Organic hybrid of chlorinated polyethylene and hindered phenol. III. Influence of the molecular weight and chlorine content of the polymer on the viscoelastic properties

The influences of the molecular weight and chlorine content of chlorinated polyethylene (CPE) on the dynamic mechanical propertiesof an organic hybrid consisting of CPE and 3,9‐bis[1,1‐dimethyl‐2{β‐(3‐tert‐butyl‐4‐hydroxy‐5‐methylphenyl)propionyloxy}ethyl]‐2,4,8,10‐tetraoxaspiro[5,5]‐undecane (AO‐80) were investigated. All CPE/AO‐80 hybrids clearly exhibited two kinds of relaxations, and their magnitudes varied according to the molecular weight and chlorine content of CPE. This was due to a change in the ratio of AO‐80 molecules dispersed in the CPE‐rich domain and the AO‐80‐rich domain. A comparison of the jump intensity in differential scanning calorimetry curves with the maximum value of the second tan δ peak demonstrated that the second relaxation was caused by the dissociation of intermolecular hydrogen bonding within the AO‐80‐rich domain. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2943–2953, 2000     

Organic hybrid of chlorinated polyethylene and hindered phenol. IV. Modification on dynamic mechanical properties by chlorinated paraffin

Binary systems of chlorinated polyethylene (CPE) and chlorinated paraffin (CP) or 3,9‐bis[1,1‐dimethyl‐2{β‐(3‐tert‐butyl‐4‐hydroxy‐5‐methylphenyl) propionyloxy}ethyl]‐2,4,8,10‐tetraoxaspiro[5,5]‐undecane (AO‐80) and their ternary systems were investigated by dynamic mechanical analysis, thermal analysis, and infrared spectrum analysis. Adding CP into CPE/AO‐80, in which one novel relaxation appears above the glass‐transition temperature of CPE, can increase not only the peak height but also the minimum value between two peaks. The tan δ value in the middle of the two peaks for CPE/CP/CPE was found to be proportional to the slope (d ln E′/dT) of the E′ curve at an identical temperature. The addition of CP caused changes in many of the hydrogen bonds: a decrease in hydrogen bonds between the hydroxyl groups of AO‐80, a reinforcement of hydrogen bonds between the hydroxyl groups of AO‐80 and α‐hydrogens of CPE, and the formation of other hydrogen bonds between the carbonyl groups of AO‐80 and α‐hydrogens of CPE. Those changes are useful to improve the temperature dependence of tan δ and to enhance the stability of the dynamic mechanical properties. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 23–31, 2001     

Organic hybrid of chlorinated polyethylene and hindered phenol. II. Influence of the chemical structure of small molecules on viscoelastic properties

The viscoelastic properties and stabilities of those properties of organic hybrids consisting of chlorinated polyethylene (CPE) and tetrakis[methylene‐3‐(3‐5‐di‐tert‐butyl‐4‐hydroxy phenyl)propionyloxy]methane (AO‐60) and triethylene glycol bis[3‐(3‐tert‐butyl‐4‐hydroxy‐5‐methyl phenyl)propionyloxy] (AO‐70) were investigated. The CPE/AO‐70 hybrids show only one transition, whereas for the CPE/AO‐60 hybrids, one novel relaxation appears above the glass‐transition temperature of CPE. This relaxation on the higher temperature side in the mechanical spectrum for CPE/AO‐60 is associated with the appearance of the AO‐60‐rich phase. Furthermore, the stabilities of the viscoelastic properties and microstructures of the organic hybrids consisting of CPE and multifunctional hindered phenols are dominated by the strength of the intermolecular interaction between CPE and phenols and the conformations of the middle skeletal parts of hindered phenols. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1496–1503, 2000     

Crystallization of a vitrified hindered phenol within chlorinated polyethylene and its effects on dynamic mechanical properties

The effects of heat treatment below the melting point of 3,9‐bis{1,1‐dimethyl‐2[β‐(3‐tert‐butyl‐4‐hydroxy‐5‐methylphenyl)propionyloxy]ethyl}‐2,4,8,10‐tetraoxaspiro[5,5]‐undecane (AO‐80) on the thermal and dynamic mechanical properties and microstructure of chlorinated polyethylene (CPE) filled with vitrified AO‐80 particles were investigated. The initial AO‐80 was a complete crystal, whereas AO‐80 obtained by cooling from its melting state was amorphous. The vitrified AO‐80 particles could crystallize again in a CPE matrix by an annealing treatment, but this crystal was different from the initial AO‐80 in the microstructure. In addition, the incorporation of CPE chains caused a dramatic increase in the modulus. As a result, the AO‐80 crystal particles that contained some CPE chains acted as multifunctional crosslinks, and the CPE/AO‐80 hybrid was found to be a new type of elastomer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 209–215, 2004     

ENHANCEMENT OF DAMPING PERFORMANCE OF POLYMERS BY FUNCTIONAL SMALL MOLECULES

The addition effects of organic small molecular substances N,N'-dicyclohexyl-benzothiazyl-2-sulfenamide(DZ)and 3,9-bis{1,1-dimethyl-2[β-(3-tert-butyl-4-hydroxy-5-methylphenyl)propionyloxy]ethyl}-2,4, 8, 10-tetraoxaspiro [5,5]-un-decane (AO-80) on the dynamic mechanical properties of chlorinated polyethylene (CPE), chlorinated polypropylene (CPP),acrylate rubber (ACM) and their blends were investigated. In the case of compatible systems such as CPE/DZ and ACM/AO-80, the height of the loss tangent (tanδ) peak of a matrix polymer (CPE or ACM) increases, and its peak position shifts to ahigher temperature with the addition of DZ or AO-80. By contrast, for incompatible CPE/AO-80, a novel transition appearedabove the glass transition temperature of CPE. This additional transition was assigned to dissociation of the intermolecularhydrogen bond between the α-hydrogen of CPE and the hydroxyl groups of AO-80 within the AO-80-rich domain. This willprovide a new concept for developing damping material. However, the minimum value between two tanδ peaks is lower. Itwas found that the temperature dependence of tanδ could be improved by adding chlorinated paraffin (CP) or ACM toCPE/AO-80. In addition, another ternary system of ACM/CPP with more AO-80 was found to be a very good self-adhesivedamping material because of the appearance of a novel transition due to an interfacial layer of ACM/CPP.     

A NOVEL SECOND-ORDER TRANSITION IN ORGANIC HYBRIDS CONSISTING OF POLYMERS AND SMALL MOLECULES

A novel transition appeared above thc glass transition temperature of chlorinated polyethylene (CPE) for binaryblends of CPE and additives such as organic small molecules or oligomers. This transition was assigned to the dissociation ofintermolecular hydrogen bonds between the polymer ard additive within the edditive rich phase. Of particular interest is thata novel pyramid crystal was observed in the annealed CPE/hindered phenol blends. Another intriguing observation is thatthese polymer/small molecule blends organized by intermolecular hydrogen bonding have several potential properties, suchas shape-memorization, self-restoration, self-adhesiveness and super damping.     

Viscoelastic properties of an organic hybrid of chlorinated polyethylene and a small molecule

The dynamic mechanical properties of an organic hybrid consisting of chlorinated polyethylene (CPE) and N,N‐dicyclohexyl‐2‐benzothiazolyl sulfenamide (DZ) were investigated. All the CPE/DZ hybrids showed a single loss tangent (tan δ) peak in the mechanical spectra. The peak area under the tan δ/temperature curves around the mechanical loss peak was examined to characterize the damping properties of the CPE/DZ hybrids. We found that there exists a bending point in the relation between the glass‐transition temperature (T_g) and DZ content and that the value of T_g is saturated in the higher DZ contents, suggesting that excess DZ molecules show self‐aggregation and are reorganized. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1341–1347, 2000     

Physically crosslinked elastomers prepared from oligomeric polyolefins with mesogenic units

Two ABA‐type liquid crystalline oligomers were newly synthesized, where A was a mesogenic group and B was polyolefin whose molecular mass was 2470. The A segment was prepared from p‐hydroxyl benzoic acid and terephalic acid. The elastomeric films, whose moduli at 20% elongation were 0.4–1.0 MPa, were obtained by solution casting of the ABA‐type oligomers. Dynamic mechanical analysis and differential scanning calorimetry measurement showed the glass transition of amorphous polyolefin segments, the melting of mesogenic groups, and the meso‐to‐isotropic transition of liquid crystalline phase. The formation of microphase‐separated structures was confirmed by a small‐angle X‐ray scattering (SAXS) measurement. The presence of hexagonal cylinder domains, which were attributed to the aggregation of mesogenic groups in the polyolefin matrix, was also detected by SAXS. These liquid crystalline oligomers showed anisotropy under the crossed Nicoles, and the textures were observed to be nematic. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2247–2253, 2000     

Birefringence control by hydrogen bonding on compatible polymer pair composed of hydrogenated ring‐opening polymer and modified polystyrene

A new polymer blend composed of a hydrogenated ring‐opening polymer (HROP) with an ester group and hydroxyl functionalized polystyrene (HFP) produced the excellent transparent materials which enabled a precise birefringence control in keeping with the other physical properties for optical film use. The blend with a composition from 0.28 to 0.35 for the HFP weight fraction showed an extraordinary wavelength dispersion, transmitting through a zero birefringence point at the critical fraction of 0.45, while each polymer showed an ordinary wavelength dispersion. The observed excellent transparency even above those of the glass transition temperature was attributed to a depressed phase separation that resulted from strong hydrogen bond between the ester and hydroxyl groups. An IR analysis of the film demonstrated a remarkable red‐shift in the carbonyl peak with an increase of the hydroxylated polystyrene content, indicating a strong hydrogen bond between those groups. This new polymer blend provides a useful design to achieve practical demands for film use, both optical and mechanical under the fabrication conditions using the melt extrusion technique. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3132–3143     

Studies on poly(ε‐caprolactone)/thiodiphenol blends: The specific interaction and the thermal and dynamic mechanical properties

The effects of several low molecular weight compounds with hydroxyl groups on the physical properties of poly(ε‐caprolactone) (PCL) were investigated by Fourier transform infrared (FTIR) spectroscopy and high‐resolution solid‐state ¹³C NMR. PCL and 4,4′‐thiodiphenol (TDP) interact through strong intermolecular hydrogen bonds and form hydrogen‐bonded networks in the blends at an appropriate TDP content. The thermal and dynamic mechanical properties of PCL/TDP blends were investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis, respectively. The melting point of PCL decreased, whereas both the glass‐transition temperature and the loss tangent tan δ of the blend increased with an increase in TDP content. The addition of 40 wt % TDP changed PCL from a semicrystalline polymer in the pure state to a fully amorphous elastomer. The molecules of TDP lost their crystallizability in the blends with TDP contents not greater than 40 wt %. In addition to TDP, three other PCL blend systems with low molecular weight additives containing two hydroxyl groups, 1,4‐dihydroxybenzene, 1,4‐di‐(2‐hydroxyethoxy) benzene, and 1,6‐hexanediol, were also investigated with FTIR and DSC, and the effects of the chemical structure of the additives on the morphology and thermal properties are discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1848–1859, 2000     

Synthesis and characterization of fluorinated benzoxazole polymers with high Tg and low dielectric constant

Next generation microelectronic packaging requirements are driving the need to produce increasingly lower dielectric constant materials while maintaining high thermal stability and ease of processing. Efforts have focused on the synthesis and analysis of new polymers with the goals of high thermal stability [degradation temperature (T_d) > 400 °C, low glass‐transition temperature (T_g) > 350 °C], low water uptake (<1%), solubility in selected organic solvents, dielectric constant less than 2.5, and low thermal expansion coefficient. These stringent combined goals have been largely achieved with flexible aromatic benzoxazole polymers. Intramolecular hydrogen bonding between pendant hydroxyl groups and the double‐bond nitrogen of the benzoxazole has been exploited to increase the polymer T_g, whereas the incorporation of perfluoroisopropyl units effectively decreases the dielectric constant. Out‐of‐plane impedance measurements on films of materials in this family (38–134 μm thick) have resulted in typical dielectric values of 2.1–2.5 at 1 MHz, depending on copolymer ratios and functionalizations. Results have been correlated with optical waveguide measurements of films 4‐μm thick to determine film anisotropy and the high‐frequency dielectric constant, and have been corroborated by in‐plane interdigitated electrode dielectric measurements on samples 0.75 μm thick. Candidate materials exhibited extremely low water uptake (0.2%) even after submersion in boiling water for several days. Dynamic mechanical analysis of the polymers enabled the determination of the influence of intermolecular hydrogen bonding on the T_g and loss tangent magnitude. Finally, the coefficient of thermal expansion has been examined and correlated with copolymer constitution. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1991–2003, 2000     

EFFECTS OF MOLECULE AGGREGATION STATE OF HINDERED PHENOL ON DYNAMIC MECHANICAL PROPERTIES OF CHLORINATED POLYETHYLENE*

Hindered phenol compound 3,9-bis{1,1-dimethyl-2[β-(3-tert-butyl-4-hydroxy-5-methylphenyl)propionyloxy]ethyl}-2,4,8,10-tetraoxaspiro[5,5]-undecane (AO-80) is a polymorphous material with different physical structures. The initial AO80 is highly crystalline, whereas AO-80 obtained by cooling from its molten state is an amorphous material. Annealing treatment below the melting point of AO-80 results in structural development. The mixture of chlorinated polyethylene (CPE) and vitrified AO-80 particles exhibits a dramatic change in the dynamic mechanical properties during heat treatment at 130℃. This change can be attributed to the decomposition of the vitrified AO-80 particles and the hybridization of two constituents. The vitrified AO-80 particles can crystallize again in a CPE matrix by annealing at 100℃, but this crystal is different from that of the initial AO-80 in its microstructure. In addition, the incorporation of CPE chains caused a dramatic increase in the modulus. As a result, the AO-80 crystal particles that contain some CPE chains act as multifunctional crosslinks and the CPE/AO-80 hybrid was found to be a new type of elastomer.     

Melt‐processable blends of ionic poly(p‐phenylene terephthalamide) and poly(4‐vinylpyridine): Relaxation behavior

Melt‐processable blends were prepared from rigid molecules of an ionically modified poly(p‐phenylene terephthalamide) (PPTA) and flexible‐coil molecules of poly(4‐vinylpyridine) (PVP). Dynamic mechanical analyses of blends with 50% or more of the ionic PPTA component revealed the presence of two distinct phases. The glass‐transition temperature of the more stable, ionic PPTA‐rich phase increased linearly with the ionic PPTA content. The second phase present in these blends was an ionic PPTA‐poor, or a PVP‐rich, phase. For this phase, a reasonably good fit of the data, showing the glass‐transition temperature as a function of the ionic PPTA content, was achieved between the results of this study and the reported results of previous investigation of molecular composites of the same two components with ionic PPTA contents of 15 wt % or less. The possible influence of annealing on the blend structure of a 90/10 blend of ionic PPTA and PVP was examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1468–1475, 2003     

TSC study of the dielectric relaxations of human‐bone collagen

Differential scanning calorimetry (DSC) and thermally stimulated current (TSC) were used to characterize human‐bone collagen. DSC glass‐transition and denaturation temperatures of the collagen in a dehydrated state were 90 and 215 °C, respectively. By TSC, the main relaxation mode, labeled α and located around 90 °C, could be attributed to the dielectric manifestation of the glass transition. The corresponding molecular movements are cooperative with a compensation temperature close to the denaturation temperature. At low temperatures and in a hydrated state, a second mode labeled β₂ was observed at −110 °C. Dehydration shifted this mode to higher temperatures, revealing a weak mode labeled γ at −150 °C. This γ mode was attributed to motions of aliphatic side chains. An analysis of low‐temperature elementary spectra allowed us to assign the β₂ mode to structural water movements and revealed an additional compensation phenomenon in the temperature range (−80 to −50 °C). Because the compensation temperature of this mode was close to the collagen glass‐transition temperature, the corresponding mode β₁ was attributed to polar side‐chain motions, precursors of a collagen glass transition. Finally, around ambient temperature, three sharp peaks were attributed to hydrogen bonds breaking. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 987–992, 2000     

Influence of nanoparticle surface chemistry on the thermomechanical and magnetic properties of ferromagnetic nanocomposites

The effect of nanoparticle surface chemistry on the thermal, mechanical, and magnetic properties of poly(methyl methacrylate) (PMMA) nanocomposites with cobalt ferrite nanofillers was studied by comparing nanofillers coated with oleic acid (OA; which does not covalently bond to the PMMA matrix) and 3‐methacryloxypropyltrimethoxysilane (MPS, which covalently bonds to the PMMA matrix). Thermogravimetric analysis revealed an increase in the thermal degradation temperature of the nanocomposites compared with the neat polymer. The effect of cobalt ferrite nanofiller on the glass transition temperature (T_g) of the nanocomposite was evaluated by differential scanning calorimetry. The T_g value of the material increased when the particles were introduced. Dynamic mechanical analysis indicated an increase in the storage modulus of the nanocomposite because of the presence of nanofiller and a shift in the peak of loss tangent toward higher temperature. Magnetic measurements indicated that both nanocomposites had a small hysteresis loop at 300 K and no hysteresis at 400 K. However, estimates of the nanofiller's rotational relaxation times and measurements of the zero field cooled temperature‐dependent magnetization indicate that the observed lack of hysteresis at 400 K is likely because of particle rotation in the polymer matrix. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Phase structure and thermomechanical properties of primary and tertiary amine‐cured epoxy/silica hybrids

Several kinds of organic–inorganic hybrids were synthesized from an epoxy resin and a silane alkoxide with a primary amine‐type curing agent or tertiary amine curing catalyst. In the hybrid systems cured with the primary amine‐type curing agent, the storage modulus in the high‐temperature region increased, and the peak area of the tan δ curve decreased. Moreover, the mechanical properties were improved by the hybridization of small amounts of the silica network. However, these phenomena were not observed in the hybrid systems cured with the tertiary amine catalyst. The differences in the network structures of the hybrid materials with the different curing processes were characterized with Fourier transform infrared (FTIR). In the hybrid systems cured with the primary amine‐type curing agent, FTIR results showed the formation of a covalent bond between silanol and hydroxyl groups that were generated by the reaction of an epoxy group with an active hydrogen of the primary amine. However, this phenomenon was not observed in the hybrids cured with the tertiary amine. The hybrids with the primary amine showed a homogeneous microstructure in transmission electron microscopy observations, although the hybrids cured with the tertiary amine showed a heterogeneous structure. These results mean that the differences in the interactions between the organic and inorganic phases significantly affect the properties and microstructures of the resultant composites. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1071–1084, 2001     

Aging and cold crystallization of melt‐extruded poly(trimethylene terephthalate) films

We analyzed the thermal crystallization, glass‐transition behavior, and mechanical properties of melt‐extruded poly(trimethylene terephthalate) (PTT) films to investigate their physical aging and annealing effects. The physical aging and annealing of PTT films had an influence on the glass‐transition temperature, recrystallization behavior, and mechanical properties. When samples were aged at an ambient temperature, the crystallization temperature decreased largely within 5 h, the heat of crystallization increased, and the breaking stress and breaking elongation increased. The glass‐transition temperature of annealed samples, which was obtained from differential scanning calorimetry and dynamic mechanical measurements, increased with increasing annealing temperature below 80 °C but decreased above that temperature. In addition, the glass‐transition temperature and modulus of annealed samples were largely affected by the annealing time; in particular, they increased sharply within 1 h on annealing at 50 °C. Consequently, the change in the glass‐transition temperature on annealing was ascribed to the fact that the molecular constraint due to recrystallization and the mobility of rigid amorphous PTT chains competed with each other, being dependent on the annealing temperature. The mechanical properties of aged samples were closely related to their cold‐crystallization behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1920–1927, 2001     

Analysis of blends of poly(styrene‐co‐acrylonitrile) with an epoxy/aromatic amine resin using scanning thermal microscopy

Using a microthermal analyzer TA Instruments 2990 μTA, we have analyzed the morphologies developed for the resin tetraglycidyl‐4,4′‐diaminodiphenylmethane cured with an aromatic amine 4,4′‐diaminodiphenylsulphone modified with different amounts of poly(styrene‐co‐acrylonitrile) (SAN) thermoplastic. The phase‐separation phenomenon induced by polymerization was also followed by scanning electron microscopy. Using the modulated local thermal‐analysis mode of μTA, the glass‐transition temperatures of different domains for each sample were evaluated. Dynamic mechanical analyzer experiments were made to evaluate the macroscopic thermal properties of the blends. A morphology was well established for all blends examined with these techniques showing a nodular structure, the epoxy‐rich phase, and a continuous phase, the SAN‐rich phase, that forms the matrix. From both microscopic and macroscopic thermal analyses, it is concluded that a phase separation exists for the blends investigated. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 284–289, 2002     

Luminescence studies of polymer matrices. III. Characterization and evaluation of acrylic acid‐based polymers as hosts for a phosphorescent coding system

The phosphorescence characteristics of naphthyl labelled poly(acrylic acid) film samples have been studied as a function of temperature, with a view to investigating the effect of matrix control on the level of triplet emission observed. Two relaxations, which serve to deactivate the excited triplet states have been detected from phosphorescence lifetime measurements: the α (or glass) and the βtransition (which can be associated with the onset of rotation of the carboxylic acid group). Investigation of the emission from 2‐benzoyl naphthalene dispersed within both an acrylic acid‐methyl methacrylate copolymer and a PAA film, respectively, has revealed that the more intense, longer‐lived phosphorescence results from the modified polymer. This is considered to reflect the existence of (i) hydrogen‐bonding interactions induced by the presence of carboxylic acid groups which serve to form a rigid matrix and (ii) intramolecular aggregates of methyl methacrylate units which create hydrophobic‐rich pockets, capable of sustaining intense phosphorescence at room temperature. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2127–2136, 1999     

Synthesis and property of phosphorus‐containing bismaleimide by a novel method

A series of novel addition products (phosphorus content: 0.5, 1, 2, and 3 wt %) were synthesized from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide (DOPO) and 4,4′‐bismaleimidodiphenylmethane (BMI). NMR and IR were used to confirm the structures of the synthetic bismaleimides. Dynamic mechanical analysis scans showed the glass‐transition temperatures of these cured BMIs decreased with phosphorus content. Thermal gravimetric analysis heating scans indicated that they had high thermal stability. Limiting oxygen index measurements implied that the flame retardancy was improved by the incorporation of DOPO. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2260–2268, 2000