Melt‐state polymer chain dimensions as a function of temperature

The unperturbed chain dimensions (〈R²〉_o/M) of cis/trans‐1,4‐polyisoprene, a near‐atactic poly(methyl methacrylate), and atactic polyolefins were measured as a function of temperature in the melt state via small‐angle neutron scattering (SANS). The polyolefinic materials were derived from polydienes or polystyrene via hydrogenation or deuteration and represent structures not encountered commercially. The parent polymers were prepared via lithium‐based anionic polymerizations in cyclohexane with, in some cases, a polymer microstructure modifier present. The polyolefins retained the near‐monodisperse molecular weight distributions exhibited by the precursor materials. The melt SANS‐based chain dimension data allowed the evaluation of the temperature coefficients [dln 〈R²〉_o/dT(κ)] for these polymers. The evaluated polymers obeyed the packing length (p)‐based expressions of the plateau modulus, G = kT/np³ (MPa), and the entanglement molecular weight, M_e = ρN_anp³ (g mol^?1), where n_t denotes the number (～21) of entanglement strands in a cube with the dimensions of the reptation tube diameter (d_t) and ρ is the chain density. The product np³ is the displaced volume (V_e) of an entanglement that is also expressible as pd or kT/G. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1768–1776, 2002     

Nonlinear rheology of highly entangled polymer solutions in start‐up and steady shear flow

Orientation angle and stress‐relaxation dynamics of entangled polystyrene (PS)/diethyl phthalate solutions were investigated in steady and step shear flows. Concentrated (19 vol %) solutions of 0.995, 1.81, and 3.84 million molecular weight (MW) PS and a semidilute (6.4 vol %) solution of 20.6 million MW PS were used to study the effects of entanglement loss on dynamics. A phase‐modulated flow birefringence apparatus was developed to facilitate measurements of time‐dependent changes in optical equivalents of shear stress (n₁₂ ≈ Cσ) and first normal stress differences (n₁ = n₁₁ ? n₂₂ ≈ CN₁) in a planar‐Couette shear‐flow geometry. Flow birefringence results were supplemented with cone‐and‐plate mechanical rheometry measurements to extend the range of shear rates over which entangled polymer dynamics are studied. In slow (τ > ) steady shear‐flow experiments using the ultrahigh MW polymer sample (20.6 × 10⁶ MW PS), steady‐state n₁₂ and n₁ results manifest unusual power‐law dependencies on shear rate [n_12,ss ～ ^0.4 and n_1,ss ～ ^0.8]. At shear rates in the range τ < < τ, steady‐state orientation angles χ_SS are found to be nearly independent of shear rate for all but the most weakly entangled materials investigated. For solutions containing the highest MW PS, an approximate plateau orientation angle χ_p in the range 20–24° is observed; χ_p values ranging from 14 to 16° are found for the other materials. In the start‐up of fast steady shear flow (γ˙ ≥ τ), transient undershoots in orientation angle are also reported. The molecular origins of these observations were examined with the help of a tube model theory that accommodates changes in polymer entanglement density during flow. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2275–2289, 2001     

Solid‐state nuclear magnetic resonance relaxation times in crosslinked macroporous polymer particles of divinylbenzene homopolymers

Monodisperse porous particles of poly(divinylbenzene) prepared by the activated swelling method have been investigated by solid‐state ¹³C crosspolarization magic‐angle spinning (CPMAS) nuclear magnetic resonance (NMR) relaxation measurements. Homopolymeric combinations of two porogens (toluene and 2‐ethylhexanoic acid) and two monomers (meta‐ and para‐divinylbenzene) were studied. Residual vinyl groups were systematically reacted with increasing amounts of bromine, producing 20 different polymers samples for which we measured crosspolarization times, T_CH, proton rotating frame spin‐lattice relaxation, T, ¹³C spin‐lattice relaxation, T, and proton spin‐lattice relaxation, T. These parameters were chosen to reflect expected changes in a wide range of frequencies of motion as a function of structure. Relative differences in the molecular mobility of the major functional groups (aromatic, vinyl and aliphatic) is related to initial reactants used, vinyl concentration, relative reactivity of vinyl groups, distribution of vinyl groups, pore structure, and degree of crosslinking. Variable temperature ¹H combined rotation and multiple pulse NMR (CRAMPS) was used to derive activation energies for selected samples via measurement of the proton spin‐lattice relaxation time, T. Irreversible thermal effects were observed in ambient temperature relaxation after heating to temperatures in the range of 393–418 K. Simple univariate statistical analyses failed to reveal consistent correlations among the known variables. However, the application of more sophisticated multivariate and neural network analyses allowed excellent structure–property predictions to be made from the relaxation time data. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1307–1328, 1999     

Entanglement friction and dynamics in blends of starlike and linear polymer molecules

We investigate relaxation dynamics in a series of six‐arm star/linear 1,4‐polybutadiene blends with mechanical rheometry measurements. Blend systems are formulated to systematically probe constraint release and arm relaxation dynamics. Zero shear viscosity and terminal relaxation times of star/linear polymer blends with fixed star arm molecular weights (M_a) and compositions (?_S) are found to follow nonmonotonic dependencies on the linear polymer molecular weight (M_L). At low values of ?_S, at least two scaling regimes are apparent from the data (ξ₀ ～ M and ξ₀ ～ M), where ξ₀ refers to the zero shear viscosity or terminal relaxation time of the blend. The two regimes are separated by a critical linear polymer molecular weight M^* that is more than 20 times larger than the critical molecular weight for entanglements. When the linear polymer contribution to blend properties is removed, a clear transition from dilution dynamics, ξ₀ ～ M, to Rouse‐like constraint‐release dynamics, ξ₀ ～ M, is apparent at low values of ?_S. At higher ?_S values, a new activated constraint‐release dynamic regime is evident in which ξ₀ ～ M and ξ₀ ～ ?, where α changes continuously from approximately 2 to 0.5 as ?_S increases and β varies from 2.0 to 1.0 as M_L increases. The experimental results are compared with theoretical predictions based on a drag coupling model for entangled polymer liquids. All features observed experimentally are captured by this model, including the value of M^* for the transition from dilution to Rouse constraint‐release dynamics. Predictions of the drag coupling model are also compared with published data for the zero shear viscosity and terminal relaxation time in bidisperse linear polymer blends and pure entangled starlike molecules. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2501–2518, 2001     

A Flory–Huggins thermodynamic approach for predicting sorption equilibrium in ternary polymer systems

The Flory–Huggins theory as modified by Pouchlý has been applied to calculate preferential (λ) and total (Y) sorption coefficients for a ternary polymer system. The ternary interaction function (?₁?₂?₃G_T(u₁, ?₃)) is described as the product of three independent binary functions. This expression allows prediction of λ and Y from binary interaction parameters χ, χ, g, g, and g₁₂(?₁₀). Three ternary polymer systems are used to check the validity of the expression. Moreover for polymer systems in which the parameters g and/or g are unknown, a procedure to evaluate them has been developed and verified on systems for which sufficient experimental information is available.     

Spin probe mobility in relation to free volume and relaxation dynamics of glass‐formers: A series of spin probes in poly(isobutylene)

We present the dynamics of a series of three paramagnetic molecules of different volume, mass, and shape in amorphous glass‐forming polymer poly(isobutylene) (PIB) as investigated by means of electron spin resonance (ESR) technique. The reorientation behavior of spin probes is related to the ortho‐positronium (o‐Ps) annihilation in PIB from positron annihilation lifetime spectroscopy (PALS) and the extracted free volume information. It is also related to the dynamic data of PIB from broadband dielectric spectroscopy (BDS), neutron scattering (NS), and nuclear magnetic resonance (NMR) spectroscopy from literature. In the case of the smallest spin probe, 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO), a discontinuous course of the spectral parameter 2A_zz′ versus T dependence was observed and the subsequent phenomenological model‐free analyses of the spectral parameter, 2A_zz′ versus T, as well as of the correlation time, τ_c, versus 1/T plots provided the characteristic ESR temperatures ( , T_50G, ) and (T, T, T). These characteristic ESR temperatures were found to be consistent with the characteristic PALS temperatures: T, T = T from temperature dependences of the mean o‐Ps lifetime, τ₃, or the width of o‐Ps lifetime distribution, σ₃, respectively. In addition, the relationships between the spin probe size, V, and the free volume hole size distributions g_n(V_h) at the characteristic ESR temperatures indicate the significant influence of the free volume fluctuation at the crossover from slow to rapid regime as well as within the rapid motional regime. On the other hand, the two larger spin probes exhibit a rather continuous 2A_zz′–T plots with the respective T_50G's lying in the vicinity of T independently of their volume, mass and shape, suggesting the common origin of underlying process controlling this T_50G transition. Finally, these mutual PALS and ESR findings were compared with the known dynamic behavior of PIB which suggest that the dynamics of the TEMPO and the larger spin probes are related to free volume fluctuation associated with primary α ‐ and secondary β processes, respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1058–1068, 2009     

Factors affecting the complexation of polyacrylic acid with uranyl ions in aqueous solutions: A luminescence study

A study was carried out in aqueous solutions using luminescence technique to investigate the effects of pH, salt concentration, and temperature on the polyacrylic acid/uranyl ion (PAA/UO) complex formation as well as competitive phenomena of enhancement and quenching effects on photoexcited state of uranyl ions. It was found that excess of H⁺ and OH^? is not favorable for complexation between uranyl ions and polymer. Added nitrate salts of Na⁺ and K⁺ had significant enhancement effect on emission spectra of PAA/UO complex. These results indicated that the metal ion/polymer chain complex collapsed by addition of salts and then complex became more compact with consequent phase separation. No significant effect of temperature on the PAA/UO complex stability has been observed between 25–50 °C. The quenching rate constants obtained from Stern–Volmer plots were found to be in the order of k_q(H⁺) >> k_q(K⁺) > k_q(Na⁺). © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2737–2744, 2005     

The equilibrium melting points of random ethylene‐octene copolymers: A test of the Flory and Sanchez–Eby theories

Ethylene/l‐octene copolymers produced with metallocene catalysts are believed to have a homogeneous comonomer content with respect to molecular weight. Two series of copolymers of different molecular weights with a 1‐octene content ranging from 0 to 39 branches per 1000 carbon atoms were studied. The influence of branch content on structure and melting behavior as well as on isothermal and nonisothermal bulk crystallization was studied. In this article, the equilibrium melting temperatures of ethylene/l‐octene random copolymers is the focus. The principal techniques used were thermal analysis and small‐angle X‐ray scattering. The use of Hoffman–Weeks plots to obtain the equilibrium melting temperatures of ethylene/l‐octene random copolymers resulted in nonsensical high values of the equilibrium melting point or showed behavior parallel to the T_m = T_c line, resulting in no intercept and, hence, an infinite equilibrium melting point. The equilibrium melting temperatures of linear polyethylenes and homogeneous ethylene/l‐octene random copolymers were determined as a function of molecular weight and branch content via Thompson–Gibbs plots involving lamellar thickness data obtained from small‐angle X‐ray scattering. This systematic study made possible the evaluation of two equilibrium melting temperature depression equations for olefin‐type random copolymers, the Flory equation and the Sanchez–Eby equation, as a function of defect content and molecular weight. The range over which the two equations could be applied depended on the defect content after correction for the effect of molecular weight on the equilibrium melting temperature. The equilibrium melting temperature, T(n, p_B), of the ethylene/l‐octene random copolymers was a function of the molecular weight and defect content for low defect contents (p_B ≤ 1.0%). T(n, p_B) was a weak function of molecular weight and a strong function of the defect content at a high defect content (p_B ≥ 1.0%). The Flory copolymer equation could predict T(n, p_B) at p_B ≤ 1.0% when corrections for the effect of molecular weight were made. The Sanchez–Eby uniform inclusion model could predict T(n, p_B) at a high defect content (1.6% ≤ p_B ≤ 2.0%). We conclude that some defects were included in the crystalline phase and that the excess free energies (18–37 kJ/mol) estimated in this study were within the theoretical range. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 154–170, 2000     

Intrinsic birefringence of poly(trimethylene terephthalate)

Highly oriented poly(trimethylene terephthalate) (PTT) fiber has a low birefringence that is unexpected for an aromatic polyester with a high refractive index. To explain this observation, the intrinsic birefringence Δn of PTT crystal was calculated from its bond polarizabilities to be 0.029. This Δn is almost an order of magnitude smaller than poly(ethylene terephthalate)'s value at 0.22, although both polymers have nearly identical crystal refractive indices. The small Δn is due to the arrangement of PTT's methylene groups in gauche conformations, causing the chain‐repeating unit to be tilted ～53° away from the c axis toward the basal plane. Because of the small Δn, the crystalline‐phase orientation made only a small contribution to the overall birefringence despite the fiber's high crystallinity and orientation. To understand the effect of the number of methylene groups on polyester optical anisotropy, the Δn's of a series of poly(m‐alkylene terephthalates) with m = 2–5 were compared and correlated with ψ: an angle made by the normal of the benzene ring with the crystal's axis. As ψ′ decreases, Δn of the polyesters diminishes. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1513–1520, 2002     

Structural analysis of aggregates formed by a thermoresponsive homopolymer in dilute aqueous solutions

The aqueous solution of a thermoresponsive polymer, poly[2‐(2‐ethoxy) ethoxyethyl vinyl ether] poly(EOEOVE), contains a tiny amount of large polymer aggregates at low polymer concentrations far below the lower critical solution temperature (～40 °C). The molar mass M_w,slow, radius of gyration 〈S²〉, and hydrodynamic radius R_H,slow of the aggregating component of poly(EOEOVE) were obtained by simultaneous static and dynamic light scattering as functions of the polymer concentration and temperature, while the weight fraction w_slow of the component was estimated by size‐exclusion chromatography. The M_w,slow dependencies of 〈S²〉 and R_H,slow, as well as the ratio 〈S²〉/R_H,slow, indicated that the poly(EOEOVE) aggregate takes a sparsely branched polymer‐like conformation. We have analyzed the structure of the aggregate, using the branched polymer model of random type. The M_w,slow dependence of 〈S²〉 obtained was favorably compared with this model with reasonable structural parameters. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1179–1187, 2006     

A fourier-transform infrared spectroscopic study of the surface hydrolysis of polythiazyl

The hydrolysis of (SN)_x, in air at room temperature and 90% relative humidity has been studied using the attenuated total reflectance (ATR) method. Decomposition gave rise to strong bands at 3210 and 3150 cm^–1 [v₃ and v₁ (NH)], 1420 cm^–1 (v_b NH), 1220 cm^–1 (S?O), 1089 and 610 cm^–1 [v₁ and v₃ (SO)]. For the first 3 days, the decay of the 808 and 690 cm^–1 bands of (SN)_x was first order, with a half life of about 30 h. The spectroscopic data were consistent with the rapid formation of ? SO₂? NH₂ and ?S?NH chain end groups with subsequent relatively slow hydrolysis to (NH₄)₂SO₄, sulfur, and fresh hydrolysable chain ends.     

Preparation of exfoliated polyacrylic clay nanocomposites with high loading: An investigation into the intercalation of ammonium‐terminated polyacrylic acid and polyacrylates

Low‐molecular‐weight polyacrylic acid with amine chain end used as a macromolecular intercalating agent was synthesized by radical polymerization using 2‐aminoethanethiol hydrochloride as chain transfer agent. Three polyacrylates (sodium polyacrylate‐t‐NH, calcium polyacrylate‐t‐NH, and zinc polyacrylate‐t‐NH) were prepared by neutralization from this polyacrylic acid using sodium hydroxide, zinc oxide, and calcium hydroxide as alkalies. The intercalation of ammonium‐terminated polyacrylic acid and polyacrylate was investigated by viscosity measurement, XRD, and TEM. Using this ammonium‐terminated polyacrylic acid as the intercalating agent, exfoliated polyacrylic acid/clay and polyacrylate/clay composites with a clay loading of ～30 and 20 wt %, respectively, were prepared through the evaporation of solvent from their clay suspensions. The thermal degradation of polyacrylic acid/clay and polyacrylate/clay composites was also studied by TGA. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2335–2340, 2008     

New simple method of measuring the surface glass transition temperature of polymers

A lap‐shear joint mechanical testing method has been probed to measure the surface glass transition temperature (T) of the thick bulk films of high‐molecular‐weight polymers. As T, the temperature transition “occurrence of autoadhesion–nonoccurrence of autoadhesion” has been proposed. The influence of chain flexibility, of molecular architecture, of polymer morphology, and of chain ends concentration on the T has been investigated. The correlation between the reduction in T with respect to the glass transition temperature of the bulk (T) and the intensity of the intermolecular interaction in the polymer bulk in amorphous polymers has been found. The effect of surface roughness on T has been discussed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 2012–2021, 2010     

Functionalization of an ethylene–propylene copolymer with allyl(3‐isocyanate‐4‐tolyl) carbamate

An ethylene–propylene copolymer (EPM) was functionalized with an iso cyanate‐bearing unsaturated monomer, allyl(3‐isocyanate‐4‐tolyl) carbamate (TAI), with dicumyl peroxide as an initiator in a xylene solution. Fourier transform infrared (FTIR) was used to confirm the formation of EPM‐g‐TAI. The peak at 2273 cm^?1, characteristic of ? NCO groups in EPM‐g‐TAI, revealed evidence of grafting. The grafting degree was determined with both chemical titration and FTIR. The grafting degree could be adjusted, and the maximum was over 6 wt % without any gelation. The molar mass distribution of EPM‐g‐TAI was narrower than that of EPM. The rheological behavior of both EPM‐g‐TAI and EPM was investigated with a rotational rheometer. The apparent viscosity of EPM‐g‐TAI was higher than that of EPM and increased with an increasing grafting degree of TAI. Surface analysis by contact‐angle measurements showed that contact angles of EPM‐g‐TAI samples to a given polar liquid decreased with an increasing grafting degree of TAI. We also obtained the dispersion component of the surface free energy (γ), the polar component of the surface free energy (γ), and the total surface free energy (γ_S = γ + γ) of the grafted EPM. These parameters increased with the enhancement of the grafting degree, which gave us a quantitative estimation of the polar contribution of the grafted TAI to the total surface free energy of EPM‐g‐TAI. The adhesive property of EPM‐g‐TAI with aluminum foil was studied. The peeling strength between EPM‐g‐TAI plate and aluminum foil increased dramatically with an increasing content of grafted TAI in EPM‐g‐TAI. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 387–402, 2003     

Determination of molecular weight and its distribution of rigid‐rod polymers determined by phase‐modulated flow birefringence technique

The phase‐modulated flow birefringence (PMFB) method is widely accepted as one of the most sensitive and accurate techniques suitable for experimental tests on the molecular theory of polymer solutions. The objective of this study is to develop a systematic method to determine molecular weight and distribution of rigid‐rod polymers by the PMFB technique. Using molecular theory for rigid polymers, birefringence Δn and orientation angle χ have been expressed as a function of molecular weight and distribution. Δn has been shown to be proportional to Σc_iM, and cot 2χ turned out to have a linear relationship with Σc_iM/Σc_iM. From the experimental results for PBLG solutions, birefringence and orientation angle data were in some degree matched with the theory presented. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 509–515, 2000     

Fluorescence enhancement of cationic diacetylene‐contained polyelectrolyte by anions and cations and application for sensitive and selective detection of Hg2+

An unusual phenomenon, the fluorescence enhancement of cationic conjugated fluorene‐co‐carbazole‐co‐diacetylene polymers (CPFC) by both anionic and cationic ions, was reported. The fluorescence enhancement of CPFC strongly depended on the nature of the ions and the counterions. In the solution of DMF/H₂O, PO, CO and Hg²⁺ showed the most pronounced fluorescence enhancement response of CPFC (more than 10‐fold). The fluorescence of CPFC was quenched by K₄[Fe(CN)₆, and then could be recovered with the addition of Hg²⁺. Based on these observations, a simple and sensitive fluorescent “turn‐on” sensor in aqueous solution for Hg²⁺ was developed by use of a system of CPFC/ K₄[Fe(CN)₆]. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Thermal,morphology, and NMR characterizations on phase behavior and miscibility in blends of isotactic polystyrene with poly(cyclohexyl methacrylate)

The miscibility and phase behavior in a binary blend of isotactic polystyrene (iPS) and poly(cyclohexyl methacrylate) (PCHMA) were investigated by differential scanning calorimetry, optical microscopy (OM), and solid‐state ¹³C cross‐polarity/magic‐angle spinning NMR. The iPS/PCHMA blend was miscible when all compositions showed a single composition‐dependent glass‐transition temperature (T_g) and when the blend went through a thermodynamic phase transition upon heating to above the lower critical solution temperature as determined by OM measurements. The ¹H NMR spin‐relaxation times in the laboratory frame (T) and in the rotating frame (T) for iPS/PCHMA blends with various compositions and neat components were directly measured through solid‐state¹³C NMR. The results of T indicated that the blends are homogeneous, at least on a scale of 75–85 nm, confirming the miscibility of the system. The single decay and composition‐dependent T values for each blend further demonstrated the blends are homogeneous on a scale of 2.5–3.5 nm. The results suggested that iPS and PCHMA are intimately mixed at the molecular level within the blends at all compositions. The tacticity of polystyrene does not seem to adversely influence the miscibility in blends of iPS/PCHMA. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 772–784, 2003     

Crystallization studies of poly(trimethylene terephthalate) using thermal analysis and far‐infrared spectroscopy

Crystallization of poly(trimethylene terephthalate) (PTT) by annealing was examined using density measurement, differential scanning calorimetry, and far‐infrared spectroscopy (FIR). Crystallinity, measured by density, increased slowly up to the T_a of 185 °C and increases rapidly once T_a exceeds 185 °C. It was found that thermally induced crystallization is mainly temperature‐dependent above T_a = 185 °C and temperature‐ and time‐dependent below T_a = 60 °C. Two melting transitions, T and T, were observed for those samples annealed above 120 °C. No significant change in T was observed as a function of T_a while T showed strong dependency on T_a. Digital subtraction of the amorphous contribution from the semicrystalline FIR spectra provided characteristic spectra of amorphous and crystalline PTT. The bands at 373, 282, and 92 cm^?1 were assigned to the crystalline phase, while the bands at 525, 406, and 351 cm^?1 were attributed to the amorphous phase. It was shown that FIR spectroscopy can be used as a means to estimate the degree of crystallinity of PTT. The band ratio of 373 and 501 cm^?1 was plotted against crystallinity measured by density and reasonably good correlation was obtained. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1675–1682, 2007     

Mass spectrometric evidence for collisionally induced removal of H2 from monoanions of 10B nido‐carborane derivatives investigated by electrospray ionization quadrupole linear ion trap and Fourier transform ion cyclotron resonance mass spectrometry

Some newly synthesized ¹⁰B nido‐carborane derivatives, i.e., 7,8‐dicarba‐nido‐undecaborane monoanions ([7‐Me‐8‐R‐C₂B₉H₁₀]^‐K⁺, R = H, butyl, hexyl, octyl and decyl), have been fully characterised and examined by electrospray ionization and Fourier transform ion cyclotron resonance mass spectrometry with liquid chromatographic separation (LC/ESI‐FTICR‐MS). These boron‐containing compounds exhibit abundant molecular ions ([M]^?) at m/z 140.22631 [CB₉H₁₄]^?, m/z 196.28883 [CB₉H₂₂]^?, m/z 224.32032 [CB₉H₂₆]^?, m/z 252.35133 [CB₉H₃₀]^? and m/z 280.38354 [CB₉H₃₄]^? at the normal tube lens voltage setting of ?90 V, which was an instrumental parameter value selected in the tuning operation. Additional [M–nH₂]^? (n = 1?4) ions were observed in the mass spectra when higher tube lens voltages were applied, i.e., ?140 V. High‐resolution FTICR‐MS data revealed the accurate masses of fragment ions, bearing either an even or an odd number of electrons. Collision‐induced dissociation of the [M–nH₂]^? ions (n = 0–4) in the quadrupole linear ion trap (LTQ) analyzer confirmed the loss of hydrogen molecules from the molecular ions. It is suggested that the loss of H₂ molecules from the alkyl chain is a consequence of the stabilization effect of the nido‐carborane charged polyhedral skeleton. Copyright © 2009 John Wiley & Sons, Ltd.     

Fractionation and characterization of a protein–polysaccharide complex from Pleurotus tuberregium sclerotia

A water‐soluble sample (TM4b), extracted from sclerotia of Pleurotus tuberregium, was analyzed using elemental analysis, one‐ and two‐dimensional ¹H and ¹³C NMR. The results indicated that TM4b was protein–polysaccharide complex, and the polysaccharide moiety was hyperbranched β‐D ‐glucan with residuals branched at C3, C2, C4, and C6 positions. A preparative size‐exclusion chromatography (SEC) column combined with nonsolvent addition method was used to fractionate TM4b, and nine fractions were obtained. Solution properties of TM4b in 0.15 M aqueous NaCl were studied using static laser light scattering and viscometry at 25 °C. The dependences of intrinsic viscosity ([η]) and radius of gyration (〈S²〉) on weight–average molecular weight (M_w) for TM4b in the M_w range from 1.89 × 10⁴ to 2.58 × 10⁶ were found to be [η] = 0.21M and 〈S²〉 = 3.63M. It indicated that TM4b existed as compact sphere conformation in the aqueous solution. Atomic force microscopy image further confirmed that the TM4b molecules exhibited globular shape in the solution. This work gave valuable information on fractionation and chain conformation characterization of the globular protein–polysaccharide complex. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2546–2554, 2007