Branching by reactive end groups. III. Synthesis,branching, and analysis of m‐ethynylphenol/p‐t‐butylphenol‐coterminated bisphenol a polycarbonates

The use of m‐ethynylphenol (m‐EP) and p‐t‐butylphenol (PTBP) as coterminators for bisphenol A polycarbonates (BA PCs) provided long‐chain‐branched PCs, partially crosslinked PCs, or both after the thermal reaction of the terminal m‐EP groups, depending on the molar ratio of the chain terminators. Linear m‐EP/PTBP PCs were prepared by solution phosgenation of BA and the two coterminators. Differential scanning calorimetry showed the onset of the m‐EP‐end‐group reaction at about 250 °C by the appearance of a reaction exotherm. The enthalpy (ΔH) of this reaction was roughly proportional to the amount of m‐EP in the PC and to an extent could be used to monitor the progress of the reaction and estimate its kinetics. A complete m‐EP‐end‐group reaction was evident from gel permeation chromatography analysis upon heating under N₂ to 380 °C for 10 min or 360 °C for 60 min. The amount, if any, of gel formed after the m‐EP‐end‐group reaction depended on X_EP; those PCs with a X_EP value less than or equal to 0.33 had little or no gel. The maximum X_EP that precluded the formation of gels after branching was estimated to be about 0.45–0.48. The molecular weight of m‐EP/PTBP PCs increased after branching, as evidenced by gel permeation chromatography analysis. Assuming that the terminal m‐EP groups had a statistical distribution on the polymer chain ends and that they underwent only homopolymerization, the average reacted m‐EP‐group functionality according to estimated gel‐point composition was about 2.8–3.0. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2352–2358, 2000     

Randomly branched bisphenol A polycarbonates. I. Molecular weight distribution modeling,interfacial synthesis,and characterization

Randomly branched bisphenol A polycarbonates (PCs) were prepared by interfacial polymerization methods to explore the limits of gel‐free compositions available by the adjustment of various composition and process variables. A molecular weight distribution (MWD) model was devised to predict the MWD, G, and weight‐average molecular weight per arm (M_w /arm) values based on the composition variables. The amounts of the monomer, branching agent, and chain terminator must be adjusted such that the weight‐average functionality of the phenolic monomers (F_OH ) was less than 2 to preclude gel formation in both the long‐ and short‐chain branched (SCB) PCs. Several series of SCB and long‐chain branched PCs were prepared, and those lacking gels showed molecular weights measured by gel permeation chromatography–UV and gel permeation chromatography–LS consistent with model calculations. In SCB PCs, the minimum M_w /arm that could be realized without gel formation depended on both composition (molecular weight, terminator type) and process (terminator addition point, coupling catalyst) variables. The minimum M_w /arm achieved in the low molecular weight series studied ranged from ∼3300 to ∼1000. The use of long chain alkyl phenol terminators gave branched PCs with lower glass‐transition temperatures but a higher gel‐free minimum M_w /arm. SCB PCs where M_w /arm was less than ∼M_c spontaneously cracked after compression molding, a result attributed to their lack of polymer chain entanglements. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 560–570, 2000     

Acrylic acid level and adhesive performance and peel master‐curves of acrylic pressure‐sensitive adhesives

Three series of pressure‐sensitive adhesives were prepared with constant glass‐transition temperature, using emulsion polymerization. The monomers chosen were butyl acrylate, 2‐ethylhexyl acrylate (EHA), methyl methacrylate (MMA), and acrylic acid (AA). Within each polymer series, the proportion of AA monomer was held constant for each polymer preparation but acrylic ester monomer levels were varied. Adhesion performance was assessed by measurement of loop tack, static shear resistance, and through the construction of peel master‐curves. Peel master‐curves were generated through peel tests conducted over a range of temperatures and peel rates and through application of the time–temperature superposition principle. Bulk effects dominated by polymer zero shear viscosity change as AA and EHA levels were varied were attributed to the observed effect on static shear resistance and the horizontal displacements of peel master‐curves. Static shear resistance was found to strongly correlate with log(a_C), a parameter introduced to horizontally shift peel master‐curves to form a superposed, “super master‐curve”. An interfacial interaction was proposed to account for deviations observed when loop tack was correlated with log(a_C). Surface rearrangements via hydrogen bonding with the test substrate were suggested as responsible for the interfacial interaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1237–1252, 2006     

Surface mechanical properties of low‐molecular‐weight polystyrene below its glass‐transition temperatures

Lap shear and friction force measurements were carried out on a series of monodisperse polystyrene (PS) films below the corresponding glass‐transition temperatures. It showed that adhesion between the PS/PS interface was possible at the temperature below the bulk T_g, and the lower the molecular weight of PS, the lower the temperature at which the interfacial strength was detectable. The examination of a series of molecular weights indicated both the surface molecular motion and the magnitude of the interfacial strength were dependent on molecular weight and its distribution. And a steep increase of the friction force with increasing the test temperature was observed around 0 ∼ 30 °C. The contact angle of water versus molecular weight measurements also showed a transition at room temperature. The behavior observed in this study was supposed to be due to the increased molecular mobility, and was in good agreement with the measured surface transition temperatures by DSC. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 654–658, 2000     

Suppressing the long‐chain branching in the synthesis of poly(styrene‐b‐butyl acrylate‐b‐styrene) in RAFT emulsion polymerization by tuning the interfacial properties

Reversible addition‐fragmentation chain transfer (RAFT) emulsion polymerization is becoming an important technique to synthesize the latex of block copolymers. A previous study showed that in the synthesis of polystyrene‐b‐poly(butyl acrylate)‐b‐polystyrene triblock copolymer via RAFT emulsion polymerization using amphiphilic oligo(acrylic acid‐styrene) macroRAFT as surfactant and mediator, the molecular weight distribution could be much broadened to PDI higher than 2. In this study, an in‐depth investigation was performed to decrease PDI. It was found that long‐chain branches could be formed in the synthesis of triblock block copolymer, leading to the appearance of a higher molecular weight shoulder in the GPC curve of the final product. The lower neutralization degree of acrylic acid (AA) units on the macroRAFT and shorter AA chains would help to suppress the formation the long‐chain branches, leading to PDI around 1.5. It is evidenced that the successful suppression is due to the promotion of radical entry as a result of decreased interfacial transport impedance. It is also evidenced that the presence of styrene during the polymerization of butyl acrylate could promote the formation of long chain branches. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1464–1473     

Synthesis of novel hyperbranched poly(ester‐amide)s based on neutral α‐amino acids via “AD + CBB′” couple‐monomer approach

A series of novel hyperbranched poly(ester‐amide)s (HBPEAs) based on neutral α‐amino acids have been synthesized via the “AD + CBB′” couple‐monomer approach. The ABB′ intermediates were stoichiometrically formed through thio‐Michael addition reaction because of reactivity differences between functional groups. Without any purification, in situ self‐polycondensations of the intermediates at elevated temperature in the presence of a catalyst afforded HBPEAs with multihydroxyl end groups. The degrees of branching (DBs) of the HBPEAs were estimated to be 0.40–0.58 and 0.24–0.54 by quantitative ¹³C NMR with two different calculation methods, respectively, depending on polymerization conditions and structure of monomers. The influences of catalyst, temperature, and intermediate structure on the polymerization process and molecular weights as well as properties of the resultant polymers were investigated. FTIR, NMR, and DEPT‐135 NMR analyses revealed the branched structure of the resultant polymers. The HBPEAs possess moderately high molecular weights with broad distributions, glass transition temperatures in the range of ?25.5 to 36.5 °C, and decomposition temperatures at 10% weight loss under nitrogen and air in the regions of 243.4–289.1 °C and 231.4–265.6 °C, respectively. Among them, those derived from D ,L ‐phenylalanine display the lowest degree of branching, whereas the highest glass transition temperature and the best thermal stability. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and thermochemistry of phenylmaleimide- and phenylnadimide-terminated bisphenol A polycarbonates

Phenylmaleimide (PMI)- and phenylnadimide (PNI)-terminated bisphenol A polycarbonates (PCs) were prepared by solution or interfacial phosgenation processes, and their thermal crosslinking, both with and without a free radical initiator, and the thermal stability of the resultant network polymers were investigated. m-PMI PCs were prepared by interfacial phosgenation of bisphenol A and m-hydroxyphenylmaleimide, but p-hydroxyphenylmaleimide caused rapid phosgene hydrolysis under interfacial conditions and PCs from it could only be made by solution phosgenation. The degree of crosslinking of PMI PCs, as measured by their gel fraction, heated in the absence of a free radical initiator was generally higher at 250°C than at 300°C and increased with the concentration of PMI end groups. m- and p-PMI PCs form thermosets having nearly complete gel fractions by radical initiated curing at 150–200°C. The gel fraction of these thermosets decreases with exposure to higher temperatures (300°C). This behavior is attributed to BA PC chain degradation induced by nitrogen-containing maleimide reaction products. p-PNI PC was prepared by solution phosgenation and the thermal reaction of it in the presence of the initiator produced only a small increase in molecular weight. © 1997 John Wiley & Sons, Inc.     

Synthesis and characterization of block copolymers from 2‐vinylnaphthalene by anionic polymerization

The anionic polymerization of 2‐vinylnaphthalene (2VN) has been studied in tetrahydrofuran (THF) at ?78 °C and in toluene at 40 °C. 2VN polymerization in THF, toluene, or toluene/THF (99:1 v/v) initiated by sec‐butyllithium (sBuLi) indicates living characteristics, affording polymers with predefined molecular weights and narrow molecular weight distributions. Block copolymers of 2VN with methyl methacrylate (MMA) and tert‐butyl acrylate (tBA) have been synthesized successfully by sequential monomer addition in THF at ?78 °C initiated by an adduct of sBuLi–LiCl. The crossover propagation from poly(2‐vinylnaphthyllithium) (P2VN) macroanions to MMA and tBA appears to be living, the molecular weight and composition can be predicted, and the molecular weight distribution of the resulting block copolymer is narrow (weight‐average molecular/number‐average molecular weight < 1.3). Block copolymers with different chain lengths for the P2VN segment can easily be prepared by variations in the monomer ratios. The block copolymerization of 2VN with hexamethylcyclotrisiloxane also results in a block copolymer of P2VN and poly(dimethylsiloxane) (PDMS) contaminated with a significant amount of homo‐PDMS. Poly(2VN‐b‐nBA) (where nBA is n‐butyl acrylate) has also been prepared by the transesterification reaction of the poly(2VN‐b‐tBA) block copolymer. Size exclusion chromatography, Fourier transform infrared, and ¹H NMR measurements indicate that the resulting polymers have the required architecture. The corresponding amphiphilic block copolymer of poly(2VN‐b‐AA) (where AA is acrylic acid) has been synthesized by acidic hydrolysis of the ester group of tert‐butyl from the poly(2VN‐b‐tBA) copolymer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4387–4397, 2002     

Thermal and spectral stability of electroluminescent hyperbranched copolymers containing tetraphenylthiophene‐quinoline‐triphenylamine moieties

Fluorescent hyperbranched copolymers (HB‐x, x = 1–4) with inherent tetraphenylthiophene, triphenylamine (TPA) and quinoline (Qu) moieties were prepared to study the influence of the TPA branching point on the thermal and the spectral stability. All the HB‐x copolymers exhibited high glass transition temperatures (T_gs = 245–315 °C) with the detected values increasing with the increasing branching TPA content in the HB‐x. The solid HB‐x films possess high emission efficiency with the resulting quantum yields (?_Fs) in the ranges of 0.72–0.74. More importantly, the HB‐x copolymers and the derived light‐emitting devices exhibit high photoluminescence (PL) and electroluminescence (EL) stability towards thermal annealing at temperatures higher than 200 °C. After annealing at 200 °C (or 300 °C), no change was observed in the respective PL and EL spectra of HB‐1 (or HB‐4) copolymers. The spectral stability was found to correlate with T_g and with the highest branching density, HB‐4 copolymer possesses the highest thermal stability among all HB‐xs and show no EL spectral change after annealing at 300 °C for 4 h. The results indicate that all the branched HB‐x copolymers are promising candidates for the polymer light‐emitting diodes due to their high quantum yield and spectral stability. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

From the N‐Heterocyclic Carbene‐Catalyzed Conjugate Addition of Alcohols to the Controlled Polymerization of (Meth)acrylates

Among various N‐heterocyclic carbenes (NHCs) tested, only 1,3‐bis(tert‐butyl)imidazol‐2‐ylidene (NHC^tBu) proved to selectively promote the catalytic conjugate addition of alcohols onto (meth)acrylate substrates. This rather rare example of NHC‐catalyzed 1,4‐addition of alcohols was investigated as a simple means to trigger the polymerization of both methyl methacrylate and methyl acrylate (MMA and MA, respectively). Well‐defined α‐alkoxy poly(methyl (meth)acrylate) (PM(M)A) chains, the molar masses of which could be controlled by the initial [(meth)acrylate]₀/[ROH]₀ molar ratio, were ultimately obtained in N,N‐dimethylformamide at 25 °C. A hydroxyl‐terminated poly(ethylene oxide) (PEO‐OH) macro‐initiator was also employed to directly access PEO‐b‐PMMA amphiphilic block copolymers. Investigations into the reaction mechanism by DFT calculations revealed the occurrence of two competitive concerted pathways, involving either the activation of the alcohol or that of the monomer by NHC^tBu.     

Preparation and characterization of fluorine‐containing aromatic condensation polymers. VII. Aromatic polyacetals and copolyacetals from 2,2‐bis(4‐hydroxyphenyl)‐1,1,1,3,3,3‐hexafluoropropane and/or 2,2‐bis(4‐hydroxyphenyl)propane and 2‐(trifluoromethyl)benzal chloride

A series of fluorine‐containing aromatic homopolyacetals and copolyacetals with a wide range of unit ratios were synthesized by the solution polycondensation of 2,2‐bis(4‐hydroxyphenyl)‐1,1,1,3,3,3‐hexafluoropropane (bisphenol AF), 2,2‐bis(4‐hydroxyphenyl)propane (bisphenol A), or both with 2‐(trifluoromethyl)benzal chloride, and the effect of fluorine substitution on the properties of these polymers is discussed in relation to the fluorine contents. High molecular weight polyacetals with reduced viscosities of 0.43–0.97 dL/g were obtained in high yields with potassium hydroxide as a base, 18‐crown 6‐ether as a catalyst, and N‐methyl‐2‐pyrrolidinone as a medium at 100 °C for 3 h. Regardless of the fluorine contents, these polymers all were highly soluble in various solvents, including benzene, chloroform, ethyl acetate, and tetrahydrofuran, and afforded colorless, transparent, and tough films by solution casting. The temperatures of 5% weight loss and 10% weight loss under nitrogen both increased significantly and monotonously with increasing fluorine content, whereas the glass‐transition temperatures were scarcely affected by fluorine substitution. The dielectric constant at 1 MHz of the bisphenol AF‐based homopolyacetal was 2.43, which was remarkably lower than the value of the bisphenol A‐based homopolyacetal, 2.68. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1873–1879, 2000     

Stimulus‐responsive polymers based on 2‐hydroxypropyl acrylate prepared by RAFT polymerization

Homopolymerization and diblock copolymerization of 2‐hydroxypropyl acrylate (HPA) has been conducted using reversible addition fragmentation chain transfer (RAFT) chemistry in tert‐butanol at 80 °C. PHPA homopolymers were obtained with high conversions and narrow molecular weight distributions over a wide range of target degrees of polymerization. Like its poly(2‐hydroxyethyl methacrylate) isomer, PHPA homopolymer exhibits inverse temperature solubility in dilute aqueous solution, with cloud points increasing systematically on lowering the mean chain length. The nature of the end groups is shown to significantly affect the cloud point, whereas no effect of concentration was observed over the PHPA concentration range investigated. Various thermoresponsive PHPA‐based diblock copolymers were prepared via one‐pot syntheses in which the second block was either permanently hydrophilic or pH‐responsive. Preliminary studies confirmed that poly(ethylene oxide)‐poly(2‐hydroxypropyl acrylate) (PEO₄₅‐PHPA₄₈) and poly(2‐hydroxypropyl acrylate)‐ poly(2‐hydroxyethyl acrylate) (PHPA₄₉‐PHEA₆₈)diblock copolymers formed well‐defined PHPA‐core micelles in 10 mM sodium nitrate solution at 40 °C and 70 °C with mean hydrodynamic diameters of 20 nm and 35 nm, respectively. In contrast, most other PHPA‐based diblock copolymers investigated formed larger colloidal aggregates in 10 mM NaNO₃ solution at elevated temperatures. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2032–2043, 2010     

Synthesis,characterization, and bulk properties of amphiphilic copolymers containing fluorinated methacrylates from sequential copper‐mediated radical polymerization

The partly fluorinated monomers, 2,2,2‐trifluoroethyl methacrylate (3FM), 2,2,3,3,4,4,5,5‐octafluoropentyl methacrylate (8FM), and 1,1,2,2‐tetrahydroperfluorodecyl methacrylate (17FM) have been used in the preparation of block copolymers with methyl methacrylate (MMA), 2‐methoxyethyl acrylate (MEA), and poly(ethylene glycol) methyl ether methacrylate (PEGMA) by Atom Transfer Radical Polymerization. A kinetic study of the 3FM homopolymerization initiated with ethyl bromoisobutyrate and Cu(I)Br/N‐(n‐propyl)‐2‐pyridylmethanimine reveals a living/controlled polymerization in the range 80–110 °C, with apparent rate constants of 1.6 · 10⁻⁴ s⁻¹ to 2.9 · 10⁻⁴ s⁻¹. Various 3FM containing block copolymers with MMA are prepared by sequential monomer addition or from a PMMA macroinitiator in all cases with controlled characteristics. Block copolymers of 3FM and PEGMA resulted in block copolymers with PDI < 1.22, whereas block copolymers from 3FM and MEA have less controlled characteristics. The block copolymers based on MMA with 8FM and 17 FM have PDI's < 1.30. The glass transition temperatures of the block copolymers are dominated by the majority monomer, as the sequential monomer addition results in too short pure blocks to induce observable microphase separation. The thermal stability of the fluorinated poly((meth)acrylate)s in inert atmosphere is less than that of corresponding nonfluorinated poly((meth)acrylate)s. The presence of fluorinated blocks significantly increases the advancing water contact angle of thin films compared to films of the nonfluorinated poly((meth)acrylate)s. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8097–8111, 2008     

Synthesis of poly(o‐cresol) by oxidative coupling polymerization of o‐cresol

The oxidative coupling polymerization of o‐cresol was investigated using various 2‐substituted pyridine/CuCl catalysts under an oxygen atmosphere, in which 2‐phenylpyridine/CuCl and 2‐(p‐tolyl)pyridine/CuCl catalysts yielded poly(o‐cresol)s with higher regioselectivity for 1,4‐coupling. These polymerizations produced branched and crosslinked polymers in the later stages of polymerization. These polymers showed good thermal properties, such as 5% weight loss temperatures of up to 406 °C and glass transition temperatures of up to 151 °C. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 878–884     

Reversible addition–fragmentation chain transfer polymerization of 2‐naphthyl acrylate with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate as a chain‐transfer agent

The reversible addition–fragmentation chain transfer (RAFT) polymerizations of 2‐naphthyl acrylate (2NA) initiated by 2,2′‐azobisisobutyronitrile were investigated with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN) as a RAFT agent at various temperatures in a benzene solution. The results of the polymerizations showed that 2NA could be polymerized in a controlled way by RAFT polymerization with CPDN as a RAFT agent; the polymerization rate was first‐order with respect to the monomer concentration, and the molecular weight increased linearly with the monomer conversion. The polydispersities of the polymer were relatively low up to high conversions in all cases. The chain‐extension reactions of poly(2‐naphthyl acrylate) (P2NA) with methyl methacrylate and styrene successfully yielded poly(2‐naphthyl acrylate)‐b‐poly(methyl methacrylate) and poly(2‐naphthyl acrylate)‐b‐polystyrene block polymers, respectively, with narrow polydispersities. The P2NA obtained by RAFT polymerization had a strong ultraviolet absorption at 270 nm, and the molecular weights had no apparent effect on the ultraviolet absorption intensities; however, the fluorescence intensity of P2NA increased as the molecular weight increased and was higher than that of 2NA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2632–2642, 2005     

Atom transfer radical polymerization of n‐butyl acrylate catalyzed by CuBr/N‐(n‐hexyl)‐2‐pyridylmethanimine

The homogeneous atom transfer radical polymerization (ATRP) of n‐butyl acrylate with CuBr/N‐(n‐hexyl)‐2‐pyridylmethanimine as a catalyst and ethyl 2‐bromoisobutyrate as an initiator was investigated. The kinetic plots of ln([M]₀/[M]) versus the reaction time for the ATRP systems in different solvents such as toluene, anisole, N,N‐dimethylformamide, and 1‐butanol were linear throughout the reactions, and the experimental molecular weights increased linearly with increasing monomer conversion and were very close to the theoretical values. These, together with the relatively narrow molecular weight distributions (polydispersity index ～ 1.40 in most cases with monomer conversion > 50%), indicated that the polymerization was living and controlled. Toluene appeared to be the best solvent for the studied ATRP system in terms of the polymerization rate and molecular weight distribution among the solvents used. The polymerization showed zero order with respect to both the initiator and the catalyst, probably because of the presence of a self‐regulation process at the beginning of the reaction. The reaction temperature had a positive effect on the polymerization rate, and the optimum reaction temperature was found to be 100 °C. An apparent enthalpy of activation of 81.2 kJ/mol was determined for the ATRP of n‐butyl acrylate, corresponding to an enthalpy of equilibrium of 63.6 kJ/mol. An apparent enthalpy of activation of 52.8 kJ/mol was also obtained for the ATRP of methyl methacrylate under similar reaction conditions. Moreover, the CuBr/N‐(n‐hexyl)‐2‐pyridylmethanimine‐based system was proven to be applicable to living block copolymerization and living random copolymerization of n‐butyl acrylate with methyl methacrylate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3549–3561, 2002     

Combination of nitroxide‐mediated polymerization and SET‐LRP for the synthesis of high molar mass branched and star‐branched poly(n‐butyl acrylate) characterized by size exclusion chromatography and rheology

Branched and star‐branched polymers were successfully synthesized by the combination of two successive controlled radical polymerization methods. A series of linear and star poly(n‐butyl acrylate)‐co‐poly(2‐(2‐bromoisobutyryloxy) ethyl acrylate) statistical copolymers, P(nBA‐co‐BIEA)_x, were first synthesized by nitroxide‐mediated polymerization (NMP at T > 100 °C). The subsequent polymerization of n‐butyl acrylate by single electron transfer‐living radical polymerization (SET‐LRP at T = 25 °C), initiated from the brominated sites of the P(nBA‐co‐BIEA)_x copolymer, produced branched or star‐branched poly(n‐butyl acrylate) (PnBA). Both types of polymerizations (NMP and SET‐LRP) exhibited features of a controlled polymerization with linear evolutions of logarithmic conversion versus time and number‐average molar masses versus conversion for final M_n superior to 80,000 g mol^?1. The branched and star‐branched architectures with high molar mass and low number of branches were fully characterized by size exclusion chromatography. The Mark–Houwink Sakurada relationship and the analysis of the contraction factor (g′ = ([η]_branched/[η]_linear)_M) confirmed the elaboration of complex PnBA. The zero‐shear viscosities of the linear, star‐shaped, branched, and star‐branched polymers were compared. The modeling of the rheological properties confirmed the synthesis of the branched architectures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and swelling behavior of amphiphilic comb‐like branched polymer (AA‐co‐CMS)‐g‐PMMA

Copolymerization of acrylic acid and p‐chloromethylstyrene (p‐CMS) in dioxane initiated with α,α′‐azobisisobutyronitrile was carried out to produce macroinitiator P(AA‐co‐CMS) containing PhCH₂Cl group at 65°C. Then methyl methacrylate was grafted onto P(AA‐co‐CMS) backbone using PhCH₂Cl group as an initiation site and FeCl₂/triphenyl phosphine complex as a catalyst. The resulted copolymer (AA‐co‐CMS)‐g‐PMMA with a comb‐like branched structure has a hydrophilic backbone (PAA) and hydrophobic side chains (PMMA). Compositions and structures of macroinitiator and the grafted product of P(AA‐co‐CMS)‐g‐PMMA were determined by ¹H‐NMR, infrared (IR), and gel permeation chromatography (GPC). The average graft number, the average length of branch chains, the graft ratio, and the graft efficiency were investigated. The swelling behavior of the comb‐like branched polymer was also investigated. The gradual increase of swelling ratios was accompanied by an increase of pH and temperature. The kinetic exponents indicated that the swelling transport mechanisms transformed from Fickian diffusion to non‐Fickian transport as the decreasing pH. Copyright © 2009 John Wiley & Sons, Ltd.     

Ring‐opening copolymerization of ethylene carbonate and ε‐caprolactone catalyzed by neodymium tris(2,6‐di‐tert‐butyl‐4‐methylphenolate): Synthesis,characterization, and dynamic mechanic analysis

The ring‐opening copolymerization of ethylene carbonate (EC) with ε‐caprolactone (CL) was carried out using neodymium tris(2,6‐di‐tert‐butyl‐4‐methylphenolate) as a single‐component catalyst. Copolymers containing up to 22.0% EC contents with high molecular weights (up to 23.97 × 10⁴) and moderate molecular weight distributions (between 1.66 and 2.03) were synthesized at room temperature. Compared with homopoly(ε‐caprolactone), the copolymers with EC units exhibited increased glass transition temperatures (?35.6 °C), reduced melting temperatures (44.5 °C), and greatly enhanced elongation percentage at break (2383%) based on dynamic mechanic analysis. The crystallinities of the copolymers decreased with the increasing EC molar percentage in the products. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4050–4055, 2008     

Semi‐Crystalline Polar Polyethylene: Ester‐Functionalized Linear Polyolefins Enabled by a Functional‐Group‐Tolerant,Cationic Nickel Catalyst

A dibenzobarrelene‐bridged, α‐diimine Ni^II catalyst (rac‐ 3 ) was synthesized and shown to have exceptional behavior for the polymerization of ethylene. The catalyst afforded high molecular weight polyethylenes with narrow dispersities and degrees of branching much lower than those made by related α‐diimine nickel catalysts. Catalyst rac‐ 3 demonstrated living behavior at room temperature, produced linear polyethylene (T_m=135 °C) at −20 °C, and, most importantly, was able to copolymerize ethylene with the biorenewable polar monomer methyl 10‐undecenoate to yield highly linear ester‐functionalized polyethylene.