Stress overshoot of polymer solutions at high rates of shear

Overshoot of shear stress, σ, and the first normal stress difference, N₁, in shear flow were investigated for polystyrene solutions. The magnitudes of shear corresponding to these stresses, γ_σm and γ_Nm, for entangled as well as nonentangled solutions were universal functions of γ˙τ_eq, respectively, and γ_Nm was approximately equal to 2γ_σm at any rate of shear, γ˙. Here τ_eq = τ_R for nonentangled systems and τ_eq = 2τ_R for entangled systems, where τ_R is the longest Rouse relaxation time evaluated from the dynamic viscoelasticity at high frequencies. Only concentrated solutions exhibited stress overshoot at low reduced rates of shear, γ˙τ_eq < 1. The behavior at very low rates, γ˙τ_eq < 0.2, was consistent with the Doi–Edwards tube model theory for entangled polymers. At high rates, γ˙τ_eq > 1, γ_σm and γ_Nm were approximately proportional to γ˙τ_eq. At very high rates of shear, the peak of σ is located at t = τ_R, possibly indicating that the polymer chain shrinks with a characteristic time τ_R in dilute solutions. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1917–1925, 2000     

Stress overshoot of polymer solutions at high rates of shear; Polystyrene with bimodal molecular weight distribution

Overshoot of shear stress, σ, and the first normal stress difference, N₁, in shear flow was investigated for dilute solutions of polystyrene with very high molecular weight in concentrated solution of low M PS. In the case that the matrix was a nonentangled system, behavior of overshoot was similar to that of dilute solution of high M PS in pure solvent. The magnitudes of shear, γ_σm and γ_Nm, corresponding to the peaks of σ and N₁ lay on the universal functions of γ˙τ_R, respectively, proposed for dilute solutions in pure solvent. Here τ_R is the Rouse relaxation time for high M PS in the blend evaluated from dynamic modulus at high frequencies. In the case that the matrix was an entangled system, an additional σ peak was observed at high rates of shear at times corresponding to γ_σm = 2–3. This peak can be assigned to the motion of low M chains in entanglement network. When the matrix was entangled, stress overshoot was observed even at relatively low rates of shear, say γ˙τ_R < 10⁻². This is probably due to the motion of high M chains in entanglement of all the chains. In this case the γ_σm and γ_Nm values were higher than those expected for entangled chains of monodisperse polymer in pure solvent. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2043–2050, 2000     

Rheology of polystyrene solutions around the coil overlapping concentration: A phenomenological description of stresses in simple shear flow

Linear viscoelasticity behavior is described with the sum of two terms for polystyrene solutions in tricresyl phosphate around the coil overlapping concentration (K. Osaki, T. Inoue, & T. Uematsu, J Polym Sci Part B: Polym Phys 2001, 39, 211). One is a Rouse–Zimm (RZ) term represented by the Zimm theory with arbitrarily chosen values of the hydrodynamic interaction parameter and the longest relaxation time (τ_RZ). The other (the L term) consists of a relaxation mode with a single relaxation time (τ_L > τ_RZ) and a high‐frequency limiting modulus proportional to the square of the concentration. In this study, we describe the viscosity (η) and first normal stress coefficient (Ψ₁) in steady shear with simple formulas. The stress due to the L term is assumed to be given by a Kaye, Bernstein, Kearsley, and Zapas (K‐BKZ) equation with the damping function h(γ) = (1 + 0.2γ²)^?1/2, where γ is the magnitude of shear. Contributions to η and Ψ₁ from the RZ term are derived from the RZ model, in which the relaxation time in steady flow is given by τ_st = τ + (τ_RZ ? τ)/(1 + 0.35τ_RZ γ˙) instead of τ_RZ. Here, γ˙ is the rate of shear, and τ is the τ_RZ value at the infinite dilution limit. η and Ψ₁ at various concentrations for two polystyrene samples (with molecular weights of 2890 and 8420 kg mol^?1) are well described with parameters derived from dynamic viscoelasticity. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1038–1045, 2002     

Viscoelastic properties of dilute polymer solutions: The effect of varying the concentration

Dynamic viscoelastic behavior was investigated for solutions of polystyrene in tricresyl phosphate, a good solvent, at concentrations, c, less than the coil‐overlapping concentration, c*. At the infinite dilution limit, the behavior was in accord with the theory of Doi and Edwards involving the excluded volume potential and hydrodynamic interaction (HDI). Thus, the viscoelastic functions were completely derived from the intrinsic viscosity–molecular weight relation. At finite c, the complex modulus was represented by the sum of two terms. One was a Rouse–Zimm (RZ) term conveniently represented by the Zimm theory with an arbitrarily chosen value of the HDI parameter. The other was a term with a single relaxation time, longer than the longest RZ relaxation time, and with a high‐frequency modulus proportional to the square of c [the long‐time (LT) term]. The behavior of the RZ term indicated the stronger screening of HDI with increasing c. Using the experimental c dependence of the longest RZ relaxation time to get the relevant parameter, we compared the RZ viscoelastic function with the Muthukumar–Freed theory. The agreement was good at low concentrations, c < c*. The contribution of the LT term, which was not included in the theory, was quite significant at low frequencies; about 60% of the Huggins coefficient was attributable to this term. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 211–217, 2001     

Rheological measurements and light-scattering experiments of dilute solutions of high molecular polystyrene. Light-scattering of flowing polymer solutions

We describe the behavior of dilute polymer solutions by means of light-scattering under shear flow. Solution properties of polystyrene in benzene over a wide range of molecular weight has been studied to determine the coefficientsa andK of the Mark-Houwink relationship and to estimate the rheological conditions with regard to light-scattering experiments of flowing polymer solutions. The investigations were carried out to measure the shear-rate dependence of macromolecules in solution, e.g., to observe an orientation and changing of the mean-square radius of gyration.     

On the nature of phase separation of polymer solutions at high extension rates

Experiments with stretching moderately concentrated polymer solutions have been carried out. Model experiments were carried out for poly(acrylonitrile) solutions in dimethyl siloxane. Just the choice of concentrated solutions allowed for a clear demonstration of a demixing effect with the formation of two separate phases—an oriented polymer fiber and solvent drops sitting on its surface. An original experimental device for following all subsequent stages in the demixing process was built. It combined two light beams, one transverse to the fiber and a second directed along (inside) the fiber, the latter played the role of an optical line. This gives a unique opportunity to observe processes occurring inside a fiber. The process of demixing starts from the volume phase separation across the whole cross section of a fiber at some critical deformation and the propagation of the front of demixing along the fiber. Then a solvent cylindrical skin appears which transforms into a system of separate droplets. New experimental data are discussed based on a comparison of the current different points of view on the phenomenon of deformation‐induced phase separation: thermodynamic shift of the equilibrium phase transition temperature, growth of stress‐induced concentration fluctuations in two‐component fluids, and mechanically pressing a solvent out from a polymer network. The general belief is that a rather specific (so‐called “beads‐on‐a‐string”) structure of a filament is realized in stretching dilute solutions: beads of a polymer solution connected by oriented polymer bridges forming a single object. The situation in stretching moderately concentrated solutions appears quite different: real phase separation was observed. So, the alternative phenomenon to the formation of the “beads‐on‐a‐string” structure has been experimentally proven. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 559–565     

Electrophoretic mobility of linear and star-branched DNA in semidilute polymer solutions

Electrophoresis of large linear T2 (162 kbp) and 3-arm star-branched (N(Arm) = 48.5 kbp) DNA in linear polyacrylamide (LPA) solutions above the overlap concentration c* has been investigated using a fluorescence visualization technique that allows both the conformation and mobility mu of the DNA to be determined. LPA solutions of moderate polydispersity index (PI approximately 1.7-2.1) and variable polymer molecular weight Mw (0.59-2.05 MDa) are used as the sieving media. In unentangled semidilute solutions (c* < c < c(e)), we find that the conformational dynamics of linear and star-branched DNA in electric fields are strikingly different; the former migrating in predominantly U- or I-shaped conformations, depending on electric field strength E, and the latter migrating in a squid-like profile with the star-arms outstretched in the direction opposite to E and dragging the branch point through the sieving medium. Despite these visual differences, mu for linear and star-branched DNA of comparable size are found to be nearly identical in semidilute, unentangled LPA solutions. For LPA concentrations above the entanglement threshold (c > c(e)), the conformation of migrating linear and star-shaped DNA manifest only subtle changes from their unentangled solution features, but mu for the stars decreases strongly with increasing LPA concentration and molecular weight, while mu for linear DNA becomes nearly independent of c and Mw. These findings are discussed in the context of current theories for electrophoresis of large polyelectrolytes.     

Viscometric properties of dilute polystyrene/dioctyl phthalate solutions

We report viscometric data collected in a Couette rheometry on dilute, single‐solvent polystyrene (PS)/dioctyl phthalate (DOP) solutions over a variety of polymer molecular weights (5.5 × 10⁵ ≤ M_w ≤ 3.0 × 10⁶ Da) and system temperatures (288 K ≤ T ≤ 318 K). In view of the essential viscometric features, the current data may be classified into three categories: The first concerns all the investigated solutions at low shear rates, where the solution properties are found to agree excellently with the Zimm model predictions. The second includes all sample solutions, except for high‐molecular‐weight PS samples (M_w ≥ 2.0 × 10⁶ Da), where excellent time–temperature superposition is observed for the steady‐state polymer viscosity at constant polymer molecular weights. No similar superposition applies at a constant temperature but varied polymer molecular weights, however. The third appears to be characteristic of dilute high‐molecular‐weight polymer solutions, for which the effects of temperature on the viscosity curve are further complicated at high shear rates. The implications concerning the relative importance of hydrodynamic interactions, segmental interactions, and chain extensibility with increasing polymer molecular weight, system temperature, and shear rate are discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 787–794, 2006     

Rheological properties of wood polymer composites at high shear rates

This paper presents the rheological properties of wood-polymer composites (WPC) with a polypropylene (PP) matrix in the corrected shear rate range from approx. 20 s⁻¹ to 150 000 s⁻¹. Tests were conducted using a capillary rheometer and a rheological head of the author's construction, for which the working element is a thermoplastic injection moulding machine. The constructed tool was found to be very useful, especially for the determination of the processing characteristics of WPC composites containing a large particle-size filler. It was observed that the rheological properties of wood-polymer composites in the shear rate range of up to several thousand s⁻¹ significantly depended on the filler content of the polymer matrix; at the same time, at higher shear rate, a clear decrease in the effect of the wood filler content on the viscosity of the composites and on the flow behaviour, as described by the power law, took place.     

Short‐time stretch relaxation of entangled polymer solutions investigated using full Rouse model predictions

We conduct a systematical investigation into the short‐time stretch relaxation behavior (i.e., shorter than the Rouse time but sufficiently longer than the glassy time) of entangled polymer liquid in single‐step strain flows, on the basis of theory/data comparisons for a broad series of type‐A entangled polymer solutions. First, within existing normal‐mode formulations, the Rouse model predictions on a full‐chain stretch relaxation in single‐step strain flows are derived for a popular 1‐D model proposed within the Doi–Edwards tube model, as well as for the original 3‐D model for nonentangled systems. In addition, an existing formula for the aforementioned 1‐D model that, however, rested upon a consistent‐averaging or the so‐called uniform‐chain‐stretch approximation is simultaneously examined. Subsequently, the previously derived formulas on chain stretch relaxation are directly incorporated into a reliable mean‐field tube model that utilizes the linear relaxation spectrum and the Rouse time constant consistently determined from linear viscoelastic data. It is found that the predictions of the 1‐D model differ substantially from that of the original 3‐D model at short times. Theory/data comparisons further indicate that the 1‐D model without approximations seems able to describe fairly well the nonlinear relaxation data under investigation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1199–1211, 2006     

Studies on the viscosity behavior of polymer solutions at low concentrations

Viscosity measurements had been made on poly(vinyl alcohol) (PVA), poly(N-vinyl-2-pyrrolidone) (PVP) and poly(ethylene oxide) (PEO) solutions down to low concentrations. It was found that defined as the flow time of the pure solvent in ideal conditions and obtained practically by extrapolating the flow time of polymer solution t to zero concentration, was not equal to the flow time of the pure solvent t₀ measured. The reduced viscosity η_sp/C determined by (t/t₀-1)/C exhibited either a drastic increase or a significant decrease with dilution, depending upon the polymer solution investigated. On the other hand, η_sp/C determined by was proportional to C even at low concentrations. The anomalous viscosity behavior of neutral polymer solutions at low concentrations, therefore, was due to the incorrect method by which η_sp/C was determined. The detailed experiments indicated that the effective diameter of the viscometer capillary, the surface property of the capillary wall and the additional pressure corresponding to the measurement of t and t₀ for PVA, PVP and PEO solutions were not the same. Taking into account the contact anger and the surface tension of the liquid, together with the geometric parameter of the viscometer, the influence of the additional pressure upon the flow time measurement could be studied quantitatively. The calculation was in a good agreement with the experimental result. According to the method presented in this paper, the thickness of the adsorbed polymer layers on the capillary walls could be determined. It was noted that the thickness of the adsorbed polymer layers on the capillary walls was closely related to the solvent in which the polymer molecules were dissolved. The polymer molecular weight, however, had little or no effect on the thickness of the adsorbed polymer layers on the walls of the viscometer capillary.     

Adsorption-entanglement layers in flowing high molecular weight polymer solutions IV. The rates of layer formation and decay

Adsorption-entanglement layers are thick (i. e. multimolecular) layers which form at solid surfaces during flow of high molecular weight polymer solutions. This publication, the final part of the present series, is concerned with the rates at which such layers are formed and at which once formed they decay. It is shown that the rate of layer formation depends linearly on the shear rate applied. It is also demonstrated that the rate at which the layers decay is much slower than the rate at which they form. From the results presented in this paper, together with those in previous parts of this series [1–3], a qualitative model which accounts for the observed behaviour is deduced.     

Effects of chain entanglement on liquid-liquid phase separation behavior of LCST-type polymer blends: Cloud point and decomposition rate

By preparing homogenous blend samples with different degrees of chain entanglement, we report an anomalous contribution of chain entanglement to phase separation temperature and rate of poly(methyl methacrylate)/poly(styrene-comaleic anhydride)(PMMA/SMA) blends presenting a typical lower critical solution temperature(LCST) behavior. The meltmixed PMMA/SMA blends with a higher chain entanglement density present a lower cloud point(Tc) and shorter delay time, but lower phase separation rate at the given temperature than solution-cast ones, suggesting that for the polymer blends with different condensed state structure, thermodynamically more facilitation to phase separation(lower Tc) is not necessarily equivalent to faster kinetics(decomposition rate). The experimental results indicate that the lower Tc of melt-mixed sample is ascribed to smaller concentration fluctuation wavelength(Λm) induced by higher entanglement degree, while higher entanglement degree in melt-mixed sample leads to a confined segmental dynamics and consequently a slower kinetics(decomposition rate) dominated by macromolecular diffusion at a comparable quench depth. These results reveal that the chain packing in polymer blends can remarkably influence the liquid-liquid phase separation behavior, which is a significant difference from decomposition of small molecular mixtures.     

Static and dynamic scaling behavior of a polymer melt model with triple-well bending potential

We perform molecular-dynamics simulations for polymer melts of the coarse-grained poly(vinyl alcohol) model that crystallizes upon slow cooling. To establish the properties of its high temperature, liquid state as a reference point, we characterize in detail the structural features of equilibrated polymer melts with chain lengths 5 ≤ N ≤ 1000 at a temperature slightly above their crystallization temperature. We find that the conformations of sufficiently long polymers with N > 50 obey essentially the Flory's ideality hypothesis. The chain length dependence of the end-to-end distance and the gyration radius follow the scaling predictions of ideal chains and the probability distributions of the end-to-end distance, and form factors are in good agreement with those of ideal chains. The intrachain correlations reveal evidences for incomplete screening of self-interactions. However, the observed deviations are small. Our results rule out any preordering or mesophase structure formation that are proposed as precursors of polymer crystallization in the melt. Moreover, we characterize in detail primitive paths of long entangled polymer melts and we examine scaling predictions of Rouse and the reptation theory for the mean squared displacement of monomers and polymers center of mass. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1376–1392     

Isotope and pressure effects in polymer solutions. Demixing of polystyrene(h/d) poly-2-chlorostyrene blends

Liquid-liquid demixing, following spinodal quenches of poly-2-chlorostyrene/polystyrene blends, was followed by light scattering at 632.8 nm. The dependences of demixing on H/D substitution and molecular weight of the polystyrene, and on pressure, are reported. In the region of interest, the phase diagram is of the lower critical solution (LCS) type, and demixing is induced by raising the temperature. The transition temperature is lowered by deuterium substitution. At constant quench depth the transition proceeds more rapidly at elevated pressure. © 1995 John Wiley & Sons, Inc.     

Nonlinear rheology of highly entangled polymer solutions in start‐up and steady shear flow

Orientation angle and stress‐relaxation dynamics of entangled polystyrene (PS)/diethyl phthalate solutions were investigated in steady and step shear flows. Concentrated (19 vol %) solutions of 0.995, 1.81, and 3.84 million molecular weight (MW) PS and a semidilute (6.4 vol %) solution of 20.6 million MW PS were used to study the effects of entanglement loss on dynamics. A phase‐modulated flow birefringence apparatus was developed to facilitate measurements of time‐dependent changes in optical equivalents of shear stress (n₁₂ ≈ Cσ) and first normal stress differences (n₁ = n₁₁ ? n₂₂ ≈ CN₁) in a planar‐Couette shear‐flow geometry. Flow birefringence results were supplemented with cone‐and‐plate mechanical rheometry measurements to extend the range of shear rates over which entangled polymer dynamics are studied. In slow (τ > ) steady shear‐flow experiments using the ultrahigh MW polymer sample (20.6 × 10⁶ MW PS), steady‐state n₁₂ and n₁ results manifest unusual power‐law dependencies on shear rate [n_12,ss ～ ^0.4 and n_1,ss ～ ^0.8]. At shear rates in the range τ < < τ, steady‐state orientation angles χ_SS are found to be nearly independent of shear rate for all but the most weakly entangled materials investigated. For solutions containing the highest MW PS, an approximate plateau orientation angle χ_p in the range 20–24° is observed; χ_p values ranging from 14 to 16° are found for the other materials. In the start‐up of fast steady shear flow (γ˙ ≥ τ), transient undershoots in orientation angle are also reported. The molecular origins of these observations were examined with the help of a tube model theory that accommodates changes in polymer entanglement density during flow. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2275–2289, 2001     

Chain conformations and phase separation in polymer solutions with varying solvent quality

Molecular dynamics simulations are used to investigate the conformations of a single polymer chain, represented by the Kremer-Grest bead-spring model, in a solution with a Lennard-Jones liquid as the solvent when the interaction strength between the polymer and solvent is varied. Results show that when the polymer-solvent interaction is unfavorable, the chain collapses as one would expect in a poor solvent. For more attractive polymer-solvent interactions, the solvent quality improves and the chain is increasingly solvated and exhibits ideal and then swollen conformations. However, as the polymer-solvent interaction strength is increased further to be more than about twice the strength of the polymer-polymer and solvent-solvent interactions, the chain exhibits an unexpected collapsing behavior. Correspondingly, for strong polymer-solvent attractions, phase separation is observed in the solutions of multiple chains. These results indicate that the solvent becomes effectively poor again at very attractive polymer-solvent interactions. Nonetheless, the mechanism of chain collapsing and phase separation in this limit differs from the case with a poor solvent rendered by unfavorable polymer-solvent interactions. In the latter, the solvent is excluded from the domain of the collapsed chains while in the former, the solvent is still present in the pervaded volume of a collapsed chain or in the polymer-rich domain that phase separates from the pure solvent. In the limit of strong polymer-solvent attractions, the solvent behaves as a glue to stick monomers together, causing a single chain to collapse and multiple chains to aggregate and phase separate.     

Plastically deformable polyethylene with excellent transparency and stress whitening resistance properties fabricated by constructing massive chain entanglement

Stress whitening is one of the most prominent macroscopic defects for polyethylene (PE), which greatly affects the appearance and quality of its commodity. In order to eliminate the stress whitening defects of PE, ultrahigh molecular weight polyethylene (UHMWPE) was blended with PE to fabricated PE/UHMWPE, and the enhanced intermolecular entanglement and stretchability was achieved, which greatly suppressed and impeded the occurrence of heterogeneous plastic deformation and fibrillar bundle structure during applying tensile stress, resulting in the sharply deceased of the nanoscale cavities defects for the sample. And thus, the elimination of stress whitening defects and high-light transmittance in the visible region with excellent optical transparency performance were successfully achieved for PE/UHMWPE. Moreover, introduction of UHMWPE chains significantly improved the orientation degree and formed a dense oriented crystalline network with fine lamellae for the sample, which highly enhanced the mechanical strength of PE/UHMWPE after applying stress. This work provided a new strategy for developing stress whitening eliminating polyolefin materials with high performance, which was of great significance for sustainable development and environmental friendliness.     

Dynamic light scattering of semidilute hydrophobically modified alkali‐soluble emulsion solutions with different lengths of poly(ethylene oxide) spacer chain

Semidilute solutions of hydrophobically modified alkali‐soluble emulsion (HASE) were examined by dynamic light scattering and rheological techniques. For the model polymer without associative macromonomer, two q² dependent diffusional modes were detected in the decay time distributions. With increasing hydrophobicity of the associative macromonomer, the narrow fast peak was substituted by a shallow broad peak and only one q² dependent slow mode could be accurately detected, which indicated that the heterogeneity of these associated clusters increases with increasing carbon number. The bulk steady‐shear viscosity exhibits similar results to the diffusion coefficients of the aggregate observed from light scattering measurements. The length of poly(ethylene oxide) (PEO) spacer chain alters the solution properties as well as the associative cluster structure. With increasing length of PEO spacer chain, intramolecular association was substituted by intermolecular association. For EO segment larger than 32 units, intramolecular association dominates, where the formation of HASE aggregates is controlled by the balance of electrostatic repulsion and hydrophobic attraction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3288–3298, 2005