Studies on poly(ε‐caprolactone)/thiodiphenol blends: The specific interaction and the thermal and dynamic mechanical properties

The effects of several low molecular weight compounds with hydroxyl groups on the physical properties of poly(ε‐caprolactone) (PCL) were investigated by Fourier transform infrared (FTIR) spectroscopy and high‐resolution solid‐state ¹³C NMR. PCL and 4,4′‐thiodiphenol (TDP) interact through strong intermolecular hydrogen bonds and form hydrogen‐bonded networks in the blends at an appropriate TDP content. The thermal and dynamic mechanical properties of PCL/TDP blends were investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis, respectively. The melting point of PCL decreased, whereas both the glass‐transition temperature and the loss tangent tan δ of the blend increased with an increase in TDP content. The addition of 40 wt % TDP changed PCL from a semicrystalline polymer in the pure state to a fully amorphous elastomer. The molecules of TDP lost their crystallizability in the blends with TDP contents not greater than 40 wt %. In addition to TDP, three other PCL blend systems with low molecular weight additives containing two hydroxyl groups, 1,4‐dihydroxybenzene, 1,4‐di‐(2‐hydroxyethoxy) benzene, and 1,6‐hexanediol, were also investigated with FTIR and DSC, and the effects of the chemical structure of the additives on the morphology and thermal properties are discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1848–1859, 2000     

Electrospun fiber mats of poly(3‐hydroxybutyrate), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate), and their blends

Electrospinning of poly(3‐hydroxybutyrate) (PHB), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV), and their blends was first carried out in chloroform at 50 °C on a stationary collector. The average diameter of the as‐spun fiber from PHB and PHBV solutions decreased with increasing collection distance and increased with increasing solution concentration and applied electrical potential. In all of the spinning conditions investigated, the average diameter of the as‐spun pure fibers ranged between 1.6 and 8.8 μm. Electrospinning of PHB, PHBV, and their blends was carried out further at a fixed solution concentration of 14% w/v on a homemade rotating cylindrical collector. Well‐aligned, cross‐sectionally round fibers without beads were obtained. The average diameter of the as‐spun pure and blend fibers ranged between 2.3 and 4.0 μm. The as‐spun fiber mats appeared to be more hydrophobic than the corresponding films and much improvement in the tensile strength and the elongation at break was observed for the blend fiber mats over those of the pure fiber ones. Lastly, indirect cytotoxicity evaluation of the as‐spun pure and blend fiber mats with mouse fibroblasts (L929) indicated that these mats posed no threat to the cells. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2923–2933, 2006     

Preparation and physical properties of poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) films

To prepare thermally stable and high‐performance polymeric films, new solvent‐soluble aromatic polyamides with a carbamoyl pendant group, namely poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) (p‐PDCBTA) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) (m‐PDCBTA), were synthesized. The polymers were cyclized at around 200 to 350 °C to form quinazolone and benzoxazinone units along the polymer backbone. The decomposition onset temperatures of the cyclized m‐ and p‐PDCBTAs were 457 and 524 °C, respectively, lower than that of poly(p‐phenylene terephthalamide) (566 °C). For the p‐PDCBTA film drawn by 40% and heat‐treated, the tensile strength and Young's modulus were 421 MPa and 16.4 GPa, respectively. The film cyclized at 350 °C showed a storage modulus (E′) of 1 × 10¹¹ dyne/cm² (10 GPa) over the temperature range of room temperature to 400 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 775–780, 2000     

Two‐dimensional Fourier transform infrared spectroscopy study of biosynthesized poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐ co‐hydroxyvalerate)

Generalized two‐dimensional (2D) Fourier transform infrared correlation spectroscopy was used to investigate the effect of the comonomer compositions on the crystallization behavior of two types of biosynthesized random copolymers, poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐co‐hydroxyvalerate). The carbonyl absorption band around 1730 cm^?1 was sensitive to the degree of crystallinity. 2D correlation analysis demonstrated that the 3‐hydroxyhexanoate units preferred to remain in the amorphous phase of the semicrystalline poly(hydroxybutyrate‐co‐hydroxyhexanoate) copolymer, resulting in decreases in the degree of crystallinity and the rate of the crystallization process. The poly(hydroxybutyrate‐co‐hydroxyvalerate) copolymer maintained a high degree of crystallinity when the 3‐hydroxyvalerate fraction was increased from 0 to 25 mol % because of isodimorphism. The crystalline and amorphous absorption bands for the carbonyl bond for this copolymer, therefore, changed simultaneously. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 649–656, 2002; DOI 10.1002/polb.10126     

Influence of multiple processing on selected properties of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)

The effect of multiple (up to 10 times) injection molding of processed poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P(3,4HB)) on its phase transition temperatures, degree of crystallinity, degradation temperature, mass flow rate, mechanical properties, dynamic mechanical properties, and Charpy's impact strength is presented. The studies have shown that the multiple injection lowers the degree of crystallinity and the thermal stability of P(3,4HB). The mass flow rate values increased with increasing the injection number. It was found that the multiple injections had no substantial effect on the tensile strength up to 10 injection cycles and the tensile strength at break, tensile strain at tensile strength, and tensile strain at break up to 6 injection cycles. The maximum value of storage modulus at 30 °C and impact strength were recorded for sample after 4 cycles of injection, while the values of storage modulus at 120 °C increased with increase of the injection cycles. Copyright © 2015 John Wiley & Sons, Ltd.     

Antibacterial poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) fibrous membranes containing quaternary ammonium salts

In this study, antimicrobial membranes based on biodegradable material poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐4HB)] and quaternary ammonium salts (QASs) by two methods have been performed. Three QASs with varied alkyl chain lengths have been synthesized successfully and characterized by ¹H nuclear magnetic resonance and Fourier transform infrared. The synthesized QASs were blended with P(3HB‐4HB) and electrospun into composite fibrous membranes or casted into conventional membranes. Electrospun fibrous membranes with large surface areas are a superior type of antimicrobial biomaterials, and they exhibit preferable properties than solution casting membranes. Specifically, electrospun fibrous membranes are tougher and can inactivate both Gram‐positive Staphylococcus aureus and Gram‐negative Escherichia coli O157:H7 in a contact time of 30 min, whereas the solution casting membranes cannot. The length of alkyl chain in the quaternary ammonium groups on the modified P(3HB‐4HB) membranes is able to influence the antimicrobial activity. This type of antimicrobial material may have potential applications in biomaterial field. Copyright © 2016 John Wiley & Sons, Ltd.     

Compatibility and thermal properties of poly(3‐hydroxybutyrate)/poly(glycidyl methacrylate) blends

Poly(3‐hydroxybutyrate) (PHB)/poly(glycidyl methacrylate) (PGMA) blends were prepared by a solution‐precipitation procedure. The compatibility and thermal decomposition behavior of the PHB/PGMA blends was studied with differential scanning calorimetry, thermogravimetric analysis, and differential thermal analysis (DTA). The blends were immiscible in the as‐blended state, but for the blends with PGMA contents of 50 wt % or more, the compatibility was dramatically changed after 1 min of annealing at 200 °C. In addition, PHB/PGMA blends showed higher thermal stability, as measured by maximum decomposition temperatures and residual weight during thermal degradation. This was probably due to crosslinking reactions of the epoxide groups in the PGMA component with the carboxyl chain ends of PHB fragments during the degradation process, and the occurrence of such reactions can be assigned to the exothermic peaks in the DTA thermograms. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 351–358, 2002     

Studies on Binary Blends of Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) and Natural Polyphenol Catechin: Specific Interactions and Thermal Properties

The existence of a specific intermolecular hydrogen‐bonding interaction between poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(3HB‐co‐3HH)] and (+)‐catechin in their blends was demonstrated by Fourier‐transform infrared spectroscopy (FT‐IR). It was found that the experimentally estimated fraction of hydrogen‐bonded carbonyl groups was much lower than the theoretically predicted maximum fraction. Only one glass transition temperature (T_g) occurred in the blends with the compositions detected by differential scanning calorimetry (DSC), being further confirmed by the results of dynamic mechanical thermal analysis (DMTA). The decrease of the melting point (T_m) and the increase of the glass transition temperature of the blends observed by the DSC measurements also suggested the existence of a strong intermolecular interaction. It was interesting to note that, as a low‐molecular‐weight compound, catechin showed a glass transition, which arises from strong self‐association. As expected, the crystalline structure of P(3HB‐co‐3HH) in the blends showed no change, but the crystallinity of the copolymer component in the blends, calculated by wide‐angle X‐ray diffraction, decreased with the increase of catechin weight content. Investigated by tensile experiments, the maximum strength and modulus decreased sharply with the increase of catechin content; on the contrary, the elongation changed slowly.

The FT‐IR spectra in the wave‐number 1 680–1 780 cm^?1 region for blends of P(3HB‐co‐3HH)/catechin. A: HBH; B: HBHC10; C: HBHC20; D: HBHC30; E: HBHC40; F: HBHC50; and G: catechin.     

Thermal behavior and intermolecular interactions in blends of poly(3‐hydroxybutyrate) and maleated poly(3‐hydroxybutyrate) with chitosan

The thermal behavior and intermolecular interactions of blends of poly(3‐hydroxybutyrate) (PHB) and maleated PHB with chitosan were studied with differential scanning calorimetry, Fourier transform infrared (FTIR), wide‐angle X‐ray diffraction (WAXD), and X‐ray photoelectron spectroscopy (XPS). The differences in the two blend systems with respect to their thermal behavior and intermolecular interactions were investigated. The melting temperatures, melting enthalpies, and crystallinities of the two blend systems gradually decreased as the chitosan content in the blends increased. Compared with that of the PHB component with the same composition, the crystallization of the maleated PHB component was more intensively suppressed by the chitosan component in the blends because of the rigid chitosan molecular chains and the intermolecular hydrogen bonds between the components. FTIR, WAXD, and XPS showed that the intermolecular hydrogen bonds in the blends were caused by the carbonyls of PHB or maleated PHB and chitosan aminos, and their existence depended on the compositions of the blends. The introduction of maleic anhydride groups onto PHB chains promoted intermolecular interactions between the maleated PHB and chitosan components. In addition, the intermolecular interactions disturbed the original crystal structures of the PHB, maleated PHB, and chitosan components; this was further proven by WAXD results. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 35–47, 2005     

Thermal and infrared spectroscopic studies on hydrogen‐bonding interactions between poly‐(ε‐caprolactone) and some dihydric phenols

The effects of three dihydric phenols on the thermal properties of poly‐(ε‐caprolactone) (PCL) were investigated by DSC. The thermal properties of PCL were found to be greatly modified by the addition of 4,4′‐dihydroxydiphenyl ether (DHDPE). When the content of DHDPE reached 40%, PCL that was a semicrystalline polymer in the pure state changed to a fully amorphous elastomer. Fourier transform infrared (FTIR) spectroscopy was also applied to investigate the specific interaction between PCL and DHDPE. The formations of intermolecular hydrogen bonds between the carbonyl groups of PCL and the hydroxyl groups of DHDPE were discovered. By applying the Beer–Lambert law and a curve‐fitting program, the fractions of hydrogen‐bonded carbonyl groups were quantitatively analyzed. Although one DHDPE molecule had the potentiality to form two hydrogen bonds with PCL chains, the values of the fraction of the hydroxyl group involved in the intermolecular hydrogen bond were so little that from a statistical point of view, the formation of two hydrogen bonds was very difficult for every DHDPE molecule. Both DSC and FTIR revealed that 4,4′‐dihydroxydiphenyl methane and 4,4′‐dihydroxyphenyl had the ability to form hydrogen bonds with PCL, which were strongly affected by the polarity of the group linking two hydroxyphenyls and the flexibility of the molecular chain. The stronger the polarity of the group and the better the flexibility of molecular chain, the more tendencies dihydric phenol had to form intermolecular hydrogen bonds with PCL. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2108–2117, 2001     

Nonisothermal crystallization kinetics of poly(ε‐caprolactone) blocks in double crystalline triblock copolymers containing poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) and poly(ε‐caprolactone) units

The poly(3‐hydroxbutyrate‐co‐3‐hydroxyvalerate)/poly(ε‐caprolactone) block copolymers (PHCLs) with three different weight ratios of PCL blocks (38%, named PHCL‐38; 53%, named PHCL‐53; and 60%, named PHCL‐60) were synthesized by using PHBV with two hydroxyl end groups to initiate ring‐opening polymerization of ε‐caprolactone. During DSC cooling process, melt crystallization of PHCL‐53 at relatively high cooling rates (9, 12, and 15 °C min^?1) and PHCL‐60 at all the selected cooling rates corresponded to PCL blocks so that PHCL‐53 and PHCL‐60 were used to study the nonisothermal crystallization behaviors of PCL blocks. The kinetics of PCL blocks in PHCL‐53 and PHCL‐60 under nonisothermal crystallization conditions were analyzed by Mo equation. Mo equation was successful in describing the nonisothermal crystallization kinetics of PCL blocks in PHCLs. Crystallization activation energy were estimated using Kissinger's method. The results of kinetic parameters showed that both blocks crystallized more difficultly than corresponding homopolymers. With the increase of PCL content, the crystallization rate of PCL block increased gradually. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Thermal degradation kinetics of biodegradable poly(3‐hydroxybutyrate)/layered double hydroxide nanocomposites

The thermal degradation behaviors of biodegradable poly(3‐hydroxybutyrate) (PHB) and PHB/poly(ethylene glycol) phosphonates (PEOPAs)‐modified layered double hydroxide (PMLDH) nanocomposites have been investigated using thermogravimetric analysis. Effects of PMLDH contents on the isothermal degradation kinetics of PHB were explored. These experimental results show that the degradation kinetics of PHB/PMLDH nanocomposites is the chain‐scission process of cyclic β‐elimination reaction with the following autocatalytic reactions, which is very similar to that of pure PHB matrix. Further calculated data based on the autocatalytic model can fit very well with the experimental data. The E_a value of PHB/PMLDH nanocomposites is increased as the content of PMLDH increases. This can be attributed to the incorporation of more PMLDH loading to PHB induced a decrease in the degradation rate and an increase in the residual weight for PHB/PMLDH nanocomposites. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1207–1213, 2008     

Synthesis and characterization of poly(β‐hydroxybutyrate) and poly(ϵ‐caprolactone) copolyester by transesterification

To synthesize the copolyester of poly(β‐hydroxybutyrate) (PHB) and poly(?‐caprolactone) (PCL), the transesterification of PHB and PCL was carried out in the liquid phase with stannous octoate as the catalyzer. The effects of reaction conditions on the transesterification, including catalyzer concentration, reaction temperature, and reaction time, were investigated. The results showed that both rising reaction temperature and increasing reaction time were advantageous to the transesterification. The sequence distribution, thermal behavior, and thermal stability of the copolyesters were investigated by ¹³C NMR, Fourier transform infrared spectroscopy, differential scanning calorimetry, wide‐angle X‐ray diffraction, optical microscopy, and thermogravimetric analysis. The transesterification of PHB and PCL was confirmed to produce the block copolymers. With an increasing PCL content in the copolyesters, the thermal behavior of the copolyesters changed evidently. However, the introduction of PCL segments into PHB chains did not affect its crystalline structure. Moreover, thermal stability of the copolyesters was little improved in air as compared with that of pure PHB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1893–1903, 2002     

Compatibilizing effect of a graft copolymer on bacterial poly(3‐hydroxybutyrate)/poly(methyl methacrylate) blends

Blends of isotactic (natural) poly(3‐hydroxybutyrate) (PHB) and poly(methyl methacrylate) (PMMA) are partially miscible, and PHB in excess of 20 wt % segregates as a partially crystalline pure phase. Copolymers containing atactic PHB chains grafted onto a PMMA backbone are used to compatibilize phase‐separated PHB/PMMA blends. Two poly(methyl methacrylate‐g‐hydroxybutyrate) [P(MMA‐g‐HB)] copolymers with different grafting densities and the same length of the grafted chain have been investigated. The copolymer with higher grafting density, containing 67 mol % hydroxybutyrate units, has a beneficial effect on the mechanical properties of PHB/PMMA blends with 30–50% PHB content, which show a remarkable increase in ductility. The main effect of copolymer addition is the inhibition of PHB crystallization. No compatibilizing effect on PHB/PMMA blends with PHB contents higher than 50% is observed with various amounts of P(MMA‐g‐HB) copolymer. In these blends, the graft copolymer is not able to prevent PHB crystallization, and the ternary PHB/PMMA/P(MMA‐g‐HB) blends remain crystalline and brittle. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1390–1399, 2002     

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate)–Poly(vinyl‐acetate) blends

Nonisothermal crystallization and melting behavior of poly(β‐hydroxybutyrate) (PHB)–poly(vinyl acetate) (PVAc) blends from the melt were investigated by differential scanning calorimetry using various cooling rates. The results show that crystallization of PHB from the melt in the PHB–PVAc blends depends greatly upon cooling rates and blend compositions. For a given composition, the crystallization process begins at higher temperatures when slower scanning rates are used. At a given cooling rate, the presence of PVAc reduces the overall PHB crystallization rate. The Avrami analysis modified by Jeziorny and a new method were used to describe the nonisothermal crystallization process of PHB–PVAc blends very well. The double‐melting phenomenon is found to be caused by crystallization during heating in DSC. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 443–450, 1999     

Miscibility,crystallization kinetics,and morphology of poly(β‐hydroxybutyrate) and poly(methyl acrylate) blends

The miscibility, spherulite growth kinetics, and morphology of binary blends of poly(β‐hydroxybutyrate) (PHB) and poly(methyl acrylate) (PMA) were studied with differential scanning calorimetry, optical microscopy, and small‐angle X‐ray scattering (SAXS). As the PMA content increases in the blends, the glass‐transition temperature and cold‐crystallization temperature increase, but the melting point decreases. The interaction parameter between PHB and PMA, obtained from an analysis of the equilibrium‐melting‐point depression, is −0.074. The presence of an amorphous PMA component results in a reduction in the rate of spherulite growth of PHB. The radial growth rates of spherulites were analyzed with the Lauritzen–Hoffman model. The spherulites of PHB were volume‐filled, indicating the inclusion of PMA within the spherulites. The long period obtained from SAXS increases with increased PMA content, implying that the amorphous PMA is entrapped in the interlamellar region of PHB during the crystallization process of PHB. All the results presented show that PHB and PMA are miscible in the melt. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1860–1867, 2000     

A zinc(II) metal–organic framework with a novel topology formed from 4,4′,4′′‐nitrilotribenzoate and 4,4′‐bipyridine ligands

A metal–organic framework with a novel topology, poly[sesqui(μ₂‐4,4′‐bipyridine)bis(dimethylformamide)bis(μ₄‐4,4′,4′′‐nitrilotribenzoato)trizinc(II)], [Zn₃(C₂₁H₁₂NO₆)₂(C₁₀H₈N₂)_1.5(C₃H₇NO)₂]_n, was obtained by the solvothermal method using 4,4′,4′′‐nitrilotribenzoic acid and 4,4′‐bipyridine (bipy). The structure, determined by single‐crystal X‐ray diffraction analysis, possesses three kinds of crystallographically independent Zn^II cations, as well as binuclear Zn₂(COO)₄(bipy)₂ paddle‐wheel clusters, and can be reduced to a novel topology of a (3,3,6)‐connected 3‐nodal net, with the Schläfli symbol {5.6²}₄{5².6}₄{5⁸.8⁷} according to the topological analysis.     

Phase Behavior and Thermal Properties for Binary Blends of Bacterial Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s with Narrow‐Comonomer‐Unit Compositional Distribution

The miscibility and the effect of compositional distribution on physical properties were investigated for binary blends of biosynthesized poly(3‐hydroxybutyrate) [P(3HB)] and comonomer compositionally fractionated poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)s [P(3HB‐co‐3HH)] with narrow compositional distribution. Biosynthesized P(3HB‐co‐3HH) samples were compositionally fractionated using solvent (chloroform)/nonsolvent (n‐heptane) mixtures. The binary blends of fractionated P(3HB‐co‐3HH)s with different 3HH unit content were prepared by casting from solution in chloroform. The miscibility and the thermal properties of these blends were analyzed by differential scanning calorimetry (DSC). It was found that the two components are miscible in the amorphous phase when the difference in 3HH unit content between the two component polymers of these blends is less than 20 mol‐%, subsequently they are immiscible when the difference is larger than 30 mol‐%. By comparing the thermal properties of the binary blends of fractions, with those for the fractions themselves, and with those for the bacterially as‐produced unfractionated copolyesters, the effects of compositional distribution on the properties of copolyesters were discussed.

Glass transition temperatures of blends PHB/H10, H10/H20, and PHB/H20 versus total 3HH unit content in the blends. The solid lines are the best fits of the experimental results of the P(3HB‐co‐3HH) fractions with narrow compositional distribution.     

Hydrogen bonding interaction and crystallization behavior of poly (butylene succinate‐co‐butylene adipate)/thiodiphenol complexes

The poly (butylene succinate‐co‐butylene adipate) (PBSA)/thiodiphenol (TDP) complexes were prepared by melt blending. Intermolecular hydrogen bonding between carbonyl group of PBSA and hydroxyl group of TDP formed as verified by a combination FTIR and peak fitting technique. As a result, the crystallization temperature, melting temperature, crystallinity and crystallization rate of PBSA decreased with addition of TDP, implying impeded crystallization and reduced lamellar thickness. On the basis of Lauritzen–Hoffman analysis, the fold surface energy (σ_e) and work of chain folding (q) were increased by TDP incorporation. POM observation exhibited concentric ring‐banded spherulites for samples with 10 and 20 wt% TDP. A peculiar ring‐banded pattern with discrepant band spacing was obtained for the first time by addition of 30 wt% TDP, whose formation mechanism remains to be discussed. Copyright © 2016 John Wiley & Sons, Ltd.