derivatives, were studied by non-isothermal and isothermal TG. The thermal degradation activation energy and characteristic mass loss temperatures were found to decrease with increasing substituent size. The shapes of the DTG curves were dependent on the size of the alkyl substituent. The different DTG maxima were ascribed to various modes of initiation of depolymerisation. The thermal stability of poly(di-n-hexyl itaconate) was found to be independent of the initial molar mass of the sample in the range ofM _w from 10⁴ to 10⁷ g/mol.

---

Zusammenfassung Mittels nichtisothermer und auch isothermer TG wurde die nichtoxidative thermische Zersetzungskinetik von Poly(di-n-alkylitakonaten) untersucht, dabei bewegt sich die Länge der Alkylkette von Methyl bisn-Oktyl. Die Aktivierungsenergie der thermischen Zersetzung und die charakteristischen Masseverlusttemperaturen nehmen mit steigender Substituentlänge ab. Aussehen der DTG-Kurven hängt von der Größe der Alkylkette ab. Die verschiedenen DTG-Maxima wurden verschiedenen Initiierungs schritten der Depolymerisierung zugeschrieben. Man fand, daß im Intervall M_w zwischen 10⁴ und 10⁷ g·mol die thermische Stabilität der Poly(di-n-hexylitakonate) unabhängig von der anfänglichen molaren Masse der Probe ist.

     

The effect of photocrosslinkable groups on thermal stability of bulk heterojunction solar cells based on donor–acceptor‐conjugated polymers

Three different types of photocrosslinkable groups into a low band‐gap donor–acceptor‐conjugated polymer, namely poly{benzo[1,2‐b:4,5‐b′]dithiophene‐alt‐ thieno[3,4‐b]thiophene} (PBT), were developed to comparatively investigate the effect of the photocrosslinkable groups on the thermal stability of bulk heterojunction solar cells. Compared with vinyl groups, bromine‐ and azide‐ photocrosslinkable groups are more prompt for photocrosslinking to yield a denser crosslinking network, probably due to the different crosslinking mechanisms and reaction rates. In contrast to the reference device decreasing to less than 10% of its initial efficiency value after 80 h of annealing at 150 °C, a great improvement in the thermal stability of performance of all these crosslinked functional copolymers devices demonstrates that photocrosslinking can effectively improve the thermal stability of the active layer by suppressing [6,6]‐phenyl‐C₆₁‐butyric acid methyl diffusion and phase separation. Furthermore, the solar cells with crosslinked bromine‐ and azide‐functionalized PBT polymers showed very thermally stable photovoltaic device performance by retaining 78 and 66% of their initial device efficiency, respectively, whereas vinyl‐functionalized PBT devices retained only 51% of its initial value after long‐time thermal annealing. This suggests that an appropriate crosslinking network with homogenous active morphology could dramatically enhance the device stability without sacrificing the performance. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4156–4166     

The kinetic behaviour and thermal stability of commercially available explosives

Summary Manufactures of commercially available explosives guarantee a certain lifetime of their products. In the commercial field this lifetime is usually large enough. The explosive is normally used long before the end of its lifetime. It may happen that these explosives are stored for a long time in a bunker where they sometimes exceed their lifetime. A large set of commercial explosives is characterized with a TG by heating small samples in aluminium sample cups from room temperature to 550°C, under a nitrogen atmosphere, with three different heating rates (2, 5 and 10 K min^-1). The activation energy of the decomposition step is determined in several different ways. After this characterization, a selection of the samples (based on economical value) is artificially aged for periods of 2, 4 and 6 weeks. After these ageing profiles the samples are re-investigated with the TG under the same conditions (heating rates and atmosphere) followed by the calculation of the kinetic parameters of the artificially aged materials. According to the TG measurements almost all tested explosives appear to have a much longer lifetime than the values given by the manufacturer. From kinetic point of view, the different methods for calculating the activation energy result in approximately the same parameters. It may conclude that TG seems to be a reliable and quick method for the determination of the lifetime of commercial explosives.     

The effect of terminal epoxy modification on the mesomorphic and thermal stability of biphenyl ester liquid crystals

ABSTRACT

A series of biphenyl ester compounds with alkenyl, alkyl, oxirane, and 1,3-dioxolane as the terminal groups have been synthesised for investigating the mesomorphic and thermal stability. Based on the same carbon skeleton, the allyl-terminated compound V1OLC has no mesophase, while the oxirane-terminated compound POLC not only has wider multiple smectic mesophase compared with the propyl-terminated compound 3OLC but also exhibits the best thermal stability. However, when the terminal groups change from oxirane to 1,3-dioxolane, EOLC shows neither mesophase nor the good thermal stability. In addition, with the extension of the terminal chains, the butyl-terminated compound 4OLC gives the widest smectic mesophase. These imply that the mesomorphic and thermal stability of these biphenyl ester compounds are dependent on the suitable terminal chain lengths and epoxy sizes. Meanwhile, Density Functional Theory (DFT) calculations were conducted to assist in analysing the experimental results.