维生素E与磷脂酰胆碱的单分子膜研究

测定了下列气水界面单分子膜的表面压－平均分子面积等温线：（１）ｄ－α，ｄ－β，ｄ－γ－，和ｄ－δ－生育酚等４种维生素Ｅ与ＤＰＰＣ，ＤＯＰＣ及ＤＬＰＣ的混合物，（２）ｄ－α－生育酚等摩尔比的ＤＰＰＣ和ＤＬＰＣ的混合物，（３）胆固醇与ＤＰＰＣ，ＤＬＰＣ的混合物，讨论了维生素Ｅ色满环上甲基对其在ＰＣ单分子膜中物理化作用的影响，实验结果表明：（１）维生素Ｅ以ｄ－α〉ｄ－β－≈ｄ－γ〉ｄ－δ的次序引起的ＤＰ     

Dynamic adsorption and surface tension of aqueous dilauroylphosphatidylcholine dispersions under physiological conditions

The dynamic surface tension and equilibrium adsorption behavior of DLPC dispersions in phosphate buffer saline at 37 and 25 degrees C was studied with tensiometry, infrared reflection--absorption spectroscopy (IRRAS), and ellipsometry. The results are compared with those in water (Pinazo et al. Langmuir 2002, 18, 8888). Even though the pH and salinity have no apparent effect on the equilibrium surface tension and the surface pressure--area isotherm, they affect the dynamic surface tension by decreasing the adsorption rate and increasing the dynamic tension minima at a pulsating area of 20 or 80 cycles per minute. Moreover, IRRAS and ellipsometry results show that the adsorbed layers and the spread monolayers have larger area per molecule, or looser packing, in buffer than in water. A new hypothesis is proposed to elucidate the effect of pH/salinity on this zwitterionic surfactant: there is some specific interaction or binding between the ions from the buffer saline with the polar headgroups of DLPC. This interaction induces stronger intermolecular repulsions of the surfactant layer in buffer than that in water, despite the expected electrostatic screening effect, and causes higher dynamic surface tensions. The results have implications in designing lung surfactant replacement formulations.     

Mixed Langmuir monolayers of cholesterol and `essential' fatty acids

Langmuir monolayers of cholesterol and various fatty acids, such as stearic, oleic, linoleic, α-linolenic, and arachidonic acids, spread at the air/water interface are investigated. The system of cholesterol and stearic acid is found to be immiscible, with only one collapse, occurring at the same surface pressure for all composition range. However, surface pressure (π) – area (A) isotherms of cholesterol/unsaturated fatty acids show a characteristic course with two collapse states. The pressure of the first collapse varies with the proportion of the components in the mixture, while the second collapse, occurring at the surface pressure characteristic of cholesterol alone, is independent of mole fraction of the investigated fatty acid. The application of the surface phase rule indicates that the unsaturated fatty acids/cholesterol mixtures are miscible up to the surface pressure corresponding to the first collapse. Negative values of the excess free energy of mixing in all composition ranges prove that the mixtures are stable. The interactions existing in mixtures of cholesterol and unsaturated fatty acids possessing even numbers of double bonds are strongest in the lower region of fatty acid proportion, and the results are consistent with the minimum values of the excess free energy of mixing, indicating the most stable mixtures. For cholesterol and unsaturated fatty acids with odd numbers of double bonds the behavior is different, and the strongest interactions occur in both low and high regions of mole fraction of an acid. Received: 2 May 2000 Accepted: 26 October 2000     

Alignment of liquid crystal and dichroic dye molecules in mixed Langmuir and Langmuir-Blodgett films

A study of dichroic dye-liquid crystal mixtures (guest-host systems) in monolayers formed at a gas-liquid interface (Langmuir films) and at a solid surface (Langmuir-Blodgett films) has been made. As a host 4- n -octyl-4′-cyanobiphenyl (8CB) or 4- n -pentyl-4″-cyano- p -terphenyl (5CT) were chosen, while three dichroic azo dyes with various molecular structures were used as guest species. The dyes were added to the liquid crystal matrices at a concentration corresponding to the whole range of molar fractions and the surface pressure-mean molecular area isotherms for Langmuir films were recorded. On the basis of the isotherms, conclusions about the molecular organization and the miscibility of the components in the ultrathin films were drawn. The Langmuir films were transferred onto the quartz plates at surface pressures below the collapse point. The polarized absorption spectra of the Langmuir-Blodgett films were recorded and information about the alignment and intermolecular interactions in the mixtures of the non-amphiphilic dichroic dyes and the liquid crystals with strongly polar terminal groups were obtained.     

Mixed monolayers of poly-alanine and lipids at the air-water interface

Summary The mixed monolayers of poly-alanine + stearyl alcohol and poly-alanine + cholesterol were studied at the air-water interface. In the mixed monolayers the surface pressure-area isotherms showed three collapse states. The first and the third collapse pressures were identical in magnitude with the collapse pressures of pure components. The intermediate collapse pressure in the poly-alanine + stearyl alcohol was found to be ca. 5 dyne/cm higher than that was observed in the poly-alanine + cholesterol system. Further, the mixed films in both systems were found to show no deviation from the ideality rule. The magnitude o f the intermediate collapse state is shown to be related to the van der Waals forces present in the lipid films.With 6 figures     

Alignment of liquid crystal and dichroic dye molecules in mixed Langmuir and Langmuir-Blodgett films

A study of dichroic dye-liquid crystal mixtures (guest-host systems) in monolayers formed at a gas-liquid interface (Langmuir films) and at a solid surface (Langmuir-Blodgett films) has been made. As a host 4- n -octyl-4'-cyanobiphenyl (8CB) or 4- n -pentyl-4"-cyano- p -terphenyl (5CT) were chosen, while three dichroic azo dyes with various molecular structures were used as guest species. The dyes were added to the liquid crystal matrices at a concentration corresponding to the whole range of molar fractions and the surface pressure-mean molecular area isotherms for Langmuir films were recorded. On the basis of the isotherms, conclusions about the molecular organization and the miscibility of the components in the ultrathin films were drawn. The Langmuir films were transferred onto the quartz plates at surface pressures below the collapse point. The polarized absorption spectra of the Langmuir-Blodgett films were recorded and information about the alignment and intermolecular interactions in the mixtures of the non-amphiphilic dichroic dyes and the liquid crystals with strongly polar terminal groups were obtained.     

Headgroup percolation and collapse of condensed langmuir monolayers

We present a study of Langmuir isotherms and 2D bulk moduli of binary lipid mixtures, where changes in monolayer collapse pressure (Pic) are followed while varying the relative amounts of the two components. For monolayers containing dipalmitoylphosphocholine (DPPC) with either hexadecanol (HD) or palmitic acid (PA), a distinctly non-monotonic change in Pic is observed with varying composition. At low mole fractions, there is a slight decrease in Pic as films get richer in DPPC, while a sharp increase to pure DPPC-like values is observed when the mole fraction exceeds approximately 0.7. The sudden transition in collapse pressure is explained using the principles of rigidity percolation, and important ramifications of this phenomenon for biological surfactant are discussed.     

On the interaction of dipalmitoyl phosphatidylcholine with normal long-chain alcohols in a mixed monolayer: a thermodynamic study

This study investigated the mixed monolayer behavior of dipalmitoyl phosphatidylcholine (DPPC) with normal long-chain alcohols at the air/water interface. Surface pressure–area isotherms of mixed DPPC/C₁₈OH and DPPC/C₂₀OH monolayers at 37°C were obtained and compared with previous results for the mixed DPPC/C₁₆OH system. The negative deviations from additivity of the areas and the variation of the collapse pressure with composition imply that DPPC and long-chain alcohols were miscible and formed non-ideal monolayers at the interface. At lower surface pressures, it seems that the attractive intermolecular force was dominant in molecular packing in the mixed monolayers. At higher surface pressures, the data suggest that the molecular packing in mixed DPPC/C₁₆OH monolayers may be favored by the packing efficiency or geometric accommodation. Furthermore, negative values of excess free energy of mixing were obtained and became significant as the hydrocarbon chain length of alcohols increased, which indicates there were attractive interactions between DPPC and long-chain alcohols. In each free energy of mixing–composition curve, there was only one minimum and thus a phase separation did not exist for mixed DPPC/long-chain alcohol monolayers.     

Photoinduced phase separation and miscibility in the condensed phase of a mixed Langmuir monolayer

We report our studies on the mixed Langmuir monolayer of mesogenic molecules, p-(ethoxy)-p-phenylazo phenyl hexanoate (EPPH) and octyl cyano biphenyl (8CB), employing the techniques of surface manometry and Brewster angle microscopy. Our studies show that the mixed monolayer exhibits higher collapse pressures for certain mole fractions of EPPH in 8CB as compared to individual monolayers. Also, a considerable reduction in the area per molecule is seen in the mixed monolayer, indicating a condensed phase. We have also studied the photostability of the mixed monolayer at different initial surface pressures. The mixed monolayer, under alternate cycles of UV and visible illumination, exhibits changes in surface pressures. This is due to the photoinduced transformation of EPPH isomers in the mixed monolayer. Our in-situ Brewster angle microscope studies for 0.5 mole fraction of EPPH in 8CB show a phase separation in the UV and a miscible phase in the visible, at low surface pressures ( approximately 5 mN/m). At higher surface pressures ( approximately 10 mN/m), under UV illumination, we find a phase separation which does not revert to a miscible phase under visible illumination.     

Effect of molecular surface packing on the enzymatic activity modulation of an anchored protein on phospholipid Langmuir monolayers

The catalytic activity of a glycosylphosphatidylinositol (GPI)-anchored alkaline phosphatase has been studied in Langmuir phospholipid monolayers at different surface pressures. The enzyme substrate, p-nitrophenyl phosphate, was injected into the subphase of mixed enzyme/lipid Langmuir monolayers. Its hydrolysis product was followed by monitoring the absorbance at 410 nm in situ in the monolayer subphase of the Langmuir trough. Several surface pressures, corresponding to different molecular surface densities, were attained by lateral compression of the monolayers. The morphology of the monolayers, observed by fluorescence microscopy, showed three different types of domains owing to the heterogeneous partition of the enzyme within the mixed enzyme/lipid film. The catalytic activity was modulated by the enzyme surface density, and it increased until a pressure of 18 mN/m was reached, but it decreased significantly when the equilibrium in-plane elasticity (surface compressional modulus) increased more noticeably, resulting in alterations in the interface morphology. A model for the modulation of the enzyme orientation and catalytic activity by lipid/enzyme surface morphology and enzyme surface packing at the air/liquid interface is proposed. The results might have an important impact on the comprehension of the enzymatic activity regulation of GPI-anchored proteins in biomembranes.     

Persistence of metastability after expansion of a supercompressed fluid monolayer

Fluid monolayers of 1-palmitoyl-2-oleoyl-phosphatidylcholine collapse from an air/water interface to form a three-dimensional bulk phase at the equilibrium spreading pressure (pie) of approximately 47 mN/m. This phase transition limits access to higher surface pressures under equilibrium conditions or during slow continuous compressions. We have shown previously that these films avoid collapse and become metastable when compressed on a captive bubble to surface pressures above 60 mN/m and that the metastability persists during expansion at least to pie. Here, we first documented the extent of this persistent metastability. Rates of isobaric collapse during expansion of the metastable films were up to 3 orders of magnitude slower than those during the initial compression to high surface pressures. Recovery of the ability to collapse depended on the surface pressure to which the films were expanded and how long they were held there. Films reverted after brief exposure to 20 mN/m and after 1 h at 35 mN/m. At pie, films remained capable of reaching high surface pressures during slow compressions after 65 h, although an increase in compressibility above 55 mN/m suggested somewhat increased rates of collapse. We also determined if the films remained metastable when they acquired sufficient free area to allow reinsertion of collapsed material. Faster isobaric expansion in the presence of more collapsed material and with further deviation below pie supported the existence of reinsertion. The persistence of metastability to pie shows that films with sufficient free area to allow reinsertion remain resistant to collapse. Observations that suggest heterogeneous reinsertion, however, argue that free area may be distributed heterogeneously and leave open the possibility that metastability persists because significant regions retain a restricted free area.     

Monolayer properties of mixtures of poly(n-stearyl methacrylate), poly(n-lauryl methacrylate), and their corresponding copolymers

The monolayer properties of poly(n-stearyl methacrylate), poly(n-lauryl methacrylate), and their mixtures at various ratios of the two polymers have been studied from the measurements of their surface pressure–area isotherms at air–water interface. The monolayer properties of their mixtures have been compared with those of their corresponding copolymers. The results show that the isotherms of the mixed monolayers have two break points at higher pressures than that of poly(n-lauryl methacrylate). This suggests that the mixtures may form more stable films that consist of separate phases of the two homopolymers, although each phase may contain a small amount of the other. The isotherms of the copolymer monolayers indicate a phase transition from liquid condensed to solid film between 50 segment mole % and 70% poly(n-stearyl methacrylate). The monclayer of these copolymers has properties that differ from those of the corresponding mixtures of two pure homopolymers and is more compatible than the mixtures of pure homopolymers.     

Influence of alpha-hydroxylation of glycolipids on domain formation in lipid monolayers

By means of fluorescence and scanning force microscopy (SFM), we investigated the phase behavior of lipid monolayers composed of a mixture of 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine, sphingomyelin, and cholesterol (5/2/3) with either alpha-hydroxylated or nonhydroxylated galactocerebroside. Fluorescence images of lipid monolayers at the air-water interface demonstrate that, independent of the lipid mixture, phase separation occurs at low surface pressure up to 4-6 mN m(-1), while an almost homogeneous phase is observed at larger surface pressures. However, by means of SFM of lipid monolayers transferred by the Langmuir-Blodgett technique at around 30 mN m(-1), nanometer-sized domains became discernible in those lipid mixtures that contained galactocerebroside, while, in that without a glycolipid, no such domain formation was visible. Moreover, the alpha-hydroxy group of the galactocerebroside alters the size and the total area of the domains significantly.     

NMR characterization of dilauroyl phosphatidylcholine in adsorbed monolayers at fluid interfaces studied by multiscale computations

Structural characteristics of model monolayers of dilauroyl phosphatidylcholine (1,2‐dilauroyl‐sn‐glycerol‐3‐phosphatidylcholine [DLPC]) adsorbed at the water/vapors and water/octane interfaces were studied by means of computational chemistry methods. Coarse‐grained, followed by all‐atom molecular dynamics simulations were used to obtain the monolayers equilibrium structures at room temperature at both fluid interfaces. The analysis of the polar head orientation, polar region thickness, tail lengths, and NMR order parameter revealed that the different interface composition affects only the tail lengths and their orientation with respect to the interface. At the octane/water boundary the DLPC tails are less extended than the tails at the water/vacuum interface and are rather significantly tilted or multiply folded. Very similar structuring of the polar DLPC region at both studied boundaries was established. Dynamic ¹³C NMR chemical shift values, δ(¹³C) computed with density functional theory allowed to identify the interface effect on the DLPC molecular structure and the intramolecular motions in the adsorbed monolayer at the room temperature equilibrium. Detailed analysis of these dynamic δ(¹³C) values compared with available experimental data and static δ(¹³C) estimates of one DLPC low‐energy conformer are presented and discussed.     

Blends of amphiphilic trisilanolisobutyl-POSS and phosphine oxide substituted poly(dimethylsiloxane) at the air/water interface

Mixtures of a polyhedral oligomeric silsesquioxane, trisilanolisobutyl-POSS, and a polar silicone, poly(dimethyl-co-methylvinyl-co-methyl, 2-diphenyl phosphine oxide ethyl) siloxane (PDMS-PO), spread as Langmuir monolayers at the air/water interface are used to examine the surface phase behavior and aggregation of trisilanolisobutyl-POSS as a function of silicone composition. Analyses of the surface pressure-area per monomer (Pi-A) isotherms in terms of the collapse pressures and excess Gibbs free energies of mixing indicate the monolayers form slightly negative deviation mixtures. Direct observations of surface morphology with Brewster angle microscopy in the collapsed regime reveal that the governing factor for aggregation is the collapse Pi of the component with a stronger affinity for water. In trisilanolisobutyl-POSS/PDMS-PO blends, POSS aggregates as discrete domains and does not coalesce into larger aggregates or networklike structures for <80 wt % POSS, a feature that is vastly different from a previous study of POSS blended with regular poly(dimethylsiloxane).     

Interactions of a fungistatic antibiotic, griseofulvin, with phospholipid monolayers used as models of biological membranes

Griseofulvin (GF) is an oral antibiotic for widely occurring superficial mycosis in man and animals caused by dermaphyte fungi; it is also used in agriculture as a fungicide. The mechanism of the biological activity of GF is poorly understood. Here, the interactions of griseofulvin with lipid membranes were studied using 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC), 1,2-dilauroyl-sn-glycero-3-phosphocholine (DLPC), and 1,2-myristoyl-sn-glycero-3-phosphoethanolamine (DMPE) monolayers spread at the air/water interface. Surface pressure (Pi), electric surface potential (Delta V), grazing incidence X-ray diffraction (GIXD), and Brewster angle microscopy (BAM) were used for studying pure phospholipid monolayers spread on GF aqueous solutions, as well as mixed phospholipid/GF monolayers spread on pure water subphase. Moreover, phospholipase A2 (PLA2) activity toward DLPC monolayers and molecular modeling of the GF surface and lipophilic properties were used to get more insight into the mechanisms of GF-membrane interactions. The results obtained show that GF has a meaningful impact on the film properties; we propose that nonpolar interactions are by and large responsible for GF retention in the monolayers. The modification of membrane properties can be detected using both physicochemical and enzymatic methods. The results obtained may be relevant for elaborating GF preparations with increased bioavailability.     

Mixed monolayers of polyvinylpyridine and low-molecular-weight substances

Studies were carried out at the water/air interface on mixed monolayers of a macromolecular substance with ionizable polar groups and a “horizontal” interface orientation, poly-2-vinylpyridine, and three lowmolecular-weight substances with a “vertical” orientation, stearic acid, methyl stearate and stearylamine, at 15°, 25° and 35 °C. The surface areas, collapse pressures and compressibility coefficients as a function of mole ratios showed compatibility between the components for all three twocomponent systems. The values of the enthalpy and entropy contributions to the free surface energy of mixing were found to be positive for the poly-2-vinylpyridine/stearic acid system and negative for the other two systems.     

A combined vibrational sum frequency generation spectroscopy and atomic force microscopy study of sphingomyelin-cholesterol monolayers

A combination of vibrational sum frequency generation spectroscopy and atomic force microscopy is used to study the changes in morphology and conformational order in monolayers prepared from three natural sphingomyelin (SM) mixtures as a function of surface pressure and cholesterol concentration. The most homogeneous SM gave monolayers with well-ordered acyl chains and few gauche defects with relatively small effects of either increasing surface pressure or cholesterol addition. Heterogeneous SM mixtures with a mixture of acyl chain lengths or with significant fractions of unsaturated acyl chains had much larger contributions from gauche defects at low surface pressure and gave increasingly well-ordered monolayers as the surface pressure increased. They also showed substantial increases in lipid chain order after cholesterol addition. Overall, these results are consistent with the strong hydrogen bonding capacity of SM leading to well-ordered monolayers over a range of surface pressures. The changes in acyl chain order for natural SMs as a function of cholesterol are relevant to formation of sphingolipid-cholesterol enriched domains in cell membranes.     

水溶性菁染料与类脂物混合单分子膜中J-聚集体形成的研究

报道了具有相同发色团,并有不同电荷的二种菁染料单分子膜中J-聚集体的形成。测定了单分子膜的π/A,△V/A曲线,反射光谱及吸收光谱。从实验结果得出:带正电荷的染料与花生酸混合形成单分子膜后,膜中染料的二聚体与J-聚集体随着表面压力改变存在着一个平衡。而带负电荷的染料与二十烷基胺成膜后,即使在很低的表面压下也有J-聚集体形成。同时染料分子在水面上的取向是各向异性。     

Model of peripheral protein adsorption to the water/lipid interface

Two models have been developed to describe the adsorption of a model peripheral protein, colipase, to phospholipid/diacylglycerol (PL/DG) monolayers. One model is applicable at monolayer collapse pressure and at any composition that exceeds the DG mole fraction of PL/DG lateral complexes (Sugár, I. P.; Mizuno, N. K.; Momsen, M. M.; Brockman, H. L. Biophys. J. 2001, 81, 3387-3397). The other model is applicable at any lateral pressure but only below the mole fraction of DG in the complex (Sugár, I. P.; Mizuno, N. K.; Brockman, H. L. Biophys. J. 2005, 89, 3997-4005). Both models assume that initiation of colipase adsorption to the water/lipid interface requires an area of water-exposed hydrophobic surface that exceeds a critical value. In the first model, accessible surface is provided by the head groups of the uncomplexed DG molecules. This surface area follows a binomial distribution. In the second model, accessible area is created by hydrocarbon chains becoming exposed at the water/lipid interface as total lipid packing density of monolayers of PL and/or PL/DG complexes is decreased. This surface area follows a Poisson distribution. The model described in this paper is a unification, extension, and improvement of these models that is applicable at any lateral pressure and any PL/DG mole fraction. Calculated normalized initial colipase adsorption rates are compared with the available experimental values, and predictions of the adsorption rates are made for currently unmeasured compositions and lateral pressure regimes.