Controlled radical copolymerization of styrene and maleic anhydride and the synthesis of novel polyolefin‐based block copolymers by reversible addition–fragmentation chain‐transfer (RAFT) polymerization

Reversible addition–fragmentation chain transfer (RAFT) was applied to the copolymerization of styrene and maleic anhydride. The product had a low polydispersity and a predetermined molar mass. Novel, well‐defined polyolefin‐based block copolymers were prepared with a macromolecular RAFT agent prepared from a commercially available polyolefin (Kraton L‐1203). The second block consisted of either polystyrene or poly(styrene‐co‐maleic anhydride). Furthermore, the colored, labile dithioester moiety in the product of the RAFT polymerizations could be removed from the polymer chain by UV irradiation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3596–3603, 2000     

Novel polystyrene‐supported zirconocene catalyst for olefin polymerization and its catalytic kinetics

Through the Diels–Alder reaction between cyclopentadiene groups attached to polystyrene in the presence of zirconocene, novel polystyrene‐supported metallocene catalysts were prepared. A novel method for immobilizing metallocene catalysts was investigated, and the resultant polystyrene‐supported metallocene for olefin polymerization was studied. The results of olefin polymerization showed that different crosslinking degrees of support in the catalyst system had significant effects on the catalytic behavior. The influence of the [Al]/[Zr] molar ratio and the temperature on the (co)polymerization activity was studied. When 1‐hexene and 1‐dodecene were used for copolymerization with ethylene, an obvious positive comonomer effect was observed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2650–2656, 2005     

Multiblock poly(4‐vinylpyridine) and its copolymer prepared with cyclic trithiocarbonate as a reversible addition–fragmentation transfer agent

The polymerization of 4‐vinylpyridine was conducted in the presence of a cyclic trithiocarbonate (4,7‐diphenyl‐[1,3]dithiepane‐2‐thione) as a reversible addition–fragmentation transfer (RAFT) polymerization agent, and a multiblock polymer with narrow‐polydispersity blocks was prepared. Two kinds of multiblock copolymers of styrene and 4‐vinylpyridine, that is, (ABA)_n multi‐triblock copolymers with polystyrene or poly(4‐vinylpyridine) as the outer blocks, were prepared with multiblock polystyrene or poly(4‐vinylpyridine) as a macro‐RAFT agent, respectively. GPC data for the original polymers and polymers cleaved by amine demonstrated the successful synthesis of amphiphilic multiblock copolymers of styrene and 4‐vinylpyridine via two‐step polymerization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2617–2623, 2007     

Pore size in one‐step swelling and polymerization of monodisperse polymer beads

Crosslinked polystyrene beads were prepared at low swelling ratios by one‐step swelling and polymerization method. Pore size of the beads was observed based on the GPC calibration curves. It is found that: (1) the pore size increases as the swelling ratio decreases; (2) when a good solvent is used as the porogen the pore size increases with the crosslinking monomer content; and (3) at high crosslinking monomer content the pore size does not depend on the porogen solubility. The effects are discussed in terms of polymer miscibility, including phase separation between the seed and bead polymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3270–3277, 2000     

LCP aromatic polyesters by esterolysis melt polymerization

Polyarylates have previously been synthesized from acetate esters via esterolysis (loss of methyl acetate). This polycondensation can be extended to p‐substituted aromatic monomers for liquid crystal polyesters (LCPs). For AB‐type polymers, methyl p‐acetoxybenzoate and methyl 6‐acetoxynaphthoate were copolymerized to an LCP with reasonable molecular weights. Benzoate esters, methyl 4‐benzoyloxybenzoate (MBB) and methyl 6‐benzoyloxy‐2‐naphthoate (MBN), are also investigated. Several tin and antimony oxide catalysts were effective. The rate of esterolysis polymerization of MBB and MBN is slower than that of the corresponding acidolysis melt polymerization, but fast enough to give relatively high‐molecular‐weight polymers and similar thermal stability as commercial LCP prepared by acidolysis. Using these alternative benzoyloxy groups significantly reduced the color problem, because ketene loss cannot occur. Esterolysis melt polymerizations leading to AB/AABB‐type LCPs were performed using either dimethyl 2,6‐naphthalene dicarboxylate (DMND) or dimethyl terephthalate (DMT) with methyl 4‐acetoxybenzoate and phenylhydroquinone diacetate with tin and antimony catalysts. DMT‐based monomer compositions show much faster polymerization than DMND‐based compositions using antimony oxide catalyst. All these LCPs show a T_g in the 140–170 °C range as a result of the inclusion of the naphthalene and/or phenyl hydroquinone units in the polymer chain. Compositions completely off‐balanced on either side still lead to relatively high‐molecular‐weight copolyesters because either excess monomer can be removed during polymerization. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3586–3595, 2000     

Anionic synthesis and detection of fluorescence‐labeled polymers with a terminal anhydride group

To monitor polymer–polymer coupling reactions between two different monofunctional polymers in dilute polymer blends, fluorescence‐labeled anhydride‐functional polystyrene (PS) and poly(methyl methacrylate) (PMMA) were prepared by conventional anionic polymerization. Sequential trapping of lithiopolystyrene by 1‐(2‐anthryl)‐1‐phenylethylene (APE) and then di‐t‐butyl maleate (4) provided, after pyrolysis, anhydride‐functional fluorescent PS. Fluorescent PMMA anhydride (8) was synthesized with sec‐butyllithium/APE as an initiator for the anionic polymerization of methyl methacrylate, trapping by 4, and pyrolysis. These polymers could be reacted with amine‐functional polymers by melt blending, and the reaction progress could be monitored by gel permeation chromatography coupled with fluorescence detection. This technique not only allows monitoring of the coupling reaction with high sensitivity (ca. 100 times more sensitive than refractive index detection) but also permits selective detection because unlabeled polymers are invisible to fluorescence detection. This highly sensitive and selective detection methodology was also used to monitor the coupling reaction of 8 with PS‐NH₂ at a thin‐film interface, which was otherwise difficult to detect by conventional methods. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2177–2185, 2000     

Polymerization of 4‐methylpentene and vinylcyclohexane by amine bis(phenolate) titanium and zirconium complexes

The polymerization of the substituted olefins 4‐methylpentene and vinylcyclohexane by dibenzyl titanium and zirconium complexes of three amine bis(phenolate) ligands is reported. The ligands featured a dimethylamino side‐arm donor and either electron‐withdrawing (Cl and Br) or methyl phenolate substituents. After activation with B(C₆F₅)₃, the zirconium catalysts exhibited a higher activity than the titanium catalysts toward these bulky olefins. Very high weight‐average molecular weight poly(4‐methylpentene) was obtained with the zirconium catalysts. The zirconium catalysts were employed in 1‐hexene polymerization, and their activity was found to be the highest ever reported for catalysts of the amine bis(phenolate) family. The catalysts featuring methyl phenolate substituents showed a higher activity toward these substituted olefins than the electron‐poor catalysts; this trend was opposite to their activity toward 1‐hexene. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1136–1146, 2006     

Polymer‐supported half‐titanocene catalysts for the syndiospecific polymerization of styrene

Monocyclopendienyltitanium trichloride (CpTiCl₃) was supported on polymer carriers with different hydroxyl contents, and the supported catalysts were used for styrene polymerization. The supported catalysts exhibited high activity even at low Al/Ti ratios and increased the molecular weight of the products, indicating that polymer carriers could stabilize the active sites. The polymers prepared with unsupported and supported catalysts were extracted with boiling n‐butanone and characterized by carbon nuclear magnetic resonance (¹³C NMR) and differential scanning calorimetry. The polymers obtained by supported catalysts had a high fraction of boiling n‐butanone‐insoluble part and high melting temperatures, but ¹³C NMR results showed that syndiotacticity decreased compared with that of polymers prepared with an unsupported catalyst. ESR study on the supported catalysts confirmed that the active sites supported on the carrier dropped into the solution and formed active sites the same as those in the unsupported system when they reacted with methylaluminoxane. ¹³C NMR analysis showed that the polymerization mechanism of the supported active sites was an active‐site controlled mechanism instead of a chain‐end controlled mechanism of the unsupported active sites. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 127–135, 2000     

Synthesis of quaternary ammonium ion‐grafted polyolefins via activation of inert C?H bonds and nitroxide mediated radical polymerization

A TEMPO‐functionalized isotactic poly(1‐butene) macroinitiator was synthesized via rhodium‐catalyzed activation of the alkane C? H bonds in polyolefin side chain using a boron reagent and subsequent transformations of the boronate ester group in the polymer. These functionalization processes did not induce cross‐linking or degradation of the polymer chains. Nitroxide mediated radical polymerization of dipropyl(4‐vinylphenyl)amine with the macroinitiator produced high‐molecular weight amine‐grafted copolymers of the polyolefin. Adjusting the ratio of polar monomer concentration to macroinitiator concentration controlled the concentrations of amine blocks in the graft copolymers up to 10 mol %. Quaternization of the amine‐grafted copolymers with methyl triflate generated ammonium ion blocks along the side chain of the graft copolymers. A systematic decrease of contact angle in a series of ammonium ion‐grafted copolymers was observed through water contact angle measurements, suggesting that the graft polymerization and the quaternization led to increased hydrophilicity in the polymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4519–4531, 2009     

End‐group fidelity in nitroxide‐mediated living free‐radical polymerizations

In this study, new nitroxides based on the 2,2,5‐trimethyl‐4‐phenyl‐3‐azahexane‐3‐oxy skeleton were used to examine chain‐end control during the preparation of polystyrene and poly(t‐butyl acrylate) under living free‐radical conditions. Alkoxyamine‐based initiators with a chromophore attached to either the initiating fragment or the mediating nitroxide fragment were prepared, and the extent of the incorporation of the chromophores at either the initiating end or the propagating chain end was determined. In contrast to 2,2,6,6‐tetramethyl piperidinoxy (TEMPO), the incorporation of the initiating and terminating fragment into the polymer chain was extremely high. For both poly(t‐butyl acrylate) and polystyrene with molecular weights less than or equal to 70,000, incorporations at the initiating end of greater than 97% were observed. At the terminating chain end, incorporations of greater than 95% were obtained for molecular weights less than or equal to 50,000. The level of incorporation tended to decrease slightly at higher molecular weights because of the loss of the alkoxyamine propagating unit, which had important consequences for block copolymer formation. These results clearly show that these new α‐H nitroxides could control the polymerization of vinyl monomers such as styrene and t‐butyl acrylate to an extremely high degree, comparable to anionic and atom transfer radical polymerization procedures. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4749–4763, 2000     

End‐capping of polystyrene by aliphatic primary amine by derivatization of precursor hydroxyl end group

A new and very efficient route for the synthesis of aliphatic primary amine terminated polystyrene (PS) is reported. In contrast to most known methods, only traditional commercially available reagents are used. PS is synthesized by anionic polymerization with a lithium counter ion and the living chains are end‐capped by a hydroxyl group upon addition of ethylene oxide followed by protonation. The ω‐hydroxyl end group is tosylated and the tosylate is then reacted with sodium azide. The azide terminal group is finally reduced into primary amine. The different steps of functionalization have been fully characterized by SEC, ToF‐SIMS, FTIR, and ¹H NMR. The amine content (= 98%) has been determined by acid‐base titration with perchloric acid. It clearly shows the efficiency of the synthetic method reported in this article although it is a multistep method. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1618–1629, 2000     

A Self‐Supporting Strategy for Gas‐Phase and Slurry‐Phase Ethylene Polymerization using Late‐Transition‐Metal Catalysts

The polyolefin industry is dominated by gas‐phase and slurry‐phase polymerization using heterogeneous catalysts. In contrast, academic research is focused on homogeneous systems, especially for late‐transition‐metal catalysts. The heterogenization of homogeneous catalysts is a general strategy to provide catalyst solutions for existing industrial polyolefin synthesis. Herein, we report an alternative, potentially general strategy for using homogeneous late‐transition‐metal catalysts in gas‐phase and slurry‐phase polymerization. In this self‐supporting strategy, catalysts with moderate chain‐walking capabilities produced porous polymer supports during gas‐phase ethylene polymerization. Chain walking, in which the metal center can move up and down the polymer chain during polymerization, ensures that the metal center can travel along the polymer chain to find suitable sites for ethylene enchainment. This strategy enables simple heterogenization of catalysts on solid supports for slurry‐phase polymerization. Most importantly, various branched ultra‐high‐molecular‐weight polyethylenes can be prepared under various polymerization conditions with proper catalyst selection.     

Atom transfer radical polymerization of styrene and methyl methacrylate catalyzed by FeCl2/iminodiacetic acid

The atom transfer radical polymerization of styrene and methyl methacrylate with FeCl₂/iminodiacetic acid as the catalyst system in bulk was successfully implemented at 70 and 110 °C, respectively. The polymerization was controlled: the molecular weight of the resultant polymer was close to the calculated value, and the molecular weight distribution was relatively narrow (weight‐average molecular weight/number‐average molecular weight ∼ 1.5). Block copolymers of polystyrene‐b‐poly(methyl methacrylate) and poly(methyl methacrylate)‐b‐poly(methyl acrylate) were successfully synthesized, confirming the living nature of the polymerization. A small amount of water added to the reaction system increased the reaction rate and did not affect the living nature of the polymerization system. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4308–4314, 2000     

Polymerization of styrene with nickel complex/methylaluminoxane catalytic systems

Polymerization of styrene using catalytic systems based on nickel derivatives and methylaluminoxane (MAO) was studied. Among tested catalysts, nickel bis(acetylacetonate) and nickel dichloride show the maximum activity. Bis(phosphine)nickel dichlorides exhibit lower activity, depending on the nature of the phosphine ligand. Polymer yields decrease by lowering the catalyst concentration, by increasing the reaction temperature, or by carrying out the polymerization in a polar donor solvent. Weight average molecular weight of most of the prepared polystyrenes ranges from 9000 to 25,000, with polydispersity indexes of 1.6–3.8. However, polystyrene prepared in dioxane solvent exhibits a small fraction of very high molecular weight (about 140,000). From NMR analysis, the products seem generally to be constituted of two polymers with different steric microstructure: atactic polystyrene and partially isotactic polystyrene (ca. 75–85% meso diads). Catalytic site specificity is correlated with the type of nickel ligand, while the effect of reaction temperature is less defined. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2119–2126, 1998     

Syntheses of polyolefin‐based stereoregular diblock copolymers for self‐assembled nanostructures

The preparation of polyolefin‐based stereoregular diblock copolymers by postpolymerization of ethenyl‐capped syndiotactic polypropylene‐based propylene/norbornene copolymer (sPP‐based P‐N copolymer) led to the successful generation of a structurally uniform stereoregular diblock copolymer for self‐assembly studies. The ethenyl‐capped prepolymer was prepared by conducting propylene/norbornene copolymerization in the presence of Me₂C(Cp)(Flu)ZrCl₂/MAO. Ozonolysis of ethenyl‐capped sPP‐based P‐N copolymer provided the formyl group end‐capped, end‐functionalized prepolymer with a quantitative functional group conversion ratio. Subsequently, connecting the formyl end‐group of the stereoregular prepolymer by coupling with living anionic polystyrene resulted in the high yield production of stereoregular diblock copolymer (sPP‐based P‐N‐block‐polystyrene), which is difficult to prepare by other methods. The resulting stereoregular diblock copolymer possesses precise chemical architecture to self‐organize into consistent nanostructures as evidenced by transmission electron microscopy and small angle X‐ray scattering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4843–4856, 2008     

Copolymerization of ethylene and α‐olefins with combined metallocene catalysts. II. Mathematical modeling of polymerization with single metallocene catalysts

The relation between the polymerization conditions and the distributions of molecular weight (MWD) and chemical composition (CCD) of poly(ethylene‐co‐1‐hexene) made with single supported metallocene catalysts was investigated. Understanding the behavior of each metallocene under different polymerization conditions is necessary for designing combined metallocene catalysts to produce tailor‐made polyolefins. In this article, a simple mathematical model based on experimental results is developed and combined with the bimodality criterion developed in Part I of this series to predict polymerization conditions and metallocene combinations that will produce polymers with desired MWDs and CCDs. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1417–1426, 2000     

Polymerization of vinyl monomers photoinitiated by p‐nitroaniline: Photoinitiation mechanism

The polymerization rate of methyl methacrylate photoinitiated by p‐nitroacetanilide in the presence of triethylamine was measured as a function of the amine concentration in different media. The polymerization is more efficient in nonpolar medium (benzene/monomer). ESR studies show the formation of a nitro and an amino free radical, which are formed by photoinduced proton transfer from the amine to the nitro group. The amine radical is the active species that adds to the monomer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2269–2273, 2000     

Synthesis of new amphiphilic diblock copolymers containing poly(ethylene oxide) and poly(α‐olefin)

This article discusses an effective route to prepare amphiphilic diblock copolymers containing a poly(ethylene oxide) block and a polyolefin block that includes semicrystalline thermoplastics, such as polyethylene and syndiotactic polystyrene (s‐PS), and elastomers, such as poly(ethylene‐co‐1‐octene) and poly(ethylene‐co‐styrene) random copolymers. The broad choice of polyolefin blocks provides the amphiphilic copolymers with a wide range of thermal properties from high melting temperature ～270 °C to low glass‐transition temperature ～?60 °C. The chemistry involves two reaction steps, including the preparation of a borane group‐terminated polyolefin by the combination of a metallocene catalyst and a borane chain‐transfer agent as well as the interconversion of a borane terminal group to an anionic (? O^?K⁺) terminal group for the subsequent ring‐opening polymerization of ethylene oxide. The overall reaction process resembles a transformation from the metallocene polymerization of α‐olefins to the ring‐opening polymerization of ethylene oxide. The well‐defined reaction mechanisms in both steps provide the diblock copolymer with controlled molecular structure in terms of composition, molecular weight, moderate molecular weight distribution (M_w/M_n < 2.5), and absence of homopolymer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3416–3425, 2002     

Olefin polymerization by cyclopentadienyltris(dimethylamido)titanium(IV) complexes

Several titanium(IV) complexes of the type Cp′Ti(NMe₂)₃ [Cp′ = cyclopentadienyl ( 1 ), (dimethylaminoethyl)cyclopentadienyl ( 2 ), indenyl ( 3 ), and pentamethylcyclopentadienyl ( 4 )] were prepared, and their catalytic properties in the polymerization of α‐olefins were examined. Complexes 1 and 2 catalyzed the polymerization of ethylene in the presence of methylaluminoxane with a much higher activity than 3 or 4 . Complexes 3 and 4 polymerized ethylene with an activity similar to that of CpTiCl₃ ( 6 ). The preactivation of 2 , 3 , or 4 with trimethylaluminum (TMA) resulted in an increase in ethylene polymerization activities. Also, 1 and 2 were successfully used as ethylene/1‐hexene copolymerization catalysts, producing polymers with various amounts of 1‐hexene incorporation, depending on the amount of 1‐hexene in the feed mixture. Complex 1 likewise effectively polymerized styrene with a higher activity and higher syndiospecificity than the other three catalysts. Complexes 3 and 4 polymerized styrene with low syndiospecificity, whereas 2 produced only atactic polystyrene. The preactivation of 3 or 4 with TMA resulted in an increase in styrene polymerization activities and increased the syndiotacticity percentage of the polymers produced. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 313–319, 2001     

Ethylene polymerization with porous polystyrene spheres supported Cp2ZrCl2 catalyst

A catalyst with porous polystyrene beads supported Cp₂ZrCl₂ was prepared and tested for ethylene polymerization with methylaluminoxane as a cocatalyst. By comparison, the porous supported catalyst maintained higher activity and produced polyethylene with better morphology than its corresponding solid supported catalyst. The differences between activities of the catalysts and morphologies of the products were reasonably explained by the fragmentation processes of support as frequently observed with the inorganic supported Ziegler–Natta catalysts. Investigation into the distribution of polystyrene in the polyethylene revealed the fact that the porous polystyrene supported catalyst had undergone fragmentation during polymerization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3313–3319, 2003