Soluble aromatic poly(ether amide)s containing aryl‐, alkyl‐, and chloro‐substituted phthalazinone segments

A series of novel aromatic diamines ( 2 – 4 ) containing the alkyl‐, aryl, or chloro‐substituted group of phthalazinone segments were synthesized via two synthetic steps starting from 4‐(3‐R‐4‐hydroxyphenyl)‐2,3‐phthalazinone‐1 (R = Ph, CH₃, Cl). Three series of aromatic polyamides containing phthalazinone moieties were prepared through diamines 2 – 4 reacting with different aromatic dicarboxylic acids via a direct Yamazaki–Higashi phosphorylation polycondensation reaction. The resulting aromatic polyamides had inherent viscosities in the range of 0.40–0.76 dL/g. The thermal property of the polyamides was examined with DSC and thermogravimetric analysis. The glass‐transition temperatures of these polyamides ranged from 298 to 340 °C. The 10% mass‐loss temperature was above 405 °C under nitrogen. Structures of monomers 2 – 4 and the polymers were confirmed by Fourier transform infrared spectroscopy, ¹H NMR, and mass spectrometry. Good solubility of these polymers in polar solvents such as N‐methylpyrrolidone, dimethylformamide, dimethylacetamide (DMAc), and m‐cresol was observed, and tough, flexible films were obtained from the polymer's DMAc solutions. The effect of the substituted group on the physical property of polymers was also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2026–2030, 2004     

Highly stable electrochromic polyamides based on N,N‐bis(4‐aminophenyl)‐N′,N′‐bis(4‐tert‐butylphenyl)‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine monomer, N,N‐bis(4‐aminophenyl)‐N′,N′‐bis(4‐tert‐butylphenyl)‐1,4‐phenylenediamine, was synthesized by an established synthetic procedure from readily available reagents. A novel family of electroactive polyamides with di‐tert‐butyl‐substituted N,N,N′,N′‐tetraphenyl‐1,4‐phenylenediamine units were prepared via the phosphorylation polyamidation reactions of the newly synthesized diamine monomer with various aromatic or aliphatic dicarboxylic acids. All the polymers were amorphous with good solubility in many organic solvents, such as N‐methyl‐2‐pyrrolidinone (NMP) and N,N‐dimethylacetamide, and could be solution‐cast into tough and flexible polymer films. The polyamides derived from aromatic dicarboxylic acids had useful levels of thermal stability, with glass‐transition temperatures of 269–296 °C, 10% weight‐loss temperatures in excess of 544 °C, and char yields at 800 °C in nitrogen higher than 62%. The dilute solutions of these polyamides in NMP exhibited strong absorption bands centered at 316–342 nm and photoluminescence maxima around 362–465 nm in the violet‐blue region. The polyamides derived from aliphatic dicarboxylic acids were optically transparent in the visible region and fluoresced with a higher quantum yield compared with those derived from aromatic dicarboxylic acids. The hole‐transporting and electrochromic properties were examined by electrochemical and spectro‐electrochemical methods. Cyclic voltammograms of the polyamide films cast onto an indium‐tin oxide‐coated glass substrate exhibited two reversible oxidation redox couples at 0.57–0.60 V and 0.95–0.98 V versus Ag/AgCl in acetonitrile solution. The polyamide films revealed excellent elcterochemical and electrochromic stability, with a color change from a colorless or pale yellowish neutral form to green and blue oxidized forms at applied potentials ranging from 0.0 to 1.2 V. These anodically coloring polymeric materials showed interesting electrochromic properties, such as high coloration efficiency (CE = 216 cm²/C for the green coloring) and high contrast ratio of optical transmittance change (ΔT%) up to 64% at 424 nm and 59% at 983 nm for the green coloration, and 90% at 778 nm for the blue coloration. The electroactivity of the polymer remains intact even after cycling 500 times between its neutral and fully oxidized states. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2330–2343, 2009     

Synthesis and properties of new soluble N-phenyl–substituted aromatic-aliphatic and all aromatic polyamides derived from 4,4′-dianilinobiphenyl

New N-phenylated aromatic-aliphatic and all aromatic polyamides were prepared by the high-temperature solution polycondensation of 4,4′-dianilinobiphenyl with both aliphatic (methylene chain lengths of 6–11) and aromatic dicarboxylic acid chlorides. All of the aromatic-aliphatic polyamides and the wholly aromatic polyamides exhibited an amorphous nature and good solubility in amide-type and chlorinated hydrocarbon solvents, except for those aromatic polyamides containing p-oriented phenylene or biphenylylene linkages in the backbone; the latter were crystalline and insoluble in organic solvents except m-cresol. The N-phenylated aromatic-aliphatic polyamides and aromatic polyamides had glass transition temperatures in the range of 79–116°C and 207–255°C, respectively, and all the polymers were thermally stable with decomposition temperatures above 400°C in air. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2193–2200, 1998     

Preparation and physical properties of poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) films

To prepare thermally stable and high‐performance polymeric films, new solvent‐soluble aromatic polyamides with a carbamoyl pendant group, namely poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) (p‐PDCBTA) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) (m‐PDCBTA), were synthesized. The polymers were cyclized at around 200 to 350 °C to form quinazolone and benzoxazinone units along the polymer backbone. The decomposition onset temperatures of the cyclized m‐ and p‐PDCBTAs were 457 and 524 °C, respectively, lower than that of poly(p‐phenylene terephthalamide) (566 °C). For the p‐PDCBTA film drawn by 40% and heat‐treated, the tensile strength and Young's modulus were 421 MPa and 16.4 GPa, respectively. The film cyclized at 350 °C showed a storage modulus (E′) of 1 × 10¹¹ dyne/cm² (10 GPa) over the temperature range of room temperature to 400 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 775–780, 2000     

Preparation and characterization of aromatic polyamides based on a bis(ether‐carboxylic acid) or a dietheramine extended from 1,1‐bis(4‐hydroxyphenyl)‐1‐phenylethane

Thermoplastic and organic‐soluble aromatic polyamides containing both bulky triphenylethane units and flexible ether linkages were prepared directly from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐1‐phenylethane ( III ) with various aromatic diamines or from 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenylethane ( V ) with various aromatic dicarboxylic diacids via triphenyl phosphite and pyridine. These polyamides had inherent viscosities ranging from 0.71 to 1.77 dL/g. All the polymers easily were dissolved in aprotic polar solvents such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide, and some even could be dissolved in less polar solvents such as tetrahydrofuran. The flexible and tough films cast from the polymer solutions possessed tensile strengths of 89 to 104 MPa. The polyamides were thermally stable up to 460°C in air or nitrogen. Glass‐transition temperatures of these polyamides were observed in a range of 179 to 268°C via differential scanning calorimetry or thermomechanical analysis. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 247–260, 2000     

Synthesis and properties of new soluble aromatic polyamides and polyimides on the basis of N,N′‐bis(3‐aminobenzoyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new N‐phenylated amide (N‐phenylamide) unit containing aromatic diamine, N,N′‐bis(3‐aminobenzoyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 3‐nitrobenzoyl chloride, followed by catalytic reduction. Two series of organosoluble aromatic poly(N‐phenylamide‐imide)s and poly(N‐phenylamide‐amide)s with inherent viscosities of 0.58–0.82 and 0.56–1.21 dL/g were prepared by a conventional two‐stage method and the direct phosphorylation polycondensation, respectively, from the diamine with various aromatic dianhydrides and aromatic dicarboxylic acids. All polyimides and polyamides are amorphous and readily soluble in many organic solvents such as N,N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with high tensile strengths. These polyimides and polyamides had glass‐transition temperatures in the ranges of 230–258 and 196–229 °C, respectively. Decomposition temperatures of the polyimides for 10% weight loss all occurred above 500 °C in both nitrogen and air atmospheres. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2564–2574, 2002     

Preparation and properties of new polyimides and polyamides based on 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)naphthalene

A novel, trifluoromethyl‐substituted, bis(ether amine) monomer, 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)naphthalene, was synthesized through the nucleophilic displacement of 2‐chloro‐5‐nitrobenzotrifluoride with 1,4‐dihydroxynaphthalene in the presence of potassium carbonate in dimethyl sulfoxide, followed by catalytic reduction with hydrazine and Pd/C in ethanol. A series of new fluorine‐containing polyimides with inherent viscosities of 0.57–0.91 dL/g were prepared by reacting the diamine with six commercially available aromatic dianhydrides via a conventional, two‐step thermal or chemical imidization method. Most of the resulting polyimides were soluble in strong polar solvents such as N‐methylpyrrolidone and N,N‐dimethylacetamide (DMAc). All the polyimides afforded transparent, flexible, and strong films with good tensile properties. These polyimides exhibited glass‐transition temperatures (T_g's) (by DSC) and softening temperatures (by thermomechanical analysis) in the ranges of 252–315 and 254–301 °C, respectively. Decomposition temperatures for 5% weight loss all occurred above 500 °C in both air and nitrogen atmospheres. The dielectric constants of these polyimides ranged from 3.03 to 3.71 at 1 MHz. In addition, a series of new, fluorinated polyamides with inherent viscosities of 0.32–0.62 dL/g were prepared by the direct polycondensation reaction the diamine with various aromatic dicarboxylic acids by means of triphenyl phosphite and pyridine. All the polyamides were soluble in polar solvents such as DMAc and could be solution‐cast into tough and flexible films. These polyamides had T_g's between 228 and 256 °C and 10% weight‐loss temperatures above 400 °C in nitrogen or air. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2377–2394, 2004     

Syntheses and properties of novel fluorinated polyamides based on a bis(ether‐carboxylic acid) or a bis(ether amine) extended from bis(4‐hydroxyphenyl)phenyl‐2,2,2‐trifluoroethane

Two series of novel fluorinated aromatic polyamides were prepared from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic diamines or from 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic dicarboxylic acids with the phosphorylation polyamidation technique. These polyamides had inherent viscosities ranging from 0.51 to 1.54 dL/g that corresponded to weight‐average and number‐average molecular weights (by gel permeation chromatography) of 36,200–80,000 and 17,200–64,300, respectively. All polymers were highly soluble in aprotic polar solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide, and some could even be dissolved in less‐polar solvents like tetrahydrofuran. The flexible and tough films cast from the polymer solutions possessed tensile strengths of 76–94 MPa and initial moduli of 1.70–2.22 GPa. Glass‐transition temperatures (T_g's) and softening temperatures of these polyamides were observed in the range of 185–268 °C by differential scanning calorimetry or thermomechanical analysis. Decomposition temperatures (T_d's) for 10% weight loss all occurred above 500 °C in both nitrogen and air atmospheres. Almost all the fluorinated polyamides displayed relatively higher T_g and T_d values than the corresponding nonfluorinated analogues. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 420–431, 2003     

Synthesis and characterization of new soluble aromatic polyamides based on 4‐(1‐adamantyl)‐1, 3‐bis(4‐aminophenoxy)benzene

A set of new aromatic polyamides were synthesized by the direct phosphorylation condensation of 4‐(1‐adamantyl)‐1,3‐bis‐(4‐aminophenoxy)benzene with various diacids. The polymers were produced with high yields and moderate to high inherent viscosities (0.43–1.03 dL/g), and the weight‐average molecular weights and number‐average molecular weights, determined by gel permeation chromatography, were in the range of 37,000–93,000 and 12,000–59,000, respectively. The polyamides were essentially amorphous and soluble in a variety of solvents such as N,N‐dimethylacetamide (DMAc), cyclohexanone, and tetrahydrofuran. They showed glass‐transition temperatures in the range of 240–300 °C (differential scanning calorimetry) and 10% weight‐loss temperatures over 450 °C, as revealed by thermogravimetric analysis in nitrogen. All the polymers gave strong films via casting from DMAc solutions, and these films exhibited good mechanical properties, with tensile strengths in the range of 77–92 MPa and tensile moduli between 1.5 and 2.5 GPa. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1014–1023, 2000     

Fluorinated polyamides and poly(amide imide)s based on 1,4‐bis(4‐amino‐2‐trifluromethylphenoxy)benzene,aromatic dicarboxylic acids,and various monotrimellitimides and bistrimellitimides: Syntheses and properties

A CF₃‐containing diamine, 1,4‐bis(4‐amino‐2‐trifluromethylphenoxy) benzene ( I ), was prepared from hydroquinone and 2‐chloro‐5‐nitrobenzotrifluoride. Imide‐containing diacids ( V _a–h and VI _a,b ) were prepared through the condensation reaction of amino acids, aromatic diamines, and trimellitic anhydride. Then, a series of soluble fluorinated polyamides ( VII _a–h ) and poly(amide imide)s ( VIII _a–h and X _a,b ) were synthesized from I with various aromatic diacids ( II _a–h ) and imide‐containing diacids ( V _a–h and VI _a,b ) via direct polycondensation with triphenyl phosphate and pyridine. The polyamides and poly(amide imide)s had inherent viscosities of 1.00–1.70 and 0.79–1.34 dL/g, respectively. All the synthesized polymers showed excellent solubility in amide‐type solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, and N‐dimethylformamide and afforded transparent and tough films via solvent casting. Polymer films of VII _a–h , VIII _a–h , and X _a,b had tensile strengths of 91–113 MPa, elongations to break of 8–40%, and initial moduli of 2.1–2.8 GPa. The glass‐transition temperatures of the polyamides and poly(amide imide)s were 254–276 and 255–292 °C, respectively, and the imide‐containing poly(amide imide)s had better thermal stability than the polyamides. The polyamides showed higher transparency and were much lighter in color than the poly(amide imide)s, and their cutoff wave numbers were below 400 nm. In comparison with isomeric IX _{c – h} , poly(amide imide)s VIII _c–h exhibited less coloring and showed lower yellowness indices. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3116–3129, 2004     

Synthesis and properties of new aromatic polyamides with redox‐active 2,4‐dimethoxytriphenylamine moieties

A new triphenylamine‐based diamine monomer, 4,4′‐diamino‐2″,4″‐dimethoxytriphenylamine ( 2 ), was synthesized from readily available reagents and was reacted with various aromatic dicarboxylic acids to produce a series of aromatic polyamides ( 4a–h ) containing the redox‐active 2,4‐dimethoxy‐substituted triphenylamine (dimethoxyTPA) unit. All the resulting polyamides were readily soluble in polar organic solvents and could be solution cast into tough and flexible films. These polymers exhibited good thermal stability with glass transition temperatures of 243–289 °C and softening temperatures of 238–280 °C, 10% weight loss temperatures in excess of 470 °C in nitrogen, and char yields higher than 60% at 800 °C in nitrogen. The redox behaviors of the polymers were examined using cyclic voltammetry (CV). All these polyamides showed two reversible oxidation processes in the first CV scan. The polymers also displayed low ionization potentials as a result of their dimethoxyTPA moieties. In addition, the polymers displayed excellent stability of electrochromic characteristics with coloration change from a colorless neutral state to green and blue‐purple oxidized states. These anodically coloring polyamides showed high green coloration efficiency (CE = 329 cm²/C), high contrast of optical transmittance change (ΔT% = 84% at 829 nm), and long‐term redox reversibility. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3392–3401, 2010     

Novel thermally stable triarylamine‐containing aromatic polyamides bearing anthrylamine chromophores for highly efficient green‐light‐emitting materials

A series of novel polyamides with pendent anthrylamine units were prepared via the direct phosphorylation polycondensation from various diamines and the anthrylamine‐based aromatic dicarboxylic acid, 9‐[N,N‐di(4‐carboxyphenyl)amino]anthracene (4). The aromatic polyamides had useful levels of thermal stability associated with relatively high softening temperatures (T_s) (290–300 °C), 10% weight‐loss temperatures (T_d¹⁰) nearly in excess of 550 °C, and char yields at 800 °C in nitrogen higher than 60%. These aromatic polyamides I exhibited highly photoluminescence quantum yield in NMP solution ranges from 55% for Ia to 74% for Ie due to the introduction of anthrylamine chromophores. Cyclic voltammograms of the polyamide films cast onto an indium‐tin oxide (ITO)‐coated glass substrate exhibited one oxidation and reduction couples (E_onset) around 1.10 and ?1.50 V versus Ag/AgCl in acetonitrile (CH₃CN) and DMF solutions, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7354–7368, 2008     

Synthesis and characterization of new soluble polyamides from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐4‐tert‐butylcyclohexane and various diamines

A new dicarboxylic acid monomer, 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐4‐tert‐butylcyclohexane, bearing a pendent tert‐butylcyclohexylidene group was prepared in three steps from 4‐tert‐butylcyclohexanone. The monomer was reacted with various diamines to produce a series of new polyamides with triphenyl phosphite and pyridine as condensing agents. These polyamides were produced with inherent viscosities of 0.74 to 1.02 dL g⁻¹. All the polymers were characterized by X‐ray diffraction that revealed this amorphous nature. These polymers exhibited excellent solubility in a variety of solvents. Almost all the polymers could be dissolved in N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide, dimethyl sulfoxide, pyridine, and even in tetrahydrofuran and cyclohexanone. These polymers showed glass‐transition temperatures between 223 and 256 °C and decomposition temperatures at 10% weight loss ranging from 468 to 491 °C and 469 to 498 °C in nitrogen and air atmospheres, respectively. Transparent, tough, and flexible films of these polymers were cast from the DMAc solutions. These polymer films had tensile strengths ranging from 76 to 99 MPa, elongations at break from 7 to 19%, and initial moduli from 2.1 to 2.7 GPa. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 797–803, 2000     

Synthesis and characterization of new organosoluble polyamides derived from bis[4‐(4‐carboxyphenoxy) phenyl]diphenylmethane

A new dicarboxylic acid containing a diphenylmethylene linkage, bis[4‐(4‐carboxyphenoxy)phenyl]diphenylmethane (BCAPD), was prepared from bis(4‐hydroxphenyl)diphenylmethane and p‐fluorobenzonitrile via an aromatic nucleophilic substitution reaction followed by hydrolysis. A series of novel polyamides were prepared by the direct polycondensation of BCAPD and various aromatic diamines. The polymers were produced with moderate to high inherent viscosities of 0.80–0.85 dL g^?1. Nearly all the polymers were readily soluble in polar solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide, in less polar solvents such as pyridine and cyclohexanone, and in tetrahydrofuran. All the polymers were amorphous, and the polyamide films had a tensile strength and a tensile modulus greater than 80 MPa and 2.0 GPa, respectively. These polyamides had glass‐transition temperatures between 249 and 274 °C, and their temperatures at a 10% weight loss were 477–538 and 483–540 °C in nitrogen and air atmospheres, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1156–1161, 2001     

Synthesis and properties of novel soluble polyamides having ether linkages and laterally attached p‐terphenyl units

A new ether‐bridged aromatic dicarboxylic acid, 2′,5′‐bis(4‐carboxyphenoxy)‐p‐terphenyl ( 3 ), was synthesized by the aromatic fluoro‐displacement reaction of p‐fluorobenzonitrile with 2′,5′‐dihydroxy‐p‐terphenyl in the presence of potassium carbonate, followed by alkaline hydrolysis. A set of new aromatic polyamides containing ether and laterally attached p‐terphenyl units was synthesized by the direct phosphorylation polycondensation of diacid 3 with various aromatic diamines. The polymers were produced with high yields and moderately high inherent viscosities (0.44–0.79 dL/g). The polyamides derived from 3 and rigid diamines, such as p‐phenylenediamine and benzidine, and a structurally analogous diamine, 2′,5′‐bis(4‐aminophenoxy)‐p‐terphenyl, were semicrystalline and insoluble in organic solvents. The other polyamides were amorphous and organosoluble and could afford flexible and tough films via solution casting. These films exhibited good mechanical properties, with tensile strengths of 91–108 MPa, elongations to break of 6–17%, and initial moduli of 1.95–2.43 GPa. These polyamides showed glass‐transition temperatures between 193 and 252 °C. Most of the polymers did not show significant weight loss before 450 °C, as revealed by thermogravimetric analysis in nitrogen or in air. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4056–4062, 2004     

Regeneration of polycondensation of wholly aromatic poly(azomethine)s with 1,5‐ or 2,6‐substituted naphthalene moiety in main chain

Wholly aromatic poly(azomethine)s with 1,5‐ or 2,6‐substituted naphthalene moiety in the main chains were prepared in aprotic polar solvents or m‐cresol under various reaction conditions. In the polymerization of 1,5‐diaminonaphthalene with terephthalaldehyde, the polymer that synthesized in (HMPA/DMSO) at room temperature for 24 h by adding 5 wt % of calcium chloride and a very small amount of p‐toluenesulfonic acid showed the highest reduced viscosity in all of the polymers from 1,5‐diaminonaphthalene. The reduced viscosity of poly(azomethine)s synthesized from 2,6‐diaminonaphthalene with 2,6‐diformylnaphthalene in m‐cresol and with terephthalaldehyde in HMPA/DMSO were η_red = 0.35 and 0.36, respectively. The thermal analysis showed the poly(azomethine)s had high thermal stability and the glass‐transition temperatures of these polymers are about 250 °C. The X‐ray diffraction showed that they are partially crystalline. They could be polymerized again by second stage polycondensation in polyphosphoric acid. The reduced viscosities of the obtained polymers were about 2–5 times as high as that of the pristine polymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1064–1072, 2000     

Syntheses and properties of organosoluble polyamides and polyimides based on the diamine 3,3‐bis[4‐(4‐aminophenoxy)‐3‐methylphenyl]phthalide derived from o‐cresolphthalein

Diamine 3,3‐bis[4‐(4‐aminophenoxy)‐3‐methylphenyl]phthalide (BAMP) was derived from the o‐cresolphthalein, and then it was polycondensated with various aromatic dicarboxylic acids and dianhydrides to synthesize polyamides (PAs) and polyimides (PIs), respectively. PAs have inherent viscosities of 0.78–2.24 dL/g. Most of the PAs are readily soluble in a variety of solvents such as DMF, DMAc, and NMP and afforded transparent and tough films from DMAc solutions. The cast films have tensile strengths of 75–113 MPa as well as initial moduli of 1.71–2.97 GPa. These PAs have glass transition temperatures (T_gs) in the range of 242–325°C, 10% weight loss temperatures occur up to 473°C, and char yields are between 57 and 64% at 800°C in nitrogen. PIs were first synthesized to form polyamic acids (PAAs) by a two‐stage procedure that included a ring‐opening reaction, followed by thermal or chemical conversion to polyimides. Inherent viscosities of PAAs are between 0.71 and 1.63 dL/g. Most of the PIs obtained through the chemical cyclodehydration procedure are soluble in NMP, o‐chlorophenol, m‐cresol, etc., and they have inherent viscosities of 0.58–1.32 dL/g. T_gs of these PIs are in the range of 270–305°C and show 10% weight loss temperatures up to 477°C. PIs obtained through the thermal cyclodehydration procedure have tensile strengths of 72–142 MPa, elongations at break of 8–19%, and initial moduli of 1.80–2.72 GPa. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 455–464, 1999     

Crystal structures of four δ‐keto esters and a Cambridge Structural Database analysis of cyano–halogen interactions

The revived interest in halogen bonding as a tool in pharmaceutical cocrystals and drug design has indicated that cyano–halogen interactions could play an important role. The crystal structures of four closely related δ‐keto esters, which differ only in the substitution at a single C atom (by H, OMe, Cl and Br), are compared, namely ethyl 2‐cyano‐5‐oxo‐5‐phenyl‐3‐(piperidin‐1‐yl)pent‐2‐enoate, C₁₉H₂₂N₂O₃, (1), ethyl 2‐cyano‐5‐(4‐methoxyphenyl)‐5‐oxo‐3‐(piperidin‐1‐yl)pent‐2‐enoate, C₂₀H₂₄N₂O₄, (2), ethyl 5‐(4‐chlorophenyl)‐2‐cyano‐5‐oxo‐3‐(piperidin‐1‐yl)pent‐2‐enoate, C₁₉H₂₁ClN₂O₃, (3), and the previously published ethyl 5‐(4‐bromophenyl)‐2‐cyano‐5‐oxo‐3‐(piperidin‐1‐yl)pent‐2‐enoate, C₁₉H₂₁BrN₂O₃, (4) [Maurya, Vasudev & Gupta (2013). RSC Adv. 3 , 12955–12962]. The molecular conformations are very similar, while there are differences in the molecular assemblies. Intermolecular C—H...O hydrogen bonds are found to be the primary interactions in the crystal packing and are present in all four structures. The halogenated derivatives have additional aromatic–aromatic interactions and cyano–halogen interactions, further stabilizing the molecular packing. A database analysis of cyano–halogen interactions using the Cambridge Structural Database [CSD; Groom & Allen (2014). Angew. Chem. Int. Ed. 53 , 662–671] revealed that about 13% of the organic molecular crystals containing both cyano and halogen groups have cyano–halogen interactions in their packing. Three geometric parameters for the C—X...N[triple‐bond]C interaction (X = F, Cl, Br or I), viz. the N...X distance and the C—X...N and C—N...X angles, were analysed. The results indicate that all the short cyano–halogen contacts in the CSD can be classified as halogen bonds, which are directional noncovalent interactions.     

Synthesis and characterization of novel soluble triphenylamine‐containing aromatic polyamides based on N,N′‐bis(4‐aminophenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine, N, N′‐bis(4‐aminophenyl)‐N, N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 4‐fluoronitrobenzene, followed by catalytic reduction. A series of novel aromatic polyamides with triphenylamine units were prepared from the diamine and various aromatic dicarboxylic acids or their diacid chlorides via the direct phosphorylation polycondensation or low‐temperature solution polycondensation. All the polyamides were amorphous and readily soluble in many organic solvents such as N, N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with good mechanical properties. They had useful levels of thermal stability associated with relatively high glass‐transition temperatures (257–287 °C), 10% weight‐loss temperatures in excess of 550 °C, and char yields at 800 °C in nitrogen higher than 72%. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2810–2818, 2002     

Synthesis and characterization of new soluble aromatic polyamides derived from 1,4‐Bis(4‐carboxyphenoxy)‐2, 5‐di‐tert‐butylbenzene

Aromatic polyamides based on a novel bis(ether‐carboxylic acid) were synthesized by the direct phosphorylation condensation method. 1,4‐Bis(4‐carboxyphenoxy)‐2,5‐di‐tert‐butylbenzene was combined with various diamines containing flexible linkages and side substituents to render a set of eight novel aromatic polyamides. The polymers were produced with high yields and moderate to high inherent viscosities (0.49–1.32 dL/g) that corresponded to weight‐average and number‐average molecular weights (by gel permeation chromatography) of 31,000–80,000 and 19,000–50,000, respectively. Except for a single example, the polyamides were essentially amorphous and soluble in a variety of common solvents such as cyclohexanone, dioxane, and tetrahydrofuran. They showed glass‐transition temperatures of 250–295 °C (by differential scanning calorimetry) and 10% weight loss temperatures above 460 °C, as revealed by thermogravimetric analysis in nitrogen. Polymer films, obtained by casting from N,N‐dimethylacetamide solutions, exhibited good mechanical properties, with tensile strengths of 83–111 MPa and tensile moduli of 2.0–2.2 GPa. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 475–485, 2001